Shaw ATLAS PVR Universal Remote Control User Manual
ATLAS PVR Universal Remote Control
Users Guide
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Programming Device Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Programming TV/VCR Combo Control . . . . . . . . . . . . . . . . . . . . . . . 10
Searching for Your Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Checking the Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using Learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Learning Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Programming a Learned Key . . . . . . . . . . . . . . . . . . . . . . . . .13
Deleting a Single Learning Key. . . . . . . . . . . . . . . . . . . . . . . .14
Deleting All Learned Keys in a Specific Mode . . . . . . . . . . . . 14
Programming Channel Control Lock . . . . . . . . . . . . . . . . . . . . . . . .15
Unlocking Channel Control. . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Locking Channel Control to CBL. . . . . . . . . . . . . . . . . . . . . . . 16
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Unlocking Volume Control for a Single Device (Individual
Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Unlocking All Volume Control (Global Volume Unlock) . . . . .17
Locking Volume Control To One Mode (Global Volume Lock) 17
Programming ID Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Using the Master Power Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Programming the Master Power Key . . . . . . . . . . . . . . . . . . .19
Using the Master Power Key. . . . . . . . . . . . . . . . . . . . . . . . . .19
Clearing the Master Power Key . . . . . . . . . . . . . . . . . . . . . . .19
Re-Assigning Device Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Clearing Custom Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Setup Codes for Audio Amplifiers. . . . . . . . . . . . . . . . . . . . . . 24
Setup Codes for Audio Amp/Tuners . . . . . . . . . . . . . . . . . . . .25
Setup Codes for Miscellaneous Audio . . . . . . . . . . . . . . . . . . 28
Setup Codes for Cable Boxes/Converters . . . . . . . . . . . . . . . 28
Setup Codes for DVD Players . . . . . . . . . . . . . . . . . . . . . . . . .29
Setup Codes for PVRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Setup Codes for Satellite Receivers . . . . . . . . . . . . . . . . . . .33
Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Setup Codes for Video Accessories . . . . . . . . . . . . . . . . . . . .43
2
INTRODUCTION
The Atlas PVR Universal Remote Control by Universal
Electronics is our latest generation universal remote
control. Its sophisticated technology allows you to
consolidate up to five of your original home
entertainment remote controls into one easy-to-use
product. Moreover, its packed with advanced features
such as:
• Preprogrammed control to operate the cable
converter supplied by your cable service provider
• Dedicated keys to control popular functions on your
DVR/PVR (Digital/Personal Video Recorder)
• Programmable Master Power key for master on/off
control of your home entertainment equipment with
a single keystroke
• Channel Lock to lock channel selection only to the
cable converter
• Volume Lock to lock volume controls to on e mod e or
individual modes
• Device Key Re-Assignment to remotely control a
second (duplicate) device
• Code Search to help program control of older or
discontinued components
• Color-coded keys to quickly locate popular
functions
• Code library for popular video and audio devices
Before using the product, you will need to install the
enclosed batteries and also perform some programming
to operate the specific home entertainment devices you
wish to control.
Please follow the instructions detailed in this manual to
set up the unit and then start enjoying your new remote
control and cable service.
3
FEATURES AND FUNCTIONS
Use the illustration below to locate features on the Atlas
PVR Universal Remote Control and then study the Key
Charts (on the next three pages) to learn how they
function.
To find out what type of devices can be controlled by
each device key after programming, see “Device Table”
on page 7.
4
Key Charts
Key Function
Use SETUP for all programming
sequences.
Press PWR once to turn on or off a home
entertainment device. For MASTER
POWER control, see “Using the Master
Power Key” on page 18.
Press AUX, DVD, AUD, TV, or CBL once to
select a home entertainment device to
control. Also see “Device Table” on
page 7.
Each device key has an embedded LED
(red light) that blinks upon selection
and indicates the remote control is
working and (after programming) is
sending signals.
Use GUIDE to display the program
guide.
Press MENU/SETTINGS once to display
available menu options.
Use INFO to display the current channel
and program information.
Use DAY+ (or DAY-) to move a day
forward (or back) on your cable
converter’s program guide.
Use the Cursor keys to move the cursor
in the program guide and menu screens
and to navigate within the interactive
service.
Use OK/SELECT to choose options, PPV
events, and to tune programs from the
program guide.
Use PAGE+ (or PAGE-) to page up (or
page down) through menu screens and
the program guide.
Use EXIT to exit out of your cable
converters menu and guide.
Use A, B, or C to access additional cable
features (future functionality).
Use VOL+ (or VOL-) to raise (or lower)
the audio volume.
Use FAV to cycle through your favorite
channels stored in the program guide.
5
Key Function
Use CH+ (or CH-) to select the next
higher (or lower) channel.
For DVD players, use these keys to skip
forward (or reverse) through chapters.
For amplifiers/receivers, use these keys
to select the next higher (or lower)
preset station.
Press MUTE once to turn the sound off
or on.
Press LAST once to recall the last
channel.
Press SKIP to skip forward in
predetermined increments.
Press SHAWONDEMAND to access Shaw
Video On Demand VOD services.
Press MUSIC to access the available
Digital Music services.
Use to command your PVR to
instantly replay the last 15 seconds of a
program you are watching.
Press LIST once to display a list of
recorded shows on your PVR.
Press LIVE to return to watching live TV.
In all modes except CBL, use REW, PLAY,
FFWD, STOP, and PAUSE to control a
VCR, DVD player, or a PVR (after
selecting a desired device). To record in
the VCR mode, press REC twice.
In the CBL mode, use these keys to
control the DVR/PVR functions of the
set-top box.
Use the keypad numbers (1-9, and 0) to
directly tune channels (e.g., 009).
For amplifiers/receivers, use the keypad
numbers to select inputs 1 through 10.
P
ress
HD/ZOOM
ratio of the show you are watching. (Not
available on all set-top boxes)
once to change the aspect
.
6
Key Function
Use PIP ON-OFF to switch the PictureIn-Picture feature on or off (if available
on your TV or cable service).
Use PIP SWAP to switch images and
sound between the main and window
pictures, or to swap tuners on dualtuner PVRs.
U
se
PIP MOVE
to different positions in the main picture
Use PIP CH+ (or CH-) to select the next
higher (or lower) PIP channel.
In the CBL mode, use VIDEO SOURCE to
view other video sources (A or B)
instead of cable.
In all other modes, use VIDEO SOURCE
to watch TV or video programs on a
desired device.
For amplifiers/receivers, use VIDEO
SOURCE to select an input source.
Device Table
NOTE: Please refer to the table below when
performing the instructions in
“Programming Device Control” on page 8 or
“Programming TV/VCR Combo Control” on
page 10.
After programming, theAtlas PVR Universal Remote
Control will be able to control the following types of
devices:
to move the window picture
.
Device Key Controls these types of devices
VCR, TV/VCR Combo, PVR (Personal
Video Recorder), or extra PVR Player
DVD Player
Audio Amplifier, Tuner, or Receiver
Te l e v i s i o n
Cable Box (Converter) or Satellite
Receiver, including PVR and VOD
controls
7
INSTALLING BATTERIES
❶
❷
❸
1. On the back of the remote control, push the
tab and lift off the battery cover.
2. Locate the two (2) enclosed AA batteries.
Match the + and - marks with those in the
battery case, then insert them.
3. Align the cover’s keys with the case’s holes and
4. Test the remote control by pressing any mode
press the cover back into place. The tab should
click when the cover is locked.
key (e.g., TV). If the batteries are inserted
correctly, the LED (red light) will blink once.
NOTE: When batteries need replacement, the remote
control will cease to operate. Replace the
batteries and the unit will be restored to its
full functionality, complete with your favorite
settings.
PROGRAMMING DEVICE CONTROL
The Atlas PVR Universal Remote Control is
preprogrammed to operate the cable box (converter)
provided by your cable system, an RCA TV, a Toshiba
DVD player, an RCA VCR (as an AUX device), and a
Pioneer audio receiver. To control devices other than the
default brands, perform the following steps; otherwise
skip this section.
8
NOTES: For TV/VCR Combo control, skip this section
and perform the instructions on “Programming TV/VCR Combo Control” on page 10.
Also refer to “Device Table” on page 7 to find
out which devices can be programmed onto
each device key.
If you have another brand of cable converter
or a satellite receiver you would like to control,
you’ll need to unlock the cable ID Lock before
changing the converter code (see “Programming ID Lock” on page 18).
1. Turn on a device and, if applicable, insert
NOTE: Please read steps 2 through 4 completely
2. On the remote control, press a device key once
3. Use the “Manufacturer’s Codes” starting on
NOTE: If the selected mode key emits a long blink,
4. Aim the remote control at the device and
video media, (e.g., cassette or disc).
before proceeding. Highlight or write down
the codes and device you wish to program
before moving on to step 2.
(i.e., AUX, DVD, AUD, TV, or CBL); it will blink
once. Then press and hold SETUP until the
selected mode key blinks twice.
page 24) to locate the type of device and
brand name and then enter the first four-digit
code for your device. If performed correctly,
the selected mode key will blink twice.
the entry is invalid. Repeat steps 2 through 3
and try entering the same code again.
press PWR once. The device should turn off. If
it does not, repeat steps 2 through 3, trying
each code for your brand until you find one
that works. If it still does not respond, try
searching for the code (see “Searching for
Your Code” on page 11).
NOTE: If the device does not have a PWR key, press
the(Play) key.
5. Repeat steps 1 through 4 for each device you
want the remote control to operate. For future
reference, write down each working device
code in the boxes on the following page.
AUX Code
Device Type:___________________
9
DVD Code
Device Type:___________________
AUD Code
Device Type:___________________
CBL Code
Device Type:___________________
TV Code
Device Type:___________________
PROGRAMMING TV/VCR COMBO CONTROL
If you own a TV/VCR Combo, perform the following
instructions to control this device:
1. Turn on your TV/VCR Combo and insert a
2. On the remote control, press AUX once; it will
video cassette.
blink once. Then press and hold SETUP until
the AUX key blinks twice.
3. Use the “Manufacturer’s Codes” starting on
page 24 to locate the brand name and enter
the first four-digit code for your TV/VCR
Combo. If you perform this procedure
correctly, the AUX key will blink twice.
NOTE: If the AUX key did not blink twice after enter-
ing the codes last digit, repeat steps 2 through
3 and try entering the same code again.
If you’ve located a TV/VCR setup code that
works for your TV/VCR Combo and a separate
TV code is also listed, you’ll need to program
this code into the remote control to access volume control (see “Programming Device Control” starting on page8).
10
4. Aim the remote control at your TV/VCR
Combo and press PWR once. The device
should turn off. If it does not respond, repeat
steps 2 through 3, trying each code listed for
your brand until you find one that works. If it
still does not respond, try searching for the
code (“Searching for Your Code” starting on
page 11).
5. For future reference, write down each working
device code in the boxes below:
TV/VCR Code
TV Code (if used)
SEARCHING FOR YOUR CODE
If your home entertainment device does not respond to
theAtlas PVR Universal Remote Control after trying all
of the codes listed for your brand, or if your brand is not
listed at all, try searching for your code.
For example, to search for a code for your TV:
1. Turn on your TV.
2. On the remote control, press TV once; it will
3. Enter 9 9 1. The TV key will blink twice.
blink once. Then press and hold SETUP until
the TV key blinks twice.
4. Aim the remote control at the TV and press
5. Press CH+ one or more times and stop when
NOTE: In the search mode, the remote control will
6. Press SETUP once to lock in the code. The TV
PWR once.
the TV turns off.
send IR codes from its library to the selected
device, starting with the most popular code
first.
key will blink twice.
11
7. To search for the codes of your other devices,
repeat steps 1 through 5, but substitute the
appropriate key (e.g., AUX, DVD, AUD, or CBL)
for the device you are searching for.
CHECKING THE CODES
If you have set up theAtlas PVR Universal Remote
Control by searching for your device code (on the
previous page), you may need to find out which fourdigit code is operating your equipment.
F
or example, to find out which code is operating your TV
1. On the remote control, press TV once; it will
2. Enter 9 9 0. The TV key will blink twice.
blink once. Then press and hold SETUP until
the TV key blinks twice.
:
3. To view the code for the first digit, press 1
NOTE: If a code digit is 0, the selected mode key will
4. Repeat step 3 three more times for the
5. To check for other device codes, repeat steps 1
once. Count the number of times the TV key
blinks (e.g., 3 blinks = 3) and write down the
number in the leftmost TV Code box on
page 10.
not blink.
remaining digits. Use 2 for the second digit, 3
for the third digit, and 4 for the fourth digit.
Finish writing down the code in the TV Code
boxes on page 10.
through 4, but substitute the appropriate key
(e.g., AUX, DVD, AUD, or CBL) for the device
you are checking. Write down the codes in the
appropriate boxes on page 10.
USING LEARNING
The Atlas PVR Universal Remote Control includes a
Learning feature so you can add functions that are
unique to your home entertainment devices (e.g.,VCR
T
racking Up or Down). However, there are some
considerations
Learning Precautions
• Your original remote controls must be in working
order for learning to work properly.
.
12
• Learned keys are mode-specific, so each one can
store a unique function for each mode.
• Do not use the following keys for learning: Device
Keys, SETUP, Record (•), Tune-In Keys.
• Learning capacity is approximately 16 to 25 keys,
depending on the code being learned.
• Certain device functions are not learnable including
multi-frequency types, some high frequency ones,
and other unusual formats.
• For optimum learning, avoid high levels of ambient
light such as natural sunlight or energy-efficient
fluorescent lights.
NOTE: Please have your original remote controls
handy before programming learning.
Programming a Learned Key
NOTE: If more than 15 seconds pass between key
presses, the remote exits programming.
1. Press and hold SETUP until the last-selected
mode key blinks twice, then press 9 7 5.
NOTE: If the LED displays one long flash instead,
either your batteries are low, or the Atlas PVR
Universal Remote Control has a memory fault.
In either case, the remote will not learn a new
key. See “Additional Information” on page 23.
2. Press a mode key once (i.e., AUX, DVD, AUD,
TV, or CBL) to assign a mode for learning, then
the key that will learn the new code.
3. Place the Atlas PVR Universal Remote Control
head-to-head (about 2" apart) from your
original remote control. Also locate the key
(on your original remote control) that you
want the Atlas PVR Universal Remote Control
to learn.
2"
4. On the original remote, press and hold the key
to be learned. The Atlas PVR Universal
Remote Control’s LED will blink rapidly, then
13
turn off. Continue holding the key on the
original remote until the Atlas PVR Universal
Remote Control’s LED blinks twice.
NOTE: If the LED displays one long blink, a learning
5. Repeat steps 2 through 4 for another mode
Deleting a Single Learning Key
T
his process returns the key to its original programmin
for the mode you select. You can also delete learned
programming by teaching a different function to the key
(see “Programming a Learned Key” on page 13)
NOTE: If more than 15 seconds pass between key
1. Press and hold SETUP until the last-selected
error has occurred. Try repeating this step
again until a successful capture occurs. If the
function is still not captured, press and hold
SETUP to exit programming and review the
“Learning Precautions” on the previous page.
If needed, also see “Troubleshooting” on
page 21. After review, start programming
again at step 1.
and/or key or press and hold SETUP to exit
programming.
g
presses, the remote exits programming.
mode key blinks twice, then press 9 7 6.
2. Press a mode key once (i.e., AUX, DVD, AUD,
3. Press the key containing the learned function
4. Repeat steps 2 through 3 for another key or
Deleting All Learned Keys in a Specific Mode
NOTE: If more than 15 seconds pass between key
1. Press and hold SETUP until the last-selected
TV, or CBL).
to be deleted twice. The remote will blink
twice.
press and hold SETUP to exit programming.
presses, the remote exits programming.
mode key blinks twice, then press 9 7 6.
14
Loading...