Shelly SENSE User Manual

USER GUIDE

WARRANTY & WARRANTY TERMS

Allterco Robotics EOOD

Soa, Bulgaria © 2017

Smart sensor with WiFi

2

USER GUIDE

Shelly® Sense Smart sensor with WiFi control

Specication

• Illumination measurement limit - 1700 LUX

• Humidity measurement range - 0~100% (±5%)

• Temperature measurement range - 0°C ~ 60°C (± 1°C)

Motion detection

• Angle - 120°

• Range – up to 5 m

IR range

• Up to 10 m range, in an unobstructed environment

LEGEND:
Button 1 – Reset

Button 2 – Power on/off
LED 1 – Cloud connection
LED 2 – AP Mode
LED 3 – State

The smart sensor with WiFi, Shelly Sense by Allterco Robotics measures temperature and
humidity, illumination, detects motion and controls appliances through IR. With Shelly Sense
you can control ACs, TVs, Hi-Fis and others. Shelly Sense has an integrated battery, which
provides up to a week of usage without power supply. Shelly may work as a standalone Device
or as an accessory to She

®

or other home automation controller.

Motion sensor

LED 1

LED 2

LED 3

Button 1

Button 2

3

Power supply:

5V/1A DC

Battery:

Li-Ion 4400mAh

Charging port:

Micro USB

Battery life:

Up to 10 days

Working temperature:

-20 ÷ 40°C

Radio signal power:

1mW

Radio protocol:

WiFi 802.11 b/g/n

Frequency:

2.4 GHz;

WiFi Operational range (depending on local
construction):

• up to 50 m outdoors

• up to 30 m indoors

Dimensions (HxD):

Device - 122 x 50 mm
Stand - 38 x 62 mm
Device & Stand - 150 x 62 mm

Buttons and indicators

Button 1

Reset

Button 2

• Press once – turn on, when the device is off

• Hold for 5 sec. – turn off, when the device is on

LED 1

• Constantly On – Active cloud connection

• Blinking – Trying to connect to cloud

LED 2

Constantly On - AP Mode

LED 3

Status

Charging

• 0-20% - LED 2 and 3 blink

• 20-60% - LED 2 blinks

• Over 60% - No indication

* When the Device is off and is connected to a charger, the LED 3 is constantly green.

4

Introduction to Shelly

®

Shelly® is an innovative Device, which allows remote monitoring of parameters and control
of appliances through mobile phone, PC or a home automation system. Shelly

®

uses WiFi to
connect to other devices. Devices can be in the same WiFi network or they can use remote
access (through the Internet). Shelly

®

works standalone, without being managed by a home
automation controller, in the local WiFi network, as well as through a cloud service, from
everywhere the User has an Internet access.

Shelly

®

has an integrated web server, through which the User can adjust, control and monitor

different Devices. Shelly

®

has two WiFi modes - Access Point (AP) and Client mode (CM). To

operate in Client Mode, the Device must be located within the range of a WiFi router. Shelly

®

devices can communicate directly with other WiFi devices through HTTP protocol. An API can
be provided by the Manufacturer.
Shelly

®

devices may be available for monitor and control even if the User is outside the range
of the local WiFi network, as long as the WiFi router is connected to the Internet. The cloud
function is activated through the web server of the Device or through the settings in the Shelly
Cloud mobile application.
The User can register and access Shelly Cloud, using either Android or iOS mobile applications,
or any web browser and the web site: https://my.Shelly.cloud/.

You can choose whether to use Shelly through the mobile application and Shelly Cloud
service, or to familiarize yourself with the Management and Setup instructions of the built-in
web interface available in this User Guide.

Technical information

• Control through WiFi from a mobile phone, PC, automation system or any other Device

supporting HTTP and/or UDP protocol.

• Microprocessor management.

CAUTION! Keep the remote control devices (mobile phones, tablets, PCs) away from
children.

CAUTION! Use the Device only with power grid which complies with all applicable
regulations. In case Shelly Sense is connected to the power grid and a short circuit
occurs, it may damage the Device.

Control your home with your voice

All Shelly devices are compatible with Amazon Echo and Google Home. Please see our step­by-step guide on:

https://shelly.cloud/compatibility/Alexa
https://shelly.cloud/compatibility/Assistant

5

MOBILE APPLICATION

FOR SHELLY

®

Allterco Robotics EOOD

Soa, Bulgaria © 2017

6

The Shelly Cloud Mobile Application

Shelly Cloud gives you the opportunity to control and adjust all Shelly® Devices from anywhere
in the world. All you need is an internet connection and our mobile application, installed on
your smartphone or tablet. To install the application please visit Google Play (Android - fig. 1)
or App Store (iOS - fig. 2) and install the Shelly Cloud app.

Registration

The first time you open the Shelly Cloud mobile app, you are asked to create an account to
manage your Shelly

®

devices.

Forgotten Password

In case you forget or lose your password, just enter the e-mail address you have used in your
registration. You will then receive instructions on how change your password.

WARNING! Be careful when you type your e-mail address during the registration, as
it will be used in case you forget your password.

fig. 1

fig. 2

7

After registering, create your first room (or rooms) - fig. 3, where you are going to add and
use your Shelly devices.

Shelly Cloud gives you the opportunity to create scenes for automatic turning on or off of the

Devices at predefined hours or based on other parameters like temperature, humidity, light
etc. (with Shelly Sense connected to Shelly Cloud).

Shelly Cloud allows easy control and monitoring by using a mobile phone, tablet or PC.

Device Inclusion

To add a new Shelly device, connect it to the power grid
following the Installation Instructions included with the
Device.

Step 1

After powering on, Shelly will create its own WiFi Access
Point (AP).

WARNING: In case the Device has not created its

own WiFi network with SSID like shellysense­16327b check if you have connected Shelly correctly by
these instructions. If you do not see an active WiFi
network with SSID like shellysense-16327b, or you want
to add the Device to another Wi-Fi network, reset it. To
reset the Device hold button 1 for 10 seconds, then LED 3
will begin flashing slowly. After 5 more seconds LED 3
will begin flashing fast, then release the button. After LED
2 turns yellow, the Device is in AP mode. If not, please
repeat or contact our customer support at: support@

shelly.cloud

Step 2

Choose “Add Device” - fig. 4.
In order to add more Devices later, use the app menu at
the top right corner of the main screen and click “Add
Device”. Type the name (SSID) and password for the WiFi
network, to which you want to add the Device.

fig. 3

fig. 4

8

Step 3

If using iOS: you will see the following screen - fig. 5

Press the home button of your iPhone/iPad/iPod. Open
Settings > WiFi and connect to the WiFi network created
by Shelly, e.g. shellysense-16327b.

If using Android: your phone/tablet will automatically
scan and include all new Shelly Devices in the WiFi
network that you are connected to (fig. 6).
Upon successful Device Inclusion to the WiFi network
you will see the following pop-up - fig. 7

Step 4:

Approximately 30 seconds after discovery of any new

Devices оn the local WiFi network, а list will be displayed

by default in the “Discovered Devices” room (fig. 8).

Step 5:

Enter Discovered Devices and choose the Device you
want to include in your account (fig. 9).

Step 6:

Enter a name for the Device (in the Device Name
field). Choose a Room, in which the Device has to be
positioned (fig. 10). You can choose an icon or add a
picture to make it easier to recognize. Press “Save
Device”.

Step 7:

To enable connection to the Shelly Cloud service for
remote control and monitoring of the Device, press
“YES” on the following pop-up - fig. 11.

fig. 5

fig. 6

fig. 7

9

fig. 8

fig. 11

fig. 12

fig. 9

fig. 10

fig. 13

10

Shelly Devices Settings

After your Shelly device is included in the app, you can
control it and change its settings. To enter the details
menu (fig. 12) of the respective Device, simply click on
it’s name.
From the details menu you may see current temperature,
humidity, illumination, motion, as well as edit its
appearance and settings. Here you can also see history
of temperature and humidity for up to a year.

EDIT DEVICE – allows you to change the Device’s name,
room and picture.
DEVICE SETTINGS – allows you to change settings
(fig. 13). For example, with Restrict login you may enter

a username and password to restrict access to the
embedded web interface in Shelly. You may automate
the Device operations from this menu as well.

Temperature Units

Setting for change of the temperature units.

• Celsius

• Fahrenheit

Motion Duration

Setting for length of motion hold state. Maximum
allowed value - 60 sec.

fig. 14

fig. 15

11

Add remote control

Shelly Sense allows direct control of devices, which are
controlled via an IR remote.

Step 1

To add a remote, open the Menu from the top right corner
on the home screen and press on “Add IR Remote” (fig.

14).

Step 2

You will be redirected to the “Add IR Remote” screen ­fig. 15. Type in Name (in the “IR Remote-Control Name”).
Choose room, for the remote. You can choose an icon
or add picture to make it easier to recognize and press
“Next”.

Step 3

Here (fig. 16) select the Shelly Sense, to which you want
to add a remote control and press “Next”.

Step 4

Here (fig. 17) you choose the type of device, that you
want to control:

• А/С

• TV

• Set-Top-Box

• Hi-Fi

Step 5

Type in the brand of the device (fig. 18), that you want to control, i.e.: LG, Samsung, Sony, etc.
The field is interactive and will filter the remaining brands, relatively to the field entry.

WARNING! The brand must be typed in English!

fig. 16

fig. 17

12

Step 6

After you have selected the brand, you will see “Choose
Device Model” (fig. 19), where you have to press the ”On”
button in the field, so you can find your remote control for
your device. After every try you will be prompted: “Press
Yes if your device has switched on successfully”. When
you find the appropriate remote, which can turn on your
device, press “Yes”. After that you will be asked “Do you
want to save this remote?”, press “Yes”.

Step 7

You will be automatically redirected to the room in
which your remote is added. You will see “Remote
saved successfully”, and the added remote. To enter
into the detail menu of every remote, press on its name.
The detail menu has all the buttons for control of every
device, and also on the top right corner - current air
temperature and humidity, illumination, motion detection,
battery percentage and name of Shelly Sense.

Edit Device - allows you to change the remote’s name,
room and picture.

Device Settings – shows you information about the
remote.

fig. 18

fig. 19

13

The Embedded Web Interface

Еven without the mobile app, Shelly can be set and controlled through a browser and WiFi

connection of a mobile phone, tablet or PC.

Аbbreviations used:

Shelly ID – unique name of the Device. It consists of 6 or more characters. It may include
numbers and letters, for example 16327b.

SSID – name of the WiFi network, created by the Device, for example shellysense-16327b.

Access Point (AP) – mode in which the Device creates its own WiFi connection point with

the respective name (SSID).

Client Mode (СМ) – the mode in which the Device is connected to another WiFi network

Initial inclusion

Step 1

After connecting Shelly to the power grid, it is ready for setup. If the Device is off, turn it on.

Step 2

Shelly creates own WiFi network (own AP), with name (SSID) such as Shellysense-16327b.
Connect to it with your phone, tablet or PC.

Step 3

Type 192.168.33.1 into the address field of your browser to load the web interface of Shelly.

General - Home Page

This is the home page of the embedded web interface. If it has been set up is correctly, you
will see information about:

• Settings menu button

• Current Mode (AP/CM)

• Network Name

• Present time

• Presence of motion

• Charging

• Temperature

14

• Humidity

• Illumination

• Battery charge level

General Settings:

In this menu, you can configure Shelly and it’s connection mode.

WiFi Settings – the WiFi connection settings

Access Point (AP) Mode: Allows the Device to operate as a WiFi access point. The User

can change the name (SSID) and the password to access the AP. After you have entered the
desired settings, press Connect.

WiFi Client Mode (CM): Allows the Device to connect to an available WiFi network. In order to
switch to this mode, the User must enter the name (SSID) and the password to connect to a
local WiFi network. After entering the correct details, press Connect.

ATTENTION! If you have entered incorrect information (wrong settings, usernames,
passwords etc.), you will not be able to connect to Shelly and you have to reset the

Device.

WARNING: If you do not see an active WiFi network with SSID like shellysense-

16327b, or you want to add the Device to another Wi-Fi network, please reset it. To
reset the Device hold button 1 for 10 seconds, then LED 3 will begin flashing slowly. After 5
more seconds LED 3 will begin flashing fast, then release the button. After LED 2 turns yellow,
the Device is in AP mode. If not, please repeat or contact our customer support at: support@

shelly.cloud

Login: Access to the Device

• Leave Unprotected - removing the notification for disabled authorization.

• Enable Authentication – you can turn authentication on or off

This is where you can change your username and password. You must enter a new username
and the new password, then press Save to save the changes.

Connect to Cloud: You can turn the connection between Shelly and Shelly Cloud on or off.

Temperature Units: Setting for change of the temperature units.

• Celsius

• Fahrenheit

15

Motion Duration: Setting for length of motion hold state. Maximum allowed value - 60 sec.

Factory reset: Return Shelly to its factory settings.

Firmware Upgrade: Shows present firmware version. If a newer version is available, officially

announced and published by the Manufacturer, you can update your Shelly Device. Click
Upload to install it to your Shelly Device.

Device Reboot: Reboots the Device.

Safety Usage

• Never use the device at temperatures lower than 0° C and higher than 40° C. Use the Device

only at a temperature between 0° C and 40° C. Exposing the Device to lower or higher
temperatures may damage it or potentially harm your health.

• Do not expose the device to direct sunlight for long periods of time.

• Do not expose the Device or its components to an open flame or throw it into fire.

• Do not throw, scratch or drop the device. It is NOT shockproof.

• Always clean the device with a dry cloth

• Do not expose the Device to moisture/liquids as a whole or its components, including the

battery. Do not use it under water! Do not use the device if it has been wet. The device is
NOT waterproof.

• Do not use any cleaning products or chemicals! They can damage the Device!

• Do not place the device directly on sand

• In case your child breaks the Device, gather the parts and do not allow your child to swallow

any of them. Small parts can cause suffocation or injuries.

• Always remove the charger from the outlet, after fully charging the battery of the Device.

• Do not allow children to charge the battery.

• Do not connect faulty USB cables and chargers to the Device.

• Do not manipulate the battery. Improper use of the battery may result in fire and even

explosion.

• Do not attempt to broach the design and/or components of the Device (including the

battery) or modify them.

• Do not open, hit, step on or violate the integrity of the Device.

• Do not interfere with the integrity of the USB power cable. Do not twist it, do not tear it, do

not bite it, do not pull it, cut it or violate its integrity.

• Avoid contact with magnets.

16

17

Warranty Terms

1. The Device’s warranty term is 24 (twenty four) months, beginning since the date of
purchase by the End User. The Manufacturer is not responsible for extra warranty terms by

the Еnd Seller.

2. The Warranty is valid for the territory of EU. The warranty is applicable in compliance with all
relevant laws and users’ rights protections. The purchaser of the Device is entitled to exercise
his/her rights in accordance with all applicable laws and regulations.

3. Warranty terms are provided by Allterco Robotics EOOD (referred hereinafter as the
Manufacturer), incorporated under the Bulgarian law, with address of registration 109 Bulgaria
Blvd, floor 8, Triaditsa Region, Sofia 1404, Bulgaria, registered with the Commercial Register
kept by the Bulgarian Ministry of Justice’s Registry Agency under Unified Identity Code (UIC)

202320104.

4. Claims regarding the Conformity of the Device with the terms of the contract of sale shall
be addressed to the Seller, in accordance with its terms of sale.

5. Claims regarding damages such as death or body injury, deterioration or damages to
objects different from the defective product, caused by a defective product, are to be claimed
against the Manufacturer using the contact data of the Manufacturer’s company.

6. The User may contact the Manufacturer via e-mail at [e-mail] for operational
problems that may be resolved remotely. It is recommended that the User contact the
Manufacturer before sending the Device for servicing.

7. The terms of removing defects depends on the commercial terms of the Seller. The
Manufacturer is not responsible for untimely servicing of the Device or for faulty repairs
carried out by unauthorized service.

8. When exercising their rights under this warranty, the User must provide the Device with the
following documents: receipt and valid warranty card with date of purchase.

9. After a warranty repair has been carried out, the warranty period is extended for that period.

10. The warranty does NOT cover any damages to the Device which occur in the following
circumstances:

• When the Device has been used or wired inappropriately, including electric shock, short
circuit or other problems in the power supply, the power grid or the radio network.

• When there has been a self-repair attempt, faulty (de)installation, modification, or
readjustment of the Device by unauthorized persons.

18

• Intentional or negligent improper handling, storing or transportation of the Device, or in the
event of non-observance of the instructions included in this warranty.;

• When a non-standard power supply, network, or faulty Devices have been used;

• When there is a non-compliance between warranty card and/or without a purchase receipt,
or attempted forgery of these documents, including (but not limited to) the warranty card or
the documents proving the purchase.

• When damages occur which were caused regardless of the Manufacturer, including but not
limited to: floods, storms, fire, lightning, natural disasters, earthquakes, war, civil wars, other
force majeure circumstances, unforeseen accidents, robbery, water damage, any damages
made by ingress of liquids, weather conditions, solar heating, any damages caused by
intrusion of sand, humidity, high or low temperature, or air pollution.

• When there are other reasons beyond manufacturing defect, including but not limited
to: water damage, ingress of liquid into the Device, weather conditions, solar overheating,
intrusion of sand, humidity, low or high temperature, air pollution.

• When there have been mechanical damages (forced opening, breaking, cracks, scratches
or deformations) caused by a hit, fall, or from another object, wrong use, or caused by not
following the instructions for use.

• When damage has been caused by exposing the Device to severe outdoor conditions such
as: high humidity, dust, too low or too high temperature. Terms of proper storage are specified
in the User Manual.

• When damage has been caused by faulty accessories, or those not recommended by the
Manufacturer.

• When damage has been caused by the use of non-original spare parts or accessories
not suitable for the specified Device model, or after repairs and changes carried out by an
unauthorized service or person.

• When damage has been caused by the use of faulty Devices.

• When damage has been caused by faulty software, a computer virus or other harmful
behaviour on the Internet, or by lack of software updates or incorrect updates by a method
not provided by either the Manufacturer or by the Manufacturer’s software.

11. The range of warranty repairs does not include periodical maintenance and inspections,
particularly cleaning, adjustments, checks, bug fixes or program parameters and other
activities that must be performed by the User (Buyer). The warranty does not cover wear of
the Device, because such elements have a limited lifespan.

19

12. The Manufacturer is not responsible for any property damage caused by a defect in the
Device. The Manufacturer is not liable for indirect damages (including but not limited to loss
of profits, savings, lost profits, claims by third parties) in connection with any defect of the
Device, nor for any property damage or personal injury arising out of or related to the use of
the Device.

13. The Manufacturer is not responsible for damage caused by circumstances independent of
the Manufacturer, including but not limited to: floods, storms, fire, lightning, natural disasters,
earthquakes, war, civil unrest and other force majeure, unforeseen accidents, or theft.

IP20

2017/10/v01

Warranty Card

Smart sensor with WiFi Shelly

®

Sensе

........................................................... ...........................................................

Serial number:

........................................................... ...........................................................

Date of purchase:

........................................................... ...........................................................

Signature of Merchant (Seller):

Please save this part of the Warranty card. For carrying out the rights under the
current warranty, you need to provide an original invoice and/or receipt, proving
your purchase was valid.

Manufacturer: Allterco Robotics EOOD
Address: Sofia, 1404, 109 Bulgaria Blvd., fl. 8
Tel.: [phone]
E-mail: [e-mail]

http://www.shelly.cloud

The Declaration of Conformity is available at:

https://Shelly.cloud/declaration-of-conformity/

Changes in the contact data are published by the Manufacturer at the official website of the
Device: http://www.shelly.cloud

The User is obliged to stay informed for any amendments of these warranty terms before
exercising his/her rights against the Manufacturer.

All rights to trademarks She

®

and Shelly®, and other intellectual rights associated with this

device belong to Allterco Robotics EOOD.