SD Set Top Box
User Manual
shintaro.com.au
SH-SDST01
Safety Information 4
Introduction
6
System Connection
8
Getting Started
10
Operation
13
System Setup
16
Tools
19
Multimedia Playing
21
Timeshift
23
Troubleshooting
24
Specifications
26
SD Set Top Box
Contents
shintaro.com.au
4
Safety Informations
To reduce the risk of fire and electric shock, do not expose this unit to rain or moisture.
Please read these precautions before operating this unit.
Power cord protection
To avoid any malfunctions of the unit, and to protect against electric shock, fire or personal injury,
please observe the following.
Hold the plug firmly when connecting or disconnecting the AC power cord.•
Keep the AC power cord away from heating appliances.•
Never put any heavy object on the AC power cord.•
Do not attempt to repair or reconstruct the AC power cord in any way.•
Never make or change connections with the power switched on.•
Placement
Avoid placing the unit in areas of direct sunlight or heating appliances, or closed automobiles high
temperature (over 350C) or high humidity (over 90%) or high dust areas as the internal parts may
be seriously damaged.
Non-use periods
When the unit is not being used, turn it off. When left unused for a long period of time, the unit
should be unplugged from the household AC outlet.
No fingers or other objects inside
Touching internal parts of this unit is dangerous, and may cause serious damage to the unit. Do
not attempt to disassemble the unit.
Do not put any foreign object in this unit.
Keep away from water/magnet
Keep the unit away from flower vases, tubs, sinks, etc. If liquids are spilled into the unit, serious
damage could occur. Never bring a magnet or magnetized object near the unit.
Stacking
Place the unit in a horizontal position, and do not place anything heavy on it.
5
Condensation
Moisture may form on the lens in the following conditions:
Immediately after a heater has been turned on in a steamy or very humid room when the •
unit is suddenly moved from a cold environment to a warm one.
If moisture forms inside this unit, it may not operate properly. In this case, turn on the power •
and wait about one hour for the moisture to evaporate.
If there is noise interference on the TV while a broadcast is being received
Depending on the reception condition of the TV, interference may appear on the TV monitor while
you watch a TV broadcast and the unit is left on. This is not a malfunction of the unit or the TV.
Recycling
This symbol on the product or in the instructions means that your electrical and electronic
equipment should be disposed of at the end of its life separately from your household waste.
For more information, please
contact the local authority or your retailer where you purchased the product.
Active Antenna Off
11
INFO: Operation guide
Channel Manager
Installation
Configuration
Software Upgrade
Factory Default
Version
Digital TV
Installation
Press “MENU” button to enter the MAIN MENU.1.
Press “OK” button to highlight “Digital TV”.2.
Press “UP” or “DOWN” button to select the “Installation”, and press “OK” 3.
button to confirm.
Auto Search
Press “MENU” button to enter the Main Menu.1.
Press “DOWN” button to Select the Installation.2.
Press “OK” button to “Auto Search”.3.
S.No. TV Channel
Channel Search
S.No. Radio Ch annel
Channe l xx UHF xxxxxxKHz/ 8M
Prog ress
86%
INFO: Operation guide
Area Search
Manual Se arch
Auto Se arch
Installation
INFO: Operation guide
Auto Se arch
Manual Se arch
Area Se arch
Installation
12
Manual Search
Select the Manual Search and press 1.
“OK” button to confirm.
Press “LEFT” or “RIGHT” button to 2.
select the desired option.
Press “OK” button to confirm.3.
Area Search
Press “UP” or “DOWN” button to highlight the “Area Search” .1.
Press “OK” button to enter the “Area Search”2.
The Area Search window will displayed. Press the numeric buttons to 3.
“Start Freq (KHZ)”
Press “DOWN” button to “End Freq (KHZ)” and enter a frequency.4.
Press “DOWN” button to “BandWith”,Use “RIGHT” button to choose the 5.
“BandWidth”.
Press “OK” button to “Area Search”.6.
Channel Number
21
INFO: Operation guide
Manual Search
Freq(KHz)
BandWidth
474000
8M
21
22
23
24
25
26
27
28
29
Streng th 20%
Quality 2%
474000
Start Freq(KHZ)
474000
End Freq(KHZ)
INFO: Operation guide
Area Search
BandWidth
8M
You can change the frequence and bandwidth
by ch oosing the "Area ".
Select the con
uration menu, set the "Area"
at the "System Setup " or choo se th e Area when
the initialization of the STB.
NOTE
13
Operation
Channel Manager
Changing Channel
Selection by Channel list1.
Press “OK” button to enter the “QUICK •
SELECT”.
Press “UP” or “DOWN” button to select •
channel .
Press “INFO” button to display the navigation •
window.
Perform the correlative operation with the guide. •
Selection by EPG2.
Press “EPG” button to the “EPG” •
window
Press “UP” or “DOWN” button to •
select channel.
Press “INFO” button to display the •
navigation window.
Perform the correlative operation with •
the guide
Selection by Number3.
Enter the channel list number directly by remote control to select desired •
channel.
INFO: Operation guide
QUICK SE LECT
None
0104 Channel Name
0100 Teletext on 4
0083 Sky Spts News
0082 Sky News
INFO: Operation guide
S.No. Channel Name
INFO: Operatio n guide
Daily Mode
Date 01/01/2000
Time 02:10:21
01/01/2000(Saturday)
0082 Sky New
0075 CITV
0032 E4+1
0029 E4
0028 ITV4
0014 More4
14
Organize Channel
Press “MENU” button to enter “Main Menu”1.
Press “OK” button to enter “Channel 2.
Organizer”
Press “UP” or “DOWN” button to a 3.
channel for “Organize selection”
Press “INFO” button,then perform the 4.
correlative operation with the guide
RED button: For fav selection
GREEN button : For move selection
YELLOW button: For lock selection
BLUE button: For delete selection
Channel Sorting
Press “MENU” button to enter “Main Menu”1.
Press “OK” button twice to enter Channel Manager2.
Press “CH+/CH-” button to select “Channel Sorting”3.
Press “OK” button to enter the “Channel Sorting” window4.
Press “INFO” button,then do the correlative operation with the guide5.
INFO: Operation guide
Channel Organizer
0001 BBC ONE
0002 BBC TW O
0007 BBC THREE
0011 SKY THERR
0012 UKTV History
0030 CCBC Channel
England Rowridge 666000KHz/8M
S.No Channel name Fav Move Lock Del
INFO: Operation guide
Channel Sorting
S.No Channel Name Freq Bandwidth
0102 Teletext cars 546000k 8M
0500 TPS 546000K 8M
0723 talksport 562000k 8M
0724 3C 5 62000K 8M
0725 Premier Radio 562000K 8M
First Option A ll Area
Second Option Scramble
Third Option LCN-
Greece
Austrialia
All Area
NOTE
The default pa ssw ord for
Lock and Deletion is "0000".
The super p assword is "8888".
15
Channel Grouping
Press “MENU” button to enter the 1.
Main Menu.
Press “OK” button twice to enter 2.
Channel Manager.
Press “UP” and “DOWN” button to 3.
highlight “Channel Grouping”.
Press “OK” button to select the 4.
“Channel Grouping”.
Press “UP” and “DOWN” button to 5.
select channel.
Press the numeric button to group the selected channel.6.
Press “INFO” button, then choose the correlative operation with the guide.7.
Delete All
Press “MENU” button to enter the 1.
“Main Menu”.
Press “OK” button twice to select the 2.
“Channel Manager”.
Press “UP” and “DOWN” button to 3.
highlight “Delete All”
Press “OK” button. A password 4.
window will display. Enter the
password. The default password is “8888”.
Press “INFO” button, then choose the correlative operation with the guide.5.
1 None
2 News
3 Scien
4 Sport
5 Movi
6 Kids
7 Music
8 Fashi
S.No Channel Name Fav Group
INFO : Operation guide
Channel Grouping
0102 Teletext Cars
0500 TPS
0723 talkSPORT
0724 3C
0725 Premier Radio
0728 Heart
INFO: Operation guide
All TV Channels
All Radio Ch annels
Delete All
16
Record
You can record the current TV program to the Hard Disk by pressing the
“RECORD” button. Press the “stop” button to display an interactive window
and choose to stop it or not.
Note: Be sure the hard disk has enough space to record. A partition error will
appear if the STB loses power while the recording. You can repair or format
the hard disk to resolve. The STB only recognises FAT format on HDD’s.
System Set-Up
Many aspects of your STB can be set to reflect your circumstances and
preference. The Configuration menu screen is accessed from main menu. The
Configuration contains OSD, TV, System Setup, Time, Wakeup Timer, Parental
Lock. All the settings will be saved after quitting the main menu.
OSD Set up
This menu allows you to set the OSD information based on the viewer
preference.
Enter the OSD menu, press “LEFT” or “RIGHT” button to select the desired 1.
option.
Press “UP” or “DOWN” button to highlight the next option.
2.
Press “OK” button to set.3.
OSD
Theme1
INFO: Operation guide
OSD
Time on OSD
OSD Timeout
OSD Trans
OSD Language
MP4 Su btitle Langua
MP4 Su b codepage
1st Audio Language
2nd Audio Language
ON
1
10%
English
English
8859
English
English
Themel
Theme2
Theme3
Theme4
Theme5
NOTE
Wh en the"Time on OSD "i s on , the function of subtitle is
automatic o
.
CVBS
18
Wakeup Timer
This menu allows you to set the Wakeup
Timer information based on the viewer
preference. There are 3 ways to enter the
Wakeup Timer menu.
Entering through the main menu:
Press “MENU” button to enter the
“Main Menu”.
Press “OK” button to enter “Digital TV”.
Press “UP” and “DOWN” button to highlight “configuration”.
Press “OK” button to enter “configuration”.
Press “UP” and “DOWN” button to select “Wakeup timer”.
Press “OK” button to enter the “Wakeup Timer” menu,
Press “LEFT” or “RIGHT” button to select the desired option.
Press “UP” or “DOWN” button to highlight the next option.
Press “OK” button to set.
Entering through the EPG:
Press EPG button to enter the EPG window.
Press “LEFT” to enter the event.
Press “UP” and “DOWN” button to select event.
Press “BLUE” button to enter the “Wakeup Timer” menu.
Entering through the BLUE button:
Press “BLUE” button can enter Wakeup Timer menu directly.
Timer NO
1
INFO: Operation guide
Wakeup Timer
Timer Mode
Wakeup Mode
Wakeup Chan nel
Wakeup Date
On Time
Duration
Default Partition
O
Message
BBC FOUR
xx/x x/xxxx
01:42
00:00
/sda 1
1
2
3
4
5
6
7
8
NOTE
When you complete your setup,
you must exit all menus ,then
system will save your setup.
19
Parental Lock
This menu allows you to set the TV
information based on the viewer preference.
Enter the Parental Lock menu1.
Input a correct password using the 2.
numeric buttons
Tools
Software Upgrade
The software may be upgraded via USB
Press “MENU” button to enter the “Main Menu” window1.
Press “OK” button to select the “Digital TV”2.
Press “UP” or “DOWN” button to select 3.
“Software Upgrade”
Press “OK” button to enter the download 4.
route, choose the correct upgrade file
Press “OK” button to upgrade5.
Users may also download and upload channel data via USB
Highlight “Download channel data” item, press “OK” button to download 1.
channel list named “channeldata.bin” in USB Device
Highlight “Upload channel.dat”, press “OK” button to enter USB Device 2.
and select file “channeldata.bin” then press “OK” button to upload channel
list to flash.
Enter password
Parental Lock
Enter Old Password
Enter New Password
Con
rm New Password
NOTE
The default password for
Lock and Deletion is "0000".
The super password is "8888".
1.Read Date
[OK]
USB Upgrade
2.Check Checksum
[OK]
3.Update FLASH
4.Restart System
3.Update FLASH
20
Factory Default
This function allows you to re-set the STB back
to factory settings, clearing all existing channels.
Enter “Digital TV” menu, select “Factory 1.
Default”, press “OK” button. You are asked
to input a password.
Input a correct password using the numeric 2.
buttons (the default password is “8888”). A
confirmation window is displayed.
Select “Yes” to return back to factory 3.
settings and clear all channels. Select “No”
to cancel.
Press “EXIT” button to exit.4.
Version
The Version menu can display some parameters of this STB.
Enter the “Digital TV” menu, select the Version, press 1.
“OK” button. The Version window will be displayed.
Games
This function allows you to play games on the STB.
Press “MENU” button to display the Main 1.
Menu, move the cursor to select the Games
item, press “OK” button to confirm.
Press “OK” button to enter the “Native 2.
Games”. Press “EXIT” button to exit.
INFO: Operation guide
Channel Manager
Installation
Configuration
Software Upgrade
Factory Default
Version
Digita l TV
Enter password
?
Do you want to perform
factory default?
?
No
Yes
Version
H/W version DVB-T Vx.x
S/W version xxxxxx_V x.x
F/W version xxx_xxx_xxxx_xxxx_xxx
Checksum xxxxxxxx
INFO: Operation guide
Box Man
Tetris
Hit Rat
Native Games
21
Multimedia Playing
This function allows you to play video, audio or photo files from USB port.
Movie Playing
Press “MENU” button to display the “Main Menu” 1.
window.
Select “Movie”. Move the cursor to enter the route of 2.
the desired video files.
Press the “OK” button to play the desired video 3.
files.
Music Playing
Press “MENU” button to display the “Main 1.
Menu” window.
Select “Music”. Move the cursor to enter the route 2.
of the desired audio files.
Press the “OK” button to play the desired audio files.3.
Photo Playing
Press “MENU” button to display the “Main 1.
Menu” window.
Select “Photo”. Move the cursor to enter 2.
the route of the desired photo files.
Press the “OK” button to play the desired 3.
photo files.
Movie
0001/sda
Music
0001/sda
Photo
0001/sda
NOTE
Press "RED " button once, and then press or button ,
can zoom the photo at 2,3,4 ,1/2,1 /3,1/ 4.
22
Disk Manager
Press “MENU” button to display the “Main 1.
Menu” window. Select “Disk Manager”. The
Disk Manager window will displayed.
Move “UP” or “DOWN” button to select the 2.
desired files. Press the “Green” button to
select play, delete one or delete all of the
files
Partition-Format
Press “MENU” button to display the “Main Menu” window.1.
Select “Partition-Format”. Press the “OK” button to enter the Partition-2.
Format menu. Move the cursor to highlight the desired HDD.
Press the “OK” button to format the partition.3.
Note: When playing the multimedia files, make sure the USB is connected
to the STB. When “Movie” is selected, the STB can play the video files or the
recorded files. When “Music”/”Photo” is selected, the STB can play the audio
files or the photo files. The Disk Manager can play the recorded files only.
Disk Manager
00 01 BBC NEWS 24(06)
00 02 E4 +1(0 80317_1
00 03 SK Y THREE(0604
00 04 SK Y THREE(0604
00 05 SK Y THREE(0604
00 06 SK Y THREE(0604
00 07 SK Y THREE(0604
00 08 SK Y THREE(0604
Play/Del/R ename
Play
Delete th e select file?
?
No
Yes
Partition-Format
0001/sda
Do you want to format
this partition?
?
No
Yes
23
Timeshift
Plugging an external Mass Storage Device to the USB port gives you access
to Time Shift a broadcast programme.
Pause a broadcast programme and continue watching it later (Time Shift)•
Record Time Shift•
When the space available on the Mass Storage Device runs out, recording •
operation of broadcast will stop
Timeshift
Initiate:
Time Shift can be done in viewing mode by pressing the “TIME SHIFT “
button.
Trick Modes:
During playback, it is possible to perform the following actions :
Press “PLAY/PAUSE “ button to play/pause the playback•
Press “FORWARD “ button to fast forward the playback•
Press “BACKWARD “ button to rewind the playback•
Stop the Time Shift:
Press “EXIT” button to stop Time Shift. Then, a confirmation window appears.
You are asked to save buffer or not:
Select Yes to record Time Shift buffering
Select No to viewing mode displaying the present
program
PAUSE -00: 03:4 4
Do you want to save
buffer?
?
No
Yes
24
Troubleshooting
In some regions, the digital terrestrial signal may be weak. Ensure you use a
quality antenna to maximise reception.
Problem Possible cause What to do
Standby light not lit Mains lead unplugged
Mains fuse blown
Check mains lead
Check fuse
No signal found Aerial is disconnected
Aerial is damaged/
misaligned
Out of digital signal area
Check aerial lead
Check aerial
Check with dealer
No picture or sound Tuned to digital teletext
channel
Tune to another channel
Scrambled channel
message
Channel is scrambled Select alternative
channel
No response to remote
control
Receiver off
Handset not aimed
correctly
Front panel obstructed
Hand set batteries
exhausted
Plug in and turn on plug
Aim handset at front
panel
Check for obstructions
Replace handset
batteries
Forgotten channel lock
code
Re-install channels to
cancel
channel lock
25
Forgotten menu lock
code
Contact help line
The remote control will
not operate your STB
(1) The batteries in your
remote control need
replacing
(2) There is an
obstruction blocking the
signal path between the
remote control and the
box.
(1) Replace the batteries
(2) Check that there is
nothing in the way of
the path between the
remote control and the
receiver
After moving the STB to
another room you
find you are no longer
able to receive digital
reception
The aerial feed former
new point may come
through a distribution
system which may
reduce the digital signal
now received by the
box.
Try a direct feed from
the antenna
RCA output V/R/L x1
28
support@shintaro.com.au
Loading...