ShenZhen ART TECH R C Hobby ETC62D User Manual
ETC62D-2.4GHz
LCD DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM
Operating Manual
Catalog
Function of Transmitter 0 3
Contents 04
Specifications 04
Notice for use 04
Notification before Using 05
Transmitter particular introductine 06
Menu introduction 07
Other function of the transmitter 11
Receiver 12
Electronic speed controler 10
Operation for transmitter and servo 13
The process of frequency bind for 2.4GHz R/C system 15
Adjust order 14
Charge method of battery 16
Flow list 17
02
www.art-tech.com
Thanks for purchasing ETC62D-2.4GHz radio control set. For safe use, please read
this manual before using carefully. Any damage or loss to radio control set and model
due to inproper use will not be shouldered by Art-Tech.
Function of Transmitter
ETC62D-2.4GHz is a newly developed 6 channel proportional transmitter. The latest developed
product of ART-TECH RC Hobby Corporation. The 2.4GHz RC system uses digital frequency-hopping
technology; it has enormous advantage compared with traditional system: no crystal, no frequency
interference, short antenna length and low power consumption.
1. Flying time display: less than 1 minute seconds showed, more than 1 minute minutes showed.
2. Supply voltage display and low voltage alarm function: When the battery voltage is lower than 8.5V,
the red LED flashes, and alarm.
3. Channel output reverse set.
4. 5 kinds of aircraft modes to choose， 12 independent aircraft data storage and call.
5. Mode I and mode II exchange.
6. Throttle protection: in order to avoid danger of starting the motor of a
sudden, when throttle hold switch is turned on, throttle output value is the
minimum.
When boot, for various reasons (location of the assembly, curve setup),
throttle output value is not the minimum, the red LED flashes and alarm, as
shown in the figure. The throttle lose automatically locked out for a
minimum value, when the transmitter adjustment is appropriate (that is, the
throttle output is the smallest), the transmitter is unlocked.
7. Ch1 ch2 ch4 DR (Dual Rate) setting.
8. Ch1 ch2 ch4 EXP(exponential curve) setting.
9. All channel EPA (end of the process) setting.
10. Ch5 two-state setting (gyroscope sensitivity setting for helicopters, landing gear set up for fixed-
wing planes).
11. Ch3 ch6 general and 3D mode curve set for general helicopters and CCPM helicopters
12. 4 groups channel mixing control
13. All channel output dynamic display
14. All channel mid-point regulation
15. Restore the factory settings
16. Ch1 ~ Ch6 auxiliary fine-tuning settings
www.art-tech.com
03
Contents:
Transmitter:
Receiver: ER62-2.4GHz 1p c s
Simulator cable: 1pcs
We do not offer servo, speed controller, battery or changer with the radio control system .
Users can buy as spare parts.
Servo: AS-100(9 g) 3pcs
Speed controller:
ETC62D-2.4GHz
ESC-30A
1pcs
1pcs
Belt: 1pcs
Manual: 1pcs
CD: 1pcs
Bettery packs:
Charger:
9.6V/Ni-MH
Specifications
Number of channels: 6
Charging jack: yes
3D switch: yes
Power supply: 12 V (1.5V * 8AA batteries)
Voltage Display: LCD
Color: Black
Antenna length: 15 cm
Using occasions: aircraft, helicopters
Certification: FCC, CE, RoHS
Notice for use
Please do not fly in the rain or strong wind. The
water can sink into the transmitter which can
cause out of control,leading to crash.
1pcs
1pcs
The transmitter can not work properly if the
frequency bind button is pressed down
neglectfully. In this case, The transmitter and
the receiver must be bind again. More details ,
Please refer to the process of frequency bind for
2.4 GH z R/C system.
Please do not turn on several RC devices and
bind them at the same time, bind only one set of
RC device at one time.
The RC device should
not be stay in bind state for a long time.
Pleas note before using, test the radio set first
and any change to the radio set or model can
cause crash.
Please do not fly near housing, road,airport or
power line
04
www.art-tech.com
Notification before Using
Indications of Special signs
Please pay more attention to signs in this manual and safety while using
Show
WARNING
CAUTION
Logo
Meanings
I improper operation may cause injury or hurt
I improper operation may cause injury or hurt
Storage note
▲Please do not place the radio control set in the below situation:
hot or cold（60℃above or -10℃below）
under the sunshine long time
moist condition
dusty place
vibration condition
▲long time without using, please pick up batteries from the bay and store in the dry condition.
▲It is forbidden to clean the radio control set with chemical solvent such as acetone
▲The over used dry batteries can not be dispatched anywhere. That should be stored in a non-metal
tool and dispatched by environment-protection department.
▲ It is strongly recommended to use chargeable battery for the transmitter with the hope of
environment-protection and cost-reducing.
Attention
While opening the transmitter,the joystick for throttle shoule be on idle;only opening the transmiiter
can c onnec t t he powe r to mode l.
In order to close the transmitter, the joystick for throttle should be o nidle . Disconnect t h e power of
mod el,an d c lose th e trans mitter . The pro pelle r mayc ause d amageif im proper operation.
Stop the motor while transmitter adjustment. Please pay attention to the motor during adjustment.It is
better to use transmitter ,receiver etc,together from ART-TECH.
Ple ase do not do any chan g e t o t r ansmi tter, oth erwis e i t ca n a ffect transmitter`s function.
www.art-tech.com
05
Transmitter particular introduce
A
B
C
D
E
F
G
H
I
K
M
O
Q
R
LCD DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM
MENU
SUB
ETC62-2.4GHz
Y/UP
RIGHT
LEFT
N/DOWN
J
L
N
P
S
T
U
V
A：Antenna
B：LCD(Liquid Crystal Display)
1）display battery voltage of transmitter
2）display whether the channels are reversed
3）display fly in g time
4）display menus
5) Display lock or unlock state
Di spl ay ar ea
1) fu nc tion display ar ea
2) channels direction display area
3) da ta d isplay area
4) op ti on number displ ay a rea
C：Th ro tt le h old switch
D：Ch 5 sw it ch
Th is s witch is for Ch 5 th at c an be used fo r ae ri al
camera, collapsible landing gear and shift
between gyr o mo de and gyro g ai n, e tc.
E：3D switch
F：D/R sw it ch
G：Indicator LED for Power voltage
H：Re d In di cator LED for l ow v ol tage alarm: When
battery voltage is under 8.5V, the LED wi ll f la sh and
alarm; th e LC D will cut off when v ol ta ge is under 7.6 V。
No te : When red LED fl as he s or nothing sh ow s on
LC D,
please change the battery in order to avoid
flying out of control.
I：Joystick
1）If the transmitter is Mode 1,CH1 is for aileron
an d CH 3 for throttl e.
2）If t he t ransmitter is M od el 2 ,CH1 is for a il er on
and CH2 for Rudder
J：Joystick
1）If t he t ransmitter is M od el 1 ,CH2 is for e le va to r
and CH4 for rudder.
2）If t he t ransmitter is M od el 2 ,CH3 is for t hr ot tl e and
CH 4 fo r rudder.
W
X
A1
Y
Z
K：Throttle trim lever (Mode 1)
Elevator trim lever (Mode 2)
1）If the transmitter is Mode 1,it is for Ch3
2）If the transmitter is Mode 2,it is for Ch1
L：Elevator trim lever (Mode 1)
Throttle trim lever (Mode 2)
1）If the transmitter is Mode 1,it is for Ch1
2）If the transmitter is Mode 2,it is for Ch3
M：Rudder trim lever
N：Aileron trim lever
O：Switch for Power
P：Flying Ring
Q：Menu Button
1) Enter into main menu
2) Enter into next main menu
3) Enter into time page menu (release after long
press)
R：Sub Button
1) Enter into sub menu
2) Enter into next sub menu
3) Enter into time page menu (release after long
press)
S：Y/UP
1) Selection validate
2) Data increase
3) Normal channel direction selects (release after
long press)
T：RIGHT Button, selection(right)
U：N /DOWN
1) Selection cancels
2) Data decrease
3) Reverse channel direction select (release after
long press)
V：LEFT Button, selection(left)
W：Steel Handle
X：Bind Button
Y：Plug for Simulator
Z：Battery bay for transmitter
A1：Rechargeable plug ( Note: Only 9.6V Ni-MH
battery pack can be recharged )
06
www.art-tech.com
Loading...