ShenZhen X1 Users manual

尺⼨：108*72mm

Wirel ess Charg er Stan d

Enviro nme nta lly f rie ndl y dis pos al

Old e lectr ical ap plian ces mus t not be di spose d of toge ther wit h the res idual w aste, b ut have t o be disp osed of s epara tely. The d ispos al at the c ommun al coll ectin g point v ia priv ate per sons is f or free . The own er of old a pplia nces is r espon sible to br ing the a pplia nces to t hese co llect ing poi nts or to s imila r col lecti on poin ts. Wit h this li ttle pe rsona l effor t, you co ntrib ute to re cycle v aluab le raw ma teria ls and th e treat ment of t oxic sub stanc es.

FCC I D: 2A OSU X1

FCC STATEMENT:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a WPC device, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.

NOTE: This equipment has been tested and found to comply with the limits for a wireless power charger, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

User Manu al

Thanks Fo r Choosing Us !

In order to br ing you a bett er ex perie nce, read th is manua l and also ple ase refer to your m obile p hone or your el ect ronic prod uct m anual .

Product Introduction

Wireless c harger X1 is a n intellig ent sim ple desig n pro duct, c omp atible wit h all Qi- enabled ce ll phone s and device s. You d on't need any c ord s to plug in a nd out any mor e. Ju st plac ing your dev ice in the cen ter o f X1, y ou are free to enjo yyourwirel ess andlim itlesscha rgi ngexpe riencenow !

Bui lt-in 2 Co ils

Anti-slippery

Power Input

Rubber band

LEDindicator area

Use Instruction

1.Plea se use good br and 2A ad apt er orQC2 .0/ QC3.0 fast ch arg ing ada pte r(9V,1. 67A).

2.Connecting power with USB port, the indicator will flash for 3 seconds when power is on.

LEDindicator flash 3s

cha rging l ine (Mi cro USB )

3.① Locate your phone on charging pad and make sure it at sweet spot for effective charging.

LEDindicator flash 15s

②When th e phone is cha rge d succe ssfully, th e LED ind icator wil l flash for 15 s econd s the n off to ke ep the whole c harging pr oce ss sleep -friendl y.

Product Specification

Model : X1 Size: 9 0.3mm*11 0mm Input :5V 2A,9V 1.67 A Outpu t: 5W/7.5W /10 W Charging D istan ce: 4 mm-6m m Coils : 2 coils Net Weight : 118 g

PackageContents

Wir eless C harge r Stand

x1 x1 x1

cha rging l ine

Ins truct ion boo k

Attention

1. Keep the charger away from water and other liquid is required.

2. Please make sure the power is cut off before you start to clean the charger.

3. Use the charger under temperature only between 0-45°C.

4. Do n ot drop t he prod uct or s ubmit i t to impa ct.

5. Dr oppin g the pro duct o r submi tting i t to impa ct can c ause th e produ ct to ma lfunc tion.

6. Do n ot plac e the pro duct in a n area ex pose d to heal , direct s unlig ht, dam pness , moist ure, ra in, vib ratio n, shoc k , dust or s and.

7. Do n ot plac e the pro duct ne ar any ki nd of magn et or exp ose it to exc essiv e vibra tion.