
F-3098 use manual
Module Description:
1 Significantly enhance the overall the latest CSR BC6 chip, sound quality and RF performance.
2 Accord Bluetooth V3.0
3 Bluetooth headsets, audio, car low cost solution.
4 High-quality audio processing A2DP V1.2.
5 The highest the 2db emission power, -91db accept sensitivity.
6 module size: L23.5*W15.5*H1.8mm.
Application:
1 High sound quality Bluetooth headset.
2 Hands free, Bluetooth Car
3 High-quality Bluetooth audio
Pin Configurations:
Item Name Type Function
1 GND2 GND Ground connections
2 AIO1 Bidirectional Programmable input/output line
3 AIO0 Bidirectional Programmable input/output line
4 PIO20/RX Bidirectional with weak
internal pull-down
5 PIO23 Bidirectional with weak
internal pull-up
6 PIO3 Bidirectional with Programmable input/output line PIO[3] is
UART data input, active high. PIO[20] is
clock for SPI flash interface
UART data output, active high. PIO[23]
is data output for SPI flash interface

programmable strength
internal pull-up/down
7 PIO2 Bidirectional with
programmable strength
internal pull-up/down
8 PIO1 Bidirectional with
programmable strength
internal pull-up/down
9 PIO0 Bidirectional with
programmable strength
internal pull-up/down
10 RST Input with weak internal
pull-up
11 PIO11 Bidirectional with
programmable strength
internal pull-up/down
12 LED1 Open drain output LED driver
13 LED0 Open drain output LED driver
14 GND3 GND Ground connections
15 GND GND Ground connections
16 1V8 Power Positive supply for blue core
17 POWER_EN / Take high to enable both high-voltage
18 BAT / Lithium ion/polymer battery positive
19 CHG / Lithium ion/polymer battery charger
20 MIC_BIAS Analogue Microphone bias
21 MIC_P Analogue Microphone input, positive
22 MIC_N Analogue Microphone input, negative
23 SPKP_N Analogue Speaker output, negative
24 SPKP_P Analogue Speaker output, positive
25 MOSI with weak internal
pull-down
26 CLK Bidirectional with weak
internal pull-down
27 CSB Bidirectional with weak
internal pull-down
28 MIS0 Bidirectional with weak
internal pull-down
29 GND1 GND Ground connections
30 RF RF RF
chip select for SPI flash interface
Programmable input/output line
Programmable input/output line
Programmable input/output line
Reset if low. Input debounced so must be
low for >5ms to cause a reset
Programmable input/output line. PIO[11]
is data input for SPI flash interface
regulator and switch-mode regulator
teminal. Battery charger output and input
to switch-mode regulator
input
SPI data input
SPI clock
Chip select for SPI, active low
SPI data output

31 GND0 GND GND
Restrictions: Integration limited to Battery-operated host devices.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC ID: KKI-F-3098
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment。
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.

Important compliance information for North American users
The F-3098 Module has been granted modular approval for portable applications. Integrators may
use the F-3098 Module in their final products without additional FCC certification if they meet the
following conditions. Otherwise, additional FCC approvals must be obtained.
1. To comply with FCC regulations limiting both maximum RF output power and human exposure
to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure
condition must not exceed 0dBi in the 2.4G band.
2. The F-3098 Module and its antenna must not be co-located or operating in conjunction with any
other transmitter or antenna within a host device.
3. A label must be affixed to the outside of the end product into which the F-3098 Module is
incorporated, with a statement similar to the following: For F-3098: This device contains FCC
ID: KKI-F-3098.
4. A user m anual with the end product must clearly indicate the operating requirements and
conditions that must be observed to ensure compliance with current FCC RF exposure
guidelines.
The end product with an embedded -F-3098 Module may also need to pass the FCC Part 15
unintentional emission testing requirements and be properly authorized per FCC Part 15.