ShoreLand'r B2313SW User Manual
®
SLB2313SW
SLB2313SW Bundles Required:
ST185/80R13C MR Tire/TS Dir Rim ...........2
(or)
ST185/80R13C MR Tire/Galv Dir Rim ........2
61395 Coupler Bag with Chains ............................1
62340 Literature Bag - Trailers .............................. 1
80244-- Frame Bundle - 2X4W B23SW ................... 1
67757-- Tongue Assembly 55”, Non Brake .............. 1
ShoreLand’r offers their product line in either galvanized or
painted nish. When ordering parts it is important that you
specify the nish or color you have on your product. The ve
(5) digit number along with a two (2) digit space _ _, note the
parts which can be purchased with various nishes. When
ordering these items use the ve (5) digit number along with
a two (2) digit sufx for the proper nish.
00..........Galvanized
01..........Arctic White
03..........Black
33..........Galvanized w/Black Plastic Parts
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003397
Page 1 REV A 8/30/06
Table of Contents: Page
Frame Drawing & Bill of Materials ................................2-3
Safety Instructions ........................................................3
Tongue & Safety Chain Dwg/BOM. ..............................4
Prole 2000 Winch Dwg/BOM/Assy Instr. .................... 5-6
Chassis Drawing & Bill of Materials ..............................7
Spring Assembly Instructions ....................................... 8
Axle Assembly Instructions ...........................................8
Tire & Wheel Assembly ................................................8
Tire Size & Carrying Capacity Chart .............................8
Bunk Assembly Instructions..........................................9
Trailer Adjustments .......................................................10
Axle Adjustments .......................................................... 10
Winch Post Adjustments ...............................................10
Diagram A
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove
parts and sort by size.
TONGUE
The tongue is shipped separate of the frame. Locate
the appropriate tongue and install by sliding it in the
front of the tongue channel.
Line the holes in the tongue with the holes in the
tongue channel. Install the 1/2” x 4” hex bolt in the front
cross hole and secure with a 1/2” lock nut.
Remove the wire harness from the rear of the
tongue. Place the wire harness and the brake line (If
equipped with brakes) through the hole provided in
the tongue cover plate.
Secure the tongue cover plate in position with the same
1/2” x 1-1/2” hex bolt that secures the back on the
tongue to the tongue channel of the frame. Secure with
a 1/2” lock nut. Tighten both bolts just installed.
Plug the tongue wire harness ends into the frame
harnesses by matching colors and ends. Push the
extra wire provided either into the rear of the tongue
or else remove the grommet in the side frame and
place the extra wire in the side frame. Replace
grommet just removed.
SAFETY CHAINS
Locate the 1/2” x 5” hex bolt. Slip the bolt through a
1/2” at washer, then place through the last link of
one of the safety chains.
Place the bolt with chain attached through the hole
provided in the bottom front of the actuator mount on
the tongue. Place the second chain on the portion of
the bolt extending through the other side of the tongue.
Place on another 1/2” at washer and hex lock nut.
Tighten.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003397
Page 2 REV A 8/30/06
Refer to your ShoreLand’r Owner’s
Guide and other decals on trailer for
additional information.
SAFETY INSTRUCTIONS
4810709
Proper tongue weight must be maintained.
Rev C 8/28/06
Before towing, check the following to ensure
that:
1. All parts, bolts, nuts and wheel lug nuts
are tight.
2. All wheel lug nuts must be tightened to a
minimum torque rating of 85 ft/lb.
3. Lug nuts must be re-torqued after the
first 50 miles, then periodically thereafter.
4. Tires are inflated to manufacturer’s
standards. (See tire sidewall)
5. Wheel bearings have adequate grease.
6. Trailer coupler and coupler ball are the
same size.
7. Hitch ball has a rating that is equal to or
greater than the coupler or actuator
GVWR.
8. Coupler is properly attached and
secured to coupler ball.
9. Trailer safety chains are crossed under
the tongue and attached to towing
vehicle.
10. All lights are operational. Note: It is
recommended that the trailer lights be
disconnected before backing into the
water.
11. Tie downs, winch strap and bow eye safety chain are secure.
12. Trailer tongue jack is in up or travel
position.
Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003397
Page 3 REV A 8/30/06
Loading...