ShoreLand'r 2200U User Manual

®

2200U & 2200UA

Bundles Required

2200U Utility Trailer W/Ramp & Front Stop

2 *20.5 X 8 X 10-E Tire/Rim
1 65069 Literature Packet - Utility
1 6788803 Frame Bundle - 2200U

2200UA Utility Trailer W/Ramp & Front Stop

2 *ST185/80R13-C Tire/Dir Rim
1 65069 Literature Packet - Utility
1 6791903 Frame Bundle - 2200UA

*Check with your dealer/customer service representative for current tire/rim assembly
part number.

2200UA is shown

Tire Size & Carrying Capacity Chart

Tire Size 20.5 X 8 X 10 or ST185/80R13
Load Range E or C
Carrying Capacity 1535 lbs. per/tire or
1480 lbs. per/tire
Refer to the tire side wall for the correct tire
pressure.

Tongue Weight Adjustment

Approximate Tongue Weight for Best Towing.

NOTE: Axle is NOT adjustable.

Shift load to obtain proper tongue weight. Tongue
weight should be 5-7% of total gross weight of
trailer and load combined.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003618

Page 1 2/02/06

2200U

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003618

Page 2 2/02/06

2200U

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003618

Page 3 2/02/06

2200UA

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003618

Page 4 2/02/06

2200UA

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003618

Page 5 2/02/06

Tools Required for Assembly

9/16” Wrench / Socket 7/8” Wrench / Socket
13/16” Wrench / Socket 3/4” Wrench / Socket
5/16” Socket

Assembly Instructions

Safety Chain:

Insert 3/8” X 1-1/4” hex bolt with 3/8” flat washer and safety
chain through the lower hole on front of tongue. Secure with
3/8” flat washer and 3/8” flange lock nut. Repeat procedure
on opposite side of tongue.

Coupler:

Mount coupler to tongue using two (2) 1/2” X 1” hex bolt
to front holes and one (1) 1/2” X 4” hex bolt in rear hole of
coupler. Secure with 1/2” flange lock nuts.

Axle/Springs:

Mount leaf spring to axle assembly using two (2) 1/2” X 5/16”
X 5-3/4” square u-bolts over the spring clamp and spring.
Secure this spring to the axle assembly using a spring plate
and four (4) 1/2” flange lock nuts.

Install spring bracket bushing and 9/16” X 3-1/4” hex bolt into
rear frame spring shackle. Secure with 9/16” hex nut. Hook
leaf spring on axle assembly over bushing just installed.
Insert 9/16” X 3-1/4” hex bolt in eye of leaf spring and secure
into front frame spring shackle. Tighten all four bolts on both
sides on of trailer to secure the axle assembly to the under
carriage of the trailer.

Tires:

Remove stud thread protectors. Mount tires to hub using
1/2” lug nuts.

Caution:

1. To prevent damage to your utility trailer or
towing vehicle, tighten all fasteners before
towing.

2. Your utility trailer is equipped with a totally
grounded wire harness. You must be sure
the wire harness plug that comes from the
tow vehicle is grounded to the tow vehicle
using the white grounding wire.

3. Always secure (tie) your load down before
towing.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003618

Page 6 2/02/06