Shiro DSL800ER User Manual
Web Interface User’s Guide
ADSL 2/2+ Ready 4 Port Ethernet Router
1. Introduction.......................................................................................................................................... 3
1.1 Features..................................................................................................................................... 3
2. Your gateway at a glance ................................................................................................................. 5
2.1 Ports and buttons...................................................................................................................... 5
2.2 LED description......................................................................................................................... 5
3. Installing your ADSL Router............................................................................................................. 6
4. Setting up your ADSL Router........................................................................................................... 7
4.1 Log into your ADSL Router..................................................................................................... 7
4.2 Quick Start................................................................................................................................. 8
4.3 Setup (for advance user)......................................................................................................... 9
4.3.1 Wide Area Network connection..................................................................................... 9
4.3.2 Local Area Network connection.................................................................................... 9
4.4 Configuring the WAN ............................................................................................................. 10
4.4.1 New Connection............................................................................................................ 10
4.4.2 Modify an Existing Connection.................................................................................... 17
4.4.3 Modem setup................................................................................................................. 17
4.5 Configuring the LAN............................................................................................................... 17
4.5.1 Enable/Disable DHCP.................................................................................................. 18
4.5.2 Changing the ADSL Router IP address..................................................................... 19
4.5.3 Firewall/NAT Services.................................................................................................. 20
4.6 Advanced (for advance user only) ....................................................................................... 21
4.6.1 UPnP............................................................................................................................... 21
4.6.2 Port Forwarding............................................................................................................. 22
4.6.3 Advanced Security........................................................................................................ 23
4.6.4 Access Control............................................................................................................... 24
4.6.5 LAN clients..................................................................................................................... 24
4.6.6 MAC Address Filters..................................................................................................... 24
4.6.7 Multicast.......................................................................................................................... 26
4.6.8 Static Routing................................................................................................................. 26
4.6.9 Dynamic Routing........................................................................................................... 27
4.7 Tools......................................................................................................................................... 28
4.7.1 System Commands....................................................................................................... 28
4.7.2 User Management......................................................................................................... 29
4.7.3 Update Firmware........................................................................................................... 29
4.7.4 Ping Test ........................................................................................................................ 30
4.7.5 Modem Test................................................................................................................... 30
4.8 Status........................................................................................................................................ 30
4.8.1 Network Statistics.......................................................................................................... 30
4.8.2 Connection Status......................................................................................................... 31
4.8.3 DHCP Clients................................................................................................................. 31
4.8.4 Modem Status................................................................................................................ 31
4.8.5 Product Information....................................................................................................... 31
4.8.6 System Log.................................................................................................................... 31
5. Appendix A: Troubleshooting......................................................................................................... 32
5.1 The ADSL Router is not functional....................................................................................... 32
5.2 I can’t connect to the ADSL Router...................................................................................... 32
5.3 The DSL Link LED continues to blink but does not go solid............................................ 33
5.4 The DSL Link LED is always off........................................................................................... 33
6. ADSL Router terms
.......................................................................................................................... 34
- 2 -
1. Introduction
The ADSL 2/2+ Ready 4 port Ethernet Router is the perfect high-speed WAN router. This fullfeatured product is specifically designed to connect to the Internet and directly connect to your
local area network via high speed 10/100 Mbps Ethernet
Targeted at the residential and SOHO users, it is the ideal solution to provide a 4 in 1 device for
both high speed broadband connectivity via a combined ADSL2/2+ ready Modem support,
Routing functionality for multi-user sharing, 4 port AutoMDI/MDIx 10/100 Switch and true Firewall
capability functionality.
This router also provides future proof functionality with higher data transmission rates with
ADSL2, ADSL2+, Extended Reach-ADSL support.
For game users, the ADSL Router had already pre configured for several low latency game ports.
Just click on the game you are playing on line and the rest is done for you
The ADSL Router is fully compatible with all PCs; as long as the PC supports an Ethernet
interface and is running a TCP/IP protocol stack, your PC can have high-speed WAN access.
So, plug in the ADSL Router (refer to easy start guide), configure it (per your ISP’s requirements)
and enjoy the fast Internet access like never before.
Security is provided via a double Stateful Packet Inspection and NAT based Firewall. VPN Passthrough and DMZ support provide additional security support for telecommuters as well as allow
flexibility while maintaining security against malicious hackers.
1.1 Features
ADSL/ATM Support
• ANSI T1.413 issue 2, ITU-T G.992.1 (G.dmt) and G.992.2 (G.lite) compliant
• ADSL2, ADSL2+, RE-ADSL compliant
• Rate Adaptive modem at 32 Kbps steps
• Dynamic Adaptive Equalisation to improve Carrier’s service area
• Bridge Tap Mitigation support
• ATM Layer with Traffic shaping QoS Support (UBR, CBR, VBR-rt, VBR-nrt)
• AAL ATM Attributes - AAL5
• Multiple PVC up to 8 support (Bridge Support)
• Spectral compatibility with POTS
• F5 OAM Loopback/Send and Receive
Encapsulation Support
• RFC2684 Bridge and Routed LLC and VC Mux support
• RFC2364 PPPoA Client support
• RFC2516 PPPoE Client support
• RFC2225/RFC1577 Classical IP Support
• Transparent Bridge Support
• PAP/CHAP/MS-CHAP for Password Authenication Support
- 3 -
Network Support
• Static IP, Dynamic RIP routing support
• IP/TCP/UDP/ICMP/ARP/RARP Application Support
• Network Address Translation (NAT)
• Port Mapping/Forwarding
• Easy setup of Port Forwarding rules for popular Games/Application
• NAT Application Level Gateway for popular applications
• DHCP Server/Relay/client
• DNS Relay Agent
• DMZ support
• Single Session IP Sec and PPTP/L2TP VPN pass through support
• PPP Always on with configurable timeout
• PPP Dial on Demand
• Universal Plug and Play Support
Management Support
• Web Based HTTP management GUI
• TFTP/FTP Support for Firmware Upgrade
• Web Based Firmware Upgrade (Local)
• Soft Factory Reset Button via Web GUI
• Diagnostic Test (DSL, OAM, Network, Ping Test)
• Telnet/CLI (Read Only)
• Syslog Support
• Firmware upgrade-able for future feature enhancement.
Security Support
• NAT for basic Firewall support
• Packet Filtering Firewall Support
• Stateful Packet Inspection Support
• Protection against Denial of Service attacks
• Password Authentication to Modem
External Connectors:
• 1 x RJ-11 Telephone socket for ADSL line
• 4 x RJ45 for 10/100Base-T Ethernet (MDI-X)
• 1 x DC Jack for Power Input
• 1 x Factory Default Reset Button
- 4 -
2. Your gateway at a glance
The 4 port Ethernet Router may have different ports and LEDs. Let’s take a look at the different
options. Depending upon your model, it may have some or all of the features listed below
2.1 Ports and buttons
Reset and Restore to Factory Defaults: The restore to factory defaults feature will set the
ADSL Router to its factory default configuration by resetting the ADSL Router. You may need to
place the ADSL Router into its factory defaults if the configuration is changed, you loose the
ability to interface to the ADSL Router via the web interface, or following a software upgrade,. To
reset the ADSL Router, simply press the reset button for about ~ 10 seconds. The ADSL Router
will be reset to its factory defaults and after about 30 ~ 40 seconds the ADSL Router will become
operational again.
LAN (local area network) port(s): There are 4 Ethernet available for connection to four network
devices. If 4 ports are insufficient, you can also one of the port to a hub/switch. Depending on the
connection, you may need a cross over cable or a straight through cable.
Power is where you connect the power. Make sure to observe the proper power requirements.
The require power is 9 volts.
DSL port: This is the WAN interface that connects directly to your phone line.
2.2 LED description
1. POWER
Lights up when power is supplied to the ADSL Router.
2. ETH/ACT ( E1- E4 )
Lights up when the Ethernet cable is properly connected from your ADSL Router to the
Ethernet Card.
Flickers when the ADSL is transmitting/receiving data.
3. DSL
Lights up when the DSL connection is established.
Flickers when the ADSL Router is trying to establish a connection with the ADSL
Service Provider. (Training mode)
4. Internet
Lights up when the PPP connection is established.
- 5 -
3. Installing your ADSL Router
1. Locate an optimum location for the ADSL Router.
2. For connections to the Ethernet and DSL interfaces, please refer to the easy start guide.
3. Connect the AC Power Adapter provided. Depending upon the type of network, you may want
to put the power supply on an uninterruptible supply. Only use the power adapter supplied with
the ADSL Router. A different adapter may damage the product.
Now that the hardware installation is complete, proceed to Chapter 4: Setting up your ADSL
Router
Up to 4 PCs Connections
ADSL
Computers or Notebooks with
Ethernet N et work Cards
- 6 -
4. Setting up your ADSL Router
This section will guide you through your ADSL Router’s configuration. The ADSL Router is
shipped with a standard PPP configuration.
4.1 Log into your ADSL Router
To configure your ADSL Router, open your web browser. You may get an error message at this
point; this is normal. Do not panic!. Continue following these directions. Type the default IP
address (192.168.1.1) Press the Enter key and the following screen, shown in Figure 1 will
appear. The default user name is admin (case sensitive) and the password is admin (case
sensitive).
Note: Before setting up your ADSL Router, make sure you have followed the easy start
guide. You should have your computers configured for DHCP mode and have proxies
disabled on your browser. Also if you access the ADSL Router, and instead of getting a
login screen, the browser instead displays a login redirection screen, you should check
your browser's setting, and verify that JavaScript support is enabled. Also, if you do not
get the screen shown in Figure 1, you may need to delete your temporary Internet files
(basically flush the cached web pages).
Figure 1 (Log-in screen)
- 7 -
4.2 Quick Start
The first screen (Figure 2) that appears (after the log in screen) is the Quick Start screen. By
default the ADSL Router has being configured to PPP connection and user would only need to
enter the username and password (as specified by the local ISP) to make connection to the
Internet.
The Quick Start page is meant for basic users whom only require easy and seamless connectivity
to the Internet without worrying about any other advance configuration setting.
Important:
After clicking on Connect, please be sure to “Save Settings” to register the username / password
or any other changes.
- 8 -
Figure 2 (Quick Start page)
4.3 Setup (for advance user)
From this screen the user can setup the ADSL Router (configure the LAN and WAN
connection(s), configure the advanced configuration options within the ADSL Router (security,
routing, and filtering), access tools that are helpful for debug purposes, obtain the status of the
modem, and view the extensive online help.
To setup your ADSL Router with a basic configuration, select Setup. Figure 3 illustrates the
setup page. The page is broken into two subsections the WAN configuration and the LAN
configuration.
Before configuring the ADSL Router, there are several concepts that you should be familiar with
on how your new ADSL Router works. Please take a moment to familiarize yourself with these
concepts, as it should make the configuration much easier.
4.3.1 Wide Area Network connection
On the other side of the ADSL Router is where your Wide Area Network (WAN) connection; also
referred to as a broadband connection. This WAN connection is different for every WAN supplier.
Most of the configuration you will perform will be in this area. Local Area Network Connection(s)
4.3.2 Local Area Network connection
On one side of your ADSL Router, you have your own Local Area network (LAN) connections.
This is where you plug in your local computers to the ADSL Router. The ADSL Router is normally
configured to automatically provide all the PC's on your network with Internet addresses.
- 9 -
Figure 3 (Setup page)
4.4 Configuring the WAN
Before the gateway will pass any data between the LAN interface(s) and the WAN interface, the
WAN side of the modem must be configured. Depending upon your DSL service provider or your
ISP, you will need some (or all) of the information outlined below before you can properly
configure the WAN:
• Your DSL line VPI and VCI
• Your DSL encapsulation type and multiplexing
• Your DSL training mode (default is MMODE)
• For PPPoA or PPPoE users, you also need these values from your ISP:
• Your username and password
• For RFC 1483 users, you may need these values from your ISP:
• Your DSL fixed Internet IP address
• Your Subnet Mask
• Your Default Gateway
• Your primary DNS IP address
Since multiple users can use the ADSL Router, the ADSL router can simultaneously support
multiple connection types; hence, the user must set up different profiles for each connection. The
ADSL Router supports the following protocols:
• DHCP
• RFC2364 / PPPoA
• RFC2516 / PPPoE
• Static
• Bridged
• RFC1577 / CLIP
.
4.4.1 New Connection
A new connection is basically a virtual connection. Your ADSL Router can support up to 8
different (unique) virtual connections. If you have multiple different virtual connections, you may
need to utilize the static and dynamic routing capabilities of the modem to pass data correctly.
4.4.1.1 Bridged gateway profile and Connection
A pure bridged connection does not assign and IP address to the WAN interface. NAT and
firewall rules are not enabled. This connection method makes the ADSL Router act as a hub,
and just passes packets across the WAN interface to the LAN interface.
To configure the ADSL Router as a bridge, click on Setup and then click on New Connection. The
default PPPoE connection setup is displayed. At the Type field select Bridge and the Bridge
connection setup page is displayed (see Figure 4). Give your Bridge connection a unique name;
the name must not have spaces and cannot begin with numbers. In this case the unique name is
called Bridge. Select the encapsulation type (LLC or VC); if you are not sure just use the default
mode. Select the VPI and VCI settings; your DSL service provider or your ISP will supply these;
in this case the DSL service provider is using 0,100. Also select the quality of service (QOS);
leave the default value if you are unsure or the ISP did not provide this information.
- 10 -
Figure 4 (Bridge Connection Setup)
To complete the connection you must now click the apply button. The apply button will
temporarily save this connection. To make the change permanent, you need to click on Save
Settings. At the system commands page, click on Save All.
4.4.1.2 PPPoA Connection Setup
PPPoA is also known as RFC 2364. It is a method of encapsulating PPP packets over ATM cells
which are carried over the DSL line. PPP or Point-to-Point protocol is a method of establishing a
network connection / session between network hosts. It usually provides a mechanism of
authenticating users. LLC and VC are two different methods of encapsulating the PPP packet.
Contact your ISP to make sure which encapsulation is being supported.
By selecting PPPoA, you are forcing your ADSL Router to terminate the PPPoA connection. The
advantage is that the PPPoA termination is done within the ADSL Router and not on your PC; this
frees up your PC resources and allows multiple users to utilize the PPPoA connection.
To configure the gateway for PPPoA, click on Setup and then click on New Connection. The
default PPPoE connection setup is displayed. At the Type field select PPPoA and the PPPoA
connection setup page is displayed; figure 5 illustrates a typical PPPoA configuration. Give your
PPPoA connection a unique name; the name must not have spaces and cannot begin with
numbers. In this case the unique name is called PPPoA1. Select the encapsulation type (LLC or
VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL
service provider or your ISP will supply these; in this case the DSL service provider is using
0,100. Also select the quality of service (QOS); leave the default value if you are unsure or the
ISP did not provide this information.
- 11 -
Loading...