Page 1
(English)
DM-CS0004-04
Dealer's Manual
Cassette Sprocket
(11-speed)
CS-9000
CS-6800
CS-5800
Page 2
IMPORTANT NOTICE
The following instructions must be observed at all times in order to prevent personal injury and physical damage to
equipment and surroundings.
The instructions are classified according to the degree of danger or damage which may occur if the product is used
incorrectly.
DANGER
Failure to follow the instructions will result in death or serious injury.
WARNING
Failure to follow the instructions could result in death or serious injury.
CAUTION
Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.
•
This dealer's manual is intended primarily for use by professional bicycle mechanics.
Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the
dealer's manuals.
If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your pla
of purchase or a local bicycle dealer for their assistance.
•
Make sure to read all instruction manuals included with the product.
•
Do not disassemble or modify the product other than as stated in the information contained in this dealer's manual.
•
All dealer's manuals and instruction manuals can be viewed on-line on our website (http://si.shimano.com).
•
Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a
dealer.
For safety, be sure to read this dealer's manual thoroughly before use, and follow it for correct use.
ce
2
Page 3
TO ENSURE SAFETY
WARNING
•
When installing components, be sure to follow the instructions that are given in the instruction manuals.
It is recommended to use genuine Shimano parts only. If parts such as bolts and nuts become loose or damaged, the bicycle may
suddenly fall over, which may cause serious injury.
In addition, i
cause serious injury.
•
•
After reading the dealer's manual thoroughly, keep it in a safe place for later reference.
f adjustments are not carried out correctly, problems may occur, and the bicycle may suddenly fall over, which may
Be sure to wear safety glasses or goggles to protect your eyes while performing maintenance tasks such as replacing parts.
NOTE
Be sure to also inform users of the following:
•
If the chain keeps coming off the chainrings during use, replace the chainrings and the chain.
•
Products are not guaranteed against natural wear and deterioration from normal use and aging.
•
For maximum performance we highly recommend Shimano lubricants and maintenance products.
For Installation to the Bicycle, and Maintenance:
•
Always use CS-9000/6800/5800 in combination with CN-9000/6800/CN-HG600-11. Other chains cannot be used because the
dimensions do not match.
•
The gears should be periodically washed with a neutral detergent. In addition, cleaning the chain with neutral detergent and
lubricating it can be an effective way of extending the life of the gears and the chain.
•
Always use the recommended combination of gears.
The actual product may differ from the illustration because this manual is intended mainly to explain the procedures for
using the product.
3
Page 4
INSTALLATION
For each sprocket, the surface that has the group mark should face
outward and be positioned so that the wide parts of the gear
projections on each sprocket and the A part (where the groove
width is wide) of the freewheel body are aligned.
< CS-9000: 11T- 23T, 11T- 25T, 11T- 28T, 12T- 25T, 12T- 28T >
Sprocket spacers
Wide part
A
The groove has only
one wide section.
Lock ring
1
2
Number
1 23 11S 23A
2 21 11S 21A 23 11S 23B 25 11S 25B
3 19 11S 19A
5 17 11S 17A 17 11S 17A 19 11S 19C
6 16 11S 16A – 16 11S 16A – 17 11S 17B –
7 15 11S 15A – 15 11S 15A – 15 11S 15A –
8 14 11S 14A – 14 11S 14A – 14 11S 14A –
9 13 11S 13A – 13 11S 13A – 13 11S 13A –
10 12 11S 12A – 12 11S 12A – 12 11S 12A –
11 11 11S 11A – 11 11S 11A – 11 11S 11A –
Number
1 25 11S 25A
2 23 11S 23B 25 11S 25B
3 21 11S 21D
5 18 11S 18B 19 11S 19C
6 17 11S 17C – 17 11S 17C –
7 16 11S 16A – 16 11S 16A –
8 15 11S 15A – 15 11S 15A –
9 14 11S 14A – 14 11S 14A –
10 13 11S 13B – 13 11S 13B –
11 12 11S 12B – 12 11S 12B –
Number of
teeth
Number of
teeth
3
4 5 6 7 8 9 10 11
11-23T 11-25T 11-28T
Mark Spider arm
11S 11-23
11S 11-23
12-25T 12-28T
Mark Spider arm
11S 12-25
11S 12-25
Number of
teeth
25 11S 25A
21 11S 21B
Number of
teeth
28 11S 28A
23 11S 23C
Mark Spider arm
Mark Spider arm
11S 11-25
11S 11-25
11S 12-28
11S 12-284 19 11S 19D 21 11S 21C
Number of
teeth
28 11S 28A
23 11S 23C
Mark Spider arm
11S 11-28
11S 11-284 18 11S 18A 19 11S 19B 21 11S 21C
4
Page 5
< CS-6800: 11T-23T, 11T-25T, 11T- 28T, 11T-32T, 12T-25T >
Sprocket spacers
Lock ring
1 2 3 4 5
Number
1 23 11S 23A
3 19 11S 19A 21 11S 21B 23 11S 23C
4 18 11S 18A
5 17 11S 17A 17 11S 17A 19 11S 19C
6 16 11S 16A – 16 11S 16A – 17 11S 17B –
7 15 11S 15A – 15 11S 15A – 15 11S 15A –
8 14 11S 14A – 14 11S 14A – 14 11S 14A –
9 13 11S 13A – 13 11S 13A – 13 11S 13A –
10 12 11S 12A – 12 11S 12A – 12 11S 12A –
11 11 11S 11A – 11 11S 11A – 11 11S 11A –
Number
1 32 11S 32A
3 25 11S 25C 21 11S 21B
4 22 11S 22A
5 20 11S 20A 18 11S 18B
6 18 11S 18C – 17 11S 17C –
7 16 11S 16B – 16 11S 16A –
8 14 11S 14A – 15 11S 15A –
9 13 11S 13A – 14 11S 14A –
10 12 11S 12A – 13 11S 13B –
11 11 11S 11A – 12 11S 12B –
Number of
teeth
Number of
teeth
Mark Spider arm
Mark Spider arm
6
11-23T 11-25T 11-28T
11S 11-23
11S 11-23
11-32T 12-25T
11S 11-32
11S 11-32
7 8 9 10 11
Number of
teeth
25 11S 25A
19 11S 19B
Number of
teeth
25 11S 25A
19 11S 19D
Mark Spider arm
11S 11-25
11S 11-25
Mark Spider arm
11S 12-252 28 11S 28B 23 11S 23B
11S 12-25
Number of
teeth
28 11S 28A
21 11S 21C
Mark Spider arm
11S 11-282 21 11S 21A 23 11S 23B 25 11S 25B
11S 11-28
5
Page 6
< CS-6800: 14T-28T >
Sprocket spacers
Lock ring
Number
1
2
3
4
5
6
7
8
9
10
11
1 2 3 4 5
14-28T
Number of
teeth
28 11S 28A
25 11S 25B
23 11S 23C
21 11S 21E
20 11S 20C
19 11S 19F 18 11S 18D 17 11S 17C 16 11S 16A 15 11S 15B 14 11S 14B -
Mark Spider arm
6
11S 14-28
11S 14-28
7 8 9 10 11
Note:
For junior teeth group adjustment, also check the adjustment section in the rear derailleur dealer's manual.
6
Page 7
< CS-5800: 11T-28T, 11T-32T, 12T-25T >
Tightening torque:
30 - 50 N·m
Sprocket spacers
Lock ring
1 2 3 4 7
Number
1 28 11S 28A
3 23 11S 23C 25 11S 25C 21 11S 21B
4 21 11S 21D – 22 11S 22B – 19 11S 19F –
5 19 11S 19E – 20 11S 20B – 18 11S 18D –
6 17 11S 17B – 18 11S 18C – 17 11S 17C –
7 15 11S 15A – 16 11S 16B – 16 11S 16A –
8 14 11S 14A – 14 11S 14A – 15 11S 15A –
9 13 11S 13A – 13 11S 13A – 14 11S 14A –
10 12 11S 12A – 12 11S 12A – 13 11S 13B –
11 11 11S 11A – 11 11S 11A – 12 11S 12B –
•
For installation of the HG sprockets, use the Shimano original tool TL-LR15 to tighten the lock ring.
•
To replace the HG sprockets, use the Shimano original tool TL-LR15 and TL-SR23 to remove the lock ring.
Number of
teeth
Mark Spider arm
5
11-28T 11-32T 12-25T
11S 11-28
6 8 9 10 11
Number of
teeth
32 11S 32A
Mark Spider arm
11S 11-32
Number of
teeth
25 11S 25A
Mark Spider arm
11S 12-252 25 11S 25B 28 11S 28B 23 11S 23B
Lock ring
7
Disassembly
TL-LR15
TL-SR23
Page 8
Please note: specifications are subject to change for improvement without notice. (English)
© Dec. 2016 by Shimano Inc. ITP
Loading...