MULTIMEDIA AUDIO AND VISUAL
MODEL : SB-3879
HDMI Video Scaler
7x2 (mirrored) Multi Format HDMI Video Scaler Selector Switch
7 In’s Converted to VGA & HDMI Output
INSTRUCTION MANUAL
HDMI Video Scaler
HDTV Distribution Amplifi er Series
Thank you for purchasing the SB-3879 HDMI Video Scaler. Y ou will fi nd this unit easy to install and highly reliable
but it is essential that you read this manual thoroughly before attempting to use this HDMI Video Scaler.
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fi re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
fl ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualifi ed service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports fi rst, then remove the power cable; fi nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifi er service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
TABLE OF CONTENTS
CONTENTS
INTRODUCTION ...............................................................1
FEATURES .........................................................................2
SPECIFICATIONS .............................................................3
FRONT PANEL .................................................................4
REAR PANEL ..................................................................5
REMOTE CONTROL ........................................................8
IR CODES .........................................................................9
IR EXTENDER .................................................................10
TYPICAL APPLICATION .................................................11
RESOLUTION SUPPORT ...............................................12
VIDEO TIMING LIST ......................................................16
OSD OPTIONS OVERVIEW ............................................20
LIMITED WARRANTY .................................................... 26
INTRODUCTION
Congratulations on your purchase of a professional highperformance scaler and thank you for your support of ShinybowUSA
products. The SB-3879 is a video graphics scaler that accepts
seven types of signals: analog video, S-Video, component video,
VGA, DVI, HDMI, and display port signals.
It scales the input signals into either VGA or HDMI signals,
supporting higher full HD resolutions of 480i/p, 720p, 1080i/p.
Designed to solve problems of compatibility between source
devices and monitors, it is also useful for delivering one single
image on a TV wall. In addition to the front panel buttons and the
IR remote control, users may gain control over the SB-3879 using
a PC through the RS-232 serial port or Ethernet port.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fi re,
electrical shock and injury to persons.
• To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for suffi cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
PACKAGE CONTENTS
Check that you have the following components;
• SB-3879 Video Scaler
• IR Remote Control
• Rack Mounts
• IR extender receiver
• RS-232 driver CD (All Windows Operating Systems)
• RS-232 cable
• Users Guide
• AC/DC Adapter: 12 VDC, 2A universal type switch 50/60Hz,
100~230 VAC
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer fi le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 1.2 SEPT 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
1
FEATURES
FEATURES
• Supports HDMI 1.4a 30 formals and suits HDMI V1.4 transmitter & receiver
• Compliant with HDMI 1.4, DVI 2.0, and HDCP 2.0
• Input support:
• Analog: analog video, S-Video, composite video, VGA
• Digital: DVI, HDMI and display port (2560x1600)
• Output support: VGA and HDMI 1080p with deep color 36-bit
• Output audio support: S/PDIF, stereo audio
• Advanced 30 de-interlace, smooth edge algorithm and 3:2/2:2 fi lm mode processing
• 3D format functions: frame packing, side-by-side, top/bottom adjustment
• Bypasses XGA & 720p 120Hz 3D signal for DLP link 3D ready projector for active 3D display
• Supports full HD @24Hz, full HD 3D signal, with special algorithm for RH/LH synchronization
• Supports wide range of HD resolutions ranging from XGA to WUXGA 1920x1200 to
• HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p
• Compatible with all HDMI source devices, PC monitors, plasma HD display, HDTV and audio receivers/amplifi ers
• Supports intelligent color adjustment (discrete RGB color adjustment, hue, saturation, sharpness, contrast, brightness, and preset
color modes)
• Rack mountable: 19-inch ear rack mount
• Various user interface control:
• Windows-based GUI control via RS-232 port
• Front panel push buttons, IR wireless remote control, Third party RS-232 controller (via simple ASCII), Ethernet
• Supports IR extender with maximum extend distance reaching 1000 feet / 300 meters
• Supports TV wall function, allowing the image to be divided on multiple displays/monitors
• Power supply DC 12V, universal type switch, 100-240 VAC, 50/50Hz
2
SPECIFICATIONS
SPECIFICATIONS
Scaler Type: 7 in 2 out HDMI Video Scaler
Video Input Signal: 1x Composite / 1x S-Video /1x Component / 1x VGA / 1x DVI / 1x HDMI / 1x DP
Audio Input Signal: Digital Audio (PCM), Stereo Audio
Video Output Signal: 1x RGB, 1x HDMI
Audio Output Signal: 1x S/PDIF Digital Audio, 1x Analog, Audio RH/LH, 1x HDMI Audio
3D Support: 3D Video Format in HDMI 1.4a (225MHz)
Input Resolution: Up to 1080p-60, 1920x1200, and DP 2560x1600
Output Resolution: Up to 1080p-60 and 1920x1200
Source Status: Automatic scanning of input/output status
HDCP Support: DVI/ HDMI/ Display Port, compliant with HDCP 2.0
HDMI Compliance: HDMI 1.4a receiver and transmitter
HDMI Cable Distance: Max. ~ 50 feet (15 meters), depending on cable quality
Infrared Frequency: 38KHz
Chassis Material: Metal
IR Extend Distance: ~1000 feet (300 meters) line cable via IR extender
Control: IR remote control, RS-232, front panel push buttons
Dimensions: 11.96 x 5.90 x 1.73 in (304x150x11mm)
Rack Mount: 19-inch panel type (1U-44L)
Power Supply: Input 100 ~ 240 VAC, 50/60 Hz / Output DC 12V, 3A
Safety Approvals: CE, FCC, RoHS (2002/95/EC)
Temperature: 32 ° F ~ 100 ° F (0 ° ~32 ° C)
Shipping Weight: 2.05 Kgs / 3.42 lbs
Video Wall:
• Magnify, scroll, pan through all inputs
• Video wall function: Image split, cropping, and assign display location
• Pixel based overlap adjustment in all edges, up to 15x15 matrix displays
• Up to 2560x1600 input resolution via display port
System Control:
• Box ID for easy independent control through IR, RS-232, and 5 selectable profi le settings for dif ference display
• Ethernet control module with RJ45 connector
• Code update through RS-232
• ASCII control protocol over RS-232 and Ethernet
• One DC 12V/1A trigger output
Advanced Video Processing:
• Advanced 3D de-interlace, smooth edge algorithm and 3:2/2:2 fi lm mode
• High quality video and graphics scaling up and down
• Frame rate conversion
Intelligent Color Adjustment:
• Discrete RGB, color adjustment, hue, saturation, sharpness, contrast, brightness, 4 preset color modes
3D Function:
• Auto detect standard 3D signal (with 3D index inside) from Blu-ray DVD or STB
• Supports full HD @ 24 Hz full HD 3D signal with special algorithm for RH/LH synchronization
• Bypass XGA & 720p 120 Hz 3D signal for DLP link
• 3D ready projector for active 3D display
As product improvements are continuous, specifi cations are subject to change without notice.
3
FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH
The power switch turns the unit on and off. The LED will illuminate blue 10 indicate the switcher is ON and receiving power . The scaler will
remember the last setting during a power cycle. When turned on again, it will automatically apply the setting last used.
2. MENU
Press menu to open the On-Screen Display interface. Press again to exit menu
3. ENTER
Press enter to confi rm your entries.
4. ARROW KEYS
Use the arrow keys to move between the On-Screen Display options. Press the up key to enter the upper layer and the down key to enter
the next layer. Press the left and right keys to select options in the same layer or change the value of a parameter.
5. IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or a third party IR remitter.
6. OUTPUT SELECT BUTTONS
Select the desired resolution supported by your display devices. Press OTHERS for resolutions other than XGA, WXGA, 720p, 1080p.
The button will illuminate blue to indicate it is selected. Advanced resolution adjustment can be found in the OSD options.
7. INPUT SELECT BUTTONS
Select from one of the 7 buttons the video signal you intend to be scaled. The button will illuminate blue to indicate it is selected.
4
REAR PANEL
REAR PANEL
1. DC POWER INLET
The scaler suits a DC power plug-pack input connector. Please ensure
the plug-pack used is of an approved type and of correct current, voltage
output, and connector polarity. DV 12 Volt, power supply 2A.
2. ETHERNET CONNECTION
Connect a CATS cable to the Ethernet port for control of the scaler from
a computer.
3. RS-232 CONNECTION
Connect a serial cable to the RS-232 port for control at the scaler from a
computer.
4. LINK
Connect the link port for fi rmware updates. Used for testing purpose.
5. IR EXTENDER CONTROL
Supports remote control via IR extender. Maximum extend distance
reaches 1000 feet (300 meters).
Power Jack:
DC Jack - Inner OD O 2.1mm (+ )
Outside OD O 5.5mm (GND)
Power input - 12VDC, 2A
SPSC / RJ 45 connector
D-SUB 9-pin female connector
Terminal block connector
IR Extender Jack:
Female Jack - inner OD 0 3.5 mm
5
REAR PANEL
REAR PANEL
6. YPBPR + AR / AL AUDIO INPUT
Connect a signal of component video directly to the female RCA
connector, which supports component video (YPBPR) to HDTV
display devices. Connect the output port of your source audio
device to the AR/AL inputs.
7. VGA + VGA AUDIO INPUT
Connect a signal of VGA (RGBHV) to the HD-15F female connector.
Connect the output port of your source audio device to the audio input.
8. DVI + DVI AUDIO INPUT
Connect a signal of DVI to the digital video connector. Connect the
output port of your source audio device to the audio input.
9. HDMI INPUT
Connect 8 signal link of HDMI direct digital video/audio to the HDMI
connector, which supports HDMI digital video/audio and DVI digital
video sources.
Component video via 3x RCAs
Female RCA connectors
Stereo audio via 2x RCAs
Female RCA connectors
VGA video jack
Female HD-15F connector
Female DVI connector
HDMI female jack
10. DISPLAY PORT INPUT
Connect a signal of display port to the DP port, which supports digital
video and audio.
Display port digital video and audio
connector
6
REAR PANEL
REAR PANEL
11. VIDEO + AR I AL AUDIO INPUT
Connect a signal of composite video to the RCA connector.
Connect the output port of your source audio device to the
AR/AL inputs.
12. S-VIDEO + AR / AL AUDIO INPUT
Connect a signal input of S-Video to the connector. Connect the
output port of your source audio device to the AR/AL inputs.
13. SPDIF
Connect for digital audio output.
14. VGA OUTPUT
Connect a signal source of VGA(RGBHV) to the VGA connector.
Female RCA connector Stereo Audio
(AR/AL) Via 1x 03.5mm ear phone jack
connector
Note: With 1x female phone jack each
channel
Mini-DIN connector Stereo Audio (AR/
AL) Via 1x 03.5mm ear phone jack
connector
Note: With 1x female phone jack each
channel
Female RCA connector
Component Video (YPBPR) Via 3x
RCAs
Note: With 3x RCA female connectors.
15. HDMI OUTPUT
Connect a signal link of HDMI direct digital video/audio to this
Female HDMI connector, which supports HDMI digital video/audio
and DVI digital video sources.
HDMI digital video/audio connector
HDMI female connector
Note: With proper adapters, the scaler
can be used with DVI digital video
signals, and HDCP compliant.
7
REMOTE CONTROL
Before making any connections to the SB-3879. Observe the following:
Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%)
Ensure that the power switch is OFF
Ensure that all system grounds (earth) are connected to a common point.
Avoid powering equipment within a system from multiple power sources that may be separated by large distances
Connect all audio video sources and destination equipment
Power up all source and destination audio-visual sources
For each destination output select the appropriate input source by using The front panel input select buttons. The supplied IR remote
control. Or through the RS-232 serial communications port.
Upon power up the switcher will return to its last used setting before Powered down.
REMOTE CONTROL
For guidance on the OSD options, please refer to the OSD
instruction manual.
IR REMOTE CONTROL KEY :
1/2. POWER ON AND OFF: Turns on or off the scaler
3. MUTE: Stops playing sounds
4. SOURCE (HDMI, VGA, DVI, DP, YPBPR, VIDEO, S-VIDEO):
Selects your input signal type
5. ENTER: Confi rms your selection/enter the next layer of OSD options
6. ARROW KEYS: move up, down, left or right between the OSD
options. Use left and right keys to adjust the value of a parameter. Use
down key to enter the next layer of options and up key to move back.
7. RETURN: Return to the upper layer of OSD options
8. MENU: Opens up the OSD menu
9. INFO: Checks the connection status of input/output/ RS-232/Ethernet
ports
10. EXIT: Leaves the OSD menu
11. OUTPUT (XGA, WXGA, 720P, 1080P, OTHERS): Selects the
desired output resolution supported by your display device.
12. OSD TIME OUT: Adjusts the OSD menu display time
13. VIDEO WALL: Opens the video wall options
8
IR CODES
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES:
CUSTOM CODE: 20DF
POWER ON: 20DF 5DA2
POWER OFF: 20DF 5EA1
Mute: 20DF 02FD
HDMI: 20DF 1FEO
VGA: 20DF OAF5
DVI: 20DF 50AF
DP: 20DF 59A6
YPBPR: 20DF 58A7
VIDEO: 20DF 5AA5
S-VIDEO: 20DF 5BA4
RETURN: 20DF 11EE
MENU: 20DF 19EA
INFO: 20DF 1BE4
EXIT: 20DF 5CA3
ENTER: 20DF 51AE
UP: 20DF 44BB
RIGHT: 20DF 48B7
LEFT: 20DF 1CE3
DOWN: 20DF 1DE2
XGA: 20DF 07F8
WXGA: 20DF 4BB4
720p: 20DF 05FA
1080p: 20DF 06F9
OTHERS: 20DF 03FC
OSD TIME OUT: 20DF 15EA
VIDEO WALL: 20DF 15EB
Example 1: Select input VGA and output HDMI
The IR Data Code: 20DF OAF5 20DF 07F8
Example 2: Open OSD-> move right -> move down to next layer -> enter to confi rm selection
The IR Data Code: 20DF 15EA 20DF 48B7 20DF 1DE2 20DF 51AE
9
IR EXTENDER
REAR PANEL IR EXTENDER PORTS
••• When you plug the externallR extender into the scaler, the front panel IR receiver remains active . •••
IR EXTENDER PACKAGE :
HOW TO SETUP THE IR EXTENDER COMPONENTS
10
TYPICAL APPLICA TION
7 IN 2 OUT HDMI VIDEO SCALER
INSTALLING
CONTROL PORTS :
1. Front Panel - Function Key Press Buttons
2. IR Remote - IR Remote Controller
3. RS-232 Interface - RS-232 Interface System
4. Ethernet - Ethernet Interface System
INPUTS 1 ~ 7 PORT SOURCE SIGNALS : COMPONENT VIDEO, AV, DVI, HDMI, Display Port (5 input ports connected)
OUTPUTS 1 ~ 2 PORT DISPLAY SIGNALS : VGA, HDMI
SB-3879 SUPPORTS 7x INPUTS AND 2x OUTPUTS, CONTROL IR & RS-232 INTERFACE SYSTEM PORTS.
11
INPUT RESOLUTION SUPPORT
Resolution
640x350 @ 85 Hz 480p / 480i
640x400 @ 85 Hz 576p / 576i
640x480 @ 60 Hz 720p
640x480 @ 72 Hz VGA
640x480 @ 75 Hz VGA
720x400 @ 70 Hz DOS
720x400 @ 85 Hz 1080p / 1080i
800x600 @ 56 Hz SVGA
800x600 @ 60 Hz SVGA
800x600 @ 72 Hz SVGA
800x600 @ 75 Hz SVGA
832x624 @ 75 Hz SVGA
INPUT
COMPONENT VGA DVI HDMI Display Port
848x480 @ 59 Hz WVGA
848x480 @ 60 Hz WVGA
852x480 @ 60 Hz 480p
1024x768 @ 60 Hz XGA
1024x768 @ 70 Hz XGA
1024x768 @ 75 Hz XGA
1152x864 @ 75 Hz XGA+
1280x720 @ 48 Hz HD 720
1280x720 @ 50 Hz HD 720
1280x720 @ 60 Hz HD 720
1280x768 @ 60 Hz WXGA
1280x768 @ 75 Hz WXGA
1280x768 @ 60 RB WXGA
1280x800 @ 60 Hz WXGA
1280x800 @ 75 Hz WXGA
12
INPUT RESOLUTION SUPPORT
Resolution
1280x960 @ 60 Hz SXGA
1280x1024 @ 60 Hz SXGA
1280x1024 @ 75 Hz SXGA
1360x768 @ 60 Hz SXGA
1360x768 @ 75 Hz SXGA
1366x768 @ 60 Hz WXGA
1400x788 @ 60 Hz WXGA+
1400x1050 @ 60 Hz SXGA+
1400x1050 @ 75 Hz SXGA+
1400x1050 @ 60 RB SXGA+
1440x900 @ 60 Hz WXGA+
1440x900 @ 75 Hz WXGA+
INPUT
COMPONENT VGA DVI HDMI Display Port
1440x1050 @ 60 Hz SXGA+
1600x1200 @ 60 Hz UXGA
1600x1200 @ 65 Hz UXGA
1600x1200 @ 70 Hz UXGA
1600x1200 @ 75 Hz UXGA
1680x1050 @ 60 Hz WSXGA+
1792x1344 @ 60 Hz
1856x1392 @ 60 Hz
1920x1200 @ 60 RB WUXGA
1920x1200 @ 60 Hz WUXGA
1920x1440 @ 60 Hz WUXGA
1920x1440 @ 75 Hz WUXGA
720x480p @ 59 Hz DVD “NTSC”
720x480p @ 59 PW DVD “NTSC”
720x576p @ 50 Hz DVD “PAL”
13
INPUT RESOLUTION SUPPORT
Resolution
720x576p @ 50 PW DVD “PAL”
1280x720p @ 50 Hz HDTV 720p
1280x720p @ 60 Hz HDTV 720p
1280x720p @ 100 Hz HDTV 720p
1280x720p @ 120 Hz HDTV 720p
1920x1080p @ 24 Hz 1080p HD
1920x1080p @ 30 Hz 1080i HD
1920x1080p @ 50 Hz 1080p HD
1920x1080p @ 60 Hz 1080p HD
1920x1080p @ 24 Hz Full HD 1080p
2048x1280 @ 60 Hz
2560x1600 WQXGA
INPUT
COMPONENT VGA DVI HDMI Display Port
14
OUTPUT RESOLUTION SUPPORT
Front Panel Buttons Resolution
720x480
800x600
1280x800
OTHERS
1280x1024
1360x768
1400x1050
XGA 1600x1200
WXGA 1920x1200
720p 1024x768
1080p 1280x720
1080p 1920x1080
Note: When the front panel button OTHERS is pressed, the scaler will automatically apply the resolution 1360x768. Users may continue
pressing OTHERS to cycle through the following four resolutions: 1360x768 -> 1280x1024 -> 1600x1200 -> 1920x1200
OUTPUT
VGA HDMI
To select 720x480, 800x600, 1280x800, open the OSD menu and go to the IMAGE PROPERTIES to adjust the settings in the output
mode.
15
VIDEO TIMING LIST (HDMI)
H
Resolution
640x480 @ 60 Hz 31.484 59.97 25.1875 800 640 16 96 N 525 480 10 2 N
640x480 @ 72 Hz 37.861 72.809 31.5 832 640 24 40 N 520 480 9 3 N
640x480 @ 75 Hz 37.5 75 31.5 840 640 16 64 N 500 480 1 3 N
720x400 @ 70 Hz 31.458 70.063 28.3125 900 720 16 108 N 449 400 13 2 P
800x600 @ 56 Hz 35.156 56.25 36 1024 800 24 72 P 625 600 1 2 P
800x600 @ 60 Hz 37.879 60.317 40 1056 800 40 128 P 628 600 1 4 P
800x600 @ 72 Hz 48.077 72.188 50 1040 800 56 120 P 666 600 37 6 P
800x600 @ 75 Hz 46.875 75 49.5 1056 800 16 80 P 625 600 1 3 P
848x480 @ 59 Hz 29.83 59.659 31.5 1056 848 24 80 N 500 480 3 5 P
848x480 @ 60 Hz 31.02 60 33.75 1088 848 16 112 P 517 480 6 8 P
1024x768 @ 60 Hz 48.363 60.004 65 1344 1024 24 136 N 806 768 3 6 N
1024x768 @ 70 Hz 56.476 70.069 75 1328 1024 24 136 N 806 768 3 6 N
1024x768 @ 75 Hz 60.023 75.029 78.75 1312 1024 16 96 P 800 768 1 3 P
1152x864 @ 75 Hz 67.5 75 108 1600 1152 64 128 P 900 864 1 3 P
1280x720 @ 48 Hz 35.539 47.961 58 1632 1280 48 128 N 741 720 1 3 P
1280x720 @ 50 Hz 36.918 49.822 60.25 1632 1280 48 128 N 741 720 1 3 P
1280x720 @ 60 Hz 44.621 59.814 74.25 1664 1280 56 136 N 746 720 1 3 P
1280x768 @ 60 Hz 47.396 59.995 68.25 1440 1280 48 32 P 790 768 3 7 N
1280x768 @ 60 Hz 47.776 59.87 79.5 1664 1280 64 128 N 798 768 3 7 P
1280x768 @ 75 Hz 60.289 74.893 102.25 1696 1280 80 128 N 805 768 3 7 P
1280x800 @ 60 Hz 49.702 59.81 83.5 1680 1280 72 128 N 831 800 3 6 P
1280x800 @ 75 Hz 62.795 74.934 106.5 1696 1280 80 128 N 838 800 3 6 P
1280x960 @ 60 Hz 60 60 108 1800 1280 96 112 P 1000 960 1 3 P
1280x1024 @ 60 Hz 63.981 60.02 108 1688 1280 48 112 P 1066 1024 1 3 P
1280x1024 @ 75 Hz 79.976 75.025 135 1688 1280 16 144 P 1066 1024 1 3 P
1360x768 @ 60 Hz 47.712 60.015 85.5 1792 1360 64 112 P 795 768 3 6 P
1366x768 @ 60 Hz 48 60 72 1500 1366 14 56 P 800 768 1 3 P
1400x1050 @ 60 Hz 64.744 59.948 101 1560 1400 48 32 P 1080 1050 3 4 N
1400x1050 @ 60 RB 65.317 59.978 121.75 1864 1400 88 144 N 1089 1050 3 4 P
1400x1050 @ 75 Hz 82.278 74.867 156 1896 1400 104 144 N 1099 1050 3 4 P
1440x900 @ 60 Hz 55.935 59.887 106.5 1904 1440 80 152 N 934 900 3 6 P
1440x900 @ 75 Hz 70.506 74.847 136.5 1936 1440 96 152 N 942 900 3 6 P
1440x1050 @ 60 Hz 65.234 59.903 125.25 1920 1440 88 152 N 1089 1050 3 10 N
1600x1200 @ 60 Hz 75 60 162 2160 1600 64 192 P 1250 1200 1 3 P
1680x1050 @ 60 Hz 65.402 60.057 146.5 2240 1680 104 176 N 1089 1020 3 6 P
1920x1200 @ 60 RB 74.038 59.95 154 2080 1920 48 32 P 1235 1200 3 6 N
720x480p @ 59 Hz 31.469 59.94 27 858 720 16 62 N 525 480 9 6 N
720x480p @ 59 PW 31.469 59.94 27 858 720 16 62 N 525 480 9 6 N
720x576p @ 50 Hz 31.25 50 27 864 720 12 64 N 625 576 5 5 N
720x576p @ 50 PW 31.25 50 27 864 720 12 64 N 625 576 5 5 N
1280x720p @ 50 Hz 37.5 50 74.25 1980 1280 440 40 P 750 720 5 5 P
1280x720p @ 60 Hz 45 60 74.25 1650 1280 110 40 P 750 720 5 5 P
1280x720p @ 100 Hz 75 100 148.5 1980 1280 440 40 P 750 720 5 5 P
1280x720p @ 120 Hz 90 120 148.5 1650 1280 110 40 P 750 720 5 5 P
1920x108p @ 24 Hz 27 24 74.25 2750 1920 638 44 P 1125 1080 4 5 P
1920x108p @ 30 Hz 33.75 30 74.25 2200 1920 88 44 P 1125 1080 4 5 P
1920x108p @ 50 Hz 56.25 50 148.5 2640 1920 528 44 P 1125 1080 4 5 P
1920x108p @ 60 Hz 67.5 60 148.5 2200 1920 88 44 P 1125 1080 4 5 P
Freq.
(Khz)
V
Freq.
(Hz)
Pixel
Clock
(MHz)
H
Total
Pixel
H
Display
Pixel
Porch
16
H
Front
H
Sync
Width
H
Sync
Pol
V
Total
Lines
V
Display
Lines
V
Front
Porch
V
Sync
Width
V
Sync
Pol
VIDEO TIMING LIST (VGA)
H
V
Resolution
640x480 @ 60 Hz 31.563 60.119 25.1875 800 640 16 96 N 525 480 10 2 N
640x480 @ 72 Hz 37.861 72.809 31.5 832 640 24 40 N 520 480 9 3 N
640x480 @ 75 Hz 37.5 75 31.5 840 640 16 64 N 500 480 1 3 N
720x400 @ 70 Hz 31.528 70.218 28.3125 900 720 16 108 N 449 400 13 2 P
800x600 @ 56 Hz 35.156 56.25 36 1024 800 24 72 N 625 600 1 2 P
800x600 @ 60 Hz 37.879 60.317 40 1056 800 40 128 N 628 600 1 4 P
800x600 @ 72 Hz 48.077 72.188 50 1040 800 56 120 N 666 600 37 6 P
800x600 @ 75 Hz 46.875 75 49.5 1056 800 16 80 P 625 600 1 3 P
848x480 @ 59 Hz 29.83 59.659 31.5 1056 848 24 80 N 500 480 3 5 P
848x480 @ 60 Hz 31.02 60 33.75 1088 848 16 112 P 517 480 6 8 P
1024x768 @ 60 Hz 48.363 60.004 65 1344 1024 24 136 N 806 768 3 6 N
1024x768 @ 70 Hz 56.476 70.069 75 1328 1024 24 136 N 806 768 3 6 N
1024x768 @ 75 Hz 60.023 75.029 78.75 1312 1024 16 96 N 800 768 1 3 P
1152x864 @ 75 Hz 67.5 75 108 1600 1152 64 128 P 900 864 1 3 P
1280x720 @ 48 Hz 35.539 47.961 58 1632 1280 48 128 N 741 720 1 3 P
1280x768 @ 60 RB 47.396 59.995 68.25 1440 1280 48 32 P 790 768 3 7 N
1280x768 @ 60 Hz 47.776 59.87 79.5 1664 1280 64 128 N 798 768 3 7 P
1280x768 @ 75 Hz 60.289 74.893 102.25 1696 1280 80 128 N 805 768 3 7 P
1280x800 @ 60 Hz 49.702 59.81 83.5 1680 1280 72 128 N 831 800 3 6 P
1280x800 @ 75 Hz 62.795 74.934 106.5 1696 1280 80 128 N 838 800 3 6 P
1280x960 @ 60 Hz 60 60 108 1800 1280 96 112 P 1000 960 1 3 P
1280x1024 @ 60 Hz 63.981 60.02 108 1688 1280 48 112 P 1066 1024 1 3 P
1280x1024 @ 75 Hz 79.976 75.025 135 1688 1280 16 144 P 1066 1024 1 3 P
1360x768 @ 60 Hz 47.712 60.015 85.5 1792 1360 64 112 P 795 768 3 6 P
1400x1050 @ 60 RB 64.744 59.948 101 1560 1400 48 32 P 1080 1050 3 4 N
1400x1050 @ 60 Hz 65.317 59.978 121.75 1864 1400 88 144 N 1089 1050 3 4 P
1400x1050 @ 75 Hz 82.278 74.867 156 1896 1400 104 144 N 1099 1050 3 4 P
1440x900 @ 60 Hz 55.935 59.887 106.5 1904 1440 80 152 N 934 900 3 6 P
1440x1050 @ 60 Hz 65.234 59.903 125.25 1920 1440 88 152 N 1089 1050 3 10 N
1600x1200 @ 60 Hz 75 60 162 2160 1600 64 192 P 1250 1200 1 3 P
1680x1050 @ 60 Hz 65.179 59.852 146 2240 1680 104 176 N 1089 1050 3 6 P
1920x1200 @ 60 RB 74.038 59.95 154 2080 1920 48 32 P 1235 1200 3 6 N
Freq.
(Khz)
Freq.
(Hz)
Pixel
Clock
(MHz)
H
Total
Pixel
H
Display
Pixel
H
Front
Porch
H
Sync
Width
H
Sync
Pol
V
Total
Lines
V
Display
Lines
V
Front
Porch
V
Sync
Width
Sync
V
Pol
17
VIDEO TIMING LIST (DISPLAY PORT)
H
Resolution
640x480 @ 60 Hz 31.56 60.12 25.1875 800 640 16 96 N 525 480 10 2 N
640x480 @ 72 Hz 37.86 72.81 31.5 832 640 24 40 N 520 480 9 3 N
640x480 @ 75 Hz 37.5 75 31.5 840 640 16 64 N 500 480 1 3 N
720x400 @ 70 Hz 31.46 70.06 28.3125 900 720 16 108 N 449 400 13 2 P
800x600 @ 56 Hz 35.16 56.25 36 1024 800 24 72 P 625 600 1 2 P
800x600 @ 60 Hz 37.88 60.32 40 1056 800 40 128 P 628 600 1 4 P
800x600 @ 72 Hz 48.08 72.19 50 1040 800 56 120 P 666 600 37 6 P
800x600 @ 75 Hz 46.88 75 49.5 1056 800 16 80 P 625 600 1 3 P
848x480 @ 59 Hz 29.83 59.66 31.5 1056 848 24 80 P 500 480 3 5 P
848x480 @ 60 Hz 31.02 60 33.75 1088 848 16 112 P 517 480 6 8 P
1024x768 @ 60 Hz 48.36 60 65 1344 1024 24 136 N 806 768 3 6 N
1024x768 @ 70 Hz 56.48 70.07 75 1328 1024 24 136 N 806 768 3 6 N
1024x768 @ 75 Hz 60.02 75.03 78.75 1312 1024 16 96 P 800 768 1 3 P
1152x864 @ 75 Hz 67.5 75 108 1600 1152 64 128 P 900 864 1 3 P
1280x720 @ 48 Hz 35.54 47.96 58 1632 1280 48 128 N 741 720 1 3 P
1280x720 @ 50 Hz 36.92 49.82 60.25 1632 1280 48 128 N 741 720 1 3 P
1280x720 @ 60 Hz 44.62 59.81 74.25 1664 1280 56 136 N 746 720 1 3 P
1280x768 @ 60 Hz 47.4 59.99 68.25 1440 1280 48 32 P 790 768 3 7 N
1280x768 @ 60 Hz 47.78 59.87 79.5 1664 1280 64 128 N 798 768 3 7 P
1280x768 @ 75 Hz 60.29 74.89 102.25 1696 1280 80 128 N 805 768 3 7 P
1280x800 @ 60 Hz 49.7 59.81 83.5 1680 1280 72 128 N 831 800 3 6 P
1280x960 @ 60 Hz 60 60 108 1800 1280 96 112 P 1000 960 1 3 P
1280x1024 @ 60 Hz 63.98 60.02 108 1688 1280 48 112 P 1066 1024 1 3 P
1280x1024 @ 75 Hz 79.98 75.02 135 1688 1280 16 144 P 1066 1024 1 3 P
1360x768 @ 60 Hz 47.71 60.02 85.5 1792 1360 64 112 P 795 768 3 6 P
1366x768 @ 60 Hz 48 60 72 1500 1366 14 56 P 800 768 1 3 P
1400x1050 @ 60 Hz 64.74 59.95 101 1560 1400 48 32 P 1080 1050 3 4 N
1400x1050 @ 60 Hz 65.32 59.98 121.75 1864 1400 88 144 N 1089 1050 3 4 P
1400x1050 @ 75 Hz 82.28 74.87 156 1896 1400 104 144 N 1099 1050 3 4 P
1440x900 @ 60 Hz 55.93 59.89 106.5 1904 1440 80 152 N 934 900 3 6 P
1440x900 @ 75 Hz 70.51 74.85 136.5 1936 1440 96 152 N 942 900 3 6 P
1440x1050 @ 60 Hz 65.23 59.9 125.25 1920 1440 88 152 N 1089 1050 3 10 N
1600x1200 @ 60 Hz 75 60 162 2160 1600 64 192 P 1250 1200 1 3 P
1600x1200 @ 65 Hz 81.25 65 175.5 2160 1600 64 192 P 1250 1200 1 3 P
1600x1200 @ 70 Hz 87.5 70 189 2160 1600 64 192 P 1250 1200 1 3 P
1600x1200 @ 75 Hz 93.52 74.81 202 2160 1600 64 192 P 1250 1200 1 3 P
1680x1050 @ 60 Hz 65.18 59.85 146 2240 1680 104 176 N 1089 1050 3 6 P
1920x1200 @ 60 RB 74.04 59.95 154 2080 1920 48 32 P 1235 1200 3 6 N
1920x1200 @ 60 Hz 74.46 59.81 193 2592 1920 136 200 N 1245 1200 3 6 P
2560x1600 @ 60 Hz 98.53 59.86 268 2720 2560 48 32 P 1646 1600 3 6 N
720x480p @ 59 Hz 31.47 59.94 27 858 720 16 62 N 525 480 9 6 N
720x480p @ 59 PW 31.47 59.94 27 858 720 16 62 N 525 480 9 6 N
720x576p @ 50 Hz 31.25 50 27 864 720 12 64 N 625 576 5 5 N
720x576p @ 50 PW 31.25 50 27 864 720 12 64 N 625 576 5 5 N
1280x720p @ 50 Hz 37.5 50 74.25 1980 1280 440 40 P 750 720 5 5 P
1280x720p @ 60 Hz 45 60 74.25 1650 1280 110 40 P 750 720 5 5 P
1280x720p @ 100 Hz 75 100 148.5 1980 1280 440 40 P 750 720 5 5 P
1280x720p @ 120 Hz 90 120 148.5 1650 1280 110 40 P 750 720 5 5 P
Freq.
(Khz)
V
Freq.
(Hz)
Pixel
Clock
(MHz)
H
Total
Pixel
H
Display
Pixel
Porch
18
H
Front
H
Sync
Width
H
Sync
Pol
V
Total
Lines
V
Display
Lines
V
Front
Porch
V
Sync
Width
V
Sync
Pol
VIDEO TIMING LIST (DISPLAY PORT)
1920x1080i @ 50 Hz 28.13 25 74.25 2640 1920 528 44 P 1125 1080 2 5 P
1920x108p @ 24 Hz 27 24 74.25 2750 1920 638 44 P 1125 1080 4 5 P
1920x108p @ 30 Hz 33.75 30 74.25 2200 1920 88 44 P 1125 1080 4 5 P
1920x108p @ 50 Hz 56.25 50 148.5 2640 1920 528 44 P 1125 1080 4 5 P
1920x108p @ 60 Hz 67.5 60 148.5 2200 1920 88 44 P 1125 1080 4 5 N
19
OSD OPTIONS OVERVIEW
Layer 1 Layer2 Layer3
Brightness
Contrast
Picture
Image Setup
Video Wall
3D Properties
Hue
Saturation
Sharpness
Automatic
Manual Clock / Phase / Clock
Horizontal Position
Vertical Position
Color Preset Mode / Custom
Input Signal DVI / HDMI / VGA / Display Port / Component / Composite / S-Video
Scaling Original AR/ Full Screen
Output Mode
Zoom Horizontal Zoom / Vertical Zoom
Pan Horizontal Pan / Vertical Pan
Overlap Left / Right / Top / Bottom (Edges) / Reset
Input Format Automatic / Side-By-Side / Top-Bottom
Output Format Left Eye Frame / Right Eye Frame
720x480, 800x600, 1280x800, 1280x1024, 1360x768, 1400x1050,
1600x1200, 1024x768, 1280x768, 1280x720, 1920x1080
Options
1080p 24Hz Output Enable / Disable
Information
Language English
Reset Reset AII / Reset Video Wall
Accessibility Button Repeat Rate (off, default, slow) / Menu Time Out / Logo Time Out
Setting
Mute
BOXID
Profi le
Network (serial port, Ethernet)
20
PICTURE
PICTURE allows you to digitally adjust the brightness, contrast, hue, saturation, and sharpness of the images. An unilluminated icon
suggests the function is not available. To enable it, the unit color must be set in custom mode. Go to the 3rd icon in the fi rst layer to change
the setting in color: Image properties -> color -> custom -> save. Be sure to save your setting. Otherwise, the value will not be set.
• Layer one, the 1st icon from left
• Choose the icon and use the down arrow key to open the
next layer, which has fi ve options: brightness, contrast, hue,
saturation, and sharpness
• Hue, saturation, and sharpness, the three icons are illuminated
only when signals of AV, S-Video, or component video are
present on the scaler
Brightness
Use arrow key right and left to adjust the value
Contrast
Use arrow key right and left to adjust the value
Hue
Use arrow key right and left to adjust the value
Adjustable only when the unit receives valid AV, S-Video, or component video signals.
Saturation
Use arrow key right and left to adjust the value
Adjustable only when the unit receives valid AV, S-Video, or component video signals.
Sharpness
Use arrow key right and left to adjust the value
Adjustable only when the unit receives valid AV, S-Video, or component video signals.
21
IMAGE SETUP
To enable the IMAGE SETUP, a valid VGA signal must be present on the scaler . An illuminated icon indicates the presence of a VGA signal.
• First layer, the 2nd icon from left
• Choose the icon and use the down arrow key to open the
second layer, which has four options: automatic, manual,
horizontal position, vertical position
Automatic
SB-3879 reads the Input signal and automatically sets the optimal value for the Output.
Manual
Clock / Phase / Save
Horizontal Position
Move the image to right or left.
Vertical Position
Move the image up or down.
22
IMAGE PROPERTIES
IMAGE PROPERTIES allow you to change Color, select Input Signal, adjust scaling, and change Output Resolution. Resolutions not
listed on the front panel button can be selected here, under the output mode.
• Layer one, the 3rd icon from left
• Choose the icon and use the down arrow key to open up
the second layer, which has four options: color, input signal,
scaling, output mode
• Setting the color in custom mode can enable the PICTURE
function (layer one, the 1st icon from left).
Color
Preset Mode: Standard, RGB, warm, cold
Custom: Red, Green, Blue, Save
Input Signal
DVI, HDMI, VGA, Display Port, Component, Composite Video, S-Video
Scaling
Original AR, Full Screen
Output Mode
Select one desired output resolution from the following 11 choices.
OTHERS 720x480, 800x600, 1280x800, 1280x1024, 1360x768, 1400x1050, 1600x1200, 1920x1200
XGA 1024x768
WXGA 1280x768
720p 1280x720
1080p 1920x1080
When the front panel button OTHERS is pressed, the scaler will automatically apply the resolution 1360x768.
Users may continue pressing OTHERS to cycle through the following four resolutions:
1360x768 -> 1280x1024 -> 1600x1200 -> 1920x1200
23
TV WALL
SB-3879 scaler is able to send divided images on multiple display devices and build a video wall, be it a wall of size 1x2, 2x2, or 10x10.
Maximally, the scaler can make possible a video wall of 15 by 15 screens. Note that an SB-3879 is required for each output. Users may
arrange the position and adjust the size of each image block under the TV WALL function.
• Layer one, the 3rd icon from the left
• Choose the TV wall icon, use the down arrow key to open the
next layer, which has three options: zoom, pan, overlap
ZOOM: Use right / left key to adjust the value of the parameter:
Horizontal zoom: enlarge the image on the left and right ends.
Vertical zoom: enlarge the image upwardly and downwardly.
PAN: Arrange the relative position of the image in the TV wall. First calculate the size of the TV wall: the number of displays horizontally
and vertically connected. Then, assign numbers to indicate relative position. Take the following two TV walls for example.
3x2 TV wall (Horizontal: 3 ; Vertical: 2)
Display No.4 should be assigned:
Horizontal Zoom = 1
Vertical Zoom = 2
Display No.5 should be assigned:
Horizontal Zoom = 2
Vertical Zoom = 2
OVERLAP: Align the overlapping images for visual continuum. Move the image up, down or to left, right by adjusting the parameters of
the top edge, bottom edge, left edge, and right edge. To return to the original setting, press RESET.
3x3 TV wall (Horizontal: 3 ; Vertical: 3)
Display No.9 should be assigned:
Horizontal Zoom = 3
Vertical Zoom = 3
24
OPTIONS
OPTIONS allows you to check the connection status, change menu language, return to factory default, save setting, and make adjustments
to the setting of the OSD menu .
• Layer one, the 6th icon from left
• Press the down arrow key to open up the second layer, which
has fi ve options: info, language, reset, accessibility, setting
INFO: Check the connection status of Input/Output ports, the model name, the connection status of RS-232/Ethernet ports, and fi rmware version.
LANGUAGE: Arrange the relative position of the image in the TV wall. First calculate the size of the TV wall: the number of displays
horizontally and vertically connected. Then, assign numbers to indicate relative position. Take the following two TV walls for example.
RESET: Return to factory default setting.
Reset all: reset all options.
Reset video wall: reset all the options relating to video wall function only.
Accessibility:
Button repeat rate: Adjust the unit response time when MENU button is pressed.
Off: Press MENU button, and the MENU shows up/disappears once.
Default: Return to the factory default setting.
Slow: Press MENU button and hold on for longer seconds, the unit will take more time than default to respond.
Menu time out: Adjust the length of time OSD menu stays on screen.
On: The OSD menu will disappear after a period of time. You can lengthen or shorten the menu display time.
Off: Stop the OSD menu from disappearing automatically. When the function is turned off, the OSD menu will not disappear until
MENU button is pressed again.
Logo time out: Adjust the length of time the logo stays on screen when the unit is turned on.
SETTING:
Mute: Stop playing sounds.
BOX 10: Check the 10 of the unit.
Profi le: Save and reload the settings. The unit can memorize a total of 5 different settings.
Network: Serial Port, Ethernet
25
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTW ARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its affi liates, including any manufacturers or distributors of the Product (collectively , “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its offi ces within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENT A TIONS REGARDING THE USE OR THE RESUL TS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT W ARRANT THA T THE FUNCTIONS PERT AINING TO THE PRODUCT WILL BE ERROR-FREE, THA T DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERT AINING THERET O ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THA T RESUL T FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
26
MULTIMEDIA AUDIO AND VISUAL
1399 Wildfi re Lane | Frisco, TX 75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com
www.shinybowusa.com
Loading...