ShenZhen Aoni Electronic Industry E96F User Manual

Quick Start Guide

Smart Wireless Cube Camera

Model: E96F

FCC ID: Z63-E96F

Welcome

Thank you for choosing our smart camera. Getting started is easy.

1. What’s Included

Quick Start Guide

Smart Wireless Cube Camera

3M tape

Model: E96F

Security Camera

Power Adapter

Reset Needle

Quick Start Guide

2. Product Details

Lens

Infrared lights

Indicator light

Microphone

Base

MicroSD card

Reset

Speaker

Power interface

3. Connection Preparation

Bring the camera and phone within 1 to 3 feet (30 to

100 centimeters) of the router.

Router

Smartphone

30cm~100cm

Camera

Note: Make sure smart phone is connected with your wireless router.

Please note the camera is only working under 2.4G Wi-Fi, not support 5G Wi-Fi.

4. Get the APP and Account

For the best experience, please download the "Tuya

Smart" APP to your smartphone from App Store or

Google Play, or you can also scan the QR code below,

the APP icon will be displayed after installed successfully.

Tuya Smart

Launch the app from your smartphone and click the

5. Insert the Micro SD card

Insert the Micro SD card gently on the side edge

of camera.

6. Connect the power to the camera

Connect the power to the camera by DC5V/1A Micro USB

Power Adapter.

7. Set up your camera

Use the Reset Needle to press the reset button of

camera above 5 seconds, then release the button,

a red LED on the front of camera will blink quickly.

ollow App's instructions to complete network

pairing process, the device will connect to your

Wi-Fi network successfully.

The blue light is on, camera is ready for viewing.

Rtguu"vjg"Tgugv"dwvvqp" hqt"cdqxg"7"ugeqpfu"vq" uvctv"Tgugv"rtqeguukpi

8. Place or Mount Your Camera

You can place your camera on a shelf or other flat surface, or you can mount it to the wall.

Tgf"nkijv"

To mount your camera to the wall:

dnkpmu

You can use 3M sticker to mount the camera on the wall.

3M tape

You’re done!

Congratulations! Your camera is set up and ready to go.

Appendix: Camera LED Guide

NO. LED Status Camera Status

1 System starting upRed LED on

2 Standby for configurationRed LED blinks quickly

3 Network pairingBlue LED blinks quickly

4 Camera onlineBlue LED on

All trademarks are used for reference purposes only.

Thanks again for choosing our smart camera! Make

life safe in your hands!

Boost security mobility in your smartphone!

OTA upgrade Red LED blinks slowly

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

*RF warning for Mobile device:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.