MULTIMEDIA AUDIO AND VISUAL
MODEL : SB-6335R4/T4 KIT
HDMI HDBaseT EXTENDER
HDMI HDBaseT EXTENDER Receiver with Ethernet
INSTRUCTION MANUAL
HDMI HDBaseT EXTENDER TRANSMITTER with Ethernet
HDMI-HDBaseT EXTENDER Series
Thank you for purchasing the SB-6335R4/T4 HDMI-HDBaseT with Ethernet Receiver & Transmitter. You will
fi nd this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before
attempting to use these converters.
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fi re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
fl ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualifi ed service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports fi rst, then remove the power cable; fi nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifi er service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
TABLE OF CONTENTS
CONTENTS
INTRODUCTION ...............................................................1
FEA TURES & CONTENTS ................................................ 2
SPECIFICA TIONS ............................................................. 3
TYPICAL HOOKUP AND OPERATION ............................. 4
RACK MOUNTS (OPTIONAL) ........................................... 6
IR EXTENDER ................................................................. 8
INTRODUCTION
Congratulations on your purchase of one of the most innovative
HDMI 1.4a over single category cable Transmitter with Ethernet &
HDMI over HDBaseT with Ethernet Receiver on the market today.
The HDBaseT Receiver can receive the HDMI, IR in, IR remote
out, RS-232 in, RS-232 out and Ethernet signals from HDBaseT
Transmitter via a single category cable for long distance maximum
328 feet (100 meters). SB-6335R4 use single category LAN cable
CAT6, CAT6a or CAT7 (UTP or FTP) with RJ-45 8P8C connector
and support 568a or 568b color specifi cation table. This HDBaseT
receiver product provide the higher full HD HDMI resolutions
480i/p, 720p,1080i/p quality that are identical to the source to the
HD destination display. Control and receive signals are useful
the HDMI digital Video, digital multi-channel audio signals, IR
in, IR out, Bi-directional RS-232 series interface in or out and
Ethernet series interface control via single category cable from the
HDBaseT Transmitter.
SB-6335T4 HDBaseT Transmitter can transmit the HDMI signal,
IR Remote signals input or output, RS-232 interface signal I/O
and Ethernet series interface to the other size HDBaseT Receiver
(SB-6335R4) via single category LAN cable for the long distance
Maximum 328 feet (100M). Transmitter use the single UTP/
FTP(category cable) CAT5e, CAT6, CAT6a or CAT7 via RJ-45
8P8C female socket. The LAN cable support the 568a or 568b
LAN color specifi cation table. This product provide higher full HD
HDMI 1.4a, Resolution supports 480i/p, 720p,1080i/p or High
4K2K quality that are identical to the source high quality full HDMI
1.4 signals. The Transmitter is useful for sending the HDMI digital
Video / multi-channel audio format, IR remote in or out, RS-232
series in, RS-232 out and Ethernet. Controls signals via Single
category cable transmit to the HDBaseT Receiver.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fi re,
electrical shock and injury to persons.
• To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for suffi cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer fi le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent.
© Copyright 1997. All Rights Reserved.
Version 1.2 MAR 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
1
FEATURES & CONTENTS
FEATURES
RECEIVER
• HDBaseT HDMI Receiver over single CAT6/6a/7 category LAN cable.
• Extend for HDMI, IR in/out, RS-232 in/out and Ethernet ports, with HDCP compliant.
• Support category cable via using the CAT6, CAT6a and CAT7 UTP/FTP cable.
• Support link speeds of up to 3.4 Gbps
• Support Digital RGB 36bits, V1.4a HDMI TMDS format.
• Extension higher quality DVI video 1920x1200 resolution.
• Support HD High Defi nition full range resolution 480p, 720p 1080i/1080p
• Support long distance 100M between HDBaseT Transmitter and HDBaseT Receiver.
• Support wall mount pack and rack mount install for 19 inch 4U Rack mountable.
• Power support DC input with Low power consumes (Full load 850mA)
• Power supply using universal power switch 50/60Hz,100~240VAC.
TRANSMITTER
• HDBaseT Transmitter Extend the HDMI over single CAT5e/6/6a category 100M LAN cable.
• Transmit signals HDMI, IR in/out and RS-232 I/O series interface.
• Single category cable via using the CAT6, CAT6a and CAT7 (UTP or FTP) cable.
• Support link speeds of up to 3.4 Gbps, HDMI 1.4, full HD 4K2K signal, HDCP compliant.
• Support Digital RGB 36bits, HDMI digital video TMDS, digital multi-channel audio format.
• Extension higher quality full HD DVI video WUXGA 1920x1200 resolution.
• Support High Defi nition worldwide range resolution 480p, 720p 1080i/1080p-60Hz and 4K2K.
• Extend long distance 328 feet (100M) between HDBaseT Transmitter and Receiver.
• Support wall mount install total 10 pcs. into one 19 inch 4U Rack mountable.
• Power input via DC with Low power consumes (Full load 750mA)
• Power supply using universal power switch 50/60Hz,100~240VAC.
PACKAGE CONTENTS
Check that you have the following components;
• SB-6335x4 HDBaseT Receiver & Transmitter console
• SB-100 set (IR Receiver Extender assy plug).
• SB-100C cable (IR Receiver Cable).
• SB-101 set (IR Transmitter Extender assy plug).
• SB-101C cable (IR Transmitter Cable).
• 1 inch High Wall mount pack (Part # WM-1INCH-L80MM)
• Users Guide
• (2) AC/DC Adapter: 12VDC, 2A. (universal power switch 50/60Hz,100~240VAC)
OPTIONAL ACCESSORIES
(1) 1x SB-100 set (IR Receiver Extender assy plug).
(2) 1x SB-100C cable (IR Receiver Cable).
(3) 1x SB-101 set (IR Transmitter Extender assy plug).
(4) 1x SB-101C cable (IR Transmitter Cable).
(5) 1x 1 inch High Wall mount pack (Part # WM-1INCH-L80MM).
(6) 1x CAT6 Category cable distance 328 feet (100 M), (P/N: UTP6-100)
2
SPECIFICATIONS
SPECIFICATIONS
RECEIVER
• Type of Extender: HDBaseT Receiver for HDMI signal over one category LAN Cable
• Input Signals: HDMI with Digital Video(TMDS)/Audio 0.5~1.0vPP, DDC 5Vpp
• HDBaseT Supports: HDMI Standard, DVI and HDCP Compliant
• Video Support: HDMI and DVI TMDS format for 1920x1200 resolution up to 3.4 Gbps Digital RGB 36bits deep color , 3D 1.4a HDMI format
• HDMI Audio Out Supports: Multi-channel Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus,
DTS, DTS-ES 6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Ethernet Support: 1x Ethernet port (100bps)
• Category Cable Support: CAT6, CAT6a, CAT7 UTP/FTP cable
• Support HDMI Resolution: 480p, 720p, 1080i/1080p, 4k2k
• Scan Rate Accepted: Support HDMI full HD Resolutions; Frequency 24Hz to 60Hz
• Control: 1x IR in/out, 1x IR in/out, 1x RS-232 and 1x LAN series interface
• IR Infrared Frequency: 38Khz
• Extend Distance: Up to 100M (CAT6)
• Safety Approvals: CE, FCC, VCCI, REACH & WEEE
• Dimensions (LxWxH): 5.12 x 5.12 x 1 in (130mm x 130mm x 26mm)
• Rack Mount : Use total 10 pcs install into one 19 inch rack mountable
• Shipping Weight: 0.4775 kgs / 0.82 lb
• Power Consumption: Max. 0.850mA. (Full load 1080p-60Hz signal with use DC12V input)
• Power Supply: Power Input +12VDC, 2A, (Universal Type 50/60Hz, 100~240 VAC)
TRANSMITTER
• Type of Extender: HDBaseT Transmitter for HDMI over single category 100M Cable
• Input Signals: HDMI with Digital Video(TMDS)/Audio 0.5~1.0vPP, DDC 5Vpp
• HDBaseT Supports: HDMI 1.4 Standard, DVI and HDCP Compliant
• Video Support: HDMI and DVI TMDS format for 1920x1200 resolution up to 3.4 Gbps Digital RGB 36bits deep color , 3D 1.4a HDMI format
• Audio I/O Supports: Multi-channel Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby T rueHD, Dolby Digital Plus, DTS, DTS-
ES 6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• PoH Distance: Non
• Cable Support: CAT6, CAT6a, CAT7 use UTP or FTP category cable
• Support HDMI Resolution: 480p, 720p 1080i/1080p@60Hz or 4K2K@24Hz
• Scan Rate Accepted: Support HDMI full HD Resolutions; Frequency 24Hz to 60Hz
• Control: 1x IR in, 1x IR out and 1x RS-232 I/O series interface
• IR Infrared Frequency: 38Khz
• Safety Approvals: CE, FCC, VCCI, REACH & WEEE
• Dimensions (LxWxH): 5.12 x 3.14 x 1.14 in (130mm x 80mm x 29mm)
• Wall Mount: Wall mount pack (p/n:VM-1inch-L80MM)
• Rack Mount : Total 13 pcs install into 19 inch 4U Rack mountable
• Shipping Weight: 0.375 kgs / 0.825 lb
• Power Consumption: Max. 750mA. (Full load 1080p-60Hz signal with use DC12V input)
• Power Supply: Power Input +12VDC, 2A, (Universal Type 50/60Hz, 100~240 VAC)
As product improvements are continuous, specifi cations are subject to change and without notice.
3
TYPICAL HOOKUP AND OPERATION - RECEIVER
FRONT PANEL: SB-6335R4
1. Status via LED Show out : POWER, LINK & HDCP.
2. PoH turn OFF led.
3. 1x Ethernet series interface path to HDBaseT Transmitter.
4. 1x Firmware update port.
REAR PANEL: SB-6335R4
5. DC input : DC12V, 2A
6. RJ-45 IN : HDBaseT input , Signal from the HDBaseT Transmitter
7. HDMI OUT : HDMI output , Signal to HDMI destination display device
8. IR IN : Send IR signal to HDBaseT Transmitter
9. IR OUT : Receive IR signal from HDBaseT Transmitter via IR External Receiver SB-100)
10. RS-232 I/O : RS-232 series interface in or out control via a PC
INSTALLING DIAGRAM
4
TYPICAL HOOKUP AND OPERATION - TRANSMITTER
FRONT PANEL: SB-6335T4
1. Status via LED Show out : HDCP, LINK & POWER
2. Turn OFF PoH(Power Over HDBaseT).
3. 1x Ethernet path to HDBaseT Receiver.
4. 1x Firmware update port
REAR PANEL: SB-6335T4
5. DC input : DC12V, 2A
6. RJ-45 OUT : HDBaseT signal output to HDBaseT Receiver
7. HDMI IN : HDMI signal input from HDMI source device
8. IR IN : Sending IR Signal To HDBaseT Receiver
9. IR OUT : Receive IR signal from HDBaseT Transmitter
10. RS-232 I/O : RS-232 I/O series interface via HDBaseT
INSTALLING DIAGRAM
5
RACK MOUNT (optional)
SB-6069
SB-6335T4/SB-6335R4 19 INCH 4U-10P RACK MOUNT
Model No. :
SB-6335T4/SB-6335R4 4U Ear mount pairs
Parts No.: MEER6069ER13000
Model No. : #4U-10p-L130MM-COV
SB-6335T4/SB-6335R4 4U Ear mount pairs
Parts No.: MEER6069ER11000
#4U-10p-L130MM
Model No. : #4U-10p-L80MM-EAR
SB-6335T4/SB-6335R4 4U Ear mount pairs
Parts No.: MEER6320ER11001
6
SB-6069
Complete 19 inch 4U rack mount
RACK MOUNT (optional)
Install (10 units) Application :
SB-6335T4/SB-6335R4 : Wall mount accessories
Model No. : #WM-1INCH-L80MM
SB-6335T4/SB-6335R4 Wall mount pairs
Parts No.: MEER6320ER11000
SB-6335T4/SB-6335R4
7
IR RECEIVER:
IR EXTENDER
1. SB-100 IR 300M Receiver
SB-100
IR Receiver Set
2. SB-100C IR 2M Receiver
Device Cable (3C) IR Receiver (SB-100)
RoHS /95/EC
INPUT
RS-232 IR EXT. in
RS-232
IR EXT .
DC 12V
IR Rx
SB-100
SB-100 Maximum Distance ~ 984 feet (300 meters)
Device Cable (3C) IR Receiver (SB-100C)
IR Receiver cable 6ft (2M)
RoHS /95/EC
INPUT
DC 12V
4
4
3
1
-
4
T
F
3
F
U
R
O
E
P
2
-2
W
4
O
T
IN
P
3
R
U
3
E
P
2
-
N
IR Rx
SB-100
O
H
N
1
T
I
C
U
T
I
4
P
2
-
W
N
1
T
I
S
U
X
I
P
23
R
N
1
I
T
A
M
I
1
M
D
H
SB-100C Maximum Distance ~ 6 feet (2 meters)
SB-100C
IR Receiver Cable
RS-232 IR EXT. in
RS-232
IR EXT .
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
PIN CONFIGURATION:
4
4
3
1
-
4
T
F
3
F
U
R
O
E
P
2
-2
W
4
N
O
T
I
P
3
R
U
3
E
P
2
-
N
H
O
N
1
T
I
C
3
U
IT
4
P
2
-
W
N
1
T
I
S
U
X
I
P
2
R
N
1
I
T
A
M
I
1
DM
H
IR
W
S
R
SW I
SB-100 and SB-100C Receiver Pin configuration
Tip: Signal
Ring :VCC
Tip
Ring
Ring
Sleeve
Sleeve: GND
SB-100
IR Receiver Set
Sleeve
Tip (center)
SB-100 Maximum Distance ~ 984 feet (300 meters)
IR Receiver cable 6ft (2M)
Tip: Signal
Ring: NC
Tip
Ring
Ring
Sleeve
Sleeve: GND
SB-100C
IR Receiver Cable
Sleeve
Tip (center)
SB-100C Maximum Distance ~ 6 feet (2 meters)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug
(aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the
switcher power off.
VCC (Ring)
GND (Sleeve)
Signal (center)
GND (Sleeve)
Signal (center)
8
IR EMITTER:
p
IR EXTENDER
1. SB-101 IR 300M Transmitter
DC 12V
RoHS/95/EC
SB-101
IR Transmitter Set
2. SB-101C IR 2M Transmitter
Device Cable (3C) IR Transmitter (SB-101)
IR out
From
Receiver
IR in
To
Receiver
CAT6/6a/7
OUTPUT
IR Tx
SB-101
SB-101 Maximum Distance ~ 984 feet (300 meters)
Device Cable (3C) IR Transmitter (SB-101C)
IR Transmitter cable 6ft (2M)
SB-101C
DC 12V
RoHS/95/EC
Transmitter Cable
IR out
From
Receiver
IR in
To
Receiver
CAT6/6a/7
OUTPUT
IR Tx
SB-101C
SB-101C Maximum Distance ~ 6 feet (2 meters)
*** When you plug the External IR extender into the switcher, the front panel IR transmitter remains active. ***
PIN CONFIGURATION:
SB-101 and SB-101C Transmitter Pin configuration
Tip: Signal
Ring :VCC
Sleeve: GND
SB-101
SB-101 Maximum Distance ~ 984 feet (300 meters)
IR Transmitter cable 6ft (2M)
SB-101C
SB-101C Maximum Distance ~ 6 feet (2 meters)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug
(aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the
switcher
IR Transmitter Set
Transmitter Cable
ower off.
Tip: Signal
Ring: NC
Sleeve: GND
Tip
Tip
Ring
Sleeve
Ring
Sleeve
Ring
Tip (center)
Ring
Tip (center)
9
Sleeve
Sleeve
VCC (Ring)
GND (Sleeve)
Signal (center)
GND (Sleeve)
Signal (center)
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTW ARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its affi liates, including any manufacturers or distributors of the Product (collectively , “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its offi ces within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENT A TIONS REGARDING THE USE OR THE RESUL TS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT W ARRANT THA T THE FUNCTIONS PERT AINING TO THE PRODUCT WILL BE ERROR-FREE, THA T DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERT AINING THERET O ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THA T RESUL T FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
10
MULTIMEDIA AUDIO AND VISUAL
122 Rose Ln. Suite 303 | Frisco, Texas 75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com
www.shinybowusa.com
Loading...