SHIMPO DT-5TS User Manual

DT-5TXR / DT-5TS

DIGITAL PANEL MOUNT TACHOMETER

Instruction Manual

Contents

Standard Accessories ................................................... 3

Features and Benefits ..................................................3

Important Safety Precautions ...................................... 3

Display and Keypad ...................................................... 4

Rear Panel and Terminals ............................................. 5

Set-Up.......................................................................... 5

Power .....................................................................5

Sensor Connection..................................................5

DT-5TXR

DT-5TS

Congratulations on your purchase of a Shimpo DT-5TXR
or DT-5TS digital panel mount tachometer. Whether

measuring RPM or a complex function, we trust you will
enjoy many years of professional results.

Please read the entire instruction manual thoroughly
before initial set-up and operation; the information

contained herein will aid in operating your Shimpo
DT-5TXR/DT-5TS panel meter safely and with excellent

results.

If you have any questions regarding our product(s), call
your local Shimpo representative or contact Shimpo

directly for assistance.

Self-Test ................................................................... 5

Panel Installation ..................................................... 6

Factory Settings ........................................................... 6

Parameter Settings..................................................6

Function Settings .................................................... 6

Operation .................................................................... 7

Mode Operation Selection...................................... 7

Setting Mode Parameters ....................................... 7

Mode -01- (RPM or Rate Measurement) .............. 7

Mode -02- (Elapsed Time

Measurement/Monitoring).................................. 9

Mode -03- (Process Time Measurement)............ 10

“How to Operate” Teaching Feature .....................10

Setting High and Low Limits .................................11

Setting Functions .................................................. 11

Memory Feature.................................................... 12

Setting Examples ................................................... 13

Modules Available for DT-5TXR...................................15

DT-5TXR with DOP-CPTR Module ...........................15

DOP-TRTR Module..................................................16

DOP-FVTR or DOP-FVC Module...............................16

DOP-BCD Module ..................................................18

Dimensions and Specifications ...................................19

Troubleshooting ........................................................ 20

Warranty .................................................................... 20

2

If any damage is apparent, do not unpack the panel
meter. Notify the shipping carrier immediately for

damage claim instructions. Refer to the label to confirm
model number ordered and record serial number for

future reference.

Items included with the DT-5TXR or DT-5TS are:

Important Safety PrecautionsStandard Accessories

Confirm that the unit is turned OFF when
connecting or disconnecting the unit to a

sensor.

Never use wet hands when connecting or
disconnecting a sensor or checking the unit.

• Mounting adapter, 2 pieces (attached)

• Mounting screw, 2 pieces (attached)

• Decal sheet

• Front button protective cover (attached)

Features and Benets

The DT-5TXR/DT-5TS panel meter offers many features and
benefits including:

• Accepts a wide range of ppr (1-9 , 999) to
accommodate any sensor commonly found in the
field

• Wide range of AC voltage input (85 – 264 VAC 50/
60 Hz) eliminates duplicity of models or changing
of transformers

• Scalable; able to measure in various units

• Standard 1/8 DIN mounting enables easy mounting

while saving time

• Accepts modules (DT-5TXR only) which provide
different types of outputs, i.e. analog voltage,
analog current (4-20 mA), relay closures (set points),
BCD output and others for
recording purposes or data analysis

Always use the correct voltage (AC type: 85­264VAC, DC type: 9-35VDC).

Do not position the signal wires and power
cord near each other.

Remember to check terminal connections, as
they may become loose due to vibration.

Do not use or store unit in extreme
temperatures; normal operating temperature

is 32-113ºF (0-45ºC).

Do not use or store unit in oily, dusty, or high
humidity areas.

Do not use chemicals to clean the case; use a
damp, soapy cloth.

Do not operate the unit in a location where
electrical noise, static electricity or excessive

vibration is present.

3

Display and Keypad

NOITCNUFNOITANGISED.ON

noitcnuf yromem setavitcAnottuB yromeM.1

detavitca si noitcnuf yromem nehw NOrotacidnI yromeM.2

edom putes gnilacs kciuQnottuB gnihcaeT.3

edom putes gnilacs kciuq ni nehw NOrotacidnI gnihcaeT.4

putes retemarap roFnottuB retemaraP.5

putes noitcnuf roFnottuB noitcnuF.6

snoitcnuf s’retemarap steSnottuB teS.7

noitceles edoMnottuB edoM.8

laced rof aerAlaceD tinU.9

tnemerusaem fo stinu syalpsiDyalpsiD yramirP.01

11. Secondary Display B Secondary display

snoitcerroc rof ecapskcaBnottuB ecapskcaB.21

13. Negative Sign/Decimal Point Button Negative sign setting/decimal point shift

snoitcnuf suoirav roFnottuB ciremuN.41

15. Secondary Display A Secondary display

tneserp si langis nehw gniknilBrotacidnI langiS.61

17. Comparator Indicator Indicates comparator condition

4

(

)

Rear Panel and Terminals

Set-Up

Power

Refer to diagram 1 (right) for location of the terminals.

AC Models

Apply 85 – 264 VAC, 50/60 Hz between terminals 1 and 2.

DC Models

Apply 9 –35 VDC between terminals 1 (positive) and 2
(negative) on the main terminal block.

NO. DESIGNATION

1. Lower Module Latch

2. Upper Module Latch

3. Lower Module Connector

4. Upper Module Terminal Block

5. Rear Cover

6. Main Terminal Block

After proper power (AC or DC) is applied to the unit
and before any sensor is connected, the LED display

will light up.

diagram 1

Sensor Connection

Use the chart below to determine how to connect the
DT-5TXR/DT-5TS to Shimpo sensors:

SENSOR

MP-10 -40° - +221°F (-40° - +105°C

3030AN -100° - +225°F (-73° - +107°C)

3070A* -100° - +200°F (-73° - +104°C)

Contact Closure Relay or Solenoid Jumper 5 and 6 Connect 6, zH 02zH 02<9

BI2-S12 Open Collector NPN Proximity 4,6, F°851+ - °31-zHk 2 – 09 (-25° - +70°C) 100 kHz

* For hazardous locations

TYPE

Rotary Pulse Generator 30 kHz

Retro-Reflective

Magnetic

TERMINAL NUMBER FREQUENCY or RPM RANGE OPERATION TEMP ERATURE FILTER

4,6,9

3,8,9

3 – 0C006-B1ER ,000 RPM
1 – 0C0001-B1ER ,800 RPM

MPR 000,5 – 0C06-B1ER

)C°05+ - °01-(F°221 - °419,7,4

F°131+ - F°31-zH 333 – 0556-SCM

-25° - +55°C)100 kHz

10 kHz

zHk 03)C°07+ - C°02-( F°851+ - F°4-zHk 8 – 09,7,4ytimixorP gnihctiwS eriw-3G-ES
zHk 01)C°06+ - °55-( F°041+ - °86- zHk 1 – 08,4ytimixorP gnihctiwS noN eriw-2G-2JD

Self-Test

To confirm that all display LEDs are operating correctly, a self-test is recommended (see “Display and Keypad” section
for button locations):

zHk 001)C°9.84+ - °03-( F°021+ - °22-zH 052 – 0526-SCM

1. Press and hold the MODE button for approximately 3 seconds; “0” will begin flashing until “-01-” appears on the
display.

2. Press any of the lower buttons (NUMERIC, NEGATIVE SIGN/DECIMAL POINT, BACKSPACE) to scroll through “-02-”,
“-03-” and “-04-” until “-99-” appears on the display.

3. Press the SET button to begin the self-test. The entire display will cycle through all digits, arrows, dashes, colons,
decimal points, etc.

4. When satisfied that all LED’s are operational, press the SET button to exit.

5

Panel Installation

_ _

_ _

_

_

_

_

_ _ _ _

y

_

_

_

_

Install the DT-5TXR/DT-5TS on panel as follows:

1. Confirm that the panel thickness is 0.047” - 0.197” (1.2 mm - 5 mm).

2. Remove the two mounting adapters (provided) from the DT-5TXR/DT-5TS (diagram 2).

3. Install a water-resistant gasket on the panel (see diagram 3 & 4).

4. Hold the panel meter in a horizontal position, insert it into the cut-out and press against gasket (diagram 5).

5. Replace the two mounting adapters (diagram 6).

6. The DT-5TXR/DT-5TS is secured on the panel by using the two mounting screws (provided) (see diagram 7).

3 margaid2 margaid

Factory Settings

The following charts reflect the default parameter and function settings as programmed by the factory:

Operating Mode -01- (RPM or Rate Measurement)

PARAMETER DESCRIPTION

1 Pulses per rev olution
2 Sensing RPM _ 01000 1,000 RPM
3 Display units 1000 1,000
4 Update time _ 1.0 _ 1 second
5 Display “Hold” after input signal ceases

6 Input filter

DEFAULT FACTORY SETTING

DISPLAY

0001 1 ppr

006.0

10

MEANING

6 seconds

10 kHz

diagram 4

7 margaid6 margaid5 margaid

6

FUNCTION

1 The 2nd HI and 2nd LO limit setting 0 0 0 0 0 0 0
2 Hysteresis of 1st HI and 1st LO set _ _ _ _ 0 0 0
3 Secures the 1st HI and 1st LO set

4 Output activation of any set limit
5 Selection of secondary displa
6 Main display shows 0 below this no. setting 0 0 0 0 0 0 0
7 Averages the sensor output fr equency _ 0 _ None
8 Deceleration to ZERO display value

Output modules (DT-5TXR only)

10 Logic of BCD output _ 0 _ Negative-true logic
11 Analog output value 0 0 1 0 0 0. 1000
12 Minimum value of analog output 0 0 0 0 1 0. 10
13 Update time for analog output

14 Offset for analog output

DESCRIPTION

DEFAULT FACTORY SETTING

DISPLAY

0

0 0 0 seconds

0 _1st HI and 1st LO limit set

_ 0 _

0

0 0 0.0 0%

Not secured

About 10 msec

Off