Shimano BF-XY00 Service Instructions

SI-0130A-000-00

General Safety Information

WARNING

If the laser beam gets into your eyes, it may cause blindness.

•Do not look at the laser beam directly.

•Do not let the laser beam get into your eyes while using the product, regardless of
whether the laser beam is seen directly or through mirrors.

•Do not control or adjust the product in any way other than by following the
procedures provided in this manual. It may cause you to be exposed to hazardous
laser beam emissions.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
_ Reorient or relocate the receiving antenna.
_ Increase the separation between the equipment and receiver.
_ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
_ Consult the dealer or an experienced radio/TV technician for help.

Service Instruction

SI-0130A-000

BF-XY00

Names of parts

A warning label and an
explanatory label

XY Position Tool

Position display

Power ON
button

X reset button
Y reset button

Laser ON / OFF
button

Power OFF button

Operation

Inserting the batteries

Push the two tabs located on the lower part of the position display inwards and then
remove the battery box. Insert four AA batteries in the order shown in the fi gure then
insert the battery box with the battery-mounting side down until you hear it click.

Four AA batteries

Tabs

Turning the power ON / OFF

Press the power ON button or power OFF button to turn the power ON / OFF.

Turning the laser ON / OFF

Laser emissions turn ON / OFF with each press of the laser ON / OFF button.

Measurement

Reference point

Set the reference point fi rst.

1.

Press the laser ON / OFF button on the position display to turn on laser emissions.
Set the laser pointer at the reference point. Slide the rail to move the laser radiation

2.

device and set the pointer at the cross at the center of the crank.
With the pointer placed over the intersection point of the cross, press the X reset

3.

button and Y reset button to set the reference point to zero.
Move the laser radiation device to the measurement point and read the X-axis and

4.

Y-axis values shown on the position display.

Calibration

You need to save an accurate scale value in this product to correctly measure the moving
distance. Perform calibration according to the following procedure before measurement.

Y-axis:
1000 mm

X-axis: 1000 mm

Setting the X-axis direction

Press the X reset button for 5 seconds.

1.

Move the laser radiation device. Accurately measure 1000 mm along the X-axis

2.

moving rail.
Press the power OFF button to turn off the power. The calibration of the X-axis

3.

direction is completed after the display turns off.

Setting the Y-axis direction

Press the Y reset button for 5 seconds.

1.

Move the laser radiation device. Accurately measure 1000 mm along the Y-axis

2.

moving rail.
Press the power OFF button to turn off the power. The calibration of the Y-axis

3.

direction is completed after the display turns off.

Laser specifi cations

Maximum power 1mW

Wavelength 650nm

Beam divergence 1mrad

Certification label and
Identifi cation label

Laser radiation section

Laser radiation device

Y-axis moving rail

X-axis moving rail

* Service Instructions in further languages are available at: http://si.shimano.com

One Holland, Irvine, California 92618, U.S.A. Phone: [phone]

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: [phone]

3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

Please note: Specifications are subject to change for improvement without notice. (English)
© Dec. 2013 by Shimano Inc. HTR