Shinybow USA SB-6800T, SB-6800R Instruction Manual

SB-6800T

SB-6800T/SB-6800R

HDMI OVER IP Transmitter & Receiver

SB-6800R

INSTRUCTION MANUAL

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal

ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to

qualied service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.

19. Service Information Equipment should be serviced by qualied service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS

HDMI Over IP 100M Extender Series

Thank you for purchasing the SB-6800T/R HDMI Over Channel IP Transmitter and Receiver. You will nd this

unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting
to use extender.

CONTENTS

INTRODUCTION ..............................................................1

FEATURES ....................................................................... 2

SPECIFICATIONS ............................................................ 3

TRANSMITTER

FRONT PANEL ............................................................. 4

BACK PANEL ............................................................... 5

RECEIVER

FRONT PANEL ............................................................. 6

BACK PANEL ............................................................... 7

TRANSMITTER IR PIN CONFIGURATION ...................... 8

IP RECEIVER IR PIN CONFIGURATION ........................ 9

IP TRANSMITTER RS-232 PIN CONFIGURATION ........10

IP RECEIVER RS-232 PIN CONFIGURATION .............. 11

TYPICAL APPLICATION ................................................12

WALL MOUNT APPLICATIONS .....................................13

19 INCH RACK MOUNT APPLICATIONS .....................14

INTRODUCTION

The SB-6800 series provides HDMI 1.3a IR remote and RS-232
signal all over IP using a single CAT cable along with a standard
network switch. The gigabit switch requires either a separate sub­net from your traditional LAN or a dedicated switch. The SB-6800
series uses IGMP and 8K jumbo frame packets gigabit switch
hub to distribute up to 328 feet (100M). The SB-6800 uses a
single UTP/FTP CAT6, CAT6a or CAT7 cable via a RJ-45 8P8C
female socket (supports 568a/b). The SB-6800 provides full HD
HDMI 1.3a resolutions of 480i/p, 720p,1080i/p format quality that
are identical to the source with no signal degradation or delay.
The Transmitter is useful for sending 1080p HDMI digital video /
multi-channel digital audio. IR remote and RS-232 are available
to control a source between Transmitter and Receiver. Control
signals via single category cable to transmit the signals from
Transmitter to the Receiver.

PACKAGE CONTENTS

Check that you have the following components;

• SB-6800 Transmitter or Receiver IP Extender console

• 1 inch High Wall mount pack (Part # WM-1INCH-L80MM)

• RS-232 & F/W Update cable (Part # MiniUSB-DB9p-20cm)

• Instruction Manual

• AC Adaptor : 12VDC/2A (universal power switch

50/60Hz,100~240VAC input)

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts
inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.

We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.

We reserve the right to make improvements to this document
and/or product at any time and without notice.

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means

— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent

© Copyright 2015. All Rights Reserved.
Version 1.3 SEPT 2015
6800TR-20150526-005

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.

1

FEATURES & OPTIONAL ACCESSORIES

FEATURES

• HDMI signal extended over IP (Requires LAN switch with IGMP function and 8K jumbo frame packets), use CATx (UTP/STP)
category cable up to 320 feet (100M)

• HDMI 1080p@60 video, Compatible with HDMI 1.3 and HDCP compliant

• TCP/IP feature set over a single LAN cable. Transmits HDMI, IR(CIR) and RS-232 I/O

• Link speeds of up to 1080p / TMDS format Max. 2.25 Gbit/s, Signal up to 148MHz

• Deep Color, Full HD 1080p@60Hz/@24 bit pixels. Blu-rays at 24/30 FPS

• Extends 1080p for long distances, up to 320 feet (100M)

• Transmits Digital Audio PCM 2-CH

• IP Transmitter supports a total of (5) units to IGMP HUB. Channels 001~064

• IP Receiver supports a total of (64) units, Select TX Channels 001~064

• Transfer controls IR signal together with the HDMI signal

• IP Transmitter supports 1x HDMI loopout to preview HDMI source signal

• Uses a single category cable to transmit HDMI, RS-232 and IR control signals simultaneously

• Simply set up the Transmitter and Receiver to the same channel and all settings are automatically congured

• Point to Point or point to multipoint or multipoint to multipoint congurations

• HDMI CEC between your connected source and display gear

• LED indicators to show the POWER/LINK status

• Mounting wall mount pack supplied, surface mounting bracket included

OPTIONAL ACCESSORIES :

• SB-100 set (IR Receiver Extender assy plug)

• SB-100C cable (IR Receiver Cable)

• SB-101 set (IR Transmitter Extender assy plug)

• SB-101C cable (IR Transmitter Cable)

2

SPECIFICATIONS

SPECIFICATIONS

• Type of Extender: HDMI over IP Extender via a single LAN category UTP/STP cable

• Transmit Signals: HDMI Video/Audio, RS-232 i/o, RX: IR input / TX: IR output

• HDMl Support: HDMI 1.3 HDMI format standard, DVI and HDCP compliant

• HDCP Support: HDCP 1.X, 1.4 compliant

• Video Support: HDMI formats up to 1080p@60Hz@48b/pixel (1920x1080) resolution

• Video Bandwidth: 2.25Gbps (225MHz)

• Audio I/O Supports: Dolby Digital (PCM-2CH)

• Repeater LAN HUB: Network Switch or Network Router with IGMP function

• Network Switch Linkage: IP Transmitter supports a total of (5) units and IP Receiver supports a total of (64) units (328 ft/100M)

• Supports HDMI Resolutions: 480p, 720p 1080i/1080p resolutions

• IR Infrared Frequency: 38Khz

• Category Cable Support: CAT6, CAT6a, CAT7 UTP/STP cable

• Scan Rate Accepted: Supports HDMI full HD Resolution; Frequency 24Hz to 60Hz

• Transfer Distance: Up to 2.25Ghz/148.5Mhz (328 ft/100M)/1080p

• Controls: Transmitter: 1x IR out, 1x RS-232 I/O series interface / Receiver: 1x IR in, 1x RS-232 I/O series interface

• IP Channel Support: Transmitter: CH-001 ~ CH-064 / Receiver: CH-001 ~ CH-064

• Select Transfer: 240: (2400), 480: (4800), 960: (9600), 192: (19200), 288: (28800)

• RS-232 Baud Rate: 384: (38400), 576: (57600), 115: (115200)

• HDMI I/O Connectors: HDMI Type A - SMD 19pin Female Type

• IP Extender Connectors: RJ-45, 8p8c Female socket

• Transfer RS-232 Connector: Terminal Black 3 pin

• Transfer IR Connector: OD3.5mm Female Jack

• Transfer Distance: up to 328 ft (100M) Tx to Rx unit and 1640 ft (500M) LAN Switch-to-LAN Switch

• Temperature: Operating Temperature 32°F-100°F (0°C-38°C)

• Chassis Material: Metal (think 1mm)

• Color: Black

• Dimensions (LxWxH): 5.31 x 5.11 x 1 in (135x130x26 mm)

• Rack Mount (19 inch):

• #1U high 19 inch 1x Unit

• #1U high 19 inch install 2x Unit

• #2U high 19 inch install 4x Unit

• #4U high 19 inch install total 10 pcs Rack mountable

• Shipping Weight (net): Transmitter: 0.650 kgs / 1.43 lb / Receiver: 0.4175 kgs / 0.9125 lb

• Safety Approvals: CE, FCC & REACH

• Power Consumption: Transmitter: Full load Max. 1200mA (12VDC, 6W) / Receiver: Full load Max. 2000mA (12VDC, 6W)

• Transmitter Power Supply: Power Input +12VDC, 2A (Universal Type 50/60Hz, 100~240 VAC)

• Receiver Power Supply: Extra Power Input +12VDC, 2A (Universal Type 50/60Hz, 100~240 VAC)

As product improvements are continuous, specications are subject to change and without notice.

3

TRANSMITTER FRONT PANEL

FRONT PANEL

1. POWER LED DISPLAY: The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and

is receiving power. The extender will remember that last state during a power cycle. When power is removed and resorted, the last

conguration will be evoked.

2. LINK LED DISPLAY: IP Extender link status via LED illuminates blue to indicate that a IP Extender is present on that input.

3. IP CHANNEL SETTING ENABLED LED DISPLAY: Select setting IP Channel status via LED show out.

4. RS-232 SETTINGS ENABLED LED DISPLAY: Select setting RS-232 baud rate status via LED show out.

5. RESET: Reset the SB-6800T back to factory defaults.

6. SELECT BUTTON: Select IP Channel or RS-232 Baud Rate button.

7. IP CHANNEL: IP Channel or RS-232 baud rate status via LCM show out.

8./9. IP CHANNEL and RS-232 UP/DOWN: Select IP Channel or RS-232 Buad Rate.

10. LOCK: Press and hold LOCK button for 3 seconds to lockout the front panel. Press and hold LOCK button for 3 seconds to enable the

front panel.

11. ENTER: Press ENTER to conrm entries.

12. IR SENSOR: The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.

4

TRANSMITTER BACK PANEL

BACK PANEL

1. POWER DC INPUT: DC12V, 2A, (F-connector Male Plug).

2. LAN: (Transmitter output) Sends HDMI source signal to the

Receiver via RJ-45 connector.

3. IR OUTPUT: Receives Bi-directional IR signal from the IP

Receiver to Control source device.

4. RS-232 I/O: Sends RS-232 via HDBaseT

™

CATx cable.

5. IR ExTERNAL PORT: Uses the IR remote to control the IP Transmitter.

6. FIRMWARE UPDATE: Console rmware update port.

7. HDMI LOOP OUTPUT: HDMI loop output.

8. HDMI INPUT: HDMI signal Input.

5

RECEIVER FRONT PANEL

FRONT PANEL

1. POWER LED DISPLAY: The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and

is receiving power. The extender will remember that last state during a power cycle. When power is removed and resorted, the last

conguration will be evoked.

2. LINK LED DISPLAY: IP extender link status via LED illuminates blue to indicate that a IP extender is present on that input.

3. IP CHANNEL SETTING ENABLED LED DISPLAY: Select setting IP channel status via LED show out.

4. RS-232 SETTINGS ENABLED LED DISPLAY: Select setting RS-232 baud rate status via LED show out.

5. RESET: Reset the SB-6800R back to factory defaults.

6. SELECT BUTTON: Select IP Channel or RS-232 baud rate button.

7. IP CHANNEL: IP channel or RS-232 baud rate status via LCM show out.

8./9. IP CHANNEL and RS-232 UP/DOWN: Select IP channel or RS-232 buad rate.

10. LOCK: Press and hold LOCK button for 3 seconds to lockout the front panel. Press and hold LOCK button for 3 seconds to enable the

front panel.

11. ENTER: Press ENTER to conrm entries.

12. IR SENSOR: The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.

6

RECEIVER BACK PANEL

BACK PANEL

11. POWER DC INPUT: DC12V, 2A, (F-connector male plug).

2. LAN: (Transmitter output) Send HDMI source signals to the

Receiver via RJ-45 connector.

3. HDMI OUTPUT: HDMI signal output, signal from source device.

4. IR INPUT: Transmit Bi-directional IR signal to IP Transmitter to

control source device.

5. RS-232 I/O: Sends RS-232 via HDBaseT

6. IR ExTERNAL PORT: Use IR remote to control the IP Transmitter.

7. FIRMWARE UPDATE: Console rmware update port.

™

CATx cable.

7

TRANSMITTER IR PIN CONFIGURATION

PIN CONFIGURATION:

SB-101 and SB-101C Transmitter Pin configuration

1. SB-101 IR 300M Transmitter

Device Cable (3C) IR Transmitter (SB-101)

SB-101

IR Transmitter Set

RoHS/95/EC

DC 12V

IR out

From

Receiver

IR in

To

Receiver

CAT6/6a/7

OUTPUT

SB-101 Maximum Distance ~ 984 feet (300M)

SB-101

IR Tx

SB-101C

Transmitter Cable

IR Transmitter cable 6ft (2M)

SB-101C Maximum Distance ~ 6 feet (2M)

RoHS/95/EC

DC 12V

IR out

From

Receiver

IR in

To

Receiver

CAT6/6a/7

OUTPUT

SB-101C

IR Tx

*** When you plug the External IR extender into the switcher, the front panel IR transmitter remains active. ***

2. SB-101C IR 2M Transmitter

Device Cable (3C) IR Transmitter (SB-101C)

IP TRANSMITTER FRONT PANEL IR OUT & IR ExTERNAL PORT

Note: When you plug the External IR extender into the switcher, the front panel IR receiver remains active.

PincongurationforIR984feet(300M)ExtenderTransmittersuchasSB-101compatible

Tip: Signal
Ring :VCC
Sleeve: GND

Tip

Ring

Ring

Sleeve

VCC (Ring)

GND (Sleeve)

SB-101

IR Transmitter Set

     IRRX-100ReceiverandIRTX-101TransmitterTheDISTANCEmaximum~984feet(300M)

IR Transmitter cable 6ft (2M)

Tip: Signal
Ring: NC
Sleeve: GND

SB-101C

Transmitter Cable

     IRRX-100CReceiverCableandIRTX-101CTransmitterCableTheDISTANCEmaximum6feet(2M)

Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.

Tip

Sleeve

Ring

Sleeve

Tip (center)

Ring

Tip (center)

8

Signal (center)

SB-101 Maximum Distance ~ 984 feet (300M)

Sleeve

GND (Sleeve)

Signal (center)

SB-101C Maximum Distance ~ 6 feet (2M)

IP RECEIVER IR PIN CONFIGURATION

).

*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***

SB-100

IR Receiver Set

IR Receiver cable 6ft (2M)

SB-100C

IR Receiver Cable

1. SB-100 IR 300M Receiver

Switcher IR EXT. In Cable (3C) IR Receiver (SB-100)

2. SB-100C IR 2M Receiver

Switcher IR EXT. In

Cable (2C) IR Receiver (SB-100C)

The SB-100 IR Receiver is required when using the port “ALL in” Jack.

The SB-100C IR Receiver will not function on the port “ALL in” Jack.

SB-100C Maximum Distance ~ 6 feet (2M)

INPUT

DC 12V

RoHS/95/EC

IR EXT .

RS-232

RS-232 IR EXT. in

ANI-100

IR Rx

P

O

W

ER

IN

PU

T

-

1

1 2 3

4

1 2

3

4

1

2 3

4

1 2 3

4

H

DM

I MAT

R

IX

SWIT

C

H

ER

O

N

O

F

F

IN

P

U

T -2

I

N

P

UT

-3

I

N

P

U

T

-

4

S

W

IR

Distance: Max.(2M)

IR PN#: SB-XXXX

Control Switch SB-XXXX

INPUT

DC 12V

RoHS/95/EC

IR EXT .

RS-232

RS-232 IR EXT. in

ANI-100

IR Rx

P

O

W

ER

IN

PUT

-1

1

2 3 4

1 2

3 4

1

2 3

4

1

2 3

4

H

DM

I MAT

R

IX

S

WIT

CH

ER

O

N

O

F

F

IN

P

U

T -2

I

N

P

UT

-3

IN

P

U

T

-

4

SW

IR

Distance: Max.300M

IR PN#: SB-XXXX

Control Switch SB-XXXX

SB-100 Maximum Distance ~ 984 feet (300M)

IP REVEIVER REAR PANEL IR IN & IR ExTERNAL PORT

Note: When you plug the External IR extender into the switcher, the front panel IR receiver remains active.

Pin configuration for IR 984 feet (300M) Extender Receiver such as SB-100 compatible

PincongurationforIR984feet(300meters)ExtenderReceiversuchasSB-100compatible

VCC (Ring)

Tip: Signal
Ring :VCC
Sleeve: GND

Tip

Ring

Ring

Sleeve

GND (Sleeve)

SB-100

     IRRX-100ReceiverandIRTX-101TransmitterTheDISTANCEmaximum~984feet(300M)

Pin configuration for IR Receiver 6 feet (2M) cable such as SB-100C compatible

PincongurationforIRReceiver6feet(2meters)cablesuchasSB-100Ccompatible

IR Receiver Set

SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)

IR Receiver cable 6ft (2M)

Tip: Signal
Ring: NC
Sleeve: GND

SB-100C

     IRRX-100CReceiverCableandIRTX-101CTransmitterCableTheDISTANCEmaximum6feet(2M)

IR Receiver Cable

SB-100 Receiver and SB-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)

Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.

Tip

Sleeve

Ring

Sleeve

Tip (center)

Ring

Tip (center)

9

Signal (center)

Sleeve

GND (Sleeve)

Signal (center)

IP TRANSMITTER RS-232 PIN CONFIGURATION

IP TRANSMITTER ExTENDER RS-232 PIN CONFIGURATION

RS-232 cable is a straight thru cable and not null-modem

Denition Pin Pin Denition

1 1 DCD

TX 2 2 RX

RX 3 3 TX

4 4 DTR

GND 5 5 GND

6 6 DSR

7 7 RTS

8 8 CTS

9 9 RI

IP TRANSMITTER ExTENDER FIRMWARE UPDATE (MINI USB-B FEMALE 5 PIN) SOCKET PIN CONFIGURATION

Connector mini USB-B female 5pin socket pin conguration

10

IP RECEIVER RS-232 PIN CONFIGURATION

IP RECEIVER ExTENDER RS-232 PIN CONFIGURATION

RS-232 cable is a straight thru cable and not null-modem

Denition Pin Pin Denition

1 1 DCD

TX 2 2 RX

RX 3 3 TX

4 4 DTR

GND 5 5 GND

6 6 DSR

7 7 RTS

8 8 CTS

9 9 RI

IP RECEIVER ExTENDER FIRMWARE UPDATE (MINI USB-B FEMALE 5PIN SOCKET) PIN CONFIGURATION

Connector mini USB-B female 5pin socket pin conguration

11

TYPICAL APPLICATION

INSTALLING DIAGRAM

Samples Connection:

1. Using IP Receiver to receive the HDMI signals and control IR return channel

IR input and RS-232 I/O.

2. The distance 100 meters between IP Transmitter or network switch and IP

receiver.

3. Using the category cable (CAT6, CAT6a).

Samples Connection:

1. Using IP Transmitter to extend the HDMI signals, control the IR return

channel IR output and RS-232 I/O.

12

2. The distance 100 meters between IP Transmitter or network switch and IP

receiver.

3. Using the category cable (CAT6, CAT6a).

WALL MOUNT APPLICATIONS

WALL MOUNT: (OPTIONAL)

SB-6800T/SB-6800R:Wallmountaccessories

Model No. : #WM-1INCH-L210MM

Parts No.: MEER6300ER11000

Install Application: SB-6800T/SB-6800R WALL MOUNT

Application Diagram : #1inch HIGH - 1x Unit (HL=27x80mm)

13

19 INCH RACK MOUNT APPLICATIONS

1U RACK MOUNT: (OPTIONAL)

SB-6075A:Complete19inch1U-1unitrackmount

Install Application : SB-6800T/SB-6800R 19 INCH 1U-01P RACK MOUNT

Parts No.: MEER63000013000

Model No. : #1U-01p-L210MM-COV Application Diagram : #1U 19 inch - 1xUnit (HL=27x210mm)

SB-6800T/SB-6800R 1U ear mount pairs

Parts No.: MEER6300ER1102

SB-6075B:Complete19inch1U-2unitsrackmount

Install Application : SB-6800T/SB-6800R 19 INCH 1U-02P RACK MOUNT

Parts No.: MEER63000013000

Model No. : #1U-01p-L210MM-COV Application Diagram : #1U 19 inch - 2xUnit (HL=27x210mm)

SB-6800T/SB-6800R 1U ear mount pairs

Parts No.: MEER6300ER1102

14

19 INCH RACK MOUNT APPLICATIONS

2U RACK MOUNT: (OPTIONAL)

SB-6002:Complete19inch2U-4unitsrackmount

Install Application : SB-6800T/SB-6800R 19 INCH 2U-04P RACK MOUNT

Parts No.: MEER6802FT13000

Model No. : #2U-04p-L210MM-COV Application Diagram: #2U 19 inch - 4xUnits (HL=27x210mm)

SB-6800T/SB-6800R 1U ear mount pairs

Parts No.: MEER6300ER1102

4U RACK MOUNT: (OPTIONAL)

SB-6069:Complete19inch4U-10unitsrackmount

Install Application: SB-6800T/SB-6800R 19 INCH 4U-10P RACK MOUNT

Parts No.: MEER6078001300

Model No. : #4U-10p-L210MM-COV Application Diagram : #4U 19 inch - 10xUnit (HL=27x210mm)

SB-6800T/SB-6800R 4U ear mount pairs

Parts No.: MEER6074ER11000

Model No. : #5U-10p-L210MM-EAR

SB-6800T/SB-6800R 4U rack mount ear pairs

Parts No.: MEER1616HA10000

15

LIMITED WARRANTY

PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.

RESTRICTIONS ON USE OF THE PRODUCT

It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.

The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product

are licensed to you by SHINYBOWUSA, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “SHINYBOWUSA”) for your

personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.

The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.

The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its ofces within the State of Texas, United States of America. SHINYBOWUSA

makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.

DISCLAIMERS AND LIMITATION OF LIABILITY

SHINYBOWUSA may change or modify the Product at any time, from time to time.

THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.

SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.

TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BY SHINYBOWUSA.

UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.

END OF DOCUMENT

16

THIS PAGE IS INTENTIONALLY LEFT BLANK.

122 Rose Ln. Suite 303

1-877-SHINY-USA
1-877-744-6987
1-972-377-2508

[e-mail]

|

Frisco, Texas 75034

www.shinybowusa.com