Shimano BF-XY01 Service Instructions

SI-0129A-001-00

00

Language

0

0

207

207

207

General Safety Information

WARNING

If the laser beam gets into your eyes, it may cause blindness.

•Do not look at the laser beam directly.

•Do not let the laser beam get into your eyes while using the product, regardless of
whether the laser beam is seen directly or through mirrors.

•Do not control or adjust the product in any way other than by following the
procedures provided in this manual. It may cause you to be exposed to hazardous
laser beam emissions.

•This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Note:

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.

Service Instruction

SI-0129A-001

BF-XY01

Names of parts

Y-axis moving rail

Laser radiation section

Operation and indication screen

Reset button

Pressing the inside of the
frame resets the position
coordinate to 0.

Coordinate display

Shows the current coordinate.

0

0

207

207 179

207E179

Saving measurement value

Measurement values of the

179

X-axis and the Y-axis at each
position can be saved as the
measurement values for the
section selected by pressing.

Turning the laser ON / OFF

The laser turns on or off
with each press.

Turning off the screen display

Display information

Change settings

X-axis moving rail

Position Tool

XY Position Tool

A warning label and an
explanatory label

Certification label and
Identifi cation label

Basic usage

Inserting the batteries

Move the position tool to the uppermost section of the Y-axis moving rail. While pressing
in the marked section of the back cover, slide the back cover upwards to remove it. Insert
two AA batteries in the order shown in the fi gure then put the back cover back.

Two AA batteries

Turning on the screen display

Holding down any position on the position tool screen for one second or longer turns the
screen on.

Turning off the screen display

Turns the display of the position tool screen off.

Measurement

First, press [laser ON / OFF] on the

1.

position tool to turn on laser emissions.

OFF ON

Then, set the laser pointer at the

2.

reference point. Slide the rail to move
the position tool and set the pointer at
the cross at the center of the crank.

With the pointer placed over the

3.

intersection point of the cross, press
the X reset button and Y reset button
to set the reference point to zero.

Move the position tool to the

4.

measuring point and measure the
position. Press at any position you want
to save in order to save the
measurement value. Values of three
positions can be saved.

Reference point

Handle position

Saddle position

Other position

207 179

207 179

207

179

E

Displaying settings and information

Change settings

The change settings screen appears. Change the set values using [-] or [+] on the
left or right of each item. Holding down the button continuously switches the
display, and holding down the button longer switches the display quickly.

Language setting

1.

SETTINGS

Language

1.

English

Display brightness

2.

100 %

Power saver

3.

5 min

Power-off display

4.

10 min

Power-off sensors

5.

60 min

6.

Display information

Information such as the basic functions of the XY position tool and its usage
appears.

PMB-10 01-01 .02

The language can be selected from three
languages.
English ↔ German ↔ Dutch

Display brightness adjustment

2.

Adjust the brightness of the display.
Adjustment range: 0 % to 100 %

Power saver setting

3.

Set the time until laser emissions are turned
off.
Adjustment range: 1 min to 5 min

Power-off display setting

4.

Set the time until the screen display is turned
off when a stand-by state has continued for a
long time.
Adjustment range: 1 min to 10 min

Power-off setting

5.

Set the time until the system is powered off
when a stand-by state has continued for a
long time.
Adjustment range: 10 min to 60 min

Return to the previous screen.

6.

Laser specifi cations

Maximum power 1 mW

Wavelength 650 nm

Beam divergence 1.1 mrad

* Service Instructions in further languages are available at: http://si.shimano.com

One Holland, Irvine, California 92618, U.S.A. Phone: [phone]

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: [phone]

3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

Please note: Specifications are subject to change for improvement without notice. (English)
© Apr. 2014 by Shimano Inc. HTR