P a rt N o. : E N C L 00 56 5 4 000 A0
Tha n k y ou fo r p urc ha s ing th e SB- 565 4 HDM I Distrib uto r A m p lifie r. Y o u w ill fi n d th is un it e a sy to in sta ll
a n d hig hly re lia b le b ut it is e sse ntia l tha t y ou re a d this m a n u a l thro ug hly b e fo re a tte m ptin g to u se
1x 4 HDM I Distrib utio n A m p li fie r.
H D MI D is tr ib ut io n A mpl i er S er ie s
1 x 4 HDM I D ISTRIBUTIO N AMPLIF IER
HIG H-D EF INI TIO N M U LTIM ED IA IN TE RF AC E
V E R S I O N L E V E L : V 1 . 3
MOD EL : SB -565 4
Instruction Manual
M U L T I M E D I A A U D I O A N D V I S U A L
SAFETY INFORMATION
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
1.
Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original
factory packing.
2.
Read all documentation before operating your equipment. Retain all documentation for future reference.
3. Follow all instructions printed on unit chassis for proper operation.
4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
5. Make sure power outlets conform to the power requirements listed on the back of the unit.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit
7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of
a piece of equipment is not defeated.
8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by
any warranty.
9.
Power down & disconnect unit from mains voltage before making connections.
10.
Never hold a power switch in the ＂ON＂ position.
11. Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices.
12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit,
13.
such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be
Periodically ＂blown free＂ of foreign matter.
14.
Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside.
15.
Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
16.
Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.
Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
from the appliance.
IMPORTANT SAFETY INSTRUCTIONS
To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference.
To reduce the risk of electric shock, do not remove the cover from the unit. No user serviceable parts inside. Refer servicing to qualified personnel.
To reduce the risk of fire, do not expose the unit to rain, water or excessive moisture.
Do not force switched or external connections.
When moving the unit disconnect the serial port connections first then the power cable and finally the interconnecting cables to other devices.
Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean dry cloth.
Installation of this unit should be in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
PAGE 3SB-5654 INSTRUCTION & OPERATION MANUAL
TABLE OF CONTENTS
3
4
5
6
7
INTRODUCTION
FRONT PANEL
REMOTE CONTROL
TABLE OF CONTENTS
8
9
TYPICAL APPLICATION
10
FEATURES & SPECIFICATIONS
REAR PANEL
LIMITED WARRANTY
This symbol is intended to alert the user to the presence of uninsulated
enclosure tha may be of sufficientmagnitude to constitue a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of important
operational and maintenance (serving) instructions in the literature
accompanying the appliance.
T prevent electric shock do not use this (polarised) plug with an o
extension cord, receptacle or other outlet unless the blades can
be fully inserted to prevent blade exposure.
T prevent electric shock, match wide blade of plug to wide slot, o
fully insert.
Caution:
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER
SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
T
I
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
of uninsulated “dangerous voltage” within the products enclosure that
POWER AND CONNECTIONS
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet.
The off state for this unit is called standby mode. In standby mode the unit is designed to consume
a reduced quantity of power compared to normal operating modes.
When not using the unit for a long period of time. Insure that the AC power cord is disconnected from
the wall outlet.
The AC wall outlet should be installed near to the unit and be easily accessible.
Do not plug in or attempt to operate an obviously damaged unit.
PAGE 4 SB-5654 INSTRUCTION & OPERATION MANUAL
PACKAGE CONTENTS
INSTRUCTION
1. Main console unit
2. Operating Instructions
3. IR Remote Controller (SW-5654)
4. 19 inch Ear mount pair
5. IR Extender receiver (SB-100)
6. Power Supply 12VDC, Universal Type 50/60Hz, 100~230 VAC
The SB-5654 is high quality HDMI distribution amplifier, HD high performance
designed to distribution HDMI signal. Providing I/O as following :
> 1x input : 1x HDMI (Digital Video-TMDS and Audio)
> 4x outputs : 4x HDMI (Digital Video-TMDS and Audio)
Automatic input/output HD signals detection:
> PC monitor from VGA to UXGA
> HDMI 480i To 1080p
> DVI 480i To 1080p
The distributor support data rates up to 2.25 Gbps. And enable 1080 p HDMI formats and
UXGA DVI resolution(1920x1200) to LCD and Plasma display applications.
Auto scan function software is built-in to extend HDMI signal for long distance.
This product is certified as beingfully HDMI and HDCP compliant.
This product is also RoHS, CE, FCC compliant. Support high HDMI (HDCP)
source to multiple HDMI (HDCP) displays, LCD monitors or HD projectors.
Before attempting to use this unit, please check the packaging and make certain
the following items are contained in the shipping carton :
Note :
Please retain the original packing material should the need ever arise to return the unit.
If you find any items are missing, contact your reseller or Shinybow immediately.
Have the model number, Serial Number and Invoice available for reference when you call.
INTRODUCTION
OPERATING THE UNIT
Once you have connected the distributor as described above, you must be
certain that the input are being fed appropriate signals and are not suffering
from signal loss due to cabling problems or problems with the source device.
If the input signals to the distributor are appropriate, switch the power switch
to <ON> and you should see and hear the signals on the devices you have
connected to the various output connectors of the distributor.
PAGE 5SB-5654 INSTRUCTION & OPERATION MANUAL
FEATURES & SPECIFICATIONS
FEATURES
SPECIFICATIONS
1. Type of Distributor : 1x4 HDMI Distribution Amplifier
2. Signal Supports :HDMI Standard, DVI and HDCP Compliant
3. Video Supported:1080p HDMI formats 1920x1200 and DVI UXGA HD resolutions.
4. Audio Supported : DTS-HD Master Audio, Dolby True -HD & Dolby Digital Plus
5. Type of Signal: TMDS Digital Video PCM Digital Audio
6. Compliant with HDMI standard: HDMI and HDCP.
7. HDTV Support: 1080p HDMI formats and UXGA 1600x1200 resolution.
8. Controls: IR Remote
9. Data Rates: 250Mbps to 2.25 Gbps. Pixel clocks: 25MHz to 225 MHz.
10. HDMI Cable Distance: 10 meters at 2.25Gbps.
11. Various video input interface supporting digital video standards such as:
• RGB/Y : 24/30/36-bits • YCBCR :8/10/12/16/20/24-bits
•Double data rate interface for RGB/YCBCR : 12/15/18-bits
12. Infrared frequency: 38KHz.
13. Safety Approvals: CE, FCC, RoHS(2002/95/EC).
14 .Dimensions : 11.97” x 5.90” x 1.73” (304mm x 150mm x 44mm)
15. Power Supply: DC12V/1A~2A (Full load Consumption Maximum 1.25A)
16. Unit Weight : 1.90 Kgs ( 3.16 Lb)
CBCR
1. Support 1x4 HDMI Distribution Amplifier
2. I/O Signals : HDMI with HDCP Digital Video and Digital Audio (PCM)
3. HDMI and HDCP compliant
4. Support link speeds of up to 2.25 Gbps (link clock rate of 225 MHZ)
5. Support wide range of PC resolutions from XGA to UXGA 1600x1200 and
HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p
6. Compatible with all HDMI devices, PC monitors, Plasma TV display and HDTV
7. Support Digital Video TMDS formats in Deep Color 12bits
8. Support colour depth of up to 36 bits and ensures robust transmission of
high-quality uncompressed video content, along with state-of-the-art
uncompressed and settop boxes.
9. Bi-direction colour space conversion(SCS) between RGB and YCBCR color
spaces with programmable coefficients.
10. Auto-Scan input and outputs status via LED display on front panel
11. Control by Selection buttons on front panel and use IR Remote Controller
12. Support desktop with Ear mount and 19 inch Rack mountable type panel
13. Power supply DC12Volt, Universal Type switch 100~230VAC, 50/60Hz
1x4 HDMI DISTRIBUTION AMPLIFIER
POWER
1 2 3 4
IRIR
PAGE 6 SB-5654 INSTRUCTION & OPERATION MANUAL
FRONT PANEL
2
1
4
POWER ON SWITCH
IR SENSOR
1
3
The power switch turns the unit on and off.
The LED will illuminate red to indicate
that the switcher is ON and is receiving power
INPUT SOURCES STATUS DISPLAY
2
Input source 1 to 4 LED illuminates blue to indicate
that a video source is present on that input.
The IR sensor receives IR commands from the
supplied remote controller.
19 INCH EAR MOUNT PAIR
4
19 inch case Ear Mount pair
Part number : 1U-300L
FRONT PANEL
CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal input-output, Power requirements
plus any controls present.
Before using the distributor, please take the time to make certain that the device you wish to connect to its inputs
is functioning properly in all respects. Verify that the video and audio signals are present and are being displayed
properly on a suitable device.
If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s)
of the distributor to the carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor,
connect the DC connector to the distributor first and then plug the adaptor into a functional AC outlet.
3
SB-5654
DC 12V
INPUT
INPUT
OUTPUT- 1
HDMIHDMI
OUTPUT- 2
HDMI
OUTPUT- 3
HDMI
OUTPUT- 4
HDMI
RoHS/95/EC
PAGE 7SB-5654 INSTRUCTION & OPERATION MANUAL
1
REAR PANEL
REAR PANEL
2
1
INPUT - 1x HDMI
2
Input 1 - HDMI Digital Video/Audio, Connector with fix screw
DC POWER INLET
The distributor is fitted with a DC power plug-park
input connector. Please ensure that the plug-park
used is of an approved type and is of sufficient
current carrying capacity with the correct voltage
and connector polarity. 12Volt DC power supply
1A~2A Max.
3
OUTPUTS - 1,2,3,4 HDMI
Output 1 - HDMI Digital Video/Audio, Connector with fix screw
Output 2 - HDMI Digital Video/Audio, Connector with fix screw
Output 3 - HDMI Digital Video/Audio, Connector with fix screw
Output 4 - HDMI Digital Video/Audio, Connector with fix screw
HDMI digital video/audio connector:
HDMI Female connector.
Connect a signal link of HDMI direct digital video/audio to
this Female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources.
Note:
With the proper adapters, the distributor
can be used with DVI digital video signals
HDCP compliant.
Connect a signal link of HDMI direct digital video/audio to
this Female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources.
HDMI digital video/audio connector:
HDMI Female connector.
Note:
With the proper adapters, the distributor
can be used with DVI digital video signals
HDCP compliant.
Power Jack:
DC Jack - inner OD O 2.1mm (+ )
Outside OD O 5.5mm (GND)
Power input - 12VDC, 1A~2A
3
10
POWERPOWER
1x4 HDMI DISTRIBUTION1x4 HDMI DISTRIBUTION
ONON OFFOFF
0F
PAGE 8 SB-5654 INSTRUCTION & OPERATION MANUAL
Before making any connections to the SB-5654. Observe the following:
> Ensure the mains voltage supply matches the label on the supplied plug-
Pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a common point.
> Avoid powering equipment within a system from multiple power sources
that may be separated by large distances
REMOTE CONTROL
REMOTE CONTROL
> Connect all audio video sources and destination equipment
> power up all source and destination audio-visual sources
> For each destination output select the appropriate input source by using
> Upon power up the distributor will return to its last used setting before
The front panel supplied IR remote control.
Powered down.
SWITCH POWER ON or OFF
1
Controller with a separate power ON and OFF
2
2
1
CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal input-output, Power requirements plus any controls
present.
Before using the switcher, please take the time to make certain that the device you wish to connect to its inputs is functioning
properly in all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device.
If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s) of the switcher to
the carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor, connect the DC connector to the switcher
first and then plug the adaptor into a functional AC outlet.
TYPICAL APPLICATION
INSTALLING
INPUT PORT SIGNAL :
1. HDMI - HDMI connector with fix screw
OUTPUTS PORT SIGNALS :
SB-5654 SUPPORT ONE HDMI INPUT TO FOUR HDMI DISTRIBUTOR OUTPUTS
SUPPORT IR REMOTE CONTROL
1. HDMI - HDMI connector with fix screw
2. HDMI - HDMI connector with fix screw
3. HDMI - HDMI connector with fix screw
4. HDMI - HDMI connector with fix screw
SHINYBOW
SB-5654
1x HDMI source to 4 x HDMI displays Distribution Amplifier
HD MI DI SPL AYs
1 -
2 -
3 -
4 -
OU T PU T
IN P UT
HD MI Pl aye r
D
V
D
PAGE 9SB-5654 INSTRUCTION & OPERATION MANUAL
LIMITED WARRANTY
SHINYBOW WARRANTY
SHINYBOW Technology warrants this product against defects in materials and workman
ship for a period of 1 year from the date of purchase.
Should this product, in SHINYBOW Technology,s opinion, Prove defective within this
warranty period, SHINYBOW Technology, at its option, repair this product without charge,
to whatever extent it shall deem necessary to restore said product to proper operation
condition.
This warranty does not apply if the fault has been caused by misuse, improper handling
care, electrical or mechanical abuse, and abnormal operating condition or non-SHINYBOW
Technology authorized modification to the product.
If repairs are necessary under the warranty policy, the original purchaser must return the
product to local distributor, freight prepaid.
After repairs are complete, the product will be returned.
REGULATORY COMPLIANCE
The product complies with the relevant standards for CE, FCC and RoHS approval.
The power Adaptor/Supply has been tested for compliance with UL.CAS and CE standards.
TROUBLESHOOTING
If you experience a <no signal> with this switcher or distributor outputs, first make certain that
the signal being fed to its inputs is acceptable.
Disconnect the cables from the this switcher or distributor inputs and connect them directly to
an appropriate monitoring device, if you do not see or hear a signal the problem may well be
he signal source itself. Also check that the AC outlet you have used to power the switcher or
distributor is actually providing power as a wall switch often controls an AC outlet.
The second most common problem with this switcher or distributor revolves around the cables,
Inspect the cables for loose connectors or cable damage such as crushed cable or cables with
cuts or nicks. Replace any cable exhibiting these problem.
You also must use the highest quality cables if you want to achieve the best results. Poor quality
cables will provide poor quality signals.
PAGE 10 SB-5654 INSTRUCTION & OPERATION MANUAL
M U L T I M E D I A A U D I O A N D V I S U A L
1399 Wildfire Lane | Frisco, TX 75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508
sales@shinybowusa.com
www.shinybowusa.com
Loading...