Sharper Image Steady Flying Wi-Fi Camera Drone User Manual

STEADY FLYING WI-FI CAMERA

Item No. 207162

User Guide

Thank you for choosing the Sharper Image Steady Flying Wi-Fi Camera.
Please take a moment to read this guide and store it for future reference.

-1-

CONTROLLER COMPONENTS

POWER INDICATOR

SPEED BUTTON

POWER SWITCH

UP / DOWN AND
TURN LEFT / TURN
RIGHT LEVER

HEADLESS MODE
BUTTON

DANCING BUTTON

LED CONTROL

FLIP BUTTON

FORWARD / BACKWARD
TRIM BUTTON

FORWARD / BACKWARD AND
LEFT SIDE / RIGHT SIDE LEVER

BANK LEFT / BANK RIGHT
TRIM BUTTON

SETTING UP THE CONTROLLER/DRONE

INSTALLING THE CONTROLLER BATTERIES:

• Unscrew the battery cover and insert 4 AA batteries, making sure you
match them to their corresponding polarities

• Reattach the battery cover

-2- -3- -4-

INSTALLING THE PROTECTOR AND LANDING GEAR

• Put the landing gear into the main body and fix it with the screw as seen in
Picture 1

• Put the protection circle into the main body and fix it with the screw as seen in
Picture 2

Picture 1

Picture 2

CHARGING YOUR DRONE BATTERY

BATTERY WARNING:

Lithium Polymer batteries can expand, burst or catch fire if used incorrectly, causing
both property damage and/or personal injury. It is essential that you follow all the
included instructions and safety warnings in full. The manufacturer, distributors and
retailers will assume no liability for the failure to comply with these safety instructions
and warnings.

CHARGING INSTRUCTIONS:

• The battery must be removed from the product before charging

• If the battery has just been used, please let it cool down to room temperature
before charging

• Charging must only be undertaken by an adult, using only the charger included
with this product

• Always charge the battery on a non-flammable, heat-resistant surface with non­flammable surroundings

• Connect the battery to the USB charging cable

• Connect the USB charging cable to your USB charging devices. The Red LED
on the USB will turn off while charging and will turn on once the battery is fully
charged. It takes around 60 minutes to fully charge the battery. Never continue to
charge the battery after the Red LED has turned on

• Lithium Polymer batteries do not last forever. If your battery becomes damaged in
a crash or no longer charges properly, immediately replace it with a new battery.
To prolong the life of your battery, it is always best to retain a bit of charge in
your battery prior to charging it. NOTE: Only use the USB charging cable that was

included with the device

SAFE FLIGHT ENVIRONMENT

• Make sure the surrounding area is free of all people, pets or other obstacles before
you start to fly

• The drone is designed for outside flying, or indoor flying if you have enough space
(do not use in strong wind)

• Leave 1.5 meters between you and the drone at all times

SETTING UP THE SIGNAL CONNECTION

STEP 1

Press down on the camera and push the cover of the Battery Housing to the backside
(Picture 1) — this will open the cover. Connect the Battery Plug Cable to the Battery
Socket Cable, making sure you follow the “One Orientation” fit design of the plug
and socket. DO NOT ATTEMPT TO CONNECT IT THE WRONG WAY (Picture 2). Insert the
Battery into the Battery Housing (Picture 3). Close the cover. Turn on the Power Switch
on the Drone. The LED on the Drone will start to flash. Place the Drone down on a flat
surface.

STEP 2

Picture 1 Picture 2

Press down on the controller Power Switch to turn the power
on. The controller will make ONE short BEEP sound and
the red LED will flash. To pair the signals of the Drone and
the Controller, you must raise the Up/Down Lever on the
controller all the way to the top. It will make one short BEEP
sound. Next, lower it all the way to the bottom. It will make
one short BEEP sound. The LED on the Drone will remain on,
indicating that the signals have been paired.

STEP 3

Always turn the Drone’s Power Switch to the Off position after
flight.

STEP 4

Always turn the controller off after flight. Remove all batteries
if the drone will not be used for an extended period of time.

Picture 3 Picture 4

FLIGHT ADJUSTMENT SECTION

When you lift your Drone into the air and don’t use any of the other direction levers,
your Drone should simply hover in one spot without moving in any other direction. If it
doesn’t, follow these instructions to get your Drone to hover. This is called TRIMMING,
and it is always needed before your Drone’s first flight.

AUTO TRIM FUNCTION

Push both control levers to the positions shown in the
picture and hold them for one second. The lights on the
drone will start to flash. Now the drone is recovered to its
original factory settings and is ready to fly again.

HEADLESS FUNCTION

Press the Headless Button once to enter Headless Mode.
The Front Red LED on the Drone will flash. To quit Headless
Mode, press the Headless Mode Button again.

REPLACING BLADES/FIXING ISSUES

BLADE REPLACEMENT:

Your Drone blades are very strong, but sometimes they can get damaged during
a crash. You have spare blades in the box and replacing them is as easy as simply
placing a new one over the motor bar. You must always replace an A Blade with an A
Blade, and a B Blade with a B Blade.

DRONE NOT LIFTING OR NOT FLYING IN THE PROPER DIRECTION:

• The most common reason for a Drone not lifting or flying properly in a chosen
direction is that you have hair or debris wrapped around one or more of the
blades. Simply remove the debris and blade, then place the blade back on

• The batteries in the Drone and/or Controller need charging or replacing

• You may have knocked your Trim Button settings out of sync. Follow the
instructions in the beginning of this manual to reset back to factory settings, then
re-trim as needed

WIFI CAMERA SETUP:

1. INSERT THE SMARTPHONE

Pull out the smartphone holder and place the smartphone inside:

2. SCAN THE QR CODE BELOW OR SEARCH FOR AND DOWNLOAD THE
“WIFI UFO” APP TO YOUR DEVICE.

3. SETUP INSTRUCTIONS

• Turn your Drone to the On position. The Drone is now sending out its own Wi-Fi
network signal

• Open the SETTINGS menu on your device and search for new Wi-Fi networks. You
should be able to see a new one called “Wi-Fi UFO-XXXXX” (switch your current
Wi-Fi network connection on your device to this new network

• Open the Wi-Fi UFO app and press the PLAY icon. You should now be able to see
the footage from the camera on the screen of your device

• You can now choose to fly the drone using your smartphone screen or the
controller. If using the controller, you can now clip your smartphone to the clip on
top of the controller

WARNING: For beginners, we advise that you always fly the drone
using the controller. Flying using a smartphone screen is very
difficult.

APP FUNCTIONS

1. Go back

2. Take photo

3. Record video

4. Photo and video playback

5. Drone speed

6. Control reverse (when flying in Smartphone
Screen Mode, you can switch controls if you’re
left handed)

7. Gravity sensor mode

8. Switch between controller flying and smartphone
flying

9. Advanced functions (including VR mode)

CONTROLLING BY SMARTPHONE
(

FOR ADVANCED USERS ONLY):

• Press button 8 to switch to Smartphone Screen
Mode

• Use the smartphone screen controls in the exact
same way you would use the controller

HOW TO TAKE A PHOTO/VIDEO

1. Take a photo by pressing the Photo Button once. The photo will be captured
and saved to your smartphone.

2. Start filming by pressing the Video Button once, then press it again to stop
filming. The video will be captured and saved to your smartphone.

3. To view Photos and Videos, press the Photo and Video Playback Button , where
it will take you to the media storage interface. Press the Photo Button to view
saved photos. Press the video button to view saved videos.

4. To return to the normal app screen, press the Go Back button .

WARNINGS

• This device is designed for ages 14+

• Adult supervision is always advisable with flying toys

• Always ensure your flight area is completely free of obstacles before taking off,
and that the drone is always flown in excess of 1.5 meters from yourself and
others

• Remove all batteries from the drone and controller when not in use

• Never overcharge

• Never leave unattended when charging

• Never touch the drone’s motors during or after flying as they can get hot

• Never touch the blades when they are in motion

• If the drone becomes damaged, stop using it immediately

• Do not dispose of any drone or controller parts in normal garbage; all parts should
be taken to your local recycling center

• The battery in the drone should never be exposed to any form of high temperature
(never dispose of it in a fire)

WARRANTY/CUSTOMER SERVICE

Sharper Image branded items purchased from SharperImage.com include a 1-year
limited replacement warranty. If you have any questions not covered in this guide,
please call our Customer Service department at 1 [phone]. Customer Service
agents are available Monday through Friday, 9:00 a.m. to 6:00 p.m. ET.

-5- -6- -7- -8-