MULTIMEDIA AUDIO AND VISUAL
MODEL : SB-5430
4x2 Composite Video/S-Video Routing Switch
Composite Video/S-Video Switcher
INSTRUCTION MANUAL
Composite Video/S-Video Switcher Series
Thank you for purchasing the SB-5430 Composite Video I S-Video Routing Switcher. You will fi nd this unit easy
to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this
switcher.
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fi re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
fl ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualifi ed service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports fi rst, then remove the power cable; fi nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifi er service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
EN 55013 / EN 55020
FCC 47 CFR/Part 15 Subpart B
TABLE OF CONTENTS
CONTENTS
INTRODUCTION ...............................................................1
FEATURES & SPECIFICATIONS ....................................2
TYPICAL HOOK-UP & OPERATION ................................3
LIMITED WARRANTY ......................................................4
INTRODUCTION
Congratulations on your purchase of one of the most innovative
Video/Audio switching products on the market today. This Routing
Switcher is controlled by an IR Remote Controller and has 4
individual Composite Video or S-Video(Y/C)/Stereo Audio (R/L)
inputs with 2 identical Composite/S-Video/Audio outputs. It is
useful for routing signals from Composite/S-Video/Audio Source
devices (such as: VCRs, Camcorders, Video Game Consoles,
Video CD players, DVD players, Satellite Receivers, CA T5 Set Top
Boxes, etc.) to Composite/S-Video/Audio destination devices(such
as :VCRs, DVD recorders, TV Sets, Video Projectors, etc.)
This device can be operated in two modes: IR Remote control or
Manual mode. It can be selected by pushing the IR key/Manual
button on the front panel to the Video switcher. If you have four
devices hooked up to the four inputs and only one has its power
turned on, only that device can be switched to the output by IR
Remote control. When Manual mode is selected, same can be
done by pushing the Video select buttons on the front panel.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fi re,
electrical shock and injury to persons.
• To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for suffi cient space for air to circulate around the unit.
DISCLAIMERS
PACKAGE CONTENTS
Check that you have the following components;
• SB-5430 Routing Switcher
• Users Guide
• AC/DC Adapter: 12VDC, @ 300mA
AC/DC Adaptor Types : CE/UL/SAA/BS
CONFORMANCE TEST REPORT
FOR
REPORT NUMBER: ET93S-09-213-01
FOR
EN 55013 / EN 55020
FCC 47 CFR/Part 15 Subpart B
Report Number: ET93S-09-213-02
Model Number: SB-5430
Comment Number :
SB-3680, SB-3681, SB-3682, SB-5430, SB-5440, S8·5450,
S8·5460, S8·5470
Input: Audio/Video system (Composite or S-Video)
Stereo Audio system (R/L)
Output: Audio/Video system (Composite or S-Video)
Stereo Audio system (R/L)
Power Input: +DC12V, @ 300mA
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer fi le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 1.2 SEPT 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
1
FEATURES & SPECIFICATIONS
FEATURES
• 4 Inputs: Composite/S-Video/Audio (RCA)
• 2 Outputs: Composite/S-Video/Audio (RCA)
• IR and Menu double select
• Video Bandwidth 100Mhz
• Video Distortion 1.2db
• Audio Distortion 0.6db
• Channel Isolation 50db
• S/N Ratio > 50db
• Use IR Remote Controller (Frequency 38KHz)
• Support Lower power consumed full load under 250 mA
SPECIFICATIONS
• Video Inputs:
• 4 x Composite 0.5-2 Vpp, 75 Ohms, RCA Socket
• 4 x S-Video (Y/C) 75 Ohms, Mini-Din 4P Socket
• Audio Inputs: 4 x Stereo Audio: L+R 5Vpp, 47k Ohms. RCA socket
• Video Outputs:
• 2 x Composite 1 Vpp, 75 Ohms, RCA Socket
• 2 x S-Video (Y/C) 75 Ohms, Mini-Din 4P Socket
• Audio Outputs: 2 x Stereo Audio: L+R 5Vpp, 47k Ohms. RCA socket
• Video Bandwidth: 30Mhz, Maximum >100MHz. +/- 3db
• Video Distortion: <1.2db
• Audio Distortion: <0.6db
• Channel Isolation: >50db
• Signal to Noise Ratio: >50db
• Power Consumption: +12V DC@ ~250mA
• Power Source: 12V AC to DC Adapter
FEATURES OF THE CV/SV ROUTING SWITCHER
This device can be operated in two modes: IR Remote control or Manual mode. It can be selected by pushing the IR key/Manual button
on the front panel to the Video switcher. If you have four devices hooked up to the four inputs and only one has its power turned on, only
that device can be switched to the output by IR Remote control. When Manual mode is selected, same can be done by pushing the Video
select buttons on the front panel.
SINGLE SOURCE OPERATION
When only one source device, such as a VCR, is connected, always connect the device to the CV/SV Switcher’s AV1 input. Because AV1
is the default input, it will automatically be fed to the AV outputs when the CV/SV Switcher’s power plug is pulled out of the switcher. All of
video in/output selections will remain in switchers memory for as long as the power plug stays in the switcher. When the CV/SV switchers
power button is turned off It will not reset any settings.
DUAL OUTPUTS
Both of the CV/SV outputs will have the same signal that has been selected by internal switching logic of CV/SV Switcher. These dual
outputs are provided for convenience.
As product improvements are continuous, specifi cations are subject to change without notice.
2
SB-5430
TYPICAL HOOKUP AND OPERATION
Front View:
Power SW: ON/OFF
IR: Remote Controller receiver
Video Select: Video 1~4 Buttons
Rear View:
Input : 4 x Composite/S-Video/Audio
Output: 2 x Composite/S-Video/Audio
Power DC Input : DC12V, @ ~ 250mA
Safeguards and Precautions
A. Keep this unit away from fi re, extremely hot areas, water or moisture of any kind.
B. Do not place this unit on any support that is not fi rm, level and strong.
C. Do not service the unit yourself. Opening the unit’s housing will void the warranty.
D. Servicing must be by Shinybow or by an authorized technician.
C. Illegal duplication of copyrighted material is strictly prohibited by Federal Laws.
4x2 Composite/ S-Video(Y/C) Video Switcher
Applications: VCR, Video CD, DVD Player
3
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTW ARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its affi liates, including any manufacturers or distributors of the Product (collectively , “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its offi ces within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENT A TIONS REGARDING THE USE OR THE RESUL TS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT W ARRANT THA T THE FUNCTIONS PERT AINING TO THE PRODUCT WILL BE ERROR-FREE, THA T DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERT AINING THERET O ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOTSHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BYSHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THA T RESUL T FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IFSHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
4
MULTIMEDIA AUDIO AND VISUAL
122 Rose Ln. Suite 303 | Frisco, Texas 75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com
www.shinybowusa.com
Loading...