Shogun Motorsports 250 User Manual

Ninja 250 08-12 Frame Slider Installation
Instructions
Part Numbers: 750-4119, 755-4119, 750-4110,
850-4110

MADE IN THE USA!

Carefully read instructions in their entirety before the install.
Professional installation is recommended. Always use proper safety measures during the install of this
product. Do not try to install this product without proper tools, recently calibrated torque wrench,
correct torque specifications from factory service manual, safety goggles and gloves.The motorcycle
must be in a fixed secure position before the install process begins. DO NOT remove both engine studs
at the same time without a safe secure support under the engine. Shogun is not responsible for any part

of your motorcycle for any reason. Precisely measure location of cut and if in doubt at any point please

call us before the install process has begun.

Replacement Parts List: Left Side Components (as if you were sitting on the bike)
QTY Price each Part Numbers Descriptions

1 $20.00 99-FS-750-4119-L Black Left Side Puck
1 $20.00 99-FS-750-4119-L White Left Side Puck
1 $30.00 99-FS-850-4110-L Polished Billet Left Side Puck
1 $60.00 99-OF-750-4110-L Left Side Rail Black Powder Coat
1 $2.50 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 (Holds puck to offset)
2 $.15 99-HW-M10WASH Washer M10 Zinc Plated
1 $.50 99-LN-LN10125 Hex Lock Nut 10 X 1.25

Replacement Parts List: Right Side Components (as if you were sitting on the bike)
1 $20.00 99-FS-750-4119-R Black Right Side Puck
1 $20.00 99-FS-750-4119-R White Right Side Puck
1 $30.00 99-FS-850-4119-R Polished Billet Right Side Puck
1 $60.00 99-OF-750-4110-R Right Side Rail Black Powder Coat
1 $2.50 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 (Holds puck to offset)
2 $.15 ea 99-HW-M10WASH Washer M10 Zinc Plated
1 $.50 99-LN-LN10125 Hex Lock Nut 10 X 1.25

Replacement Parts List: Front and Rear Engine Studs (as if you were sitting on the bike)
1 $11.00 99-HR-TH3/8-16 x6 11/16-R 9/16 X 160 Welded Threaded Rod Rear
1 $11.00 99-HR-TH3/8-16x9 15/16-F 9/16 X 245 Welded Threaded Rod Front
2 $.50 ea 99-HN-LN3/8-16 9/16 X 18 Pitch Hex Flange Serrated Nut

Frame Sliders: Left Longer than Right

Installation Steps:

1. Some photos in this section are used for illustration examples only. It is up to you how you
decide to cut your motorcycles counter shaft cover to accept the frame slider rail,there are
different ways customers go through this process. Shogun is not responsible for any part of

your motorcycle for any reason. Precisely measure location of cut and if in doubt at any point

please call us before the install process has begun.Professional installation is recommended.
Always use proper safety measures during the install of this product. Do not try to install this
product without proper tools, recently calibrated torque wrench,safety goggles and gloves.

2. Remove left and right body panels. Unclip the turn signal connectors on each side.

3. Remove shift linkage from shift shaft and take counter shaft cover off.

4. Loosen front and rear engine through studs.Do not remove studs until after step 5.