Shinybow USA SB-5688CT-A Instruction Manual

SB-5688CT-A

8x8 HDMI-HDBaseT™ Matrix Switch with Audio and Extension

INSTRUCTION MANUAL

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal

ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to

qualied service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.

19. Service Information Equipment should be serviced by qualier service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS

HDMI-HDBaseT™ Matrix Switcher Series

Thank you for purchasing the SB-5688CT-A HDMI-HDBaseT™ Matrix Switcher. You will nd this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use matrix switcher.

CONTENTS

PACKAGE CONTENTS .................................................. 1

INTRODUCTION ..............................................................2

FEATURES ....................................................................... 2

SPECIFICATIONS ............................................................ 3

FRONT PANEL ................................................................ 4

REAR PANEL ................................................................. 7

REMOTE CONTROL ....................................................... 9

REMOTE PROTOCOL COMMANDS ............................ 10

EDID FUNCTIONS ......................................................... 12

TYPICAL APPLICATION ............................................... 15

IR EXTENDER ............................................................... 18

ETHERNET SERIAL INTERFACE ................................ 20

RS-232 PROTOCOL .................................................... 20

PACKAGE CONTENTS

Check that you have the following components;

• SB-5688CT-A Matrix Switcher

• RS-232 V2.0 Protocol Instructions

• Master wireless IR Remote Control (SW-5688)

• (8) Individual wireless IR Control (SW-5688CTA-IR01~IR08)

• 19 inch Ear mount bracket (Part # 2U-440L)

• SB-101 IR Extender distance 300M (1000 ft) Transmitter set

• SB-100 IR Extender distance 300M (1000 ft) Receiver set

• SB-101C IR Extender distance 2M(6 ft) Transmitter Cable

• SB-100C IR Extender distance 2M(6 ft) Receiver Cable

• CD Contents : Manual, Windows GUI, ISP V1.0 Windows driver

• RS-232 Cable 6 feet (2M)

• Users Guide

• Worldwide Universal Power Supply 100~230VAC, AC 50/60Hz,

10A

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the

following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain, moisture

or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any openings

or empty slots in the unit, as you may damage parts inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufcient

space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.

We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.

We reserve the right to make improvements to this document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language

or computer le, in any form or by any means — electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without express

written permission and consent

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

INTRODUCTION & FEATURES

INTRODUCTION

The SB-5688CT-A is high-performance 8x8 matrix routing switcher with (8) HDMI with DVI-Audio inputs and supports simultaneously (8) HDMI with DVI-Audio and (8) CATx outputs. The SB-5688CT-A is based on HDBaseT™ technology and that supports full resolution HDMI Video with embedded audio, RS-232, and IR bidirectional, all over a single CATx cable. With a signal bandwidth of 340Mhz, there

is no signal degradation. High Denition Digital signals can be selected and distributed to any (16) outputs simultaneously (8x channels x2). The Switcher is certied as being fully CEC and HDCP 2.0 compliant, HDMI V1.4a 3D formats, data rates up to 6.75 Gbps. Supports

UXGA/WUXGA/DVI 1920x1200 resolution to any HD displays. The SB-5688CT-A has one CAT6/CAT6a and HDMI connector for each output, effectively making this an 8x16 switcher (same signal on both outputs). (1) RJ-45 connection on each output extends the HDMI signal to remote location via HDBaseT™ CATx cable extend to HDBaseT™ Receiver. The EDID can be selected between (8) different modes. Control is provided via front panel push buttons, IR remote or via RS-232 or TCP/IP (not a web-browser). An RS-232 Windows GUI interface is provided for matrix routing.

FEATURES

Based on HDBaseT™, bi-directional IR, RS-232, Multi format Audio, Ethernet and full resolution HD Video all, signals over CATx (6/6a/7) cable.

• 8x HDMI with DVI-Audio source devices matrix switched to 8x HDMI with (HDMI/DVI) SPDIF and 8x CATx(6/6a/7) Extender output devices

• Application HDBaseT™ Specication for IR, RS-232, Multi Audio Format and HD Video Signals over CATx

• HDMI digital Video w/ embedded Audio, DVI format and CEC/HDCP 2.0 compliant

• Worldwide control EDID modes for HD Video resolutions

• Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 1.4a 3D formats

• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p,

1080i & 1080p

• Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers or audio ampliers

• Digital Video TMDS formats Resolution up to 1080p-60 with Deep color 36-bit

• Digital Audio Support : Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX PCM, PCM2, LPCM2

• Audio Input : Support DVI Audio

• Audio Output : Support HDMI or DVI Audio with S/PDIF (LPCM 2-CH or Maximum 5.1CH)

• Various User Interface control:

• Windows based GUI control via RS-232 port

• Front Panel push button

• IR wireless remote control

• Ethernet Switcher control

• Third party RS-232 controller (via simple ASCII)

• Support world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK

• Support EDID modes : Embedded EDID modes : FSS/H24-3D/H24-3D-M/H36-3D/H36-3D-M/DVI-D

1280x1024-60Hz/DVI-D 1920x1200-60Hz/AUTO

External modes : Learning mode

• Automatic scanning input & output status via LCM show on front panel

• Support IR Remote and IR Extender with distance up to ~ 1000 feet (300M) Max

• EDID conguration via Internal modes

• Consumer Electronic Control (CEC) switch all open or OFF

The Switcher will remember that last state during a power cycle.

When power is removed and resorted, the last conguration will be invoked.

SPECIFICATIONS

• Type of HDMI Switcher: 8x HDMI inputs To 8x HDMI + 8x HDBaseT™ Outputs with Audio Matrix Switcher

• HDMI Support: HD 1080p-@60Hz, H36-bit Deep color, 3D of HDMI V1.4a formats

• HDCP / CEC Support: HDCP 2.0 Compliant, CEC Compliant

• Video Bandwidth: Double Data Rates: 340Mhz, Total 6.75Gbps bandwidth

• Digital Video Support: HD: 480i/ 480p/ 720p/ 1080i/ 1080p up to 36bit deep color

• Digital Audio Support: Multi Audio Formats 5.1 / 7.1, MAT(MLP) Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES

6CH, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)

• Inputs:

• 8x HDMI Sources

• 1x Audio (DVI Audio)

• 1x IR Ext. in ( Switcher control)

• 8x IR in (IR signal To 8x Rooms each - Via HDBaseT™ CATx cable)

• 1x ALL IR in (IR to Room - Via HDBaseT™ CATx cable)

• 1x RS-232 (Switcher control)

• 8x RS-232 (I/O To 8x Rooms - Via HDBaseT™ CATx cable)

• Outputs:

• 8x HDMI Destinations

• 1x SPDIF (HDMI 5.1CH or DVI Audio)

• 8x CATx (HDBaseT™ Based via category 6/6a/7 cable)

• 1x ALL IR out (IR signals from Room - Via HDBaseT™ CATx cable)

• 8x IR out (IR signal from 8x Rooms each - Via HDBaseT™ CATx cable)

• 8x RS-232 ( I/O From 8x Rooms each - Via HDBaseT™ CATx cable)

• Controls:

• 1x IR Remote Controller (remote switcher)

• 8x IR Room Remote Controller

• 1x IR External port x 1 (OD 3.5mm Ear phone Jack)

• 1x Select & Function buttons on front panel

• 1x RS-232 series interface (switcher control)

• 1x Ethernet series interface (switcher control)

• Source Status: Automatically Scan Sources Inputs via LED show out

• Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID

• (8) EDID management: Select Embedded EDID :

• 1: FSS

• 2: H24-3D

• Mode3: H24-3D-M

• Mode4: H36-3D

• Mode5: H36-3D-M

• Mode6: DVI-D 1280x1024-60Hz

• Mode7: DVI-D 1920x1200-60Hz

• Mode8: AUTO

• Infrared Frequency: 38 Khz

• IR External Distance: ~1000 feet / 300 meters maximum

• HDBaseT™ Extender Distance: ~300 feet / 100 meters maximum

• HDMI I/O Connector: HDMI Type A - SMD 19pin Female Type

• Temperature: 32°F - 100°F Operation (0°C - 38°C)

• Dimensions (LxWxH): 19 x 9.85 x 3.5 in (482x250x88mm)

• Rack Mount: 2RU High 19 ”Rack Mount #2U-440L (with rack mount)

• Power Supply: AC 100~240 VAC 50/60Hz (Power Consumption:10A Maximum)

• Safety Approvals: CE, FCC, RoHS, REACH

• Product Weight: 4.75 Kgs / 7.91 lb

As product improvements are continuous, specications are subject to change without notice.

FRONT PANEL

1. POWER SWITCH: The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and

is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last

conguration will be evoked.

2. INPUT STATUS DISPLAY: Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input.

3. OUTPUT STATUS DISPLAY: Each Output (destination) Channel shows which input (source) is assigned.

4. DESTINATION SELECT BUTTONS: Separate outputs 1 thru 8 select buttons are provided for each destination assignment. Routing can be

Source to Destination or one source to multiple destinations.

Example : Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.

5. EDID MODE SELECT BUTTONS: Used to select EDID mode using buttons #1 thru #2

6. IR SENSOR: The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.

7. SOURCE SELECT BUTTONS: Separate inputs 1 thru 8 select buttons are provided each source selection.

8. 19 INCH EAR MOUNT PAIR: Converts desktop to 19 inch rack mount. Bracket (part # 2U-440L) INCLUDED. Image shows rack mount

bracket attached.

FRONT PANEL

8. FUNCTION KEY - ALL:

Disables (mute) video on all destinations OR Selects the same source to all destinations.

Option 1

- Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected.

Option 2

- Press ALL followed by Source 1 thru 8. The display will show the Source selected.

- Press ENTER The pre-set source selection will be assigned all destinations.

9. FUNCTION KEY - OFF:

Disables (mute) video to selected channels. Either destinations.

- Press OFF button followed by any Destination channel.

- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected.

10. FUNCTION KEY - ENTER: Press ENTER to conrm entries.

11. FUNCTION KEY - LOCK:

- Press and hold LOCK button for two seconds lockout the front panel.

- Press and hold LOCK button for two seconds to enable the front panel.

FRONT PANEL

12. FUNCTION KEY - RECALL:

The system will show previously stored presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.

- Press RECALL button.

- Press 1 thru 8 on either Source or Destination row.

- Press ENTER The pre-set conguration will execute.

Operation completes. Operation will abort if no keys are pressed with 5 seconds.

13. FUNCTION KEY - MEMORY:

The system will show store presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.

- Congure desired matrices.

- Press MEMORY button.

- Press 1 thru 8 on either Source or Destination row.

- Press ENTER to ready memory location.

- or press MEMORY again to cancel operation.

Operation completes.

Note : Operation will abort if no keys are pressed within 5 seconds.

14. FUNCTION KEY - EDID:

- Press EDID to select new EDID mode or select source row #1 or #2 for LINK source EDID again.

- Press DESTINATION again, press the same DESTINATION # to learn CATx EDID, The EDID for CATx has been learned.

BACK PANEL

1. DC POWER INLET: The Switcher is tted with a AC power plug

input connector. Ensure that the used is of an approved type and

is of sufcientcurrent carrying connector capacity with the correct

voltage and connector polarity.100~240Volt AC, 50/60Hz power supply.

2. IR EXTENDER CONTROL: Support one of IR Extender. Extend

distance maximum 300M / ~1000 feet. When you plug the External IR extender into the switcher, the front panel IR receiver remain active.

3. RS-232 CONNECTION: RS-232 control port to allow for

interfacing to a PC, Such as a computer or touch panel control, to the switcher via this DB-9pin Female connector for serial RS232 control.

4. ETHERNET CONNECTION: ETHERNET control port to allow for

TCP/IP interfacing to a PC, Such as a computer or touch panel control (not a web-browser), to the switcher via this RJ-45 Female connector to control switcher.

Power Plug:

Power input - AC100~240V,50/60Hz, 10A

IR Extender Jack:

Female Jack - inner OD ᴓ 3.5 mm

Remote port :

DB-9pin Female connector

Remote port : Control the switcher RJ-45 Female connector

5./6. OUTPUTS- 1,2,3,4,5,6,7 & 8 HDMI: Connect a signal link of

HDMI direct digital video/audio to this Female HDMI connector. This connector supports HDMI digital video/audio and DVI digital video sources.

HDMI Digital Video/Audio, Connector with x screw Output 1 ~

Output 8

7./ 8. INPUTS- 1,2,3,4,5,6,7, & 8 HDMI: Connect a signal link of

HDMI direct digital video/audio to this Female HDMI connector. This connector supports HDMI digital video/audio and DVI digital video sources.

HDMI Digital Video/Audio, Connector with x screw Input 1 - Input 8

HDMI digital video/audio connector: HDMI Female connector. Note: With the proper adapters, the switcher can be used with DVI digital video signals HDCP compliant. DVI does not support audio.

SPDIF: Use RCA connector with digital audio signals output.

HDMI digital video/audio connector: HDMI Female

connector. Note: With the proper adapters, the switcher can be used with DVI digital video signals HDCP compliant. DVI does not support audio. Audio: Support the audio input when you use DVI signals.

BACK PANEL

6. RS-232- 1,2,3,4,5,6,7 & 8 CONNECTION TO CONTROL ROOM: 8x

RS-232 control port to allow for interfacing to a PC, Such as a computer or touch panel control, to the switcher via this DB-9pin Female connector for serial RS-232 control.

7. OUTPUT - 1,2,3,4,5,6,7 & 8 HDBaseT™: CAT Transmitter extend

a signal link of HDMI / RS-232 / IR Remote to this RJ-45 Female connector via CATX(6/6a) category cable. Connector with RJ-45 Output 1 ~ Output 8

8. IR REMOTE INPUT - 1,2,3,4,5,6,7 & 8 IR SIGNAL TO ROOM:

Support 8 of IR Extender to control signal to 8 rooms. Extend cable distance maximum 300 M / ~1000 feet. When you plug the CAT5e/6/7 IR extender into the external port, the room IR receiver remain active.

9. IR REMOTE OUTPUT - 1,2,3,4,5,6,7 & 8 IR SIGNAL FROM ROOM:

Support eight of IR Extender to receive signal from eight rooms. Extend cable distance maximum 300M / ~1000 feet. When you plug the CAT5e/6/7 IR extender into the external port, the room IR receiver remain active.

Remote port :

DB-9pin Female connector

CAT connector:

RJ-45 Female connector.

IR Extender Jack:

Female Jack - inner OD ᴓ 3.5 mm

IR Extender Jack:

Female Jack - inner OD ᴓ 3.5 mm

10. ALL IN : ALL HDBaseT™ IR REMOTE 1,2,3,4,5,6,7 & 8 (IR SIGNAL

TO ROOM): Support 8 of IR remote signals to control to 8 rooms

via ALL IN port. Extend cable distance maximum 300 M / ~1000 feet. When you plug the CAT5e/6/7 IR extender into the external port, the room IR receiver remain active.

11. ALL OUT : ALL HDBaseT™ IR REMOTE - 1,2,3,4,5,6,7 & 8 (IR SIGNAL

FROM ROOM): Support eight of IR remote signals from eight rooms

via ALL OUT port. Extend cable distance maximum 300M / ~1000 feet. When you plug the CAT5e/6/7 IR extender into the external port, the room IR receiver remain active.

IR Extender Jack:

Female Jack - inner OD ᴓ 3.5 mm

IR Extender Jack:

Female Jack - inner OD ᴓ 3.5 mm

REMOTE CONTROL

Before making any connections to the switcher, observe the following:

• Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%).

• Ensure that the power switch is OFF.

• Ensure that all system grounds (earth) are connected to a common point.

• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.

• Connect all audio video sources and destination equipment.

• Power up all source and destination audio-visual sources.

• For each destination output, select the appropriate input source by using the front panel input 1~8 select buttons. The supplied IR remote

control or through the RS-232 serial communications port.

• Upon power up the switcher will return to its last used setting before Powered down.

REMOTE CONTROL

IR REMOTE CONTROL KEY :

1. & 2. SWITCH POWER ON or OFF:

Controller with a separate power ON and OFF

3. DESTINATION : 1 thru 8 OUTPUT SELECTION:

Press the destination button to select the output display channel.

4. SOURCE : 1 thru 8 INPUT SOURCE SELECTION:

Press input 1~8 sources with selection button.

5. FUNCTION KEY:

ALL - function selection button OFF - function selection button EDID - function selection button RECALL - function selection button MEMORY - function selection button ENTER - function selection button LOCK - function selection button

REMOTE PROTOCOL COMMANDS

IR REMOTE CUSTOM AND DATA CODES (NEC Standard)

HOW TO SETUP IR CODES : CUSTOM CODE : 09F6

POWER ON : 09F6 A15E MEMORY : 09F6 B44B POWER OFF : 09F6 A25D LOCK : 09F6 B54A ALL : 09F6 B04F EDID : 09F6 B748 OFF : 09F6 B14E ENTER : 09F6 B34C RECALL : 09F6 B24D

PRESS DESTINATION - # then PRESS SOURCE - #

DESTINATION #1 : 09F6 10EF SOURCE #1 : 09F6 01FE DESTINATION #2 : 09F6 20DF SOURCE #2 : 09F6 02FD DESTINATION #3 : 09F6 30CF SOURCE #3 : 09F6 03FC DESTINATION #4 : 09F6 40BF SOURCE #4 : 09F6 04FB DESTINATION #5 : 09F6 50AF SOURCE #5 : 09F6 05FA DESTINATION #6 : 09F6 609F SOURCE #6 : 09F6 06F9 DESTINATION #7 : 09F6 708F SOURCE #7 : 09F6 07F8 DESTINATION #8 : 09F6 807F SOURCE #8 : 09F6 08F7

For example;

Select Destination # 1 to show Source (#1~8).

The IR Data Code list :

Destination # 1, Source #1 09F6 10EF 09F6 01FE 01FE Destination # 1, Source #2 09F6 10EF 09F6 01FE 02FD Destination # 1, Source #3 09F6 10EF 09F6 01FE 03FC Destination # 1, Source #4 09F6 10EF 09F6 01FE 04FB Destination # 1, Source #5 09F6 10EF 09F6 01FE 05FA Destination # 1, Source #6 09F6 10EF 09F6 01FE 06F9 Destination # 1, Source #7 09F6 10EF 09F6 01FE 07F8 Destination # 1, Source #8 09F6 10EF 09F6 01FE 08F7

ROOM REMOTE CONTROLS

ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES

IR CUSTOM AND DATA CODES (NEC Standard)

PRESS Number To Select SOURCE CUSTOM CODE : 09F6

IR-01 DATA CODE: IR-02 DATA CODE: IR-03 DATA CODE:

SOURCE #1 : 09F6 11EE SOURCE #1 : 09F6 21DE SOURCE #1 : 09F6 31CE

SOURCE #2 : 09F6 12ED SOURCE #2 : 09F6 22DD SOURCE #2 : 09F6 32CD

SOURCE #3 : 09F6 13EC SOURCE #3 : 09F6 23DC SOURCE #3 : 09F6 33CC

SOURCE #4 : 09F6 14EB SOURCE #4 : 09F6 24DB SOURCE #4 : 09F6 34CB

SOURCE #5 : 09F6 15EA SOURCE #5 : 09F6 25DA SOURCE #5 : 09F6 35CA

SOURCE #6 : 09F6 16E9 SOURCE #6 : 09F6 26D9 SOURCE #6 : 09F6 36C9

SOURCE #7 : 09F6 17E8 SOURCE #7 : 09F6 27D8 SOURCE #7 : 09F6 37C8

SOURCE #8 : 09F6 18E7 SOURCE #8 : 09F6 28D7 SOURCE #8 : 09F6 38C7

IR-04 DATA CODE: IR-05 DATA CODE: IR-06 DATA CODE:

SOURCE #1 : 09F6 09F6 SOURCE #1 : 09F6 51AE SOURCE #1 : 09F6 619E

SOURCE #2 : 09F6 42BD SOURCE #2 : 09F6 52AD SOURCE #2 : 09F6 629D

SOURCE #3 : 09F6 43BC SOURCE #3 : 09F6 53AC SOURCE #3 : 09F6 639C

SOURCE #4 : 09F6 44BB SOURCE #4 : 09F6 54AB SOURCE #4 : 09F6 649B

SOURCE #5 : 09F6 45BA SOURCE #5 : 09F6 55AA SOURCE #5 : 09F6 659A

SOURCE #6 : 09F6 09F6 SOURCE #6 : 09F6 56A9 SOURCE #6 : 09F6 6699

SOURCE #7 : 09F6 47B8 SOURCE #7 : 09F6 57A8 SOURCE #7 : 09F6 6798

SOURCE #8 : 09F6 48B7 SOURCE #8 : 09F6 58A7 SOURCE #8 : 09F6 6897

IR-07 DATA CODE: IR-08 DATA CODE:

SOURCE #1 : 09F6 718E SOURCE #1 : 09F6 817E

SOURCE #2 : 09F6 728D SOURCE #2 : 09F6 827D

SOURCE #3 : 09F6 738C SOURCE #3 : 09F6 837C

SOURCE #4 : 09F6 748B SOURCE #4 : 09F6 847B

SOURCE #5 : 09F6 758A SOURCE #5 : 09F6 857A

SOURCE #6 : 09F6 7689 SOURCE #6 : 09F6 8679

SOURCE #7 : 09F6 7788 SOURCE #7 : 09F6 8778

SOURCE #8 : 09F6 7887 SOURCE #8 : 09F6 8877

EDID FUNCTION

EDID FUNCTION FOR HDMI MATRIX SWITCHER

EDID Setup To Change the EDID Setup

Step 1. Press the EDID button The display will show the currently selected EDID mode

Step 2. Press SOURCE #1 or #2 button row The button will ash blue and the display will show the current Embedded EDID Status.

Step 3. Press the ENTER button To set EDID mode. The switcher will return to operation mode.

Operation will abort if no keys are pressed within 5 seconds.

RESET EDID Return To Factory default

How to RESET EDID mode

RESET To the FACTORY DEFAULT (1080p-2CH).

Press

EDID > RECALL > ENTER

Embedded EDID Modes Total 8 EDID Modes

Embedded EDID setup

Press

EDID > SOURCE > ENTER

SOURCE #1 or SOURCE #2

EDID status To view the current EDID status

Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.

Step 2. Press EDID button To exit.

How to setup FSS Function Fast speed start

Step 1. Press the Destinations #1 ~ 8 button row

Then Press the Source #1~8 button row

Step 2. Press EDID button Select a optimum status of Embedded EDID mode.

Press EDID button : The LCM will show the current EDID status.

Press RECALL button : The LCM will show the RESET EDID.

Press ENTER to conrm entries.

The EDID will return to FSS mode and resolution 1080p-2CH.

To select Embedded EDID mode or LEARNING mode.

Press EDID button: The LCM will show the current EDID status.

Repeatedly depressing the Source 1 button will cycle up thru the options.

Repeatedly depressing the Source 2 button will cycle down thru the options.

Select Embedded EDID :

Mode 1 : FSS Mode 2 : H24-3D Mode 3 : H24-3D-M Mode 4 : H36-3D

To setup and Install all devices.

Mode 5 : H36-3D-M Mode 6 : DVI-D 1280x1024-60Hz Mode 7 : DVI-D 1920x1200-60Hz Mode 8 : AUTO

Step 3. Press ENTER button To conform entries.

Step 4. Press EDID button To select the EDID FSS mode.

Step 5. Press ENTER button To conform entries.

Automodedenition Common Resolution and Audio

Switcher will nd highest common Resolution and Audio from all destination EDID to link Source.

Example for single source

Destination > press #1 and then Source > press #1

Destination device #1 will set to the highest common resolution and Audio of source #1

Example for multiple sources

Destination device #1, #2, #3 will be set to the highest common resolution and Audio available and source device #1 will output this same resolution.

EDID FUNCTION

LEARNING EDID Learning EDID from Destination to Source

Learning EDID Setup

Key Press Sequence:

Press EDID > DESTINATION Button: The LCM will be show LEARNING.

Switcher will LEARN destination HDMI EDID and pass the selected source.

EDID > DESTINATION > SOURCE > ENTER

Learning EDID setup for HDMI: Key Press Sequence:

EDID > DESTINATION # > SOURCE # > ENTER

The EDID for HDMI has been learned

Press

Switcher will LEARN destination CATx EDID and pass the selected source.

EDID > DESTINATION > DESTINATION

> SOURCE > ENTER

Learning EDID setup for CATx Key Press Sequence:

EDID > DESTINATION # > DESTINATION # > SOURCE # > ENTER

Again, Press the same DESTINATION # to learn CATx EDID The EDID for CATx has been learned

NOTE : The already learned EDID cannot be modied. You can only rebuild a new Learning EDID.

For example: When the Source has “Learned” the EDID data from a destination, It will save that EDID information into EPROM and the

EDID data cannot change. Please select new learning destination to sources or change to one of the embedded EDID modes when you want to remove the learning EDID memory from EPROM.

Learning EDID Single to Single Example : Learn Destination #8 EDID To Source #5.

Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.

Step 2. Press the Destination #8 button row Copy the Destination #8 Display EDID.

Step 3. Press the Source #5 button row Learning the Destination #8 EDID to Source # 5.

Step 4. Press ENTER button To conrm entries.

Learning EDID Single to Multiple Learning destination EDID link to the majority Sources

Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.

Step 2. Press the Destinations #1 ~ 8 button row Copy any (1~8) Destinations EDID.

Step 3. Press the Source #1, #6~#8 button row Learning the Destination EDID link to Source #1, #6 ~ #8 .

Step 4. Press ENTER button To conrm entries.

Learning EDID Single to ALL Learning destination EDID link to All Sources

Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.

Step 2. Press destination button (1 thru 8) Learning anyone (1~8) Destination EDID to all sources.

Step 3. Press ALL button Learning selected destination EDID to all sources.

Step 4. Press ENTER button To conrm entries.

LEARNINGEDIDdenition Learning EDID from Destination to Source

1. Switcher will LEARN destination EDID and pass the selected source.

2. To set up learning between a single destination and single source: Press EDID button > Press Destination (1 thru 8) > Press Source (1 thru 8) > Press ENTER to conrm. Switcher will learn destination EDID to source device.

3. To set up learning between a single destination and Multiple sources: Press EDID button > Press Destination (1 thru 8) > Press the majority Sources (1 thru 8) > Press ENTER. Switcher will learn single destination EDID to many source devices.

4. How to Learning single destinations with all sources. Press EDID button > Press ALL button > Press ENTER to conrm.

EDID FUNCTION

EDID FUNCTION FOR HDMI MATRIX SWITCHER

EDID function : 8x Embedded EDID Modes

Mode 1. FSS

Mode 2. H24-3D (1080p-24 bits) Audio Support : PCM 2CH

Mode 3. H24-3D-M (1080p-24bits) Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH,

Mode 4. H36-3D (1080p-36 bits) Audio Support : PCM 2CH

(Fast Speed Start) Automatic capture of the most suitable EDID from Destination to Source.

DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH

Mode 5. H36-3D-M (1080p-36 bits) Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH,

DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH

Mode 6. 1280x1024-60Hz (DVI-D) DVI Support : DVI-D 1280x1024 60Hz

Mode 7. 1920x1200-60Hz (DVI-D) DVI Support : DVI-D 1920 x 1200 60Hz

Mode 8. AUTO <Default> All Outputs will be set to the highest common resolution of all connected display

devices.

TYPICAL APPLICATION

INSTALLING DIAGRAM

Sample connection using IR Transmitters (SB-101) and IR Receiver (SB-100) with SB-6335R & SB-5688CT-A to control a projector.

NOTE:

1. IR Control Projector Over HDBaseT™ Extender:

SB-5688CT-A HDBaseT™ Transmitter SB-6335R HDBaseT™ Receiver

2. Projector RS-232 Control by a PC via CATx TX.

3. Projector IR control via CATx IR in (IR To projector).

4. IR Extender Transmitter (SB-101): Use SB-101 IR Transmitter to Extend IR signal to Projector.

5. IR Extender Receiver (SB-100):

Use SB-100 IR Receiver to receive the Projector IR Remote signal.

TYPICAL APPLICATION

INSTALLING DIAGRAM

Sample connection using IR Transmitters (SB-101) with SB-5688CT-A and SB-6335R to control a IR signal from Satellite Receiver.

NOTE :

1. IR Control Satellite Receiver Over HDBaseT™

CAT5e/6/7 Extender from room:

SB-5688CT-A HDBaseT™ CATx(6/6a/7) Transmitter SB-6335R HDBaseT™ CATx(6/6a/7) Receiver

2. Destination RS-232 Control :

Via SB-5688CT-A TX RS-232 in.

3. IR Extender Transmitter (SB-101):

Use SB-101 IR Transmitter to Extend IR signal.

Support HDBaseT™ Extender by SB-6335T Transmitter and SB-6335R Receiver via CATX(6/6a/7) cable.

TYPICAL APPLICATION

INSTALLING DIAGRAM

Sample connection using Audio Extractor To Re-code Audio (SB-5609) or to control ARC (SB-5610) and Extend the HDMI signal via HDBaseT™ Transmitter to IR Receivers (SB-6335R) with SB-5688CT-A to extend 100M distance between switcher and destination.

NOTE :

1. Audio Extractor To Re-code Audio : SB-5609 HDMI Audio Extractor.

2. Control HDMI ARC: SB-5610 ARC Control Box.

3. Switcher RS-232 Control Via a PC.

4. Switcher IR External port : Via SB-100 IR Extender Receiver.

5. HDMI Display : Signal from Blu-Ray or HD Satellite Receiver.

Application HDBaseT™ IR, RS-232, Multi format Audio and HD Video signals to pass over CATX(6/6a/7) cable.

The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).

1. SB-100 IR 300M Receiver

Switcher IR EXT. In Cable (3C) IR Receiver (SB-100)

2. SB-100C IR 2M Receiver

Pin configuration for IR 984 feet (300M) Extender Receiver such as SB-100 compatible

IR EXTENDER

Distance: Max.300M

SB-100

IR Receiver Set

The SB-100 IR Receiver is required when using the port “ALL in” Jack.

IR Receiver cable 6ft (2M)

SB-100C

IR Receiver Cable

The SB-100C IR Receiver will not function on the port “ALL in” Jack.

*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***

R S- 232 IR E X T. i n

RS-232

IR EXT .

R oH S /95 /E C

INP UT

DC 12V

SB-100 Maximum Distance ~ 984 feet (300M)

Switcher IR EXT. In

Cable (2C) IR Receiver (SB-100C)

IR PN#: SW-XXXX

IR Rx

SB-100

Control Switch SB-XXXX

Distance: Max.(2M)

R oH S /95 /E C

INP UT

R S- 232 IR E X T. i n

RS-232

IR EXT .

DC 12V

SB-100C Maximum Distance ~ 6 feet (2M)

IR Rx

SB-100

IR PN#: SW-XXXX

-1

3 4

OWER

T -2

-3

N O

1 2 3 4

WIT

1 2

1 2 3

I MA

1 2 3

DM H

Control Switch SB-XXXX

-1

3 4

OWER

T -2

-3

N O

1 2 3 4

WIT

1 2

1 2 3

I MA

1 2 3

DM H

SW IR

Ring :VCC

Tip : Signa l

Tip

Ring

Sleeve

Sleeve: GND

SB-100

IR Receiver Set

Sleeve

Tip ( center)

SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)

Pin configuration for IR Receiver 6 feet (2M) cable such as SB-100C compatible

IR Receiver cable 6ft (2M)

SB-100C

IR Receiver Cable

Tip : Signal Ring: NC Sleeve: G ND

Tip

Ring

Sleeve

Ring

Sleeve

Tip ( center)

SB-100 Receiver and SB-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)

Note:

Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.

VCC (Rin g)

GND (Sle eve )

Signal ( cen ter )

GND (Sle eve )

Signal ( cen ter )

1. SB-101 IR 300M Transmitter

Device Cable (3C) IR Transmitter (SB-101)

The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).

2. SB-101C IR 2M Transmitter

IR EXTENDER

Ro H S /95 /E C

SB-101

IR Transmitter Set

IR Transmitter cable 6ft (2M)

Ro H S /95 /E C

SB-101C

Transmitter Cable

*** When you plug the External IR extender into the switcher, the front panel IR transmitter remains active. ***

PIN CONFIGURATION:

SB-101 and SB-101C Transmitter Pin configuration

DC 12V

IR out

From

Receiver

IR in

Receiver

CAT6/6a/7

OUTPUT

IR Tx

SB-101

SB-101 Maximum Distance ~ 984 feet (300M)

Device Cable (3C) IR Transmitter (SB-101C)

DC 12V

IR out

From

Receiver

IR in

Receiver

CAT6/6a/7

OUTPUT

IR Tx

SB-101C

SB-101C Maximum Distance ~ 6 feet (2M)

Tip : Signa l Ring :VCC

Tip

Ring

Sleeve

Sleeve: GND

SB-101

IR Transmitter Set

Sleeve

Tip ( center)

SB-101 Maximum Distance ~ 984 feet (300M)

IR Transmitter cable 6ft (2M)

Sleeve

Tip : Signal Ring: NC

Tip

Ring

Sleeve: G ND

SB-101C

Transmitter Cable

Sleeve

Tip ( center)

SB-101C Maximum Distance ~ 6 feet (2M)

Note:

Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.

VCC (Rin g)

GND (Sle eve )

Signal ( cen ter )

GND (Sle eve )

Signal ( cen ter )

ETHERNET & RS-232 SERIAL INTERFACE

ETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM VERSION COMPATIBLE V2.0

For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.

ETHERNET SERIAL INTERFACE

Pin Ethernet Reference

1 TXOP TX +

2 TXON TX -

3 RXIP RX +

4 NC

Note :

Control the switcher

SPD : Speed LINK : Ethernet link

RJ-45 Female 8P-8 Connector

ETHERNET TCP/IP PROTOCOL COMMANDS ( ETHERNET / RS-232 CONTROL DRIVER V2.0.1 )

*** The Ethernet port and RS-232 port cannot be used simultaneously. Any connection to the Ethernet Control port will disable

serial commands send to the RS-232 port.***

5 NC

6 RXIN RX -

7 NC

8 GND

RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0

For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual.

RS-232 SERIAL INTERFACE

Pin RS-232 Denition

1 -------- Not used

2 TX Transmitter

3 RX Receiver

4 -------- Not used

5 GND Ground

6 -------- Not used

7 -------- Not used

8 -------- Not used

9 -------- Not used

ETHERNET TCP/IP PROTOCOL COMMANDS ( ETHERNET / RS-232 CONTROL DRIVER V2.0.1 )

The switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system.

The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1. When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.

LIMITED WARRANTY

PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime, without notice to you.

RESTRICTIONS ON USE OF THE PRODUCT

It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.

The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product

are licensed to you by SHINYBOWUSA, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “SHINYBOWUSA”) for your

personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.

The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only. SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.

The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its ofces within the State of Texas, United States of America. SHINYBOWUSA

makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls. Disclaimers and Limitation of Liability

SHINYBOWUSA may change or modify the Product at any time, from time to time.

THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE.

SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.

TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY SHINYBOWUSA.

UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.

END OF DOCUMENT

122 Rose Ln. Suite 303

1-877-SHINY-USA 1-877-744-6987 1-972-377-2508

sales@shinybowusa.com

Frisco, Texas 75034

www.shinybowusa.com

Shinybow USA SB-5688CT-A Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual