ShoreLand'r LUV2314SW User Manual V.2
®
LUV2314SW
LUV2314SW-01 Lund Trailer 2x4 V2314SW
*ST215/75R14C GY TS Dir Rim
8056201 Frame Bundle LUV2314SW
61395 Coupler Bag with Chains
62340 Lit Packet - ShoreLand’r Trailers
LUV2314SW-03 Lund Trailer 2x4 V2314SW
*ST215/75R14C GY TS Dir Rim
8056203 Frame Bundle LUV2314SW
61395 Coupler Bag with Chains
62340 Lit Packet - ShoreLand’r Trailers
LUV2314SW-14 Lund Trailer 2x4 V2314SW
*ST215/75R14C GY TS Dir Rim
8056214 Frame Bundle LUV2314SW
61395 Coupler Bag with Chains
62340 Lit Packet - ShoreLand’r Trailers
LUV2314SW-22 Lund Trailer 2x4 V2314SW
*ST215/75R14C GY TS Dir Rim
8056222 Frame Bundle LUV2314SW
61395 Coupler Bag with Chains
62340 Lit Packet - ShoreLand’r Trailers
LUV2314SW-39 Lund Trailer 2x4 V2314SW
*ST215/75R14C GY Galv Dir Rim
8056239 Frame Bundle LUV2314SW
61395 Coupler Bag with Chains
62340 Lit Packet - ShoreLand’r Trailers
*Check with your dealer/customer service representative for current tire/rim assembly part number.
ShoreLand’r offers their product line in either galvanized or paint-
ed nish. When ordering parts it is important that you specify the
nish or color you have on your product. The ve (5) digit number
along with a two (2) digit space _ _, note the parts which can be
purchased with various nishes. When ordering these items use
the ve (5) digit number along with a two (2) digit sufx for the
proper nish.
01.........White
03.........Black
14 ......... Blue
22 ......... Red
24 ......... Majestic Red
39 ......... Galvanized w/Silver Plastic Components
LUV2314SW-24 Lund Trailer 2x4 V2314SW
*ST215/75R14C GY TS Dir Rim
8056224 Frame Bundle LUV2314SW
61395 Coupler Bag with Chains
62340 Lit Packet - ShoreLand’r Trailers
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003808
Page 1 06/05/07
Diagram A
1
2
4
5
6
11
18
23
28
SEE DETAIL A
SEE DETAIL B
SEE DETAIL C
3
8
9
17
20
21
22
26
31
DETAIL A
SCALE 0.070
25
7
16
27
29
DETAIL B
SCALE 0.070
10
12
13
14
15
19
24
30
DETAIL C
SCALE 0.070
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003808
Page 2 06/05/07
FINAL ASSEMBLY INSTRUCTIONS
ITEM PART # DESCRIPTION QTY
NOTE
1 61395 COUPLER BAG WITH CHAINS 1
2 66494 PROFILE 2000 WINCH CASE ASSY 1
3 68271 TONGUE COVER PLATE 1
4 69268 FRAME WMENT 2X4X80W 190 LUND 1
5 69308 SWINGTONGUE ASSY 55IN NON BRAKE FG 1
6 69337 BUNK ASSY BUNDLE LUB29CBLW 2
7 0110059 HH 3/8-16 X 3 3/4 CS GR 5 4
8 0110114 HH 1/2-13 X 4 CS GR5 1
9 0140094 HH 1/2-13 X 1 1/2 CS GR 5 1
10 0210130 CARR 3/8-16 X 3 3/4 GR5 2
11 0210218 CARR 1/2-13 X 4 GR5 3
12 0810965 SCREW #10 X 1 1/2 SQ PAN SELF DRILL 2
13 1340030 LOCKWASHER 3/8 S/T MED ULTRASEAL 2
14 1340095 WASHER USS FLAT 3/8 2
15 1410109 HEX NUT 3/8-16 2
16 1440101 HEX LOCKNUT FLANGE 3/8-16 W/T& T 4
17 1440102 HEX LOCKNUT FLANGE 1/2-13 W/T& T 5
18 2400026 TIE DOWN RETRACTABLE 2
19 3510022 GROMMET 7/16IN MOLDED 1
20 3510030 GROMMET 7/8IN MOLDED 8
21 3510158 PLASTIC DRIVE RIVOT 4
22 3510253 LIGHT BEZEL - AMBER 2
23 3510368 TAILLIGHT STEP PAD TREAD TAP E 2
24 3510542 MOLDED REAR CROSSMEMBER PAD 2
25 3510597 GROMMET 13/16IN WITH SPLIT 9/16I D 2
- 4850414 DECAL LUND LARGE CHROME 2
- 4850417 DECAL LUND CHROME WING LARGE LEFT 1
- 4850418 DECAL LUND CHROME WING LARGE RIGH T 1
26 5110127 REFLECTOR ANDERSON AMBER 2
27 5110348 BO LICENSE PLATE BRACKET 1
- 5110561 HARNESS TONGUE 5WIRE FULL GROUND 1
- 5110565 HARNESS FRAME 214" FULL GROUND RT 1
- 5110566 HARNESS FRAME 214" FULL GROUND LT 1
28 5110569 TAILLIGHT RIGHT LED PETERSON 1
29 5110570 TAILLIGHT LEFT LED PETERSON 1
30 5110571 LIGHT CLUSTER THREE LED 1
31 5110572 MARINE YELLOW CLEARANCE LIGH T 2
Remove the hardware bag from the frame, remove parts and sort
by size. Remove all the banded items from the frame.
TONGUE
Install the swing tongue by sliding it in the front of the tongue channel. Line the holes in the tongue with the holes in the tongue chan-
nel. Install the 1/2” x 4” hex bolt in the front cross hole and secure
with a 1/2” lock nut.
Remove the wire harness from the rear of the tongue. Place it
through the hole provided in the tongue cover plate.
Secure the tongue cover plate in position with the same 1/2” x 11/2” hex bolt that secures the back of the tongue to the tongue
channel of the frame. Secure with a 1/2” lock nut. Tighten both bolts
just installed.
Plug the tongue wire harness into the frame harnesses by match-
ing colors and ends. Push the extra wire provided either into the
rear of the tongue or else remove the grommets in the side frame
and place the extra wire in the side frame. Replace grommets just
removed.
SAFETY CHAINS
Locate a 3/8” x1 1/4” hex bolt. Slip the bolt through a 3/8” at washer, then place through the last link of one of the safety chains.
LUV2314SW (All Colors) Specications:
Capacity: 2300 lbs.
GVWR: 2995 lbs.
GAWR: 2995 lbs.
Ship Wt: 575 lbs.
Frm Size: 2X4 (11 Ga)
Tire Size: ST215/75R14-C
Rim Size: 14 X 6 “J”
Brake: N/A
Coupler: 2”
Safety Chn: 7600 lb.
Suspension: 5 Leaf Hook Springs
Tongue Size: 3 X 5 X 65” Swing Tongue
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003808
Page 3 06/05/07
Place the bolt with chain attached through the hole provided in the
bottom front of the tongue. Secure with a 3/8” ange lock nut. Tighten. Repeat on the other side and safety chain.
RETRACTABLE TIE DOWNS
Locate the two retractable tie downs. Next locate one of the 7/16”
x 1 ½” ne threaded bolts supplied with the retractable tie down.
Insert it into the bottom hole on the retractable tie down so the bolt
is pointing through the back side of the tie down. Insert the bolt
through the hole provided in the taillight bracket just inside the side
frame. Secure with the 7/16” ange lock nut. Tighten.
Repeat the above process on the other tie down.
WINCH POST ASSEMBLY
Your trailer may have come with the jack already installed on the
winch base. However, in the event that it did not, use the following
instructions to attach the jack to the winch base before it is installed
on the tongue.
ASSEMBLY AND MOUNTING INSTRUCTIONS:
JACK ON A PROFILE 2000 WINCH BASE
The Prole 2000 winch base used on the 2” x 4” and 2” x 5” frame
trailers is formed so that the jack can be mounted directly to it eliminating the need for other mounting hardware for attaching the jack
to the tongue. The jack required for mounting does not require the
mounting base or any of the original mounting hardware components.
Assemble as follows:
The jack must be mounted to the winch base before it is installed
on the trailer tongue. If the winch base is already mounted on the
tongue, it will have to be removed for the jack installation.
Locate the hardware bag and sort all items by size.
Lay the Prole 2000 winch base on its side so the side that the jack
Loading...