User Manual
ANI-3088
Matrix Switching System
ANI-3088
MATRIC
SWITCHING SYSTEMS
ANI-3088 Matrix Switching System - User Manual
1
Before You Use the System
1. Read manual——Carefully read the manual before you use the system.
2. Installation environment——The system should be installed indoor only. Install either in a
sturdy rack or desk in a well-ventilated place.
3. Lightning——Unplug the power cord during lightning or after a prolonged period of non-use
to avoid damage to the equipment.
4. Maintenance——Only qualified technical engineers are permitted to
components and parts of the equipment upon failure.
repair or replace
ANI-3088 Matrix Switching System - User Manual
2
Table of Contents
1.0 Matrix System Overview ..........................................................................................................3
1.0.1 ANI-3088 Matrix System.................................................................................................3
1.0.2 Matrix System Packing..................................................................................3 ANI-3088
2.0 Matrix Host Installation............................................................................................4 ANI-3088
3.0 Matrix System Models..............................................................................................ANI-3088 5
4.0 Matrix System Front/Rear Panels .............................................................................................5
5.0 Matrix and Peripherals Connection..........................................................................6 ANI-3088
5.0.1 Input/Output Jacks..................................................................................................................6
5.0.1.1 Audio/Video Connecting Cable........................................................................... 7
5.0.2 Matrix and Control Computer Connection....................................................8 ANI-3088
5.0.3 Remote Control Methods and Settings........................................................................... 9
5.0.3.1 RS-232 Communication Port, Connection Methods...........................................9
5.0.3.2 RS-485 Communication Port ............................................................................ 11
5.0.3.3 On/Off Switch Settings .....................................................................................11
5.0.3.4 Matrix System and Control System Connection...............................13 ANI-3088
6.0 Matrix Control Panel Operation..............................................................................................15
6.0.1 Input/Output Switching Key Operation Mode ............................................................. 15
6.0.2 Front Panel Key Functions........................................................................................... 15
6.0.3 Operation Examples .....................................................................................................16
7.0 Matrix Application Software....................................................................................................19
7.0.1 Software Introduction....................................................................................................19
7.0.1.1 Software Description.........................................................................................19
7.0.1.2 Software Activation...........................................................................................19
7.0.2 Software Features.........................................................................................................19
7.0.2.1 Main Operation Interface Functions .................................................................20
7.0.2.2 Disconnect Function Keys ................................................................................22
7.0.2.3 Select all output, DeSelect all output Switching Functions .............................. 23
7.0.2.4 Disconnect all Command .................................................................................. 23
7.0.2.5 Memory Function Usage................................................................................... 23
7.0.2.6 Scan Function Usage.........................................................................................24
7.0.2.7 Options Function Usage .................................................................................... 24
7.0.2.8 Exit Function Usage .......................................................................................... 25
7.0.2.9 Other Usages ..................................................................................................... 25
8.0 Communication Protocol and Control Command Code .........................................................25
9.0 ANI-3088 Matrix System Technical Parameters......................................................................26
10.0 Common Problems and Solutions..........................................................................,............... 27
ANI-3088 Matrix Switching System - User Manual
1.0 Matrix System Overview
3
1.0.1 Matrix System ANI-3088
Figure 1-1 ANI-3088 Matrix
1.0.2 ANI-3088 Matrix System Packing
A N I - 3 0 8 8 M atrix H ost
RS-232 Communication Connecting Cable
The ANI-3088
ANI-3088
ANI-3088
Matrix switcher is a high performance switching equipment for audio/video
frequencies.
It is used for multiple input/output cross switching of audio/video signals. It provides
independent YPbPr component and audio input/output terminals. Each YPbPr component
signal and audio signal is transmitted separately and switched separately, thereby minimizing
signal attenuation and ensuring high definition graphics and high fidelity signal output.
The Series Matrix is used mainly in TV broadcasting projects, multi-media
conference halls, large display projects, TV teaching and command control centers. It boasts
features of power interruption protection during power surge, LCD display and synchronous
and separate audio/video switching functions. Its RS-232 and RS-485 communication ports
enable convenient communication with remote control equipment. This manual describes
using of the model.
ANI-3088
MATRIC SWITCHING
SYSTEMS
ANI-3088 Matrix Switching System - User Manual
4
Power Cord
A N I - 3 0 8 8 M atrix T esting and A pplications Software C D
User Manual
2.0 ANI-3088 Matrix Host Installation
The ANI-3088 Series Matrix Host has a black metallic housing. It can be placed on a sturdy
desk k. See Figure 2-1 below: or installed on a 19-in rac
Figure 2-1 Installing the ANI-3088 Matrix Host on a Standard Rack
Green Terminal(M) Quantity
ANI-3088
ANI-3088 Matrix Switching System - User Manual
5
3.0 ANI-3088 Matrix System Model
Technical
Parameters
Model
Video
Input
Port
Video
Output
Port
Audio
Input
Port
Audio
Output
Port
RS-485
Connector
RS-232
ANI-3088 8 8 8 8 √ √
4.0 Matrix System Front/Rear Panels
Figure 4-1 ANI-3088 Front Panel
Figure 4-2 ANI-3088 Rear Panel
Connector
ANI-3088 Matrix Switching System - User Manual
6
5.0 ANI-3088 Matrix and Peripherals Connection
Figure 5-1 ANI-3088 Matrix System Connection
5.0.1 Input/Output Jacks
Referring to the different matrix models, the video signal input/output jacks are formed by
the 4th and 8th rows RCA female connectors. The connectors from top to bottom are: Y, Pb/Cb,
Pr/Cr, Audio Signal Jack. The Y signal jack is green, the Pb/Cb signal jacks are blue, the Pr/Cr
signal jacks are red, and the upper row audio jacks are red (right audio channel) and the lower
row audio jacks are white (left audio channel). The output jack channels are numbered from left
to right as NO.1 to NO.8 (in five rows).
ANI-3088 Matrix Switching System - User Manual
7
Figure 6-2 YPbPr-RCA Connecting Cables
5.0.1.1 Audio/Video Connecting Cable
Different models of the YX matrix system provides a different number of input/output jacks
for users to connect to different audio/visual equipment including CD/DVD players, graphics
workstations, and number displays. The output terminals can be connected to projectors, video
recorders, displays and multiplexers and so on. The YX matrix supports various AV video signal
sources.
The RCA connecting terminal----audio/video port: The 4-hole RCA Jack is a conventional
audio connector. Its installation hole measures 14x18mm.
YPbPr Connector—Standard Video Input (3-RCA) Connector:
Type: Video connectors are in pairs (Y, Pb, Pr) (Green Y, Blue Pb, Red Pr)
For YX matrix YPbPr RCA jack connection, see Figure 6-2 below:
RCA, an abbreviation for Phono socket, is a DVD component (YpbPr) socket. The YpbPr
connector is a high definition digital TV connector (color contour YpbPr) capable of connecting
with high definition digital set-top box, satellite receiver and various high definition monitors and
TV equipment.
Color difference output (YPbPr) connector separates the modulated Y, PB and PR signals. It
separates the colorimetry C signal into blue b-Y color difference and red r-Y color difference and
uses 3 cables for separate transmission to improve display resolution. This way, it ensures the
largest bandwidth of colorimetry and averts interference to the signals because the signals are
transmitted by 3 separate cables and each cable is being properly sleeved.
The Audio Connecting Cable:
Type: The audio connecting cables are in pair for left and right channels (R for red and L for left).
Connection of the RCA connector of the ANI-3088 matrix audio is as shown in Figure 6-3 below:
Figure 6-3 AUDIO RCA Connecting Cables
ANI-3088 Matrix Switching System - User Manual
8
5.0.2 YX Matrix and Control Computer Connection
Use the RS-232 connecting cable to connect a computer serial port (COM1 or COM2) to
the RS-232 communication port of the matrix host.ANI-3088
The computer can then be used to
control the ANI-3088 matrix after installation of application software.
Figure 5-4 ANI-3088 Matrix and Computer Connection
The RCA connector uses coaxial signal transmission with the axial for signal transmission and
the outer ring for grounding. It can be used to transmit digital audio signals and modulated video
signals. Generally, the RCA audio connectors are in pairs separately indicated by red for the
right audio channel (R for right) and black or white for the left audio channel (L for left). The
RCA stereo cable is in one set for both left and right audio channels with each channel in one
cable.
Connection Method: Use the RCA (often referred to as the phono socket) connector for
connection. You are recommended to use the 14 x 18mm 4-hole RCA JAYK connector for
connection to input and output equipment. Connect the RCA video and audio connectors of the
signal source equipment output terminal to the same channel RCA connector of the
matrix input terminal, and also connect the RCA connectors of the matrix output
terminal to the RCA input connectors of the output equipment via a dedicated RCA signal cable.
NOTE: The RCA connectors at both ends of the various signal cables must correspond to each other,
otherwise loss of color reproduction or even no signal output could happen.
ANI-3088
ANI-3088
ANI-3088 Matrix Switching System - User Manual—
9
Pin NO. Leg Description
1 N/u Null
2 Tx Send
3 Rx Receive
4 N/u Null
5 Gnd Ground
6 N/u Null
7 N/u Null
8 N/u Null
9 N/u Null
Fgiure 5-5
5.0.3 Remote Control Methods and Settings
The ANI-3088 matrix provides standard RS-232 and RS-485 serial communication ports. Aside
from using the front panel keys for switching operation, you are also permitted to use the RS-232
and RS-485 serial communication ports for remote operation. It also supports RS-485 serial
control.
5.0.3.1 RS-232 Communication Port, Connection Methods
The RS-232 port is a 9-pin female connector. The Leg functions are shown in the table below:
ANI-3088 Matrix Switching System - User Manual
10
Figure 5-5 （a）
Figure 5-6
Note: The Matrix RS-232 port is defined as DCE.
ANI-3088 Matrix Switching System - User Manual
11
5.0.3.2 RS-485 Communication Port
You can use the RS-485 port to control more than one ANI-3088 product.
The RS-485 Port as shown in Figure 5-7 below:
Figure 5-7
5.0.3.3 On/Off Switch Settings
Figure 5-8
A. DIP SW-8:RS-232/RS-485 switches ON/OFF
ON:RS-232 Enables Sing
le System or RS-485 Serial Master
OFF:RS-485 Enables RS-485 Serial Slave
B. DIP sw-6/7:RS-485 Terminator ON/OFF
ON:Terminator ON
OFF:Terminator O FF
C. DIP sw 1 to 5 Setting（address setting）
The ID address determines the position of a ANI-3088 Matrix system. When multiple products
are connected to one PC or when the Matrix products are serially connected, the ID address
decides which product is to be controlled. Use the on/off switches 1, 2, 3, 4, 5 on the rear
panel to set the ID address as shown in Figure 5-2 below:
RS-485 TERMINATOR
RS-485
ANI-3088 Matrix Switching System - User Manual
12
ON/OFF Switch Settings ID Address
（Decimal）
Software ID
Address
（Hexadecimal）
ON/OFF
（Binary）
SW1 SW2 SW3 SW4 SW5
0 00 00000 OFF OFF OFF OFF OFF
1 01 00001 OFF OFF OFF OFF ON
3 03 00011 OFF OFF OFF ON ON
4 04 00100 OFF OFF ON OFF OFF
5 05 00101 OFF OFF ON OFF ON
6 06 00110 OFF OFF ON ON OFF
7 07 00111 OFF OFF ON ON ON
8 08 01000 OFF ON OFF OFF OFF
9 09 01001 OFF ON OFF OFF ON
10 0A 01010 OFF ON OFF ON OFF
11 0B 01011 OFF ON OFF ON ON
12 0C 01100 OFF ON ON OFF OFF
13 0D 01101 OFF ON ON OFF ON
14 0E 01110 OFF ON ON ON OFF
15 0F 01111 OFF ON ON ON ON
16 10 10000 ON OFF OFF OFF OFF
17 11 10001 ON OFF OFF OFF ON
18 12 10010 ON OFF OFF ON OFF
19 13 10011 ON OFF OFF ON ON
20 14 10100 ON OFF ON OFF OFF
21 15 10101 ON OFF ON OFF ON
23 17 10111 ON OFF ON ON ON
24 18 11000 ON ON OFF OFF OFF
25 19 11001 ON ON OFF OFF ON
26 1A 11010 ON ON OFF ON OFF
27 1B 11011 ON ON OFF ON ON
29 1D 11101 ON ON ON OFF ON
30 1E 11110 ON ON ON ON OFF
31 1F 11111 ON ON ON ON ON
Figure 5-2 ID Address Settings
2 02 00010 OFF OFF OFF ON OFF
22 16 10110 ON OFF ON ON OFF
28 1C 11100 ON ON ON OFF OFF
ANI-3088 Matrix Switching System - User Manual
13
5.0.3.4 ANI-3088 Matrix System and Control System Connection
A. If PC provides RS-232，connection is as in Figure 5-9 below:
Figure 5-9
NOTE: 1. For RS-232 connection refer to previous Figure for operation；
2. RS-232 or RS-485 baud rates: 9600bps, no odd or even calibration address, 8bit data
transmission address, 1bit stop address（96，N，8，1）；
3. Serial connection between Matrix RS-485 as follows:
TX（+） TX（+）
TX（-） TX（-）
RX（+） RX（+）
RX（-） RX（-）
4. Each DIP sw1-5 address must not set to same ID address.
RS-485 TERMINATOR
RS-485
RS-485 TERMINATOR
RS-485
RS-485 TERMINATOR
RS-485
RS-485 TERMINATOR
RS-485
ANI-3088 Matrix Switching System - User Manual
14
B. If PC provides RS-485, connection is as in Figure 5-10 below:
Figure 5-10
NOTE: 1. RS-485 baud rate: 9600bps, no odd or even calibration address，8bit data transmission
address，1bit stop address（96，N，8，1）；
2. Connect your PC RS-485 port to the Matrix RS-485 port as follows:
TX（+） TX（+）
TX（-） TX（-）
RX（+） RX（+）
RX（-） RX（-）
3. Serial connection between Matrix RS-485 ports as shown below:
TX（+） TX（+）
TX（-） TX（-）
RX（+） RX（+）
RX（-） RX（-）
4. Each DIP sw1-5 address must not set to same ID number.
RS-485 TERMINATOR
RS-485
RS-485 TERMINATOR
RS-485
RS-485 TERMINATOR
RS-485
RS-485 TERMINATOR
RS-485
ANI-3088 Matrix Switching System - User Manual
15
6.0 Matrix Control Panel Operation
6.0.1 Input/Output Switching Key Operation Mode
You can use the front panel keys of the ANI-3088 Matrix system for fast audio/video switching.
(For details in key pressing, refer to the “Front Panel Key Pressing Instructions”.)
Operation methods as follows:
“Switching Methods” + “Output Channel＂+“Input Channel＂
Description:
“Switching Methods”
Synchronous audio/video switching or separate switching: Using the “Audio” and “Video” keys
on the front panel, you can select “Synchronous Audio/Video Switching,” “Audio Switching
Only” or “Video Switching Only.”
“Output Channel＂
The “OUT Row 1-8” keys on the front panel represent output channels 1 to 8 for connection to
peripheral display.
“Input Channel＂
The “IN Row 1-8” keys on the front panel represent input channels 1 to 8 for connection to the
currently connected channels of the signal source to be switched.
6.0.2 Front Panel Key Functions
Part Function Key Function
1
LCD display shows current ANI-3088 matrix status and
operation hints.
2 Output channel selection keys used for setting
audio/video output channels or for selection of Status
Retrieve or Stored Number.
3 Input channel selection keys used for setting audio/video
input channels or for selection of Status Retrieve or
Stored Number.
4
ALL
Implement all output selection keys via certain input
route.
---Example: First press the “ALL” key, then select the
input channel to output to all output channels; first press
the “ALL”key, then press the “OFF” key to close all the
presently displayed swtitching status.
ANI-3088 Matrix Switching System - User Manual
16
Part Function Key Function
5
OFF
Close output channel key.
---First press to close the output channels, then press the
“OFF” key to close the specified channel.
6
STO
The “Store Key” saves all current input/output
corresponding relations.
---Example: Press the “STO”key, then press the output
channel key which you want to save all currently
displayed input/output corresponding relations.
7
RCL
The “Retrieve Key” retrieves the saved input/output
corresponding relations.
---Example: First press the “RCL” key, then press the
previously saved output channel key to retrieve the saved
input/output status and implement this status switching.
8
AUDIO
The audio switching selection key switches to another
output channel from the same channel.
Example: Press the Audio key to open or close the Audio
switching function. When the LED indicator next to the
Audio key lights shows switching function is open and
when the light goes off shows you have selected to close
the audio switching function.
9
VIDEO
The video switching selection key switches to another
output channel from the same channel.
Example 1: Press the Video key to open or close the
video switching function. When the LED indicator next
to the Video key shows video switching function is open
and when the light goes off shows the switching function
is close.
6.0.3 Operation Examples
Examle 1: Synchronously switch the NO. 1 audio/video signals to the NO. 3 and 4 output
channels.
Key LCD Display Operation
1. Press the NO. 3 key of the
output channel for 2 seconds, then
enter the input channel when the
red 0 on LCD begins to flicker.
ANI-3088 Matrix Switching System - User Manual
17
Key LCD Display Operation
2.Press the NO.1 key of the Input
channel for 2 seconds for selection
of NO.1 channel to input into
NO.3 channel for output. The
LCD shows 1 at channel NO.3
for both Audio and Video. Enter
the Output channels.
3. Press the NO.4 key of the
output channel for 2 seconds and
then enter the input channel when
the red 0 on LCD flickers.
4. Press the NO.1 key of the input
channel for 2 seconds for selection
of NO.1 channel for input and
NO. 3 and 4 channels for output.
LCD shows 1 at NO.3 and NO.4
channels for both Audio and
Video.
Example 2: Operation for synchronously switching video signals from NO.4 channel to NO.1, 3,
5 and 6 output channels.
Key LCD Display Operation
1. Press the AUDIO key to
turn off the LED indicator,
then enter the output channel.
2. Press the NO.1 key of the output
channel for 2 seconds, then enter the
input channel when the red 0 on
LCD flickers.
3. Press the NO.4 key of the input
channel for 2 seconds to select
operation of input from NO.4
channel and output from NO.1
channel. Enter the output channel
when VIDEO shows 4 at NO.1
channel on LCD.
ANI-3088 Matrix Switching System - User Manual
18
Key LCD Display Operation
4.Press the NO.3 key of the output
channel for 2 seconds and enter the
input channel when the red 0 on
LCD flickers.
5.Press the NO.4 key of the input
channel for 2 seconds to select
operation of input from NO.4
channel and output from NO.1 and
NO.3 channels. Enter the output
channel when VIDEO shows “4” at
NO.1 and NO.3 channels on LCD.
6.Press the NO.5 key of the output
channel for 2 seconds and enter the
input channel when the red 0 on
LCD flickers.
7.Press the NO.4 key of the input
channel for 2 seconds to select
operation of input from NO.4
channel and output from NO.1, 3 and
5 channels. Enter the output channel
when VIDEO shows “4” at NO.1, 3
and 5 channels on LCD.
8. Press the NO.6 key of the output
channel for 2 seconds and enter the
input channel when the red 0 on
LCD flickers.
9. Press the NO.4 key of the input
channel for 2 seconds to select the
operation of input from NO.4
channel and output from NO.1, 3, 5
and 6 channels. VIDEO shows “4” at
NO.1,3, 5 and 6 channels on LCD.
ANI-3088 Matrix Switching System - User Manual
19
7.0 Matrix Application Software
7.0.1 Software Introduction
The 《AV Matrix》 Matrix control software applies to different input/output matrixes.
7.0.1.1 Software Description
The《AV Matrix》 matrix testing software is an application tool developed for matrix testing
and application. The software operation environment is as follows:
Window98/2000/NT/XP operatng systems
32M interal memory or above
10M hard disk space or above
CD-ROM
At least one serial communicatin port
7.0.1.2 Software Activation
First, you must turn off power both to the maANI-3088
trix and to the computer. Then, connect the
matrix RS-232 port to the PC RS-232 port using the bundled communication cable. (Refer to the
previous section “ Matrix and Control Computer Connection.”; ANI-3088
Turn on power to the matrix and the computer: ANI-3088
Activate the AV Matrix.exe on the bundled CD-ROM in the control computer to enter the
control software interface.
7.0.2 Software Features
The software controls signal connection between the corresponding input port and output port
as required. The main operation window is shown in Figure 7-1 below:
Figure 7-1 《AV Matrix》 Control Software Usage Interface
ANI-3088
ANI-3088 Matrix Switching System - User Manual
20
Scroll on the left lower corner to view contents as shown below.
7.0.2.1 Main Operation Interface Functions
Refer to the window menu above, the interface blue area shows crossing matrix of output
ports 01-08 and input ports 01-08. On the lower right hand corner, you can select either
“Video” for signal input switching or “Disconnect”to close all output ports. Click to check the
white box to the left of “Video” or “Audio” for video or audio signal transimission.
Examples for Selecting Matrix Switching Functions:
Example 1: Now there is a matrix having ANI-3088 all the input/output ports properly
connected to the equipment. There are two ways of operation if you want to set channel 1
audio/video to channels 2, 3 and 5 for output and channel 3 audio/video to channel 6 for output:
First way: Make sure you have selected“Video” and “Audio” by checking the white boxes
to the left. Directly click on the corresponding icons on the matrix to turn them into
to complete the switching operation.
Second way:
Step 1: Make sure you have selected “Video” and “Audio” by checking the boxes to the left.
Step 2: First select the “Output”number keys 02, 03 and 05 to the right, and select the
“Input” number key 01 to the bottom. Afterwards, press consecutively the previously selected
“Output” number keys 02, 03 and 05 (or you can press the “Deselect all output” key). This way,
you have selected “Input” 01 and “Output” 02, 03 and 05 switching.
Step 3: First select the “Output” number key 06 to the right, and select the “Input” number
key 03 to the bottom. Afterwards, press the previously selected “Output” number key 06 (or you
can press the “Deselect all output” key). This way, you have selected Input 03 and Output 06
switching.
Upon completion of the above 3 steps, you have actually completed the switching operation of
having Audio/Video channel 1 to Output channels 2, 3 and 5 while at the same time successfully
switched from Audio/Video channel 3 to Output channel 6.
Example 2: Now, there is a matrix with the ANI-3088 input/output ports properly connected to
the equipment. It is required to set the input/output connectors to switching from video channel 1
to output channels NO.1, 6 and 7 and also to switch from audio channel 2 to output channel 8.
There are two ways of operations:
ANI-3088 Matrix Switching System - User Manual
21
First Way:
Step 1: Make sure you have selected “Video” and not “AUDIO”. Directly click on the icons
on the matrix corresponding to the INPUT number key 01 and the OUTPUT number keys
01、06、07 to turn into ，you have then selected video switching of input 01 and
output 01,06,07.
Step 2: Make sure you have selected “AUDIO” and not “Video”. Directly click on the matrix
icons corresponding to INPUT number key 02 and OUTPUT number key 08 to turn
them into ，you have then selected audio switching of input 02 and output 08.
Upon completion of the above 2 steps, you have successfully switched video channel 1 to
output channels 1, 6 and 7 and also switched audio channel 2 to output channel 8.
Second Way:
Step 1: Make sure you have selected “Video” and not “AUDIO”.
Step 2: Select the output number keys 01,06 and 07 to the right and input number key 01to the
bottom. Afterwards, press consecutively the previously pressed output number keys 01,06 and 07
to the right (or you can press the Deselect all output key). This way, you have selected video
switching of input 01 to output 01,06 and 07.
Step 3: Make sure you have selected “AUDIO”and not “Video”.
Step 4: Select output number key 08 to the right and input number key 02 to the bottom.
Afterwards, press again the previously-pressed output number key to the right（or you can
press the Deselect all output key）. This way, you have selected audio switching of input 02
and output 08.
Upon completion of the above 4 steps, you have completed the operation of switching video
channel 1 to output channels 1, 6, and 7 while also switching audio channel 2 to output channel
8.
ANI-3088 Matrix Switching System - User Manual
22
7.0.2.2 Disconnect Function Keys
Close all the unused output ports.
A specific example of operation is described below:
The present input and output relations are shown in Figure 7-2 below:
Figure 7-2
Now, you have to close the output ports 03, 05, and 06.
Step 1: First press down the output number keys 03, 05 and 06 to the right;
Step 2: Press the “Disconnect” key;
Step 3: Press the previously-pressed output number keys 03, 05 and 06 (or press the
“Deselect all output” key) to complete the operation.
The final results will be as shown in Figure 7-3 below:
ANI-3088
ANI-3088 Matrix Switching System - User Manual
23
Figure 7-3
7.0.2.3 Select all output, DeSelect all output Switching Functions
（1）Select all output Function Description: You can use this function to select one port for input
and all output ports for output.
A specific example of operation is described below:
Example: Now, you have a matrix withANI-3088 all input and output ports properly
connected to the equipment. The needed input/output ports should be set to audio/video channel
1 while switching all output ports to output.
Make sure you have selected both “Video” and “Audio” by checking the boxes to the left.
Then, press the Select all output key and select the input number key 01. Click on the
matrix icons along the 01 row to turn them into to complete the command
operation.
（2）DeSelect all output Functin Description: It is used to close the Select all output function.
7.0.2.4 Disconnect all Command
Function Description: To close all the switching methods.
Press the “Disconnect all” key to close connection to all input and output ports.
7.0.2.5 Memory Function Usage
Function Description: To store and retrieve.
Store Functin Description: The Store Function saves all the present input/output switching
relations to any Locations from #1 to #8 you desired.
ANI-3088
ANI-3088 Matrix Switching System - User Manual
24
A specific example of the Store Function is described below:
Stores all the present input/output switching relations to Location #1. First, select Location
#1，as shown in the figure below:
， then click the save key to save all the
present input/output switching relations to Location #1.
Retrieve Function Description: To retrieve the saved input/output switching relations.
A specific example of the Retrieve Function is described below:
To retrieve the input/output corresponding relations saved in Location #1. First, select Location
#1 as shown in the figure below:
, then click the Load key to retrieve all the
input/output corresponding relations stored in Location #1.
7.0.2.6 Scan Function Usage
Use the mouse to click the Scan key to refresh the AV Matrix operating interface.
7.0.2.7 Options Function Usage
Activation Function:
In the main menu, select Options to prop up the Options window as shown in Figure 7-4（a）
Figure7 -4 （a） Figure7 -4 （b）
Function Description:
Linking Methods: In “ ” select either COM1 port or COM2 port as shown in
ANI-3088 Matrix Switching System - User Manual
25
Figure 7-4（b）; in “ ” select 9600 for signal transmission as shown in Figure 7-4（a）
7.0.2.8 Exit Function Usage
Function Description: To exit the operating software.
7.0.2.9 Other Usages
Displays the presently saved switching status as shown in Figure 7-5 below:
Figure 7-5
When Video/Audio corresponding to Ou tput is open, it shows the Output ports
corresponds to the Video/Audio Input ports; when they are close the word None will be shown in
red in the above table.
8.0 Communication Protocol and Control Command Code
Communication Protocol: Baud rate 9600bps, no odd or even calibration bit address, 8bit
transmission address, 1bit stop address.
Refer to the “Command list.pdf” on the CD-ROM for the command system.
ANI-3088 Matrix Switching System - User Manual
26
9.0 ANI-3088 Matrix System Technical Parameters
Model
Technical Parameters
ANI-3088
Video
Enhancement 0dB
Bandwidth 150MHz (-3dB)，Full Load
Max. Transmission Delay 20nS(±1nS)
Switching Speed 50nS(Longest Time)
Signal Type Component/Composite Video
Video Input
Connector 8 RCA Female
Connectors
Signal Strength 1Vp-p Y Component Video、S-video， Composite Video；
0.3Vp-p R-Y & B-Y Component Video、S-video
Min./Max. Voltage Modulated Signal 0.5V~2.0Vp-p
Impedance 75Ù
Video Output
Connector 8 RCA Female
Connectors
Min./Max. Voltage 2.5Vp-p
Impedance 75Ù
Audio Signal
Input/Output Connectors RCA Female Connectors
Signal Type Stereo, Balanced or Unbalanced
Impedance Input：〉10kΩ
Output：100Ω
Max. Input Level +19.5dBu
Max. Output Level +19.5dBu
Control Type
Serial Control Connectors RS-232，9-Pin Feamle D Type Connector
Baud Rate and Protocol 9600bps, no odd or even calibration address，8bit
Transmission Address，1bit Stop Address
Serial Control Port Structure TX，RX，GND
Control Procedures 《AV Matrix》
Specifications
Power 100VAC~240VAC,50/60Hz，International Auto-Switch
Temperature Storage, Operating Temp.: -40 ℃~+85℃
ANI-3088 Matrix Switching System - User Manual
27
Model
Technical Parameters
ANI-3088
Humidity Storage, Operating Humidity: 10%~90%
Housing Measurements 19”(L) X 11”(W) X 5 ½” (H)
Product Weight 11 lbs.
Median Failure Interval 30,000 Hours
Warranty One year warranty, lifetime maintenance
10.0 Common Problems and Solutions
1. What to do if the matrix front panel keys switching not responsive? ANI-3088
Answer: The matrix front panel keys emplANI-3088 oy scanning testing and require longer response
time. Press the keys for 2 seconds and then release. This way, key switching will be
responsive in operation.
2. What to do if matrix does not display or color display is abnormal after hot plug?
Answer: Switching of the matrix system goes through the IC chips. If the voltage difference
between the input signal equipment and the matrix equipment is too large, hot plug
could easily cause damage to the IC chips. Please turn off power to the system before
plugging or unplugging.
3. What to do if ghosting happens when YPbPr signals output to display?
Answer: Ghosting is often caused either by the projector, inferior cable quality or long
transmission distance. You are advised to adjust the projector or replace with better
quality cable.
4. What to do if loss of color reproduction happens or no video signal output?
Answer: Please check if connectors at both ends of the YPbPr signal cable are correctly
connected.
5. What to do if the serial port (usually refer to the computer serial port) fails to control the
matrix?
Answer: Check that the communication port set by the control software is correctly connected to
the corresponding serial port of the equipment. Also, check if the computer
communication port is in good order.
6. What to do if the corresponding graphics fail to output during matrix switching?
Answer: (1) Check if there is signal on the input end. If there is no input signal, it could be that
the input connection cable is broken or the connector gets loosen. You are advised to
replace the connection cable.
(2) Check if there is signal on the output end. If there is no output signal, it could be that
the cable is broken or the connector gets loosen. You are advised to replace the
connection cable.
(3) Check if the output port number is the same as the controlled port number.
ANI-3088 Matrix Switching System - User Manual
28
(4) If none of the above circumstances happen, it could be internal failure of the product
itself. You must send for repair by qualified technical engineers.
7. What to do if the power LED is not on, LCD has no display and no response in operation?
Answer: Check if the equipment power input is in good contact.
8. What to do if you sensed power leakage during plugging or unplugging of the audio/video
ports?
Answer: It could be that the equipment power is not properly grounded. You must properly
ground your equipment, otherwise product life can easily be shortened.
9. What to do if the LCD displays normally and the communication port has return code but no
graphics or audio output?
Answer: (1) It could be that the audio/video connectors got loosen. Simply replace the
connectors.
(2) It could be the connection cable short-circuited. Simply replace the cable.
(3) It could be the connection cable is broken. Simply replace the cable.
10. What to do if the matrix panel keys and communication ports are out of order?
Answer: Check if the equipment power input is in good contact and the computer
communication ports are in good order. If yes, it could be some internal failure of the
product, please send for repair by qualified technical engineer.
11. What to do if operation and function failure occurred?
Answer: Check if the equipment and the matrix system are in proper connection. If the problem
persists, send the product to the maintenance center for repair.
NOTE:
Do not replace the power cord yourself. If the power cord is damaged, ask your distributor to
send qualified technician to replace it for you.
Shinybow, USA. All rights reserved.
www.shinybowusa.com
Toll Free: 1-(877) SHINY-USA
1-(877) 744-6987
Trademarks:
All the companies, brand names, and product names referred to this manual are the trademarks
or registered trademarks belonging to their respective companies.
Document Version 1.1A
END OF DOCUMENT
Loading...