Shogun Motorsports CBR250R User Manual

CBR250R 11-12 NO CUT Frame Slider
Installation Instructions
Part Numbers: 750-3110, 750-3119, 710-3119,
850-3110C

MADE IN THE USA!
Carefully read instructions in their entirety before the install

Professional installation is recommended. Always use proper safety measures during the install of this
product. Do not try to install this product without proper tools, recently calibrated torque wrench,
correct torque specifications from factory service manual, safety goggles and gloves. The motorcycle
must be in a fixed secure position before the install process begins. DO NOT remove both engine studs
at the same time. Shogun is not responsible for any part of your motorcycle for any reason.

Replacement Parts List: Left Side Components (as if you were sitting on the bike)
QTY Price each Part Numbers Descriptions

1 $20.00 99-FS-750-3119-L Black Left Side Puck
1 $20.00 99-FS-750-3110-L White Left Side Puck
1 $30.00 99-FS-850-3110C-L Chrome Billet Left Side Puck
1 $45.00 99-FS-710-3119-L Carbon S5 Left Side Puck
1 $45.00 99-OF-750-3110-L Left Side Offset Black Anodized
1 $10.00 99-SP-750-3110 Puck Spacer Black Anodized
2 $2.50 428-9108 Left Side 25mm Offset Spacer
2 $1.50 99-HB-SH0610060 Socket Cap 6 X 1.00 X 60 (Offset Bolts)
1 $3.50 99-HB-SH10125060 Socket Cap 10 X 1.25 X 60 (Holds puck to offset)
1 $.50 99-HW-M10WASH 10mm Washer

Replacement Parts List: Right Side Components (as if you were sitting on the bike)
1 $20.00 99-FS-750-3119-R Black Right Side Puck
1 $20.00 99-FS-750-3110-R White Right Side Puck
1 $30.00 99-FS-850-3110C-R Chrome Billet Right Side Puck
1 $45.00 99-FS-710-3119-R Carbon S5 Right Side Puck
1 $45.00 99-OF-750-3110-R Right Side Offset Black Anodized
1 $10.00 99-SP-750-3110 Puck Spacer Black Anodized
1 $2.50 428-9106 Right Forward 24mm Offset Spacer
1 $2.50 428-9107 Right Rearward 22mm Offset Spacer
2 $1.50 99-HB-SH0610060 Socket Cap 6 X 1.00 X 60 (Offset Bolts)
1 $3.50 99-HB-SH10125060 Socket Cap 10 X 1.25 X 60 (Holds puck to offset)
1 $.50 99-HW-M10WASH 10mm Washer

Frame Sliders: Left and Right frame sliders are the same length.

Installation Steps:

Some photos in this section are used for illustration examples only.

1. Remove Left and Right mid panels to expose mounting locations and disconnect side marker

lights. Use caution not to break bodywork mounting tabs shown below.

2. Remove left main OEM engine stud (you will use later to mount offset) and the two 6mm case

bolts used for offset mounting location.

3. Before left side offset is installed pre assemble the offset using two 6 X 1.00 X 60 (99-HB-

SH0610060) socket cap bolts and two 25mm offset spacers (428-9108) with the larger diameter
part of the spacer towards the backside of the offset.