Page 1
10' x 20'
MaxAP
™
Canopy
Assembly Instructions
DESCRIPTION MODEL #
™
MaxAP
Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.
THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE.
Before you start: 2 or more individuals recommended for assembly, approximate time 2 hour.
10' x 20' Canopy - 8 Leg - Sandstone
RECOMMENDED TOOLS
29522
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com
1/19/12
1-800-524-9970
Canada:
1-800-559-6175
05_29522_0BPage 1
Page 2
ATTENTION:
This shelter product is manufactured with quality materials. It is designed to t the ShelterLogic
ShelterLogic
Please anchor this ShelterLogic
®
Corp. Shelters offer storage and protection from damage caused by sun, light rain, tree sap and animal - bird excrement.
®
Corp. structure properly. See manual for more anchoring details. Proper anchoring, keeping cover
tight and free of snow and debris is the responsibility of the consumer. This product is not recommended for severe weather conditions.
Please read and understand the installation detail, warnings and cautions prior to beginning installation. If you have any questions call
the customer service number listed below. Please refer to the warranty card inside this package.
®
Corp. custom fabric cover included.
DANGER:
Prior to installation, consult with all local municipal codes regarding installation of temporary shelters.
Choose the location of your shelter carefully. DANGER: Keep away from electrical wires. Check for
overhead utility lines, tree branches or other structures. Check for underground pipes or wires before
you dig. DO NOT install near roof lines or other structures that could shed debris onto your shelter.
DO NOT hang objects from the roof or support cables.
WARNING:
Risk of re. DO NOT smoke or use open ame devices (including grills, re pits, deep fryers, smokers or
lanterns) in or around the shelter. DO NOT store ammable liquids (gasoline, kerosene, propane, etc.) in
or around your shelter. Do not expose top or sides of the shelter to open re or other ame source.
CAUTION:
Use CAUTION when erecting the frame. Use safety goggles during installation. Secure and bolt together
overhead poles during assembly. Beware of pole ends.
PROPER ANCHORING AND INSTALLATION OF FRAME:
PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER.
ShelterLogic
securely has the potential to y away causing damage, and is not covered under the warranty. Periodically check the anchors to ensure
stability. ShelterLogic
removed and stored prior to severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend
removal of cover.
®
Corp.
is not responsible for damage to the unit or the contents from acts of nature. Any product that is not anchored
®
Corp. cannot be responsible for any product that blows away. NOTE: Your product’s cover can be quickly
REPLACEMENT PARTS, ASSEMBLY, SPECIAL ORDERS:
Genuine ShelterLogic
application, replacement covers, wall and enclosure kits, frame parts, zippered doors and other accessories. All items are shipped
factory direct to your door.
U.S. CUSTOMER SERVICE: 1-800-524-9970 INTERNATIONAL CUSTOMER SERVICE: 001-860-945-6442 CANADA CUSTOMER SERVICE: 1-800-559-6175
®
Corp. replacement parts and accessories are available from the factory, including anchoring kits for nearly any
QUESTIONS - CLAIMS - SPECIAL ORDERS? CALL OUR CUSTOMER SERVICE HOTLINE:
HOURS OF OPERATION: MON-FRI 8:30AM-8:00PM EST, SAT-SUN 8:30AM-5:00PM EST.
CARE AND CLEANING:
A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can accelerate
deterioration of cover fabric. Immediately remove any accumulated debris from the roof structure with a
broom, mop or other soft-sided instrument. Use extreme caution when removing debris from cover- always
remove from outside the structure. DO NOT use hard-edged tools or instruments like rakes or shovels to
remove debris. This could result in punctures to the cover. DO NOT use bleach or harsh abrasive products to
clean the fabric cover. Cover is easily cleaned with mild soap and water.
WARRANTY:
This product carries a full limited warranty against defects in workmanship. ShelterLogic
if properly used and installed, the product and all associated parts, are free from manufacturer’s defects for a period of:
1 YEAR FOR COvER FABRIC, END PANELS AND FRAMEWORk
Warranty period is determined by date of shipment from ShelterLogic® Corp. for factory direct purchases or date of purchase from an authorized
reseller, (please save a copy of your purchase receipt). If this product or any associated parts are found to be defective or missing at the time of receipt,
ShelterLogic
parts shall be covered for the remainder of the Original Limited Warranty Period. All shipping costs will be the responsibility of the customer. Parts and
replacements will be sent C.O.D. You must save the original packaging materials for shipment back. If you purchased from a local dealer, all claims
must have a copy of original receipt. After purchase, please ll out and return warranty card for product registration. Please see warranty card for more
details.
®
Corp. will repair or replace, at it’s option, the defective parts at no charge to the original purchaser. Replacement parts or repaired
®
Corp. warrants to the Original Purchaser that
Covered by U.S. Patents and patents pending: 6,871,614; 6,994,099; 7,296,584; D 430,306; D 415,571; D 414,564; D 409,310; D 415,572
120211
05_29522_0BPage 2
Page 3
MaxAP™ 10' x 20' Canopy - Parts List - Model #29522
Description of Parts:
Rafter Poles 24
Cross Rails 40
Cross Rails 39
3
in. / 61,9 cm
/
8
11
in. / 103,3 cm
/
16
1
in. / 100,3 cm
/
2
Leg Poles 39 in. / 99 cm
3 - Way Frame Connectors
4 - Way Frame Connectors
Bungee Cords
Cover
Base Feet
Temporary Spike Anchors
Quantity Part #
8
25
9
8
6
6
24
1
8
8
802204
802203
802207
802205
802201
802202
10066
803072
802916
10431
1. LAY OUT ROOF FRAME
802201
802207 802207 802207
802204 802204 802204
802203 802203 802203
802201
802207 802207 802207
802203 802203 802203
802203 802203 802203
FRONT
802203 802203 802203
802204 802204 802204
802202 802201
802202 802201
802202
802204
802203
802202
802203
802204
REAR
802201
802207 802207 802207
802203 802203 802203
802202 802201
802202
05_29522_0BPage 3
Page 4
2. ASSEMBLE ROOF FRAME
NOTE: Swedged tubes insert into plain ends at the crimp marks.
3. ASSEMBLE LEGS & ATTACH TO ROOF FRAME
A. Attach all legs to one side rst. Let the other side of roof frame rest on the
ground. Repeat for opposite side.
Swedged Tubes Connections
802203
Crimp Marks
802204
Leg Pole Assembly
802205
802203
802916
4. ANCHOR THE FRAME
There are four holes on each base foot that the anchor can go into.
A. Select a hole in each base foot. Insert each anchor (10431) into the ground until the round head is touching the
base foot. These anchors prevent the canopy from shifting. Insert one anchor into all four base feet.
This is a temporary spike anchor. Not intended for permanent use.
B. To securely anchor canopy, Accessory Anchoring Kit #10073 is recommended. The 4-anchor pins are inserted
into the ground. Then the ropes are tied from the anchors to the corner tees as shown in B.
Anchoring Base Feet
A
10431
802203
Tie Rope Around Frame Corners
802204
802201
B
802916
802205
rope
05_29522_0BPage 4
Page 5
5. PLACE COVER AND SECURE TO CANOPY FRAME
A. Place cover over assembled roof frame with grommet panels facing down, aligned with cross rails.
B. Make sure the cover is properly aligned on the frame, secure the four corners of the cover with bungees
(10066) to the frame rst. Attach remaining bungees.
Re-adjust bungees position along cross pole as needed to ensure a tight and even t of the cover to the frame.
Grommet Panels for Bungees
Grommet Panel
Cover
Grommet Panels for Bungees
Grommet
Panel
10066
Cover
6. TIGHTEN THE COVER WITH TWIST TITE
Insert Bungee Cord Through Grommet Hole
™
A. Wrap the cord with plastic ball and "S" hook at the corners of the cover
around the corner leg poles. Insert "S" hook into the hole of the corner
leg poles.
B. Twist each leg pole toward the inside of the shelter until the cover
becomes tight. Twist the leg poles equally to ensure the cover stays
aligned during tightening.
Secure Bungee Around Plastic Ball
Twist-Tite™ Tighten Cover
Cover
802201
802205
05_29522_0BPage 5
Loading...