Shimpo Instruments all products Accessories Catalog

Attachments

Attachment Description Capacity

Small Pin Grip Ideal for gripping fine wires and filaments; three ranges for
FG-M6PIN05 checking samples of .02", .04", .08" (0.5, 1 and 2 mm) thick.
FG-M6PIN1
FG-M6PIN2

22 lb (11 Kg)

Fine Point Grip Perfect for testing fine and medium gauge wire, ribbon,tape 30 lb (15 Kg)

FG-M6FPG3 and paper. Two jaw widths and load capacities are available;

FG-M6FPG8 both can handle material thickness up to .04" (1 mm). 60 lb (30 Kg)

Film Grip These heavy-duty, spring-loaded grips have serrated jaws for
FG-M6FLM20 handling samples up to .39" (10 mm) thick and .79" (20 mm) 100 lb (50 Kg)
FG-M6FLM50U or 1.97" (50 mm) wide.

Jacob’s Chuck Grip Designed for testing low gauge wire and rigid rods; accepts
FG-M6JAC5U material diameters from .02" (.05 mm) to .20" (5 mm).

Flat Chuck Tensile Grip Each serrated gripping face is .79" (20 mm) square and can
FG-M6FTG20U accept samples up to .79" (20 mm) thick.

Spool Grip Ideal for hard-to-hold items like thread, filaments,etc. The
FG-M6SP010U sample is wrapped around the spool, anchored by friction.

Tape Grip Self-tightening lever action makes this fixture perfect for testing
FG-M6TAP30U rubber, tape and paper.

Wedge Grip Two capacities for lighter and heavier loads; spring-loaded
FG-M6WDG50U jaws automatically close on the specimen and tighten as
FG-M10WDG500U tension is applied. Ideal for testing wires, strip material and

plastic tape or films.

Heavy-Duty Tensile Grip Manually tightened jaw faces can accept samples 1.25”
FG-M10TEN7U (31.75 mm) wide and .25” (6.35 mm) thick. Contact faces 500 lb (250 Kg)
FG-TEN7B are serrated hardened tool steel.

Clevis Grip Odd shaped parts, punched samples or tension springs are
FG-M10CLV10U easily secured and tested. Concave shape to pins assures
FG-CLV10B centering under load. Throat clearance with pin is .5" (12.7 mm)

and can easily accept samples up to .375” (9.65 mm) wide.

.12" (3 mm)

.31" (8 mm)

100 lb (50 Kg)

100 lb (50 Kg)

100 lb (50 Kg)

100 lb (50 Kg)

100 lb (50 Kg)

500 lb (250 Kg)

500 lb (250 Kg)

Cord and Twine Grip A unique figure 8 wrap of specimen assures a center break and
FG-M10TWN500U non-locking pins permit quick installation and release.
FG-TWN500B Throat and pin clearance is .375” (9.65 mm) wide with the

throat width being .5" (12.7 mm).

Fabric Grip Eccentrically mounted, serrated roller grip allow for self­ FG-M10FAB80U tightening of specimens up to 3" (76.20 mm) wide and .25" 500 lb (250 Kg)
FG-FAB80B (6.4 mm) thick.

Adhesive Test Plates Samples up to 3" (76.20 mm) in diameter can be tested with
FG-M10ADHE3 hardened tool steel detachable faceplates. Ball socket mounting

screws in both grips assure parallelism and perpendicularity
to force when load is applied.

Wire Terminal Test Fixture

FG-M6WTER100 connections. The upper grip consists of a self-aligning wheel

Compression Plates 50 and 100MM steel compression plates for top load testing, 100 lb (50 Kg)
FG-M6COMP50U large sample compression or crush testing, with polished finish. 500 lb (25 Kg)
FG-M6COMP100U 50mm & 100mm plates available in M6 or M10 threading.
FG-M10COMP50U
FG-M10COMP100U

Designed specifically to test the strength of wire/terminal

with nine equally spaced slots of various terminal shank sizes; 100 lb (50 Kg)
an eccentrically mounted, self-tightening bottom grip secures
the wire on the other end.

500 lb (250 Kg)

500 lb (250 Kg)