ShoreLand'r LUB14TS User Manual
®
LUB14TS
BUNDLES REQUIRED
LUB14TS-03 Lund Trailer Fishing
62340 Literature Bag - Trailers
6552203 Hdwe Box - Bunk - 56” Fishing Series
6924803 Frame Bundle - Lund 56” w/Fish Bunk
* 5.30 X 12C Tire/Mod Rim
6578003 Tongue Assy 3X3X7’
3310050 Jack 1000 lb. Swivel
3310053 Jack Mounting Hardware Bag
LUB14TS-39 Lund Trailer Fishing
62340 Literature Bag - Trailers
6552200 Hdwe Box - Bunk - 56” Fishing Series
6924839 Frame Bundle - Lund 56” w/Fish Bunk
* 5.30 X 12C Tire/Mod Rim
6578000 Tongue Assy 3X3X7’
3310050 Jack 1000 lb. Swivel
3310053 Jack Mounting Hardware Bag
*Check with your dealer/customer service representative for current tire/rim assembly part number.
ShoreLand’r offers their product line a painted nish. When ordering
parts it is important that you specify the nish or color you have on
your product. The ve (5) digit number along with a two (2) digit space
_ _, note the parts which can be purchased with various nishes.
When ordering these items use the ve (5) digit number along with
a two (2) digit sufx for the proper nish.
03..........Black
39..........Galvanized w/Silver Plastic Components
Tire Size and Carrying Capacity Chart
Tire Size ............................5.30 X 12-C
GVWR ...............................2000 lb.
Carrying Capacity ............1400 lb.
Axle ...................................Non-Brake
Refer to the tire side wall for correct tire pressure.
NOTE: Brakes available as optional equipment.
Recommended carrying capacity is based on shipping weight
of the trailer with standard equipment. Adding optional equipment may decrease the trailer’s carrying capacity.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0004409
07/28/2011
Page 1
Diagram A
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0004409
07/28/2011
Page 2
TONGUE ASSEMBLY
Place the frame to be assembled on saw horses or stands to assist
in the assembly. Remove all items that are banded to the frame.
Sort the items in the hardware box by item and the hardware by
size.
Locate the tongue for the trailer.
See Diagram A
Push the additional back into the front of the tongue to keep it from
damage during use. Place a rubber grommet around the wire harness and in the hole in the top of the tongue to protect the wires
from damage during use.
Route the harness plug at the rear of the tongue through the hole
provided in the side of the tongue. Pull both the plug and the white
ground wire out the hole. They will be attached later once the
tongue is installed in the frame.
Place tongue on the stands so it can be prepared for installation
into the frame. Locate the two amber side marker lights shipped in
the hardware box. Uncoil the wire and insert the plug end into the
larger, center hole that is drilled in the side of the tongue. As the
Locate the safety chains. Place a 3/8” at washer on a 3/8” x 1-1/4”
hex bolt. Insert the bolt through the last link in the safety chain and
then into the lower hole provided in the front of the tongue. Secure
with a 3/8” ange lock nut. Tighten. Repeat on the other chain.
wire is inserted into the hole direct the wire so that it will go to the
forward end of the tongue. Pull the wire out the front of the tongue.
It will be connected to the tongue harness at a later time. Attach the
light to the tongue using two (2) No. 10 x 3/4” self-tapping screws
provided. Repeat this process on the other light on the other side
Place the coupler on the top of the tongue. Align the holes in the
coupler with the holes in the tongue. Place a 1/2” x 4” hex bolt
through the back holes of the coupler and the tongue. Secure with
a 1/2” ange lock nut but do not tighten at this point.
of the tongue.
Place a 1/2” x 1” hex bolt through the front hole on one side of the
Locate the tongue wire harness. Insert the end of the harness with
the small plug into the hole located in the top of the tongue. Pull
the wire backward through the tongue until the end comes out the
rear of the tongue. As the wire harness is inserted note that there
coupler and the tongue so that the head of the bolt is to the outside.
Place a 1/2” ange lock nut on the bolt inside the tongue. Repeat
this process on the other side of the tongue. Once the bolts are
installed, tighten all nuts left loose at this time.
are two single bullet wires towards the front plug of the tongue wire
harness. Pull these wires forward as the wire harness is inserted
into the tongue. Plug the single wires from the side marker lights
installed earlier into the two single bullets of the tongue harness.
Insert the tongue assembly through the front channel of the frame
far enough so the rear of the tongue is inserted into the front cross
member. Align the cross hole in the front channel and the tongue
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0004409
07/28/2011
Page 3
Loading...