Sheenway Asia ZW4202 User Manual

45654 Instructions 8/25/2010 10:11:46 AM

45654

Wireless Lighting Control

Energy Monitoring Outdoor Module

R Z-Wave® Certified Wireless Lighting Control

Add

Add callout for Program/manual control pushbutton

®

Thank you for your purchase of a GE Z-Wave
lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product
family includes a variety of devices to control lighting in your home. It is up to you whether you want to control one
room or your entire house and whether you want to do it all now or start with one room and add more over time.

control device. Z-Wave technology is designed to automate

This module is one component of a Z-Wave

®

control system and is designed to work with all other Z-Wave enabled
devices in a home control network. It will also act as a wireless repeater to insure that commands intended for another
device in the network are received, thereby extending the range of the wireless controller. Z-Wave devices of other
types and brands can be added to the system and will also act as range extenders if they support this function of
repeating the signal received to other nodes in the system.

The device plugged into this module must not exceed 900 Watts (Incandescent); 1800W (15A) Resistive; or
1 HP Motor load.

There are no user serviceable parts in this unit.

To reduce the risk of electric shock, this product has a grounding type plug that has a third (grounding) pin. This plug
will only fit into a grounding type power outlet. If the plug does not fit into the outlet, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.

Page 1 of 6

45654 Instructions 8/25/2010 10:11:46 AM

RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS

The Load-Sense feature on this Z-Wave product will turn the power to the connected device ON when a change in the
load is detected. Z-Wave connected devices should always be unplugged before performing any service or
maintenance of the devices. Mount above ground with receptacle pointed down using mounting tab.

Controlling Appliances:

Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be
in a different room than the controlled appliance, also an unintentional activation may occur if the wrong button on the
remote is pressed. Z-Wave devices may automatically be powered on due to timed event programming. Depending
upon the appliance, these unattended or unintentional operations could possibly result in a hazardous condition. For
these reasons, we recommend the following:

1. Assign Z-Wave controlled appliances to device numbers 10 – 18 on the GE remote. The likelihood of
unintentionally turning on the appliance will be reduced significantly because the “Shift” button will need to be
pressed before pressing device numbers 10-18.

2. Z-Wave devices controlling appliances should be removed from “All” control setting. Instructions on how to do
this are included in the manual for your GE remote.

3. Do Not include Z-Wave devices in Groups or Scenes if they control appliances.

4. Do Not use Z-Wave devices to control electric heaters or any other appliances which may present a
hazardous condition due to unattended or unintentional or automatic power on control.

5. Double check programs for accuracy before using them.

NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT

Z-Wave enabled devices should never be used to supply pow er to or control the On/Off status of medical
and/or life support equipment!

Wireless Range

This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 65 feet. Actual
performance in a home depends on the number of walls between the remote controller and the destination device, the
type of construction and the number of Z-Wave enabled devices installed in the control network. Every Z-Wave
enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps
eliminate “RF dead-spots”.

Things to consider regarding RF range:

x Each wall or obstacle (i.e.: refrigerator, big screen TV, etc.) between the remote and the destination device will

reduce the maximum range of 100 feet by approximately 25-30%.

x Brick, tile or concrete walls block more of the RF signal than walls made of wooden studs and plasterboard

(drywall).

x Wall mounted Z-Wave devices installed in metal junction boxes will suffer a significant loss of range

(approximately 20%) since the metal box blocks a large part of the RF signal.

Page 2 of 6