Shinybow SB-5688 Instruction Manual

M U LT I M E D I A A UD I O A N D V I S U A L

In st ru ction Manual

MODEL : SB-56 88

8x8 HDMI MATRIX SWITCHER

HDMI Matrix Switcher Series

Thank you for purchasing th e SB-5688 HDMI Matrix Switc her. You will find this unit easy to insta ll and highly re liable but it is essenti al th at you read th is manual th ro ughly before att empting to use 8x8 HDMI Matrix switc her.

Version No.: 5688-20120823-001

Part No.: ENCL005688LC MA0

SAFETY INFORMATION

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK),

SERVICEABLE PARTS INSIDE,

NO USER

REFER SERVICING TO QUALIFIED SERVICE PERSONAL.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. .

Caution:

WARNING!

This symbol is intended to alert the user to the presence of uninsulated

of uninsulated “dangerous voltage” within the products enclosure that

enclosure tha may be of sufficientmagnitude to constitue a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operational and maintenance (serving) instructions in the literature accompanying the appliance.

T prevent electric shock do not use this (polarised) plug with an o extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. T prevent electric shock, match wide blade of plug to wide slot, o

fully insert.

Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original

1. factory packing.

Read all documentation before operating your equipment. Retain all documentation for future reference.

3. Follow all instructions printed on unit chassis for proper operation.

4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

5. Make sure power outlets conform to the power requirements listed on the back of the unit.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on

or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit

from the appliance.

7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of

a piece of equipment is not defeated.

8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by

any warranty.

Power down & disconnect unit from mains voltage before making connections.

10.

Never hold a power switch in the ＂ON＂ position.

11. Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices.

12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit,

such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be

Periodically ＂blown free＂ of foreign matter.

Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside.

13.

Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

14.

Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.

15.

Service Information Equipment should be serviced by qualifier service personnel when:

16.

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

IMPORTANT SAFETY INSTRUCTIONS

To insure t he b es t fr om t hi s pr od uct, plea se r ea d th is m an ua l ca refully. K ee p it i n a sa fe p lace fo r fu tu re r ef er en ce .

To reduce t he r is k of e le ct ri c sh ock, do not r em ov e th e co ve r fr om t he unit. No u se r se rv ic ea bl e pa rts ins id e. R ef er s er vi ci ng to quali fi ed p er so nn el .

To reduce t he r is k of f ir e, d o no t ex pose the un it t o ra in , wa te r or e xc essive mo is tu re .

Do not fo rc e sw it ch ed o r ex te rnal conn ec ti on s.

When mo vi ng t he u ni t di sc on nect the se ri al p or t co nn ec ti ons first t he n th e po we r ca bl e an d finally t he i nt er co nn ec ti ng cables t o ot he r de vi ce s.

Do not at te mp t to c le an t he u ni t with chem ic al s ol ve nt s or a er osol clea ne rs , as t hi s ma y da ma ge the unit . Us e a cl ea n dr y cl ot h.

Insta ll at io n of t hi s un it s hould be in a c oo l dr y pl ac e, a wa y fr om source s of e xc es si ve h ea t, v ibratio n, d us t, m oi st ur e an d cold.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS

_____________________________________________________

INTRODUCTION AND PACKAGE CONTENTS

_____________________________________________________

FEATURES

_____________________________________________________

SPECIFICATIONS

_____________________________________________________

EDID FUNCTION - EDID SETUP

_____________________________________________________

EDID FUNCTION - EMBEDDED EDID

_____________________________________________________

EDID FUNCTION - LEARNING EDID

_____________________________________________________

EDID FUNCTION - LEARNING EDID

_____________________________________________________

EDID FUNCTION - EDID SETUP

_____________________________________________________

FRONT PANEL - 1

_____________________________________________________

FRONT PANEL - 2

_____________________________________________________

FRONT PANEL - 3

_____________________________________________________

REAR PANEL

_____________________________________________________

TYPICAL APPLICATION - HDMI IN/OUT

_____________________________________________________

TYPICAL APPLICATION - HDBaseT TX/RX connection

_____________________________________________________

IR REMOTE CONTROL

_____________________________________________________

IR REMOTE CONTROL - IR DATA CODE

_____________________________________________________

IR EXTERNAL INSTALL

_____________________________________________________

CEC FUNCTIONS

_____________________________________________________

RS232 PROTOCOL

_____________________________________________________

LIMITED

_____________________________________________________

PAGE 3SB-5645 INSTRUCTION & OPERATION MANUAL

INTRODUCTION AND PACKAGE CONTENTS

INTRODUCTION

The SB-5688 is high-performance 8x8 matrix routing switcher for HDMI signals. This switcher supports data rates up to 6.75 Gbps, enabling 1080p HDMI formats and UXGA/WUXGA/DVI resolution to any HD display. High Definition Digital signals can be selected and distributed to any 8 outputs simultaneously. The Switcher is certified as being fully HDMI and HDCP compliant, with RoHS,CE,FCC certification. Support high resolution HDMI sources routed to HDMI displays, monitors, projector or audio receivers. The EDID can be selected between eight (8) different modes. Control is provided via Front panel push buttons, IR remote or via RS-232. An RS232 Windows GUI interface is provided for matrix routing.

PACKAGE CONTENTS

1. Main console unit

2. Operating Instructions

3. IR Remote Controller (SW-5688)

4. 19 inch Ear mount bracket (Part # 1U-440L)

5. IR Extender receiver (SB-100)

6. CD Contents: This manual, Windows GUI

7. RS232 Cable

8. Power Supply 12VDC, 5A Universal Type 50/60Hz, 100~230 VAC

PAGE 4 SB-5688 INSTRUCTION & OPERATION MANUAL

INTRODUCTION AND PACKAGE CONTENTS

FEATURES

1. 8x HDMI digital source devices matrix switched to 8x HDMI devices.

2. HDMI digital video w/embedded audio, DVI format and CEC/HDCP 2.0 compliant

3. Seven (7) function key control and worldwide EDID modes for HDTV resolutions.

4. Link speeds of up to 6.75 Gbps (link clock rate of 340Mb Hz), Support HDMI 1.4a 3D formats.

5. Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p

6. Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers/amplifiers.

7. Digital Video TMDS formats Resolutoin up to 1080P-60 with Deep color 36-bit.

8. Digital Audio Support : - Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex,

- DTS, DTS-HD, DTS-HD Master, DTS-EX

- PCM, PCM2, LPCM2..

9. Various User Interface control: ‧Windows based GUI control via RS232 port ‧Front Panel push button ‧IR wireless remote control ‧Third party RS232 controller (via simple ASCII)

10. Support world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK

11. Support EDID modes : Internal modes : AUTO/1080P-2CH/1080P-5.1/1080P-7.1/1080i-2CH/720P-2CH External modes : Passing mode.

12. Automatic scanning input & output status via LED show on front panel.

13. Support preview output port simultaneously output #1.

14. Support IR Remote and IR Extender with distance up to ~ 1000' (300M) Maximum.

15. EDID configuration via Internal modes.

16. Consumer Electronic Control (CEC) switch all open or OFF The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be invoked.

(8)

PAGE 5SB-5688 INSTRUCTION & OPERATION MANUAL

SPECIFICATIONS

Type of HDMI Switcher 8x HDMI inputs To 8x HDMI Outputs Matrix Switcher

HDMI Support HD 1080P-@60Hz, H36-bit Deep color, 3D (1.4a) formats.

HDCP / CEC Support HDCP 2.0 Compliant, CEC Compliant.

Video Bandwidth Double Data Rates:340Mhz, Total 6.75Gbps bandwidth.

Digital Video Support Full HD resolution : 480i / 480p / 720p / 1080i / 1080p

Digital Audio Support Multi Audio Formats 5.1 / 7.1, MAT(MLP)

Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES 6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)

Controls IR Remote Controller

IR External port x 1 (OD 3.5mm Ear phone Jack) Select & Function buttons on front panel RS 232 series interface

Preview output Support 1x preview output port via Output-#1simultaneously

Source Status Automatically Scan Sources Inputs via LED

Function Control Key ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID

Infrared Frequency 38 Khz

IR External Distance ~1000 feet / 300 meters maximum.

HDMI I/O Connector HDMI Type A - SMD 19pin Female Type

Temperature

Dimensions LxWxH=19 ”x 9.85 ” x 1.75 ”(482mm x 250mm x 44mm)

Rack Mount Rack Mount 1RU High 19 ”Rack Mount (with rack mount)

Power Supply DC12V / 5A, Universal world wide Type 50/60Hz, 100~230 VAC

Power Consumption 3880 mA Maximum

(0 C - 38 C)32 F - 100 F Operation

Safety Approvals CE, FCC, RoHS (2002/95/EC).

Product Weight 2.50 Kgs / 4.2 lb

As product improvement is continuous, specifications are subject to change and without notice or liability.

PAGE 6 SB-5688 INSTRUCTION & OPERATION MANUAL

EDID function Setup

EDID FUNCTION

EDID setup

Step 1 .

Step 2 . Press SOURCE #1 or #2

Step 3 . Press the ENTER button

Press the EDID button The display will show the currently selected EDID mode

button row

To change the EDID setup

The button will flash blue and the display will show the current Embedded EDID Status.

To set EDID mode. The switcher will return to operation mode.

Operation will abort if no keys are pressed within 5 seconds.

6.1 Embedded EDID modes Total 8 EDID Modes

Embedded EDID setup

to select Embedded EDID mode or LEARNING mode.

Press

EDID

SOURCE

SOURCE #1 or SOURCE #2

ENTER

Press EDID button : The LCM will show the current EDID status.

ED ID

2. H 24- 3 D, PC M 2CH

Repeatedly depressing the source 1 button will cycle up thru the options. Repeatedly depressing the source 2 button will cycle down thru the options.

Select Embedded EDID : Mode 1 : FSS Mode 2 : H24-3D Mode 3 : H24-3D-M Mode 4 : H36-3D Mode 5 : H36-3D-M Mode 6 : 1280x1024-60Hz Mode 7 : 1920x1200-60Hz Mode 8 : AUTO

DVI-D DVI-D

PAGE 7SB-5688 INSTRUCTION & OPERATION MANUAL

EDID FUNCTION

EDID function for HDMI Matrix Switcher

6.2 RESET EDID Return To Factory default

How to RESET EDID mode

Press

EDID

RECALL

ENTER

6.3 LEARNING EDID

Learning EDID setup

Press

EDID

SOURCE>ENTERDESTINATION

RESET To the FACTORY DEFAULT (1080p-2CH).

Press EDID button : The LCM will show the current EDID status.

Press RECALL button : The LCM will show the RESET EDID.

ED ID

RE SET E D ID

Press ENTER to confirm entries.

The EDID will return to FSS mode and resolution 1080p-2CH.

ED ID

1. F AST S P EED S TAR T

Learning EDID from Destination to Source

Press EDID > DESTINATION Button:

The LCM will be show LEARNING.

ED ID LE ARN I NG

Switcher will LEARN destination EDID and pass the selected source.

NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID.

For example; When the Source has "Learned" the EDID data from a destination, It will save that EDID information into EPROM and the EDID data cannot change. Please select new learning destination to sources or change to one of the embedded EDID modes when you want to remove the learning EDID memory from EPRPM.

PAGE 8 SB-5688 INSTRUCTION & OPERATION MANUAL

+ 16 hidden pages