18' x 30'
SUPER MAXTM ENCLOSURE KT
Assembly Instructions
Frame Not Included
DESCRIPTION MODEL #
TM
18' x 30' Super Max
Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.
THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE.
Before you start: 1+ individual recommended for assembly, approximate time 2 hr.
- 12 Leg - Enclosure Kit - White
RECOMMENDED TOOLS
26779
!
WARNING!
KEEP ALL FLAME AND HEAT SOURCES
AWAY FROM THIS TENT FABRIC
This tent meets the ammability requirements of
CPAI-84. The fabric may burn if left incontinuous
contact with any ame source. The application
of any foreign substance to the tent fabric may
render the ame-resistant properties ineffective.
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com
5/5/10
1-800-524-9970
Canada:
1-800-559-6175
Page 1 05-26779-0C
ATTENTION:
This shelter product is manufactured with quality materials. It is designed to t the ShelterLogic
ShelterLogic
Please anchor this ShelterLogic
®
, LLC Shelters offer storage and protection from damage caused by sun, light rain, tree sap and animal - bird excrement.
®
, LLC structure properly. See manual for more anchoring details. Proper anchoring, keeping cover
tight and free of snow and debris is the responsibility of the consumer. This shelter is not recommended for severe weather conditions.
Please read and understand the installation detail, warnings and cautions prior to beginning installation. If you have any questions call
the customer service number listed below. Please refer to the warranty card inside this package.
®
, LLC custom fabric cover included.
DANGER:
Prior to installation, consult with all local municipal codes regarding installation of temporary shelters.
Choose the location of your shelter carefully. DANGER: Keep away from electrical wires. Check for
overhead utility lines, tree branches or other structures. Check for underground pipes or wires before
you dig. DO NOT install near roof lines or other structures that could shed debris onto your shelter.
DO NOT hang objects from the roof or support cables.
WARNING:
Risk of re. DO NOT smoke or use open ame devices (including grills, re pits, deep fryers, smokers or
lanterns) in or around the shelter. DO NOT store ammable liquids (gasoline, kerosene, propane, etc.) in
or around your shelter. Do not expose top or sides of the shelter to open re or other ame source.
CAUTION:
Use CAUTION when erecting the frame. Use safety goggles during installation. Secure and bolt together
overhead poles during assembly. Beware of pole ends.
PROPER ANCHORING AND INSTALLATION OF FRAME:
PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER.
ShelterLogic
securely has the potential to y away causing damage, and is not covered under the warranty. Periodically check the anchors to ensure
stability of shelter. ShelterLogic
quickly removed and stored prior to severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend removal of cover.
®
, LLC
is not responsible for damage to the unit or the contents from acts of nature. Any shelter that is not anchored
®
, LLC cannot be responsible for any shelter that blows away. NOTE: Your shelter’s cover can be
REPLACEMENT PARTS, ASSEMBLY, SPECIAL ORDERS:
Genuine ShelterLogic
application, replacement covers, wall and enclosure kits, vent and light kits, frame parts, zippered doors and other accessories. All
items are shipped factory direct to your door.
QUESTIONS - CLAIMS - SPECIAL ORDERS? CALL OUR CUSTOMER SERVICE HOTLINE:
U.S. CUSTOMER SERVICE: 1-800-524-9970 INTERNATIONAL CUSTOMER SERVICE: 001-860-945-6442 CANADA CUSTOMER SERVICE: 1-800-559-6175
HOURS OF OPERATION: MON-FRI 8:30AM-8:00PM EST, SAT-SUN 8:30AM-5:00PM EST.
®
, LLC replacement parts and accessories are available from the factory, including anchoring kits for nearly any
CARE AND CLEANING:
A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can accelerate deterioration of cover fabric. Immediately remove any accumulated debris from the roof structure with a
broom, mop or other soft-sided instrument. Use extreme caution when removing debris from cover- always
remove from outside the structure. DO NOT use hard-edged tools or instruments like rakes or shovels to
remove debris. This could result in punctures to the cover. DO NOT use bleach or harsh abrasive products to
clean the fabric cover. Cover is easily cleaned with mild soap and water.
WARRANTY:
This shelter carries a full limited warranty against defects in workmanship. ShelterLogic
properly used and installed, the product and all associated parts, are free from manufacturer’s defects for a period of:
1 YEAR FOR COvER FABRIC, END PANELS AND FRAMEWORK
Warranty period is determined by date of shipment from ShelterLogic®, LLC for factory direct purchases or date of purchase from an authorized
reseller, (please save a copy of your purchase receipt). If this product or any associated parts are found to be defective or missing at the time of receipt,
ShelterLogic
shall be covered for the remainder of the Original Limited Warranty Period. All shipping costs will be the responsibility of the customer. Parts and replacements will be sent C.O.D. You must save the original packaging materials for shipment back. If you purchased from a local dealer, all claims must have a
copy of original receipt. After purchase, please ll out and return warranty card for product registration. Please see warranty card for more details.
®
, LLC will repair or replace, at it’s option, the defective parts at no charge to the original purchaser. Replacement parts or repaired parts
®
, LLC warrants to the Original Purchaser that if
Covered by U.S. Patents and patents pending: 6,871,614; 6,994,099; 7,296,584; D 430,306; D 415,571; D 414,564; D 409,310; D 415,572
05-26779-0CPage 2
18' x 30' 2" SUPER MAX - 12 Leg - Enclosure Kit Parts List - Model #26779
Description of Parts:
Side Walls
Back Panel
3 - Zipper Door
Bungee Cords
Quantity Part #
2
1
1
102 10066
10334
10336
10337
NOTES:
• Canopy Enclosure panels attach to frame with bungee cords.
• Leave Canopy Cover bungees in place when attaching Enclosure panels.
CAUTION: Bungee Cords are under extreme tension. Use Caution when installing. Safety glasses are
recommended to prevent injury.
1. ATTACH SIDE WALLS TO FRAME
A. If tightened at corner leg poles, disengage the TwistTite™ cord and “S” hook from canopy cover and corner
legs. Re-tighten after all Enclosure panels have been secured, as shown in Step 3.
B. Attach the extension panels with bungees to the cross rails at the top rst. Adjust the panels as needed to
ensure a tight and even t before securing to the leg poles.
Interior View of Canopy Base Feet
Side Wall
Panel
(Interior)
10334
Exterior View of Canopy Base Feet
Side Wall
Panel
(Exterior)
10334
Interior View Side Wall Panel Setup
Side Wall
Panel
10334
Insert Bungee Cord Through Grommet
05-26779-0CPage 3
2. ATTACH ENCLOSURE END AND zIPPER DOOR PANELS
When securing enclosure panels to corner legs, note that each bungee is shared with the neighboring panel.
NOTE: Door panels zippers must be closed when securing door panel.
Side Wall
Panel
10334
3. TIGHTEN THE COvER WITH TWIST TITE
™
A. Wrap the cord with plastic ball and "S" hook at the corners of the cover around the
corner leg poles. Insert "S" hook into the hole of the corner leg poles.
B. Twist each leg pole toward the inside of the shelter until the cover becomes tight
Twist the leg poles equally to ensure the cover stays aligned during tightening.
Back Panel
10336
One bungee for
both panels.
Twist-Tite™ Tighten Cover
05-26779-0CPage 4
Loading...