MULTIMEDIA AUDIO AND VISUAL
MODEL : SB-5588LCM
8x8 Component/Audio Matrix Switcher
8x8 Component/Audio Matrix Switcher
INSTRUCTION MANUAL
HDMI Matrix Switcher Series
Thank you for purchasing the SB-5588LCM 8x8 Component-Audio Matrix Switcher. You will fi nd this unit easy
to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 8x8
Component-Audio Matrix switcher.
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fi re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
fl ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualifi ed service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports fi rst, then remove the power cable; fi nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifi er service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
TABLE OF CONTENTS
CONTENTS
INTRODUCTION ...............................................................1
FEATURES & SPECIFICATIONS ....................................2
FRONT PANEL ................................................................3
REAR PANEL ...................................................................6
REMOTE CONTROL ......................................................7
RS-232 SERIAL INTERFACE ...........................................9
TYPICAL APPLICATION ................................................10
IR EXTENDER ................................................................11
LIMITED WARRANTY .....................................................12
INTRODUCTION
Congratulations on your purchase today one of the most innovative
Component/Digital/Audio matrix switching products on the market
today. The SB-5588LCM is a true Matrix Routing Switcher for
Component Video, Digital and Stereo Audio signals. It is a 8
individual Component inputs with 8 individual Component outputs.
Because it is a matrix router, any input may be routed to any output;
or the same input may be routed to all outputs or any combination.
It completely eliminates the need to constantly move around
audio and video input and output cables. The SB-5588LCM is
useful for Matrix signals from AV source devices (such as: VCRs,
Camcorders, Video Game Consoles, Video CDs, DVDs, Satellite
Receivers, CAT5 Set Top Boxes, etc.) to AV destination devices
(such as: LCD TV, HDTV, Plasma displays, Projectors, etc.).
Selection of inputs is made via the Front Panel push buttons or an
Infrared Remote Control unit or RS-232 control by computer
PACKAGE CONTENTS
Check that you have the following components;
• SB-5588LCM Matrix Switcher
• IR Remote control
• RS-232 Software (All Windows Operating Systems)
• Rack Mounts
• IR Extender receiver
• RS-232 Cable
• Users Guide
• AC/DC Adapter: 12VDC, 2A Universal Type 50/60Hz,
100~230 VAC
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fi re,
electrical shock and injury to persons.
• To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for suffi cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer fi le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 1.2 OCT 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
1
FEATURES & SPECIFICATIONS
FEATURES
• Supports 8x inputs to 8x outputs Component Video(YPBPR) Matrix Switcher
• Input/Output signals via Component Video(YPBPR), SPDIF (PCM), Stereo Audio(AR/AL)
• Higher Video Bandwidth 325MB each path signals.
• Supported HDTV high defi nition resolutions 408p, 576i/p, 720p, 1080i/1080p
• SPDIF digital Audio (PCM) and Composite Video compliant
• Compatible with all Component Video devices, Plasma TV display and HDTV
• Supported RS-232 serial interface protocol commands list
• Control PC RS-232 Drive compatible with win-95/98/2000/xp
• Various User Interface controls:
• Attached Window based control software for Desktop or NB control by RS-232 port
• Manual controlled by Front Panel button
• IR remote control
• Support desktop with Ear mount and 19 inch Rack mountable type panel
• Power supply DC 12Volt, Universal Type Switch 100~230VA C, 50/60Hz
SPECIFICATIONS
• Type of Switcher: 8 in to 8 out, Component Video-Digital-Audio Matrix Switcher
• I/O Signals: Component Video (YPBPR) 0.5~1.0Vpp, DDC 5Vpp, SPDIF digital Audio (PCM), Via 1x RCA connector, Stereo Audio
(AR/AL), Via 2x RCA connector(Re d/white)
• Video Bandwidth: 325MHz (-3db), 200mVp-p
• Video Supported: Higher resolution formats 480i/p, 720p & 1080i/p
• Audio Supported: SPDIF digital Audio (PCM) and Stereo Audio(AR/AL)
• Low All Hostile Crosstalk: -83 db@5 MHz
• Controls: IR remote, Select buttons on the front panel & RS-232
• PC RS-232 Control: RS-232 interface serial via DRV on a PC
• Gain control: 60MHz 0.1 db gain fl atness
• Chassis Material: Metal (T=1mm)
• Safety Approvals: CE, FCC, Ro HS(2002/95/EC)
• Dimensions (LxWxH): 19 x 7.87 x 3.46 in (482mm x 200mm x 88mm)
• Power Supply: DC12V / 2A (consumption 1.6A Max) Use Universal Switch Type 50/60Hz,100~230 VA C
• Product Weight: 3.25 Kgs / 5.42 lbs
As product improvements are continuous, specifi cations are subject to change without notice.
2
FRONT PANEL
FRONT PANEL
1. POWER SWITCH
The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The
switcher will remember that last state during a power cycle. When power is removed and resorted, the last confi guration will be evoked.
2. INPUT STATUS DISPLAY
Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input.
3. OUTPUT STATUS DISPLAY
Each Output (destination) Channel shows which input (source) is assigned.
4. DESTINATION SELECT BUTTONS
Separate outputs 1 thru 8 select buttons are provided for each destination assignment.Routing can be Source to Destination or one
source to multiple destinations.
Example : Press Destination 1, 3, 5 then press Source 2 will route Input 2 to Output 1, 3, 5 respectfully.
5. SOURCE SELECT BUTTONS
Separate inputs 1 thru 8 select buttons are provided each source selection.
6. IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
7. 19 INCH EAR MOUNT PAIR
Converts desk-top to 19 inch rack mount bracket (part # 2U-440L) INCLUDED. Image shows rack mount bracket attached.
3
FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - OFF
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected.
10. FUNCTION KEY - RECALL
The system will show previously stored presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- press RECALL button.
- press 1 thru 8 on either Source or Destination row.
- press ENTER The pre-set confi guration will execute.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
11. FUNCTION KEY - ENTER
Press ENTER to confi rm entries.
4
FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - MEMORY
The system will show store presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Confi gure desired matrices..
- Press MEMORY button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
13. FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
14. 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED. Image shows rack mount bracket attached.
5
REAR PANEL
REAR PANEL
1. DC POWER INLET
The Switcher is fi tted with a DC power plug input connector.Ensure
that the used is of an approved type and is of suffi cient current
carrying capacity with the correct voltage and connector polarity.
12Volt DC power supply 2A Max.
2. IR EXTENDER CONTROL
Support one of IR Extender (IR input)
Extend distance maximum 1000 ft. / 300M
Power Jack:
DC Jack - Inner OD ᴓ 2.1mm (+ )
Outside OD ᴓ 5.5mm (GND)
Power input - 12VDC, 2A
IR Extender Jack:
Female Jack - inner OD O 3.5 mm
3. RS-232 CONNECTION
RS-232 control port to allow for interfacing to a PC Such as a
computer or touch panel control, to the switcher via this DB-9pin
Female connector for serial RS-232 control.
4. INPUTS-1~8 COMPONENT-DIGITAL-AUDIO
Connect a signal source of Component Video (YPBPR)/ digital
Audio (PCM)/Stereo Audio devise to 8:8 switcher.
Input 1~8 port source signals :
- Component Video (YPBPR), 3x RCA Connectors
- SPDIG : Digital Audio (PCM), 1x RCA Connector
- Stereo Audio (AR/AL), 2x RCA Connectors
5. OUTPUTS-1~8 COMPONENT-DIGITAL-AUDIO
Connect a signal of Component Video (YPBPR), digital video &
audio direct to Female RCA connector. This connector supports
component video, digital video & audio to HDTV display device.
Output 1~8 display port signals :
- Component Video (YPBPR), 3x RCA Connectors
- SPDIF : Digital Audio (PCM), 1x RCA Connector
- Stereo Audio (AR/AL), 2x RCA Connectors
Remote port :
DB-9pin Female connector
Component Video (YPBPR) Via 3x RCAs
SPDIF: Digital Audio(PCM) Via 1x RCA connector
Stereo Audio(AR/AL) Via 2x RCA connectors
Note: With 6x RCA female connectors
Component Video (YPBPR) Via 3x RCAs
SPDIF : Digital Audio(PCM) Via 1x RCA connector
Stereo Audio(AR/AL) Via 2x RCA connectors
Note: With 6x RCA female connectors.
6
REMOTE CONTROL
Before making any connections to the SB-5588LCM. Observe the following:
> Ensure the mains voltage supply matches the label on the
supplied plug- Pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a
common point.
> Avoid powering equipment within a system from multiple
power sources that may be separated by large distances
REMOTE CONTROL
1. & 2. SWITCH POWER ON or OFF:
Controller with a power ON and OFF
3. DESTINATION : 1 thru 8 OUTPUT SELECTION:
Press the destination button to select the output display channel.
4. SOURCE : 1 thru 8 INPUT SOURCE SELECTION:
Press input 1~8 sources with selection button
5. FUNCTION KEY:
ALL - function selection button
OFF - function selection button
RECALL - function selection button
DEMO or ENTER - function selection button
MEMORY - function selection button
LOCK - function selection button
> Connect all audio video sources and destination equipment
> Power up all source and destination audio-visual sources
>For each destination output select the appropriate input source
by using the front panel input 1~8 select buttons. The supplied
IR remote control. Or through the RS-232 serial communications port.
> Upon power up the switcher will return to its last used setting
before Powered down.
7
REMOTE CONTROL
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES
CUSTOM CODE : 37C8
DATA CODE :
POWER ON : 37C8 A15E
POWER OFF : 37C8 A25D
ALL : 37C8 B04F
OFF : 37C8 B14E
EDID : 37C8 B748
LOCK : 37C8 B54A
RECALL : 37C8 B24D
MEMORY : 37C8 B44B
ENTER : 37C8 B34C
PRESS DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 37C8 10EF
DESTINATION #2 : 37C8 20DF
DESTINATION #3 : 37C8 30CF
DESTINATION #4 : 37C8 40BF
DESTINATION #5 : 37C8 50AF
DESTINATION #6 : 37C8 609F
DESTINATION #7 : 37C8 708F
DESTINATION #8 : 37C8 807F
SOURCE #1 : 37C8 01FE
SOURCE #2 : 37C8 02FD
SOURCE #3 : 37C8 03FC
SOURCE #4 : 37C8 04FB
SOURCE #5 : 37C8 05FA
SOURCE #6 : 37C8 06F9
SOURCE #7 : 37C8 07F8
SOURCE #8 : 37C8 08F7
For example:
Select Destination # 1 to show Source #1~8,
The IR Data Code list when press Destination # then press Source #
The IR Data Code list :
Destination # 1, Source #1 37C8 10EF 37C8 01FE
Destination # 1, Source #2 37C8 10EF 37C8 02FD
Destination # 1, Source #3 37C8 10EF 37C8 03FC
Destination # 1, Source #4 37C8 10EF 37C8 04FB
Destination # 1, Source #5 37C8 10EF 37C8 05FA
Destination # 1, Source #6 37C8 10EF 37C8 06F9
Destination # 1, Source #7 37C8 10EF 37C8 07F8
Destination # 1, Source #8 37C8 10EF 37C8 08F7
8
RS-232 SERIAL INTERFACE
RS-232 SERIAL INTERF ACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPA TIBLE V2.0.1
RS-232 SERIAL INTERFACE
Pin RS-232 Defi nition
1 -------- Not used
2 TX Transmitter
3 RX Receiver
4 -------- Not used
5 GND Ground
6 -------- Not used
7 -------- Not used
8 -------- Not used
9 -------- Not used
RS-232 PROTOCOL COMMANDS ( RS-232 Control driver V2.0.1 )
The Shinybow switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control
system.
The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1.
When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
9
TYPICAL APPLICATION
8X COMPONENT SOURCES TO 8X COMPONENT OUTPUT MATRIX SWITCHER
INSTALLING
CONTROL PORTS :
1. IR REMOTE - IR Remote Controller
2. RS-232 Interface - RS-232 interface system
INPUTS 1 ~ 8 PORT HD SOURCE SIGNALS :
COMPONENT VIDEO - Component Video(YPBPR), connector with RCA
SPDIF - Digital Audio(PCM), connector with RCA
AUDIO - Stereo Audio (AR/AL), connector with RCA
OUTPUT 1 ~ 8 PORT HDTV DISPLAY SIGNALS :
COMPONENT VIDEO - Component Video(YPBPR), connector with RCA
SPDIF - Digital Audio(PCM), connector with RCA
AUDIO - Stereo Audio (AR/AL), connector with RCA
SB-5588LCM SUPPORT COMPONENT EIGHT INPUTS MATRIX TO EIGHT SWITCH OUTPUTS
SUPPORT CONTROL IR & RS-232 INTERFACE SYSTEM PORTS.
10
IR EXTENDER
REAR PANEL IR EXTENDER PORT
SHINYBOW SB-5588LCM
IR Extender to a Room
IR part number : SW-5588
IR Receiver : SB-100 (included)
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
IR EXTENDER PACKAGE :
HOW TO SETUP THE IR EXTENDER COMPONENTS
11
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTW ARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its affi liates, including any manufacturers or distributors of the Product (collectively , “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its offi ces within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENT A TIONS REGARDING THE USE OR THE RESUL TS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT W ARRANT THA T THE FUNCTIONS PERT AINING TO THE PRODUCT WILL BE ERROR-FREE, THA T DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERT AINING THERET O ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOTSHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BYSHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THA T RESUL T FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IFSHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
12
MULTIMEDIA AUDIO AND VISUAL
1399 Wildfi re Lane | Frisco, TX 75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com
www.shinybowusa.com
Loading...