Page 1
V EXTERNAL CALIBRATION
IMPORTANT: The scale was professionally calibrated before
shipment. It does not recalibrated before use and will not usually
require calibration during its lifetime. However some advanced
users who seek optimum accuracy may wish to calibrate the scale
periodically to maintain perfect accuracy. Incorrect calibration can
occur if you do not follow the steps exactly
1 Press to turn on the scale for warm-up 1-2 seconds
2 Press
to show “0.0” , then press for 3s, it will
show “CAL 0” and “LOAD –XXX g”
3 Place a weight which value equal to the number on the tr ay
(the showed number is 1000g ,that means you should place a
1000g weight on the tray),,it will display the weight value if
success, then return to the normal weighing.
NOTE: If your scale still does not read accurately, it means that
the calibration is failed and please follow the above steps to
re-calibration slowly.
Please do it on a very stable and flat surface!
VI BASIC SPECIFICATION
Tray
Square size: 155x155mm / Round size : Φ125mm
Display Mode Large LCD display , backlight (optional)
Power supply 4 batteries , or DC adaptor (6V/300mA)(Optional)
Operation T em p.
0-40℃
ELECTRONIC BALANCE
SHINKO GS SERI
Operation Manual
VIBRA SCALES JSC
Page 2
III EXPLANATION OF SYMBOLS
: negative value O : stable /zero indicator
: units indicator
g : unit
: low battery indicator PCS : count indicator
IV OPERATIONS
1 Turn on the scale
Press
to turn on the scale. The scale will show
“88888”and other indicators ,and then it will be ready for use.
2 Start weighing
A. Weighing without container
If the reading is not “0” or the zero indicator isn’t displayed,
press
to display “0” and the zero indicator appears, then the
place objects on the tray, when the stable indicator appears, the
value displayed is the weight of the objects.
B Weighing wit h container
Place an empty container on the tray ,press
to display “0”
after the stable indicator appears, then place the objects into
container ,after stable, the value displayed is the weight of the
objects.
3 Counting
Turn on the scale and put on the integral sample, Press
to
show S-10 ,press
again to select a parameter of
S-10/20/50,after a few seconds it begin to counting mode. Press
to exit.
4 Power-off and Automatic power-off
A Press
directly to turn off the scale
B If your scale have auto-power off function before shipment,
it will auto turn off after non-operation for 3 seconds.
I NOTICE
Precautions Before Using the scale
The scale should be used in a stable environment without
ventilation and corrosion , extreme in temperature and humidity.
These factors can affect the accuracy and performance of the scale.
Operation Advices
■ The better environment, the more in favor of normal
weighing
■ Allow sufficient warm up time. 1-2 minutes is necessary
■ Do not mismatch battery and please install all batteries at the
same time.
■ Take out all batteries when non-operation long, it can avoid
the damage of scale.
■ Do not overload the scale, overloading the scale will damage
the sensor and void your warranty.
■ Handle with care. Although this scale is designed to be quite
durable and firm, rough treatment may damages the internal
sensor permanently.
■ Remove the object immediately after finishing weighing. It
can prolong the life-pan and accuracy of the scale.
II KEYPAD FUNCTIONS
1 Power Switch
2
Select the unit, units optional refer to panel
3
Count
Page 3
4 Reset the scale to zero or tare
Model number Capacity Division Pan Size (mm)
SHINKO GS600 600g 0.1g
155 x 155
SHINKO GS1 1kg 0.1g
155 x 155
SHINKO GS2 2kg 0.1g
155 x 155
SHINKO GS3 3kg 0.5g
155 x 155
SHINKO GS3001 3kg 0.1g
155 x 155
SHINKO GS6 6g 1g
155 x 155
THINH PHAT SCALES JSC
VIBRA SCALES JSC
VIET NAM SCALES JZC
Loading...