ShelterLogic 25763 Assembly Instructions Manual
Description Qty. Part #
54.5 Swedged Rafter Poles
8
10091
76 Swedged Leg Poles
8
10043
77 Cross Poles 1
9
10044
(Top Bend, shallow bend)
3-Way Frame Connectors
2
10046
4-Way Frame Connectors 2 10048
(Side Bend, sharp bend)
3-Way Frame Connectors
10045
4-Way Frame Connectors
10047
Polyester Green 50mm Cover
1
PCG1006
Feet Plates
This canopy must be anchored
8
10050
Bungee Cords
38
10066
Short Pins w/rings - 1/4 x 2
3/8
8 10051
Long Pins w/rings - 1/4 x 3
8
10052
TTENTION: PINS
8 -2
3/8
Pins secure legs to side bends.
8 -3 Pins secure feet plates to legs.
Pins are for legs and feet
only , and are
NOT needed
for any other part of the
frame.
DDOO NN OO TT
RREETT UU RRNN
PPRR OO DDUUCC TT TTOO
SSTTOORREE
FOORR M I SSSSINNG OORR
RR EEPP L A CCEEMEE NN TT
PPA RRTTSS
PPLEE A SS EE CCOO NN TTACCTT
CCUUSSTT OO M EE RR
SS EE RRVVICCEE::
11..88 0000 .. 552244 .. 9999 7700
10 X 20
orPlease read instructions completely bef e assembly
"
"
"
"
"
"
"
"
4
4
"
"
Model #25763
PREMIUM PARTY CANOPY
1/2
PAGE 1
150 Callender Road
Watertown, CT 06795
ShelterLogic
All Weather Shelters
TM
05-25763-0B 08/24/06
PAGE 2
1.
FRAME ASSEMBLY
Assembly is easiest if you layout all parts as
shown. There are eight - 54.5" x 2" Rafter
Poles , they are swedged on both ends, and
have 3 pre-drilled holes. The nine- 77" x
1.5" Cross Poles do not have swedged
ends. You can set aside the eight- 76" x 2"
Leg Poles , they are swedged on one end
and have pre-drilled holes at the base & the
top. It is very important that you determine
which of the 3 & 4 way connectors are
meant for the sides and which are for the
crest. The side connectors have a sharper
bend.
2. CONNECT
PIPES
Start with the center, then
assemble each side.
4. ATTACHING
LEGS
Insert both middle
legs on
one
side of the
frame,swedged
end up, then the
end legs on that
same side.
Repeat for the other side. Now
you can secure the legs
to the
side bend connectors and secure
the cover with bungee cords.
Side Bend Connectors
(sharp bend)
Top Crest Connectors
(shallow bend)
3. PLACE COVER
Place cover over frame
so that the
grommetted portion is face down,
this allows
the valance to wrap
around and cover the frame eaves.
6. SECURING COVER
Working inside, under-
neath the unit, begin with the corners.
Insert the cord
of the bungee-ball through
the grommett and around the 77" Cross Pole, then
around the ball. By doing
this from the inside it will hide the bungee-ball
and give
a cleaner look. When all
4 corners are secured, work from side to side to get an
even fit.
5. SECURING LEGS
8 Short Pins are used to secure legs to
side bend connectors.
6.1
Loading...