Instruction Manual
Model: PL729
2000W Bagless Vacuum Cleaner
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Carefully read this manual before using this appliance.
Ensure that you know how the appliance functions and how to operate it.
Maintain the appliance in accordance with the instructions to ensure that it functions properly.
Keep this manual with the appliance. If the appliance is to be us ed by a third party, this instruction
manual must be supplied with it.
The safety instructions do not by themselves eliminate any danger completely and proper accident
prevention measures must always be used.
No liability can be accepted for any damage caused by non-compliance with these instructions or
any other improper use or mishandling.
Do not use this appliance if it has been dropped or damaged in any way, or if the supply cord is
damaged.
PACKAGE CONTENTS
1 x 2000W Bagless Vacuum Cleaner
1 x Stainless Steel Telescopic Tube
1 x Flexible Hose
1 x Floor Brush
1 x Instruction Manual
Confirm all parts before disposing of carton. Safe ly dispose of all plastic bags and other packaging
components. They may be potentially dangerous to children.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution should always be followed.
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
WARNING - To reduce the risk of fire, electric shock, or injury:
1. Do not leave vacuum cleaner when plugged in. Unplug from outlet when not in use and before
servicing.
2. To reduce the risk of electric shock, do not use ou tdoors or on wet surfaces.
3. If the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or
dropped into water, take it to a service centre.
4. Do not use with damaged supply cord or plug. If the supply cord is damaged, the manufacturer
or its service agent or a similarly qualified person must replace it in order to avoid a hazard.
5. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
6. Children should be supervised to ensure that they do not play with the appliance.
7 Do not carry by the cord, use cord as a handle, close door on cord, or pull cord around sharp
edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated surfaces.
8. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
9. Do not handle plug or vacuum cleaner with wet hands.
10. Do not put any object into openings. Do not use with any opening or outlet blocked. Keep free
of dust, lint, hair and anything that m ay reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the body away from openings and moving
parts.
12. Turn all controls off before unplugging.
13. Use extra care when cleaning on stairs.
14. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where
they may be present
15. Hold plug when rewinding onto cord reel. Do not allow plug to whip when rewinding.
16. Unplug before connecting the hose.
17. Do not pick up anything that is burni ng or smoking, such as cigarettes, matches, or hot ashes.
18. Do not use without filters in place.
19. This appliance is double insulated for your protection. Do not attempt to repair a double
insulated appliance.
ASSEMBLING THE VACUUM CLEANER
Always remove the plug from the power socket before fitting or removing accessories!
1. Fitting the flexible hose
Insert the flexible hose into the air intake duct at the front of the appliance. Press until it clicks into
position.
2. Removing the flexible hose
Remove the plug from the power socket. To release the flexible hose, firmly squeeze the release
buttons on both side and pull out from the air intake duct.
3. Fitting the extension tube and floor brush
Simply insert the tube into the available end of the flexible hose and insert the floor brush to the
other end of the tube. Adjust the telescopic tube to the desired length.
Before using the appliance, unwind a sufficient length of cable and insert the plug into a suitable
220-240V ~ 50Hz power socket. A yellow mark on the po wer cable shows the ideal cable l ength.
Do not extend the cable beyond the red mark!
NEVER PULL OUT OR RETRACT THE CORD WHILE THE MACHINE IS RUNNING.
1. Insert the power plug into the wall outl et.
2. Press the ON/OFF button to switch the appliance on.
3. To rewind the power cord, press down on the cord rewind button (carry handle) with one hand
and guide the power cord with the other hand to ensure that it does not whip causing damage or
injury.
4. To adjust the suction power, rotate the speed control knob clockwise to increase the suction and
anti-clockwise to decrease the suction.
On/Off Button &
Speed Control Button
Cord Rewind Button &
Carry Handle
MOTOR THERMOSTAT
Important: The motor of this vacuum cleaner is equipped with a protective thermostat. If for some
reason the vacuum cleaner should overheat, the thermostat will auto matically turn the unit off.
Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch. Remover the
dust barrel and empty. Clean all filters. Allow the unit to cool for approximately 1 hour. To restart,
plug into wall outlet and turn switch back on.
EMPTYING THE VACUUM CLEANER
Emptying the dust barrel
Always unplug the unit from electrical outlet before removing the dust barrel.
1. Press the knob on the top of the dust barrel.
2. Lift dust barrel up.
3. Hold the barrel over a rubbish bin or other suita ble area for collecting the contents of the barre l.
Press the knob at the bottom end of dust barrel to open the dust barrel cover. The contents are
emptied from the bottom of the barrel.
1 2 3
It is imperative that after the dust barrel is emptied, it is reassembled correctly.
Ensure that the HEPA filter is correctly positioned & LOCKED into place and that the rubber
grommet on the lid of the dust barrel has not been removed o r tampered with, is mounted
correctly in place, free from kinks or distor tion and correctly seals the HEPA filter to the vacuum
intake.
Correct installation of rubber grommet
CLEANING THE HEPA FILTER
The HEPA Filter needs to be cleaned regula rly; the frequency will depend entirely on the
environment it is used in. If you notice a lack of suction the HEPA Filter should be removed and
thoroughly washed. Always ensure the HEPA filter is completely dry before refitting to the dust
barrel.
Removing & Cleaning the HEPA filter
1. Remove the dust barrel as described a bove.
2. Open the dust barrel cover and take out the HEPA filter by turning it anti-clockwise.
3. Remove the mesh filter cover from the HEPA filter and it wash under water.
HEPA Filter Mesh Filter Cover
4. The HEPA Filter should be thorough ly washed und er a m a ins pressure tap and allowed to dry
completely before refitting to the dust ba r rel .
5. Replace the mesh cover to the HEPA filter insuring it is correctly positioned in place.
6. Replace the HEPA filter into the dust barrel and lock it in place by turning it tightly clockwise.
7. Pay special attention to ensure that the HEPA filter is correctly positioned & LOCKED into place
and that the rubber grommet on the lid of the dust barrel i s m ou nte d correctly in place.
8. Refit the dust barrel to the vacuum cleaner. For reassembly, reverse the disassembly procedure.
Removing & Cleaning the Air Outlet Filter
1. Press the air outlet grille knob to open
2. Remove the air outlet filter for cleaning or changing.
3. Inspect the exhaust outlet to ensure it is free from debris. If there is a build-up of debris, the
vacuum has not been reassembled properly . T h is build-up may cause overheating, lack of suct ion,
damage to the impellor & motor and ultimately failure of the appliance. It should be returned to a
service agent or a similarly qualified person for servicing.
4. Refit the exhaust filter and grille to the vacuum cleaner.
Removing & Cleaning Pre-Motor Filter
1. Remove the dust barrel as described a bove.
2. Lift out the pre-motor filter for cleaning or changing.
Pre-Motor Filter
PARTS & SERVICING
Replacement parts are available for this vacuum cleaner including hoses, telescopic tubes, floor
brushes and filter packs (HEPA filter, pre-motor filter and exhaust filter).
Please contact Prolink Asia Limited Ph: 09 274 3650 for servicing, rep lacement filter packs and spare
parts.
PRECAUTIONARY MEASURES
All filters should be checked regularly for signs of damage, preferably after each use. The filters
must be replaced immediately if they become da m a ged. Always disconnect the vacuum from the
electrical outlet when checking the filters.
This appliance is equipped with a motor protective thermostat. If for some reason the vacuum
cleaner should overheat, the thermostat will automatical ly t urn t he unit off. Should this occur turn
off the switch and unplug the vacuum cleaner from the wall outlet, change dust bag and clean
filters. Allow the unit to cool for approximately 1 hour. To restart, plug into wall outlet and turn the
switch back on.
This vacuum cleaner is equipped with a plug and a cord, which rolls up automatically.
If any of these parts get damaged, it must be repaired by a qualified repairman or electrician.
TO PREVENT DAMAGE TO YOUR VACUUM CLEANER
1. Never unwind or rewind the cord while the vacuum cleaner is turned on or plugged in, this may
produce arcing of the terminals in the cord rew i nd mechanism and cause an open circuit. Do not
extend the cable beyond the red mark.
2. Be sure to check that the rubber grommet and all filters, particularly the HE PA filter is correctly
in place after removal, if not, then damage to the vacuum cleaner motor can occur.
3. If the hose inlet, the hose, tube or nozzle attachments are blocked, switch off the vacuum
cleaner. Clear the blockage before you attempt to start the vacuum cleaner again.
4. Do not obstruct the air outlet. Do not operate this vacuum cleaner with it standing on its back
side i.e. air outlet sitting on the ground . Only operate this unit when all 3 wheels are on th e
ground.
5. Do not operate the vacuum cleaner too close to heat sources such as heaters, open fires,
cigarette butts etc
6. Never run the vacuum cleaner without all the filters and parts correctly in place.
7. Before you start using the vacuum cleaner, remove any large or sharp objects from the floor in
order to prevent damage to the floor brush, tube, hose, and filters.
Failure to observe the above precautions may void any warranty
TECHNICAL SPECIFICATIONS
Model PL729
220-240V ~ 50Hz
2000 Watt
Loading...