Shinybow USA SB-6355 Instruction Manual

Download

SB-6355 KIT

HDMI HDBaseT™ 4K/UHD Tx & Rx Extender KIT up to 330 Feet (100M)

(PoH, Dual LAN, 2-way IR, RS-232, SPDIF, Analog Audio, HDMI)

RECEIVER

TRANSMITTER

INSTRUCTION MANUAL

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal

ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to

qualied service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.

19. Service Information Equipment should be serviced by qualier service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS

HDBaseT™ with PoH 100M EXTENDER Series

Thank you for purchasing the SB-6355x Kit HDBaseT™ with PoH Transmitter and Receiver. You will nd this unit easy to

install and highly reliable but it is essential that you read this manual thoroughly before attempting to use the converter.

CONTENTS

INTRODUCTION ..............................................................1

FEATURES & CONTENTS ................................................ 2

SPECIFICATIONS ........................................................... 3

TRANSMITTER PANELS ................................................ 4

RECEIVER PANELS ....................................................... 6

IR PIN CONFIGURATION ............................................... 8

RS-232 PIN CONFIGURATION ...................................... 10

TYPICAL HDBaseT™ APPLICATION ........................... 12

RACK MOUNTS (OPTIONAL) ....................................... 13

WALL MOUNT APPLICATIONS .................................... 15

INTRODUCTION

Congratulations on your purchase of one of the most innovative HDMI 1.4a over single category cable HDBaseT™ Transmitter/ Receiver with POH (Power Over HDBaseT™) on the market today. SB-6355T HDBaseT™ Transmitter can transmit the HDMI, Ethernet, PoE with power (48VDC), IR Remote signals input to Receiver or output to destination and the RS-232 interface signal I/O to HDBaseT™ Receiver SB-6355R via single LAN (category) cable for the long distance Maximum 328 feet (100M). Transmitter use the single UTP/FTP (category cable) CAT6, CAT6a or CAT7 via RJ-45 8P8C female socket (Support 568a/b). This product provide higher full HD HDMI 1.4a, Resolution supports 480i/p, 720p,1080i/p or High full 4K2K-30Hz/24bpp, 4K2K-60Hz/24bpp

with 4:2:0 pixel fromet quality that are identical to the source high

quality full HDMI 1.4 signals. The Transmitter is useful for sending the 4K2K HDMI digital Video / multi-channel digital audio format, IR remote in or out, Ethernet, RS-232 in-out, KVM (USB2.0) and 48VDC power over HDBaseT™ (PoH) to HDBaseT™ Receiver. Controls signals via Single category cable transmit to the HDBaseT™ Transmitter and HDBaseT™ Receiver.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.

We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.

We reserve the right to make improvements to this document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means

— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without express written permission and consent

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

FEATURES & CONTENTS

FEATURES

• HDBaseT™ HDMI / DVI extender over CATX (UTP/STP) cable

• Compatible with HDMI 2.0 and HDCP 1.x, 2.2 complient

• Supports 5play feature set over a single LAN cable. Transmits HDMI, Digital Audio, Bi-directional IR(CIR), 100Base-Tx Ethernet,

USB 2.0, RS-232 I/O, SPDIF I/O and 13W PoH

• Application NxK AV matrixes, AV receivers, HD projectors, Single wire Tvs and Two-box Tvx, KVM (Keyboard, Video, Mouse) extension, digital signage display

• HDMI 1080p@60 video V1.4a 3D and Ultra HD 4K2K video, CEC / HDCP compliant

• Supports link speeds of up to Video, TMDS format Max. 10.2 Gbit/s, Signal 340MHz Deep Color, Full HD 1080p@60Hz@24/36/48bit/pixels

• Supports 1080p TV’s at 24/30/60/100/200/240 Hz and above as well as Blu-rays at 24 FPS

• Supports Digital Audio 7.1 LPCM 192KHz, 24bits, Full HD Dolby TrueHD and DTS-HD Master

• Audio uncompressed HD audio formats

• Transfer Bi-directional Infrared control signal together with the HDMI signal

• Supports HDMI CEC between your connected Source and display gear

• With LED indicators to show the POWER/POE/LINK/HDCP status

• Support external Bi-Directional SPDIF in/out and available for multichannel audio

• Support stereo audio I/O with PCM 2CH

• Support Super Audio CD (DSD), CEC commands protocol table

• Extend long distance 4K2K 340MHz/328 feet(100 Meters) or 1080p 148.5MHz/429 feet(150 M)

• Surface Mounting bracket included, Other mounting brackets available as a separate option

• Power Input Tx & Rx 48VDC(12.48W), Rx 12VDC(4.8W) with Low power consumes (4K load 500mA)

• Power supply using universal power switch 50/60Hz,100~240VAC

PACKAGE CONTENTS

Check that you have the following components;

• SB-6355x HDBaseT™ Extender console

• SB-100 set (IR Receiver Extender assy plug)

• SB-100C cable (IR Receiver Cable)

• SB-101 set (IR Transmitter Extender assy plug)

• SB-101C cable (IR Transmitter Cable)

• 1 inch High Wall mount pack (Part # WM-1INCH-L210MM)

• Users Guide

• AC Adaptor :

• Transmitter: 48VDC/1A (universal power switch 50/60Hz,100~240VAC)

• Receiver: 12VDC/1A (universal power switch 50/60Hz,100~240VAC)

Optional Accessories :

• CAT6 Category cable distance 328 feet (100Meter), (P/N: UTP6-100)

SPECIFICATIONS

• Type of Extender: HDBaseT™ 5play set over a single LAN category UTP/STP Cable

• Transmit Signals: HD Video/Audio, 100Base-TX Ethernet, USB (KVM), SPDIF input, SPDIF output, RS-232 i/o, IR input, IR output

and PoE (48VDC)

• HDMl Supports: HDMI 1.4 and HDMI 2.0

• HDCP Supports: HDCP 1.X, 2.2 compliant

• Video Support: Ultra HD (4K2K@30Hz) with YCbCr 4:4:4 and 4K2K@60Hz YCbCr 4:2:0, format up to 1080p@60Hz@48b/pixel

and deep color, 3D

• Video Bandwidth: 10.2 Gbps (340MHz)

• Audio I/O Supports: Multi Audio Formats 5.1/7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital, DTS, DTS-HD Master,

(PCM-2CH)

• Extra S/PDIF I/O: External Bi-Directional SPDIF in/out, Dolby Digital, DTS, Dolby TrueHD, DTS HD-Master Audio, Dolby Pro Logic Iiz 7.1 & 9.1, and more.

• Ethernet Support: 100bps BaseTx

• KVM Support: USB 2.0

• IR Infrared Frequency: 38Khz

• Power Over HDBaseT™: 48VDC (100W power using PoH)

• Category Cable Support: CAT6, CAT6a, CAT7 UTP/STP cable

• Scan Rate Accepted: Supports HDMI full HD Resolution; Frequency 24Hz to 240Hz

• Controls: 1x IR in, 1x IR out, 1x RS-232 I/O, 1x USB (Host), 2x USB (Device) and 2x LAN series interface

• Transfer Distance: Up to 10.2Ghz/297Mhz, 328 feet(100 meters)/4K2K / Up to 4GHz/148.5Mhz, 492 feet(150 Meters)/1080p

• HDMI I/O Connectors: HDMI Type A-SMD 19pin Female Type

• HDBaseT™ I/O Connectors: HDBaseT™ RJ-45, 8p8c Female socket

• PoE Support: Transmitter (48VDC) to Receiver

• Temperature: Operating Temperature 32°F - 100°F (0°C - 38°C)

• Chassis Material/Color: Metal (think 1mm) / Black

• Dimensions (LxWxH): 8.26 x 4.45 x 1.06 in (210x113x 27 mm)

• Rack Mount (19 inch): #1U high 19 inch install 1x Unit. / #5U high 19 inch install Total 10 pcs Rack mountable

• Shipping Weight (net): Transmitter: 0.70 kgs/1.54 lb - Receiver: 0.58 kgs/1.27 lb

• Safety Approvals: CE, FCC, VCCI & REACH

• Power Consumption:

•Transmitter: 4K Full load

•w/ PoE: Max 300mA (48VDC, 12.48W)

•w/o PoE: Max 400mA (12VDC, 4.8W)

•Receiver: 4K Full load

•w/o PoE: Extra power Max 500mA (12VDC, 6.0W)

• Transmitter Power Supply: Power Input +48VDC, 1A (Universal Type 50/60Hz, 100~240 VAC)

• Receiver Power Supply: Extra Power Input +12VDC, 1A (Universal Type 50/60Hz, 100~240 VAC) (Using Exra power when

HDBaseT™ Transmitter w/o support PoE)

As product improvements are continuous, specications are subject to change and without notice.

TRANSMITTER FRONT PANEL

FRONT PANEL

1. POWER ON SWITCH: The power switch turns the unit on and off. The LED will illuminate blue to indicate that the switcher is ON and

is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last

conguration will be evoked.

2. PoE LED DISPLAY: Power over HDBaseT™ boot on and off status via LED show out.

3. LINK LED DISPLAY: HDBaseT™ link status via LED illuminates blue to indicate that a HDBaseT™ is present on that input.

4. HDCP LED DISPLAY: HDCP status via LED show out.

5. FIRMWARE UPDATE: Firmware Update connection this OD3.5mm jack port.

6.DISTANCE SELECT SWITCH: Select Extend distance for 100 meters / 4K2K or 150 meters / 1080p.

7. USB HOST: Setup the USB port is HOST.

8. USB DEVICE: Setup the USB port is DEVICE.

9. SELECT HOST OR DEVICE SWITCH: Switch Select the USB is HOST or DEVICE.

TRANSMITTER BACK PANEL

BACK PANEL

1. POWER INPUT: DC48V, 1A, (Din-4pins Male Plug).

2. RS-232 I/O: Send RS-232 via HDBaseT™ CATx cable.

3. SPDIF OUTPUT: Receive the SPDIF signal from HDBaseT™

Receiver via HDBaseT™ CATx cable.

4. SPDIF INPUT: Send the SPDIF signal to HDBaseT™ Receiver via

HDBaseT™ CATx cable.

6. HDMI INPUT: HDMI signal Input.

7/8. AUDIO INPUT: Extra Stereo Audio signal Input.

9/10. LAN I/O: LAN controls I/O.

11. IR OUTPUT: Receive Bi-directional IR signal from HDBaseT™

Receiver to Control source device.

5. HDBaseT™ OUTPUT (Transmitter): HDBaseT™ send HDMI

Source signal to Receiver via HDBaseT™ RJ-45 connector.

12. IR INPUT: Send Bi-directional IR signal to HDBaseT™ Receiver

to Control destination device.

RECEIVER FRONT PANEL

FRONT PANEL

1. POWER LED DISPLAY: The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and

is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last

conguration will be evoked.

2. PoE LED DISPLAY: Power over HDBaseT™ boot on and off status via LED show out.

3. LINK LED DISPLAY: HDBaseT™ link status via LED illuminates blue to indicate that a HDBaseT™ is present on that input.

4. HDCP LED DISPLAY: HDCP status via LED show out.

5. FIRMWARE UPDATE: Firmware Update connection this OD3.5mm jack port.

6. DISTANCE SELECT SWITCH: Select Extend distance for 100M / 4K2K or 150M / 1080p.

7. USB HOST: Setup the USB port is HOST.

8. USB DEVICE: Setup the USB port is DEVICE.

9. SELECT HOST OR DEVICE SWITCH: Switch Select the USB is HOST or DEVICE.

RECEIVER BACK PANEL

BACK PANEL

1. POWER INPUT (Extra): DC12V, 1A, (Male Plug). Extra power offer

when Transmitter PoE absent.

2. RS-232 I/O: Send RS-232 via HDBaseT™ CATx cable.

3. SPDIF INPUT: Send the SPDIF signal to HDBaseT™ Receiver via

HDBaseT™ CATx cable.

4. SPDIF OUTPUT: Receive the SPDIF signal from HDBaseT™

Receiver via HDBaseT™ CATx cable.

6. HDMI OUTPUT: HDMI signal Output to destination.

7. AUDIO OUTPUT: Extra Stereo Audio signal output.

8./9. LAN I/O: LAN controls I/O.

11. IR INPUT: Send Bi-directional IR signal to HDBaseT™

Transmitter to Control destination device.

5. HDBaseT™ INPUT: ( From Transmitter) HDBaseT™ sends HDMI

Source signal from Transmitter via HDBT RJ-45 connector.

12. IR OUTPUT: Receive Bi-directional IR signal from HDBaseT™

Receiver to Control source device.

IR PIN CONFIGURATION - TRANSMITTER

REAR PANEL IR EXTENDER PORT - TRANSMITTER

Note: When you plug the External IR extender into the switcher, the front panel IR receiver remains active.

IR EXTENDER PACKAGE

HOW TO SETUP THE IR EXTENDER RECEIVER COMPONENTS

Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.

IR PIN CONFIGURATION - RECEIVER

REAR PANEL IR EXTENDER PORT - RECEIVER

Note: When you plug the External IR extender into the switcher, the front panel IR receiver remains active.

IR EXTENDER PACKAGE

HOW TO SETUP THE IR EXTENDER RECEIVER COMPONENTS

RS-232 PIN CONFIGURATION - TRANSMITTER

HDBASET™ EXTENDER - TRANSMITTER RS-232 PIN CONFIGURATION

Note: When you plug the External IR extender into the switcher, the front panel IR receiver remains active.

HDBASET™ EXTENDER - TRANSMITTER FIRMWARE UPDATE OD3.5MM JACK PIN CONFIGURATION

RS-232 PIN CONFIGURATION - RECEIVER

HDBASET™ EXTENDER - RECEIVER RS-232 PIN CONFIGURATION

Note: When you plug the External IR extender into the switcher, the front panel IR receiver remains active.

HDBASET™ EXTENDER - RECEIVER FIRMWARE UPDATE OD3.5MM JACK PIN CONFIGURATION

TYPICAL HDBaseT™ TRANSMITTER/RECEIVER APPLICATION

INSTALLING DIAGRAM

SAMPLES CONNECTION :

1. Using HDBaseT™ Transmitter and Receiver to extend the 4K HDMI signals and control bi-directional IR in/out, RS-232 I/O, Ethernet I/O, SPDIF Audio in/out or KVM

(USB2.0 series interface).

2. The Total distance 328 feet (100M) via CATX (CAT5e, CAT6, CAT6a, CAT7) category cable.

19 INCH RACK MOUNT APPLICATIONS

1U RACK MOUNT (OPTIONAL)

SB-6077: Complete 19 inch 1U rack mount Install Application: SB-6355T/SB-6355R 19 INCH 4U-01P RACK MOUNT Parts No.: MEER60770013000

Model No.: #1U-01p-L210MM-COV

SB-6355T/SB-6355R 1U Ear mount pairs

Parts No.: MEER6300ER1102

Application Diagram: #1U 19 inch - 1x Unit (HxL) (27x210mm)

19 INCH RACK MOUNT APPLICATIONS

5U RACK MOUNT (OPTIONAL)

SB-6078: Complete 19 inch 5U rack mount Install Application: SB-6355T/SB-6355R 19 INCH 5U-10P RACK MOUNT Parts No.: MEER6078001300

Model No.: #5U-10p-L210MM-COV

SB-6355T/SB-6355R 5U Ear mount pairs

Parts No.: MEER6078ER11000

Model No.: #5U-10p-L210MM-EAR

SB-6355T/SB-6355R 5U Rack mount ear pairs

Parts No.: MEER1616HA10000

Application Diagram: #5U 19 inch - 10xUnit (HxL) (27x210mm)

19 INCH RACK MOUNT APPLICATIONS

WALL MOUNT: (OPTIONAL)

SB-6355T/SB-6355R: Wall mount accessories Model No.: #WM-1INCH-L210MM Install Application: SB-6355T/SB-6355R WALL MOUNT Parts No.: MEER6300ER11000

Application Diagram: #1 inch HIGH - 1x Unit (HxL) (27x210mm)

LIMITED WARRANTY

PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime, without notice to you.

RESTRICTIONS ON USE OF THE PRODUCT

It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.

The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product

are licensed to you by SHINYBOWUSA, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “SHINYBOWUSA”) for your

personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.

The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only. SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.

The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its ofces within the State of Texas, United States of America. SHINYBOWUSA

makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls. Disclaimers and Limitation of Liability

SHINYBOWUSA may change or modify the Product at any time, from time to time.

THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE.

SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.

TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY SHINYBOWUSA.

UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.

END OF DOCUMENT

122 Rose Ln. Suite 303

1-877-SHINY-USA 1-877-744-6987 1-972-377-2508

sales@shinybowusa.com

Frisco, Texas 75034

www.shinybowusa.com

Shinybow USA SB-6355 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual