ShelterLogic 71534 User Manual
12'W x 8'H Peak Style Frame Assembly
Please read and understand instructions
completely before assembly.
Layout out frame parts as shown and match up items with quantity to make
sure no parts are missing.
Middle Ribs
End Rib
Top Rail
End Rib
Side Rails
Assembly
Reference #
1
2
3
4
5
6
7
8
9
10
11
Wind Brace
Mfg.
Part #
10131
10121
10132
10125
10126
10127
10128
10133
2030
10134
2031
Assembly
Reference #
12
13
14
15
16
17
18
19
20
21
Wind Brace
Mfg.
Part #
10135
10110
10111
10112
669
10210
10114
10115
10113
800260
Page 2
Cover Rails
ATTENTION:
FOR MISSING OR
REPLACEMENT PARTS
OR QUESTIONS,
PLEASE CONTACT
CUSTOMER SERVICE:
1.800.524.9970
CANADA 1.800.559.6175
www.shelterlogic.com
150 Callender Road
Watertown, CT 06795
05-101113-0C 09/04/07
Basic Frame Assembly
NOTE: FRAME EXTENSION KIT
12'x20'x8' is the base frame dimension. Your model may have more middle ribs than shown in the illustration on pg.2. You will
receive one extra rib for every extra 4 ft. of building length that you purchase. The basic frame assembly will remain the same. The
cover will be the correct size for the length of the building. Part #10223 is not required if your building is only 8' tall.
STEP 1: PLOTTING THE FRAME
Fig. 1
Before building your shelter, you should choose a flat area on your property and plot
your shelter.
1. Stake out the area for the shelter in the desired spot. The width of the area
should be at least equal to the width of the shelter and the length should be
equal to the length (“L”) of the shelter Fig. 1.
2. To be sure the staked area is square tie a rope diagonally from corner to corner.
3. Measure from where the two ropes intersect each other to all 4 corners. This
measurement should be the same. If they are not equal the stakes need to be
adjusted until the width, length and inside measurements are correct.
STEP 2: ASSEMBLE END RIBS
Fig. 2
Assemble end ribs as shown in Fig. 2. Securely
fasten all of the joints with the hardware indicated.
10132
10127
10128
12'
12'
Fig.1
10121
10125 10125
2" Bolts
End Rib
Length of
Building
10132
10127
10128
STEP 3: ASSEMBLE MIDDLE RIBS
Fig. 3
Assemble all of the middle ribs as shown in Fig. 3. Securely fasten
all of the joints with the hardware indicated.
Page 3
10132
10126
Fig.2
10131
10125 10125
2" Bolts
Middle Rib
Fig.3
10132
10126
STEP 4: INSTALL SIDE RAILS AND
SHELTERLOCK™ STABILIZER BLOCKS
Fig. 4
With help move the first end rib into the desired staked area. Place
the ShelterLock on the upright as shown in Fig. 4. From the outside
of the rib insert the bolt through the upright and then through the
ShelterLock. Place the plain end of the side rail over the bolt and
nest it into the ShelterLock. Install the nut onto the bolt and tighten.
Repeat these steps for the opposite side and all of the remaining ribs.
The side rails for the last rib will have two plain ends.
10210
2030
2030
800260
Fig. 2
1010
Fig. 4
STEP 5: INSTALL WIND BRACES
2030
Fig. 5
Take the wind brace and attach it between the end rib and the
first middle rib as shown in Fig. 5. Any attachments at the
cross rails should be made on the very inside of the cross rail.
10135
STEP 6: INSTALL TOP RAIL
Fig. 6
Place the first top rail over the pipe on the top end connector Fig. 6. The same cross
rail should lay on top of the first middle rib as with all of the middle ribs. Secure the
rails to the frame with the hardware indicated in Fig 6. The top rail attached to the
last rib will be installed over the pipe on the top end connector.
2030
Wind Brace
10135
Fig. 5
Install the Top Rail
Over all Middle Ribs
669
Page 4
Fig. 6
Loading...