ShoreLand'r LUB7TSS User Manual V.1
®
BUNDLES REQUIRED
LUB7TSS-03 Lund Trailer Fishing - Tadpul
62340 Literature Bag - Trailers
4850413 Decal - Lund Small
6728003 Frame Bundle - Tadpul
*4.80 X 12B Tire/Mod Rim
6938903 Tongue Assy 3X3X13
3310050 Jack 800 lb. Swivel
3310053 Jack Mounting Hardware Bag
LUB7TSS
LUB7TSS-39 Lund Trailer Fishing - Tadpul
62340 Literature Bag - Trailers
4850413 Decal - Lund Small
6728039 Frame Bundle - Tadpul
*4.80 X 12B Tire/Mod Rim
6938900 Tongue Assy 3X3X13
3310050 Jack 800 lb. Swivel
3310053 Jack Mounting Hardware Bag
*Check with your dealer/customer service representative for current tire/rim assembly part number.
ShoreLand’r offers their product line in either galvanized or painted
nish. When ordering parts it is important that you specify the nish
or color you have on your product. The ve (5) digit number along
with a two (2) digit space _ _, note the parts which can be purchased
with various nishes. When ordering these items use the ve (5) digit
number along with a two (2) digit sufx for the proper nish.
03..........Black
39..........Galvanized W/Silver Plastic Components
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003743
Rev A 01/26/2009
Page 1
Tire Size & Carrying Capacity Chart
Tire Size: 4.80 X 12
Load Range: B
Carrying Capacity: 780 lbs. per/tire
Refer to tire side wall for correct tire pressure.
Tongue Weight Adjustment
Approximate Tongue Weights for Best Towing. Slide the water
vehicle either forward or backward on the trailer until the proper
tongue weight has been achieved. The tongue weight should be 5%
to 7% of the total gross weight of the trailer and boat combined.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003743
Rev A 01/26/2009
Page 2
Final Assembly Instructions
Remove the small parts from the frame by cutting the banding. Remove the bolt bag and sort all the nuts and bolts by size.
See Detail A
Side Marker Lights
Once the proper tongue is identied place it on the stands so it can
be prepared for installation into the frame. Locate the two amber
side marker lights shipped in the hardware box. Uncoil the wire and
insert the plug end into the larger, center hole that is drilled in the
side of the tongue. As the wire is inserted into the hole direct the wire
so that it will go to the forward end of the tongue. Pull the wire out
the front of the tongue. It will be connected to the tongue har¬ness
at a later time. Attach the light to the tongue using two (2) No. 10 x
3/4” self-tapping screws provided. Repeat this process on the other
light on the other side of the tongue.
Locate the tongue wire harness. Insert the end of the harness with
the small plug into the hole located in the top of the tongue. Pull the
wire backward through the tongue until the end comes out the rear
of the tongue. As the wire harness is inserted note that there are two
single bullet wires towards the front plug of the tongue wire harness.
Pull these wires forward as the wire harness is inserted into the
tongue. Plug the single wires from the side marker lights installed
earlier into the two single bullets of the tongue harness. Push the
additional back into the front of the tongue to keep it from damage
during use. Place a rubber grommet around the wire har¬ness and
in the hole in the top of the tongue to protect the wires from damage during use.
Route the harness plug at the rear of the tongue through the hole
provided in the side of the tongue. Pull both the plug and the white
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003743
Rev A 01/26/2009
Page 3
Loading...