SHI KISB Electronic BTK28 User Manual

Stereo Bluetooth Headphone with Mic

(Model No: BTK-28)

User Manual

Charging the headphone

Your headphone uses a rechargeable battery. You must charge the battery fully before using the headphone for

the first time.

1. Plug the USB Cable into PC socket.

2. Connect the USB Cable with headphone as it shown on the picture. The red indicator of headset will turn on

when charging.

3. When the battery is fully charged, the red indicator will turn blue.

Note:

1) When the headphone is in low battery, the indicator will flash red and you will hear a voice “Battery Low”.

2) The headphone will be fully charged in approximately 3-4 hours.

3) Remove the USB cable from the PC socket

IMPORTANT: The headphone can be used while charging.

BASIC OPERATIONS Turning the headphone on/off

1. To turn the headphone on

Press and hold K1 Button for about 3 seconds, the indicator will flash blue for 1 second and you will hear a voice

“Power on”. The headphone is now turned on.

2. To turn the headphone off

Press and hold K1 Button for about 2 seconds, the indicator will flash red for 1 second and you will hear a voice

“Power off”. The headphone is now turned off.

Pairing

Before using your headphone for the first time, you must pair it with your Bluetooth devices.

1. Ensure that the headphone is turned off (see “To turn the headphone off” section). And the Bluetooth devices

setting are activated.

2. Press and hold K1 Button for about 5 seconds until the indicator light alternately flashes blue and red, and you

will hear a voice “Pairing”, now the headphone is under pairing mode.

3. Set your Bluetooth devices to discover the speaker by following your devices' guide. Typically, the steps involve

going to a ‘Setup’, 'Connect', or ‘Bluetooth’ menu on your devices and then selecting the option to discover

Bluetooth devices.

4. Your devices will find the headphone “iFlavor BTK-28” and ask if you want to pair with it. Confirm this by

pressing the “Yes” or “OK” key.

5. Enter a passkey or PIN code “0000” (4 zeros), then press the “Yes” or “OK” key.

Note: If the Bluetooth version of your Bluetooth devices is up Bluetooth V2.1, you do not need to enter a Passkey

(Pin code) during above pairing process.

6. You will hear a voice “connected”, it means your devices have been connected with the headphone.

IMPORTANT: If the pairing can’t be completed within 90 seconds while the pairing mode is activated, which means the pairing is unsuccessful, please repeat Step 1 to Step 6 to pair the speaker with the Bluetooth devices again.

Pairing Your Headphone with Two Bluetooth Devices (Multipoint connecting)

BTK-28 supports a Multipoint function to allow simultaneous pairing of the speaker with two Bluetooth

devices.

1. Follow the pairing procedure as instructed in “Pairing” section to pair the headphone with the first Bluetooth

device.

2. Repeat the same pairing procedure on the second Bluetooth device.

3. On the first Bluetooth device’s menu, activate its Bluetooth connection with the headphone.

Play/Pause

1. Make sure that your devices connected with the headphone.

2. Find music in your devices and play, the song will play through the headphone.

3. Press K1 Button once when play, the song will stop. Press K1 Button again, the song will play again.

Previous Song

Press “PREV” Button to back to the previous song.

Next Song

Press “NEXT” Button to the next song.

Adjusting the volume

1. Press “VOL-” to decrease the volume and you will hear a beep when it is minimum

2. Press “VOL+” to increase the volume and you will hear a beep when it is maximum.

Making a call

1. Dial number on the keypad or select the contact name from the contact list of your mobile phone.

2. Press phone’s “send/call” key.

+ 2 hidden pages