Sharp XR-40X, XR-30XDM Operation Manual

Download

Page 1

MULTIMEDIA PROJECTOR

MODEL

XR-40X XR-30X XR-30S

OPERATION MANUAL

Introduction Quick Start

Setup

Connections

Basic

Operation

Useful

Features

Appendix

Page 2

IMPORTANT

• For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information.

• Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 10.

Model No.:

Serial No.:

Page 3

iii

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked

or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth Blue : Neutral

Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

• The wire which is coloured green-and-yellow must be connected to the terminal in the

plug which is marked by the letter E or by the safety earth symbol

or coloured green or

green-and-yellow.

• The wire which is coloured blue must be connected to the terminal which is marked with

the letter N or coloured black.

• The wire which is coloured brown must be connected to the terminal which is marked with

the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Page 4

The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese and Korean. Carefully read through the operation instructions before operating the projector.

Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch und Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.

Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois, espagnol, italien, néerlandais, portugais, chinois et coréen. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.

Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska och koreanska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.

El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español, italiano, holandés, portugués, chino y coreano. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.

Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano, olandese, portoghese, cinese e coreano. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.

De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans, Nederlands, Portugees, Chinees en Koreaans. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.

O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano, Holandês, Português, Chinês e Coreano. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.

Page 5

Introduction

Before using the projector, please read this operation manual carefully.

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

WARNING: High brightness light source. Do not stare into the beam of light, or view

directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose

this product to rain or moisture.

WARNING: FCC Regulations state that any unauthorized changes or modifications to

this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Introduction

ENGLISH

See bottom of projector.

U.S.A. ONLY

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

Page 6

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 50.

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 (XR40X/XR-30X) / 480,000 (XR-30S) pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

U.S.A. ONLY

Declaration of conformity

SHARP PROJECTOR, MODEL XR-40X/XR-30X/XR-30S This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 TEL: 1-800-BE-SHARP (1-800-237-4277)

U.S.A. ONLY

Authorized representative responsible for the European Union Community Market

SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg

E.U. ONLY

Page 7

Introduction

Useful

Features

Using the Menu Screen

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press MENU/HELP.

• The “Picture” menu screen for the selected input mode is displayed.

Example: “Picture” screen menu for

COMPUTER (RGB) input

Press Q or O and select “Picture” to adjust.

Menu item

Picture Mode

Contrast 0

0 0 0 0

Bright Red Blue

CLR Temp Bright Boost Lamp Setting

Standard

Bright

Reset

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

Adjustment buttons (P/R/O/Q)

ENTER button

RETURN button

•Press RETURN to return to the previous screen when the menu is displayed.

MENU/HELP button

How to Read this Operation Manual

■ The specifications are slightly different, depending on the model. However, you can connect and operate all models in the same manner.

••

• In this operation manual, the illustration and the screen display are simplified for explanation, and

may differ slightly from the actual display.

Info

........Indicates safeguards for using the projector.

For Future Reference

Buttons used in this operation

On-screen display

Button used in this step

Note

.........Indicates additional information for setting up and operating the

projector.

IndexMaintenance Troubleshooting

P. 6 6P. 4 7

PP. 61 and 62

Page 8

Contents

Preparing

Introduction

How to Read this Operation Manual .... 3

Contents ............................................... 4

IMPORTANT SAFEGUARDS ............... 6

How to Access the PDF Operation

Manuals .............................................. 9

Accessories ........................................ 10

Part Names and Functions ................. 11

Inserting the Batteries .......................... 14

Usable Range ...................................... 15

Quick Start

Quick Start .......................................... 16

Using

Basic Operation

Tu r ning the Projector On/Off .............. 25

Turning the Projector on ....................... 25

Turning the Power off (Putting the

Projector into Standby Mode) ........... 25

Image Projection ................................. 26

About the Setup Guide ........................ 26

Adjusting the Projected Image ............ 26

Correcting Trapezoidal Distortion ........ 28

Switching the Input Mode .................... 29

Adjusting the Volume ........................... 29

Displaying the Black Screen and

Turning off the Sound Temporarily .... 29

Resize Mode ......................................... 30

Useful Features

Operating with the Remote Control .... 32

Displaying and Setting

the Break Timer ................................. 32

Displaying the Pointer .......................... 32

Using the Spot Function ...................... 32

Switching the Eco+Quiet Mode ........... 32

Auto Sync (Auto Sync Adjustment) ..... 33

Freezing a Moving Image .................... 33

Selecting the Picture Mode .................. 33

Using the Remote Control as the

Wireless Computer Mouse ................ 34

Menu Items ......................................... 35

Using the Menu Screen ...................... 37

Menu Selections (Adjustments) ........... 37

Picture Adjustment (“Picture” Menu) .. 39

Selecting the Picture Mode .................. 39

Setup

Setting up the Projector ...................... 18

Setting up the Projector ....................... 18

Standard Setup (Front Projection) ....... 18

Ceiling-mount Setup ............................ 18

Projection (PRJ) Mode ......................... 19

Screen Size and Projection Distance .. 20

Connections

Connecting the Projector to

Other Equipment .............................. 21

Controlling the Projector by

a Computer ....................................... 24

Connecting the Power Cord ............... 24

Adjusting the Image ............................. 40

Adjusting the Color Temperature ......... 40

Progressive ........................................... 40

Lamp Setting ........................................ 40

Adjusting the Projected Image

(“SCR - ADJ” Menu) ......................... 41

Setting the Resize Mode ...................... 41

Adjusting the Image Position ............... 41

Keystone Correction ............................ 41

Setting the On-screen Display ............. 42

Selecting the Background Image ........ 42

Selecting the Setup Guide ................... 42

Reversing/Inverting Projected

Images ............................................... 42

Selecting the On-screen Display

Language ........................................... 42

Adjusting the Projector Function

(“PRJ - ADJ” Menu) .......................... 43

Auto Power Off Function ...................... 43

Auto Restart Function .......................... 43

STANDBY Mode ................................... 43

Setting the Confirmation Sound

(System Sound) ................................. 43

Speaker Setting .................................... 43

Audio Input ........................................... 43

Selecting the Transmission Speed

(RS-232C) .......................................... 44

Fan Mode Setting ................................. 44

Checking the Lamp Life Status ........... 44

System Lock Function .......................... 44

Keylock Function .................................. 45

Troubleshooting with the “Help” Menu...

Utilizing the “Help” Menu Functions .... 46

Page 9

Introduction

Reference

Appendix

Maintenance ....................................... 47

Maintenance Indicators ...................... 48

Regarding the Lamp ........................... 50

Lamp ..................................................... 50

Caution Concerning the Lamp ............ 50

Replacing the Lamp ............................. 50

Removing and Installing

the Lamp Unit .................................... 51

Resetting the Lamp Timer .................... 52

Connecting Pin Assignments ............. 53

RS-232C Specifications and

Command Settings ........................... 55

Computer Compatibility Chart ............ 60

Troubleshooting .................................. 61

For SHARP Assistance ...................... 63

Specifications ..................................... 64

Dimensions ......................................... 65

Index ................................................... 66

Page 10

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. Transportation

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

IMPORTANT SAFEGUARDS

10. Ventilation

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.

a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with

a grounding terminal. This plug will only fit into a grounding type power outlet.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.

CAUTION: Please read all of these instructions before you operate this product

and save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.

Page 11

Introduction

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have fallen

into the product.

c. If the product has been exposed to rain or

water.

d. If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e. If the product has been dropped or damaged

in any way.

f. When the product exhibits a distinct change

in performance, this indicates a need for service.

• DLP® and the DLP logo are registered trademarks of Texas Instruments.

• Microsoft

and Windows® are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

• PC/AT is a registered trademark of International Business Machines Corporation in the United States.

• Adobe

Reader® is a trademark of Adobe Systems Incorporated.

• Macintosh

is a registered trademark of Apple Computer, Inc. in the United States and/or

other countries.

• All other company or product names are trademarks or registered trademarks of their respective companies.

• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21. Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Page 12

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Replacing the Lamp” on page 50.

Caution concerning the setup of the projector

■ For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.

Do not set up the projector in places exposed to direct sunlight or bright light.

■ Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projector

■ Place the projector on a level site within the adjustment range (approx. 9 degrees) of the adjustment foot.

When using the projector in high-altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)

■ When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

Warning about placing the projector in a high position

■ When placing the projector in a high position, make certain it is carefully secure to avoid personal injury caused by the projector falling down.

Do not subject the projector to hard impact and/or vibration.

■ Protect the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

■ Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.

Avoid locations with extremes of temperature.

■ The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

■ Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■ Ensure that the intake vent and the exhaust vent are not obstructed.

■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 48 and 49.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

■ After the projector is purchased, a faint smell from the vent may appear when the power is first turned on. This is normal and is not a malfunction. It will disappear after the projector is used for a while.

Page 13

Introduction

Caution regarding usage of the projector

■ If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it.

■ If the power cord is unplugged while the cooling fan is running, some parts of the projector may still be hot. Use caution when handling the projector.

■ Do not carry the projector by holding the lens.

■ When storing the projector, ensure you at-

tach the lens cap to the projector. (See page

11.)

■ Do not expose the projector to direct sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.

Other connected equipment

■ When connecting a computer or other audiovisual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.

■ Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.

Using the projector in other countries

■ The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.

Temperature monitor function

■

If the projector starts to overheat due to setup problems or blockage of the air vents, “ ” and “ ” will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 60-second cooling-off period the projector will enter standby mode. Refer to “Maintenance Indicators” on page 48 for details.

Info

• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.

How to Access the PDF Operation Manuals

PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe

Reader® on your computer (Win-

dows

or Macintosh®).

Please download Adobe® Reader® from the Internet (http://www.adobe.com).

Accessing the PDF Manuals for Windows

(For Macintosh®, skip step 2 ).

Note

• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then specify the desired file using the “File”, “Open” menu.

6 Double click the language (name of the

folder) that you want to view.

7 Double click the pdf file to access the

projector manuals.

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4 Double click the “MANUALS” folder. 5 Double click the model (name of the folder)

that you want to view.

Page 14

Accessories

Remote control

Two R-6 batteries

(“AA” size, UM/SUM-3,

HP-7 or similar)

Power cord*

RGB cable

(10' (3.0 m))

Optional accessories

■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))

■

DIN-D-sub RS-232C adaptor (5 57/64” (15cm))

■ Remote receiver

■ Lamp unit

■ Ceiling-mount bracket

■ Extension tube

AN-C3CP2 AN-A1RS AN-MR2 AN-XR30LP AN-XRCM30 (for U.S.A.)

AN-60KT AN-TK201

AN-TK202

Supplied accessories

For U.S. and

Canada, etc.

(6' (1.8 m))

For Europe, except U.K.

(6' (1.8 m))

For U.K. and

Singapore

(6' (1.8 m))

For Australia, New

Zealand and Oceania

(6' (1.8 m))

(1) (2) (3) (4)

* Use the power cord that corresponds to the wall outlet in your country.

• Operation manual (this manual <TINS-D050WJN1> and CD-ROM <UDSKAA089WJN1>)

Note

• Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.

Lens cap (attached)

Note

• Codes in “< >” are Replacement parts codes.

Page 15

Introduction

25, 48

37, 46

25, 48

Top View

STANDBY/ON button

For turning the power on and putting the projector into standby mode.

Lamp indicator

Temperature warning indicator

Adjustment buttons (P/R/O/Q)

For selecting menu items.

VOL (Volume) buttons (–O/Q+)

For adjusting the speaker sound level.

ENTER button

For setting items selected or adjusted on the menu.

MENU/HELP button

For displaying adjustment and setting screens, and help screen.

Focus ring

For adjusting the focus.

INPUT buttons (P/R)

For switching input mode.

Remote control sensor

HEIGHT ADJUST lever

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

Part Names and Functions

Projector

KEYSTONE button

For entering the Keystone Correction mode.

Intake vent

Power indicator

Zoom ring

For enlarging/ reducing the picture.

Push both sides of the lens cap to attach or remove.

ECO+QUIET button

For lowering the noise of the cooling fan and extending the lamp life.

Front View

Exhaust vent

Speaker

Page 16

21 22

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

Terminals

Rear View

AUDIO 2 input terminal

S-VIDEO input terminal

Te rminal for connecting video equipment with an S-video terminal.

VIDEO input terminal

Te rminal for connecting video equipment.

Rear adjustment foot

Kensington Security Standard connector

AC socket

Connect the supplied power cord.

Using the Kensington Lock

• This projector has a Kensington Security Standard connector for use with a Kensington

MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

AUDIO OUT terminal

Audio output terminal of equipment connected to the audio input terminal.

AUDIO 1 input terminal

COMPUTER/ COMPONENT input terminal

Terminal for computer RGB and component signals.

MONITOR OUT terminal (Output terminal for computer RGB and component signals.)

Terminal for connecting a monitor.

RS-232C terminal

Te rminal for controlling the projector using a computer.

Part Names and Functions (Continued)

DVI-D input terminal

Terminal for DVI digital RGB and digital component signals.

USB terminal

Te rminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.

Page 17

Introduction

34 37

37 46

STANDBY button

For putting the projector into the standby mode.

BREAK TIMER button

For displaying the break time.

COMPUTER, DVI, S-VIDEO, VIDEO buttons

For switching to the respective input modes.

PAGE UP/PAGE DOWN buttons

Same as the [Page Down] and [Page Up] keys on a computer keyboard, when with the USB connection (using a USB cable or the optional remote receiver).

POINTER button

For displaying the pointer.

MOUSE/Adjustment buttons (P/R/O/Q)

• For moving the

computer cursor when with the USB connection (using a USB cable or the optional remote receiver).

• For selecting and adjusting menu

items.

L-CLICK button

For the Left click when with the USB connection (using a USB cable or the optional remote receiver).

KEYSTONE button

For entering the Keystone Correction mode.

AUTO SYNC button

For automatically adjusting images when connected to a computer.

ECO+QUIET button

For lowering the noise of the cooling fan and extending the lamp life.

AV MUTE button

For temporarily displaying a black screen and turning off the sound.

FREEZE button

For freezing images.

VOL +/– (Volume) buttons

For adjusting the speaker sound level.

ON button

For turning the power on.

SPOT button

For displaying the spotlight.

R-CLICK/RETURN button

• For the Right click when with the USB connection (using a USB cable or the optional remote receiver).

• For returning to the previous menu screen during menu operations.

ENTER button

For setting items selected or adjusted on the menu.

MENU/HELP button

For displaying adjustment and setting screens, and help screen.

PICTURE MODE button

For selecting the appropriate picture.

RESIZE button

For switching the picture size (NORMAL, BORDER, etc.).

Page 18

• Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.

• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.

• Do not mix new and old batteries. This may shorten the life of new batteries or may cause old batteries to leak.

• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them using a cloth.

• The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.

• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.

Part Names and Functions (Continued)

Inserting the Batteries

Insert the lower tab of the cover into the opening, and lower the cover until it clicks in place.

Insert the batteries.

• Insert the batteries making sure the polarities correctly match

the m and n marks inside the battery compartment.

Pull down the tab on the cover and remove the cover towards the direction of the arrow.

Caution

Page 19

Introduction

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.

Note

• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.

When using the remote control

• Ensure that you do not drop it or expose it to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp. In this case, move the projector away from the fluorescent lamp.

Remote control sensor

Remote control signal transmitters

Remote control

23n (7 m)

30°

Page 20

Quick Start

This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.

When connecting equipment other than a computer, see pages 22 and 23.

3. Remove the lens cap and turn the projector on

2. Connect the projector to the computer and plug the power cord into the AC socket of the projector

On the projector On the remote control

KEYSTONE button

INPUT buttons

STANDBY/ON button

HEIGHT ADJUST lever

Focus ring

STANDBY button

_PP. 21, 24

_P. 25

ENTER button

KEYSTONE button

ON button

COMPUTER button

1. Place the projector facing a wall or a screen

_P. 18

Adjustment buttons (P/R/O/Q)

Zoom ring

Page 21

Quick Start

4. Adjust the projected image with the Setup Guide

_PP. 26, 27

1 After the projector turns on, the Setup Guide appears.

(When “Setup Guide” is set to “On”. See page 42.)

2 Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle).

3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup

Guide.

Correcting trapezoidal distortion using Keystone Correction.

5. Correct trapezoidal distortion

8. Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confirmation message is displayed to put the projector into standby mode.

On-screen display

On the

projector

On the remote

control

_P. 25

On the projector

On the remote control

Shrinks

upper side.

Shrinks

lower side.

_P. 28

Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.

6. Select the INPUT mode

• When you press INPUT on the projector, the INPUT list appears.

Press '/" to switch the INPUT mode.

On the

projector

On the remote

control

INPUT list

_P. 29

INPUT

COMPUTER

DVI-D Computer

DVI-D Video

On-screen display (RGB)

RGB 1024 × 768

COMPUTER

7. Turn the computer on

Page 22

Ceiling-mount Setup

■ It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount bracket (sold separately).

Setting up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 28.)

Side View

Standard Setup (Front Projection)

■ Place the projector at the required distance from the screen according to the desired picture size. (See page 20.)

Example of standard setup

Screen

Lens center

• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.

Note

Page 23

Setup

300"

200"

100"

84" 60"

36'10

(11.2 m)

24'7

"–

28'4

(7.5 m

–

8.6 m)

12'3

"–

14'2

(3.7 m

–

4.3 m)

10'4

"–

11'11

(3.1 m

–

3.6 m)

7'4

"–

8'6

(2.2 m – 2.6 m)

240"×180"

160"

120"

80"

60"

67"

50"

48"

36"

Projection (PRJ) Mode

The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu. See page 42.)

■ Ta ble mounted, front projection

[Menu item ➞ “Front”]

■ Ceiling mounted, front projection

[Menu item ➞ “Ceiling + Front”]

■ Ta ble mounted, rear projection

(with a translucent screen)

[Menu item ➞ “Rear”]

■ Ceiling mounted, rear projection

(with a translucent screen)

[Menu item ➞ “Ceiling + Rear”]

Indication of the Projection Image Size and Projection Distance

Picture Size

Projection Distance

Example: NORMAL Mode (4:3)

Page 24

Setting up the Projector (Continued)

300 (762 cm)

270 (686 cm)

250 (635 cm)

200 (508 cm)

150 (381 cm)

100 (254 cm)

84 (213 cm)

72 (183 cm)

60 (152 cm)

40 (102 cm)

610 cm (240)

549 cm (216)

508 cm (200)

406 cm (160)

305 cm (120)

203 cm (80)

171 cm (67)

146 cm (58)

122 cm (48)

81 cm (32)

19 cm

17 cm

16 cm

13 cm

10 cm

6 cm

5 cm

4 cm

3 cm

/16)

/64)

/32)

/64)

/16)

/64)

457 cm (180)

411 cm (162)

381 cm (150)

305 cm (120)

229 cm (90)

152 cm (60)

128 cm (50)

110 cm (43)

91 cm (36)

61 cm (24)

11.2 m (36 10)

10.1 m (33 2)

9.4 m (30 9)

7.5 m (24 7)

5.6 m (18 5)

3.7 m (12 3)

3.1 m (10 4)

2.7 m (8 10)

2.2 m (7 4)

1.5 m (4 11)

—

11.7 m (38 4)

10.8 m (35 5)

8.6 m (28 4)

6.5 m (21 3)

4.3 m (14 2)

3.6 m (11 11)

3.1 m (10 3)

2.6 m (8 6)

1.7 m (5 8)

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.0408

L2 (m) = 0.0471

H (cm) = 0.27727

S (cm) = ±0.20754

Screen Size and Projection Distance

• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the bottom of the image [H]”.

• Allow a margin of error in the values in the diagrams above.

NORMAL Mode (4:3)

Picture (Screen) size

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.03745

L2 (m) = 0.04323

H (cm) = 0.064

: Picture size (diag.) (in/cm) L: Projection distance (m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the lens center to the bottom of the image (cm/in)

Projection distance [L]

Diag. [χ] Width Height

Minimum [L1] Maximum [L2]

STRETCH Mode (16:9)

250 (635 cm)

225 (572 cm)

200 (508 cm)

150 (381 cm)

133 (338 cm)

106 (269 cm)

100 (254 cm)

92 (234 cm)

84 (213 cm)

72 (183 cm)

60 (152 cm)

40 (102 cm)

553 cm (218)

498 cm (196)

443 cm (174)

332 cm (131)

294 cm (116)

235 cm (92)

221 cm (87)

204 cm (80)

186 cm (73)

159 cm (63)

133 cm (52)

89 cm (35)

69 cm

62 cm

55 cm

42 cm

37 cm

29 cm

28 cm

26 cm

23 cm

20 cm

17 cm

11 cm

(27

/64)

(24

/16)

(21

/64)

(16

/8)

(14

/64)

(11

/64)

(10

/64)

(10

/64)

52 cm

47 cm

42 cm

31 cm

28 cm

22 cm

21 cm

19 cm

17 cm

15 cm

12 cm

 8 cm

(20

/64)

(18

/64)

(16

/32)

(12

/4)

(10

/8)

(8

/32)

(8

/64)

(7

/64)

(6

/64)

(5

/64)

(4

/32)

(3

/64)

311 cm (123)

280 cm (110)

249 cm (98)

187 cm (74)

166 cm (65)

132 cm (52)

125 cm (49)

115 cm (45)

105 cm (41)

90 cm (35)

75 cm (29)

50 cm (20)

10.2 m (33 6)

9.2 m (30 1)

8.2 m (26 9)

6.1 m (20 1)

5.4 m (17 10)

4.3 m (14 2)

4.1 m (13 5)

3.8 m (12 4)

3.4 m (11 3)

2.9 m (9 8)

2.4 m (8)

1.6 m (5 4)

11.8 m (38 8)

10.6 m (34 9)

9.4 m (30 11)

7.1 m (23 2)

6.3 m (20 7)

5.0 m (16 5)

4.7 m (15 5)

4.3 m (14 3)

4.0 m (13)

3.4 m (11 2)

2.8 m (9 3)

1.9 m (6 2)

Note

Distance from the lens center

to the bottom of the image [H]

Picture (Screen) size

Projection distance [L]

Diag. [χ] Width Height

Minimum [L1] Maximum [L2]

Distance from the lens center to

the bottom of the image [H]

Adjustable range of

image position [S]

[Feet/inches]

L1 (ft) = 0.03745χ / 0.3048 L2 (ft) = 0.04323χ / 0.3048 H (in) = 0.064χ / 2.54

[Feet/inches]

L1 (ft) = 0.0408χ / 0.3048 L2 (ft) = 0.0471χ / 0.3048 H (in) = 0.27727χ / 2.54 S (in) = ±0.20754χ / 2.54

Page 25

Connections

Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.

IMPORTANT:

Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.

•

For more details of connection and cables, refer to the operation manual of the connecting equipment.

•You may need other cables or connectors not listed below.

Connecting the Projector to Other Equipment

Terminals on the Projector

COMPUTER/ COMPONENT

DVI-D

Equipment

Computer

DVI digital

output

terminal

Cable

DVI Digital cable (commercially available)

Terminal on

connected equipment

Terminal on the

projector

RGB

output

terminal

RGB cable (supplied)

• See page 60 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-

tor. Use with computer signals other than those listed may cause some of the functions to not work.

•A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-

est Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless the

computer’s external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the specific instructions in your computer's

operation manual to enable your computer’s external output port.

Note

Page 26

Connecting the Projector to Other Equipment (Continued)

S-VIDEO

VIDEO

COMPUTER/ COMPONENT

Equipment

Video equipment

Camera/Video game

Cable

S-video cable (commercially available)

Video cable (commercially available)

Cables for a camera or a video game

Cables for a camera or a video game/3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)

Terminal on

connected equipment

Terminal on the

projector

S-video

output

terminal

Video

output

terminal

S-video

output

terminal

Video

output

terminal

Component

video

output

terminal

RCA adaptor plug (commercially available)

S-VIDEO

VIDEO

3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)

COMPUTER/ COMPONENT

Component

video

output

terminal

HDMI to DVI cable (commercially available)

DVI-D

HDMI

output

terminal

DVI digital

output

terminal

DVI Digital cable (commercially available)

• While the projector is connected to video equipment that has an HDMI output terminal, only the

video signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)

• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission

may not work property. (The HDMI specification does not support all connections to video equipment that has HDMI digital output terminal using HDMI to DVI digital cable.)

• For details on compatibility for connection, see support information on DVI connection provided by

the video equipment manufacturer.

• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a

commercially available cable that fits in the projector terminal you want to connect.

• The projector does not support RGBC signals via the Euro-scart.

Note

Page 27

Connections

Note

• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm

stereo audio cable.

•You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 43.)

• RGB signals and Component signals can be output to the monitor.

Equipment Cable

Terminal on

connected equipment

Terminal on the

projector

Audio

output

terminal

Monitor

Amplifier

MONITOR OUT

AUDIO OUT

RGB

input

terminal

RGB cable (supplied or commercially available)

AUDIO 1

Audio equipment

ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp service part QCNWGA038WJPZ)

ø3.5 mm

audio output

terminal

ø3.5 mm

audio input

terminal

RCA audio

output

terminal

RCA audio

input

terminal

ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp service part QCNWGA038WJPZ)

ø3.5 mm stereo minijack to RCA audio cable (commercially available)

RCA audio cable (commercially available)

Cables for a camera or a video game

AUDIO 2

Page 28

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS232C adaptor (optional, AN-A1RS) and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 55 for details.

When connecting to a computer using an RS-232C serial control cable and a DIND-sub RS-232C adaptor

To RS-232C terminal

DIN-D-sub RS-232C adaptor (optional, AN-A1RS)

RS-232C serial control cable (cross type, commercially available)

Note

• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the

operation manual of the computer for details.

• See pages 53 and 54 for connection of an RS-232C serial control cable.

Info

• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector.

• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.

Connecting the Power Cord

Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet.

AC socket

Computer

Supplied

accessory

To AC outlet

To RS-232C terminal

Power cord (supplied)

Page 29

Basic

Operation

Turning the Projector On/Off

On-screen display (confirmation message)

• When “Auto Restart” is set to “On”: If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 43.)

• English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 42.

Info

Turning the Projector on

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 24.)

Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control.

• The power indicator illuminates green.

• After the lamp indicator illuminates, the projec-

tor is ready to start operation.

Note

• About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on. Blinking in green: The lamp is warming up. Red: The lamp is shut down abnormally

or the lamp should be replaced.

• When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

• If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start projection.

•

When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 44 for details.

Tur ning the Power off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then

press that button again while the confirmation message is displayed, to put the projector into standby mode.

• The projector cannot be turned on while cool-

ing.

STANDBY/ON button

Lamp indicator

Power indicator

STANDBY button

ON button

• Direct Power Off function: You can unplug the power cord from the AC outlet even if the cooling fan is still running.

Info

Page 30

About the Setup Guide

After turning on the projector, the Setup Guide screen appears to assist you with projector setup.

Press ENTER to exit the Setup Guide screen.

Guidance items

1 FOCUS 2 HEIGHT ADJUST 3 ZOOM

1 Adjusting the Focus

You can adjust the focus with the focus ring on the projector.

Image Projection

Rotate the focus ring to adjust the focus while watching the projected image.

Setup Guide screen

• The Setup Guide screen automatically highlights the items in the following order:

1 FOCUS

3 ZOOM4 ENTER

2 HEIGHT ADJUST

However, you can adjust the focus, height (angle), or zoom regardless of the highlighted item.

• If you do not want to display the Setup Guide for the next time, set “Menu” - “SCR - ADJ” “Setup Guide” to “Off”. (See page 42.)

Note

Adjusting the Projected Image

2 Adjusting the Picture Size

You can adjust the picture size using the zoom ring on the projector.

Rotate the zoom ring to enlarge or shrink the picture size.

STANDBY/ON button

ENTER button

Focus ring

Zoom ring

Page 31

Basic

Operation

3 Adjusting the Height

The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector.

When the screen is above the projector, the projection image can be made higher by adjusting the projector.

• Do not apply too much pressure on the projector when the front adjustment foot comes out.

• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector.

•

Hold the projector firmly while lifting or carrying.

• Do not hold by the lens area.

Use the rear adjustment foot to make the projector level.

• The projector is adjustable ±2 degree from the standard position.

Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted.

• The angle of projection is adjustable up to approx. 9 degrees from the surface on which the projector is placed.

Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever.

Info

• When adjusting the height of the projector, trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the distortion. (See pages 28 and 41.)

Note

Rear adjustment foot

HEIGHT ADJUST lever

Make small adjustments.

Page 32

0KEYSTONE

ADJUST END

Correcting Trapezoidal Distortion

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.

• The Keystone Correction can be adjusted up to an angle of approximately ±20 degrees and the screen can also be set up to an angle of approximately ±20 degrees (when the resize mode is set to “NORMAL” (see page 30)).

Note

Press KEYSTONE.

• The on-screen display of the Keystone Correction mode will disappear.

•You can also use KEYSTONE on the pro- jector.

Press P/Q or O/R to adjust the Keystone Correction.

•You can also adjust the Keystone Correction using the adjustment buttons on the projector.

Press KEYSTONE to enter the Keystone Correction mode.

•You can also display the on-screen display of the Keystone Correction mode with KEYSTONE on the projector.

•To return to the default setting, press RETURN while the on-screen display of the Keystone Correction mode is on the screen.

Note

On-screen display (Keystone Correction mode)

Shrinks upper side. (Move the slide bar in the + direction.)

Shrinks lower side. (Move the slide bar in the - direction.)

Image Projection (Continued)

• While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged.

Info

KEYSTONE button

Adjustment buttons (P/R/O/Q)

RETURN button

Page 33

Basic

Operation

Displaying the Black Screen and Turning off the Sound Temporarily

Adjusting the Volume

Switching the Input Mode

Press COMPUTER, DVI, S-VIDEO or VIDEO on the remote control to select

the input mode.

• When you press INPUT on the projector or DVI on the remote control, the INPUT list appears. Press P/R to switch the INPUT mode.

Select the appropriate input mode for the connected equipment.

Press VOL +/– on the remote control or –O/Q+ on the projector to adjust the vol-

ume.

•Pressing VOL–/–O will lower the volume.

•Pressing VOL+/Q+ will raise the volume.

• When the projector is connected to external equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector’s volume to the lowest level when turning the projector on/ off or when changing the input signal.

• When you do not want to output the sound from the projector’s speaker while the projector is connected to external equipment, set “Speaker” in “PRJ-ADJ” menu to “Off”. (See page 43.)

Press AV MUTE on the remote control to temporarily display a black screen and turn off the sound.

•Pressing AV MUTE again will turn the projected image back on.

On-screen display

Note

On-screen display

VOL +/– (Volume) buttons

COMPUTER, DVI, S-VIDEO, VIDEO buttons

AV MUTE button

Page 34

Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.

Press RESIZE.

• See page 41 for setting on menu screen.

Computer

RESIZE button

* Mode for projecting an image with the original aspect ratio without cutting any portions.

: Cutout area on which images cannot be projected.

Input Signal

NORMAL

Output screen image

Computer

Image type BORDER

STRETCH

SXGA

(1280K1024)

WXGA

4:3 aspect ratio

5:4 aspect ratio

16:9 aspect ratio

Resolution lower than

XGA

Resolution

higher than

XGA

XR-30S

XR-40X/30X

Resolution lower than

SVGA

Resolution

higher

than

SVGA

Other aspect ratios

4:3 aspect ratio

NORMAL BORDER

STRETCH

SVGA (800 K 600)

XR-40X/30X XR-30S XR-40X/30X XR-30S XR-40X/30X XR-30S

XGA (1024 K 768)

SXGA (1280 K 960)

SXGA L (1400

1050)

SXGA (1280

1024)

WXGA (1280 K 768)

1024

768 800

600J768

576 600

450

1024

576 800

450

Main resolution

Page 35

Basic

Operation

VIDEO

• “STRETCH” is fixed when 540P, 720P, 1035I or 1080I signals are entered.

Input Signal

DVD / Video Image type

Output screen image

NORMAL

BORDER

STRETCH

480I, 480P, 576I,

576P, NTSC, PAL,

SECAM

540P, 720P, 1035I,

1080I

4:3 aspect ratio

Letter box

Squeezed 16:9 image

Squeezed 4:3 image

16:9 aspect ratio

6:9 aspect ratio

(4:3 aspect ratio in 16:9)

* Mode for projecting an image with the original aspect ratio without cutting any portions.

: Cutout area on which images cannot be projected. : Area on which the image is not included in the original signals.

Page 36

Operating with the Remote Control

Displaying and Setting the Break Timer

Press BREAK TIMER.

• The timer starts to count down from 5 minutes.

Press P /R /O /Q to adjust the length of the break time.

• Increases with P or Q

5 minutes s 6 minutes s 60 minutes

• Shortens with O or R

4 minutes s 3 minutes s1 minute

• The break time can be set in units of one minute (up to 60 minutes).

On-screen display

Canceling the break timer display function

Press BREAK TIMER.

•Break Timer does not function while the projector is operating the “Auto Sync”, “FREEZE” or “AV MUTE” functions.

Note

POINTER button

ECO+QUIET button

Adjustment buttons (P/R/O/Q)

BREAK TIMER button

SPOT button

Switching the Eco+Quiet Mode

Press ECO+QUIET on the remote control or on the projector to switch the Eco+Quiet mode between on and off.

• When the Eco+Quiet Mode is set to “ON”, the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend.

Press POINTER and press P/R/ O/Q on the remote control to move

the pointer.

Displaying the Pointer

Press SPOT and press P /R/O/Q on the remote control to move the spot area.

Using the Spot Function

Press POINTER again.

• The pointer will disappear.

Press SPOT again.

• The spot area will disappear.

• Refer to “Lamp Setting” on page 40 for details of the Eco+Quiet mode.

Note

Page 37

Useful

Features

Auto Sync (Auto Sync Adjustment)

Freezing a Moving Image

• When the optimum image cannot be achieved with Auto Sync adjustment, use the help menu for manual adjustments. (See page 46.)

Auto Sync function works when detecting input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function.

Press FREEZE.

• The projected image is frozen.

Press FREEZE again to return to the moving image from the currently connected device.

Note

Selecting the Picture Mode

Press PICTURE MODE.

• When pressing PICTURE MODE, the picture mode changes in the following order:

STANDARD PRESENTATION MOVIE GAME sRGB

You can select the appropriate picture mode for the projected image, such as movie or video game.

• See page 39 for details on the picture mode.

Note

* “sRGB” is displayed only when RGB signal is

input.

AUTO SYNC button

FREEZE button

PICTURE MODE button

Page 38

Using the Remote Control as the Wireless Computer Mouse

When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse.

If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver.

Connecting with a USB cable

emote receiver

(optional, AN-MR2)

To USB terminal

USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ)

To USB terminal

Computer

MOUSE/Adjustment buttons ('/"/\/|)

R-CLICK button

L-CLICK button

PAGE UP/ PAGE DOWN buttons

The mouse pointer can be operated in the following way after it is connected.

■ When moving the cursor

Press MOUSE/Adjustment buttons (P/R/O/Q).

■ When left-clicking

Press L-CLICK.

■ When right-clicking

Press R-CLICK.

■

When your computer supports only a

one-click mouse (such as Macintosh)

Press L-CLICK or R-CLICK. L-CLICK and R-CLICK have common function.

■ When using [Page Up] or [Page Down]

• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function does not work with the following operation systems that do not support USB.

• Versions earlier than Windows® 95

• Versions earlier than Windows® NT4.0

• Versions earlier than Mac OS® 8.5

•You cannot use this function when displaying the menu screen.

• Confirm that the computer recognizes the USB connection.

Note

Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE DOWN.

Operating with the Remote Control (Continued)

Page 39

Useful

Features

The following shows the items that can be set in the projector.

Menu Items

“Screen adjustment (SCR-ADJ)” menu

COMPUTER (Component), DVI (Component), S-VIDEO, VIDEO input

“Picture” menu

Picture Mode

Contrast 0

0 0 0 0

Bright Red Blue

CLR Temp Bright Boost Lamp Setting

Standard

Bright

Reset

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Picture Mode

Contrast 0

0 0 0

Bright Color Tint

0 0

Sharp

CLR Temp Bright Boost Progressive 3D Progressive

Standard

Reset

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Lamp Setting Bright

Resize Image Shift 0

Keystone OSD Display Background Setup Guide PRJ Mode Language

Front English

Logo

Border

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Main menu Sub menu

Picture

Page 39

+30-30

Contrast

+30-30

2-2

+30-30

Tint

Color

Sharp

Bright

Red

Blue

*2*3

Progressive

Lamp Setting

Reset

2D Progressive 3D Progressive Film Mode

Bright Eco + Quiet

CLR Temp

Bright Boost [0/1/2]

Page 39

Page 40

Standard Presentation Movie Game sRGB*1

Picture Mode

Main menu Sub menu

SCR - ADJ

Page 41

Language

Image Shift

Resize

Page 41

Page 42

Keystone

OSD Display [On/Off]

Background

Setup Guide

[On/Off]

PRJ Mode

Normal Border Stretch

Logo Blue None

Front Ceiling + Front Rear Ceiling + Rear

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Türkçe

-96 +96

-75 +75

-168 +168

-124 +124*5*6

*5 *6

*1 Items when inputting RGB signal through COMPUTER or

DVI.

*2 Items when inputting component signal through COM-

PUTER or DVI, or when selecting S-VIDEO or VIDEO.

*3 “Tone” will appear on the menu screen only when PAL or

SECAM signals are input (including when forcibly changed to those input signals). There is basically no need to adjust “Tone”, but you can adjust the picture tone with this adjustment when inputting PAL or SECAM signals.

*4 Items when inputting component signal through

COMPUTER, or when selecting S-VIDEO or VIDEO. *5 Adjustment range for XR-40X/XR-30X. *6 Adjustment range for XR-30S.

COMPUTER (RGB), DVI (RGB) input

Page 40

“Projector adjustment (PRJ-ADJ)” menu

Auto Power Off

System Sound

System Lock

On Auto Restart On STANDBY Mode Standard

0 min0Lamp Timer(Life) 100%

Picture SCR - ADJ PRJ - ADJ Help

SEL./ADJ. ENTER END

Speaker On Audio Input Audio 1 RS-232C 9600bps Fan Mode Normal

Disable

There is no picture or audio Vertical stripes or flickering image appear Data image is not centered Color is faded or poor Picture is dark The image is distorted

Reset all adjustments to default settings

SEL. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Main menu Sub menu

PRJ - ADJ

Page 43

STANDBY Mode

System Sound [On/Off]

Speaker [On/Off]

System Lock [Enable/Disable]

Lamp Timer(Life)

Page 43

Auto Restart [On/Off]

Page 43

Auto Power Off [On/Off]

Page 43

Page 44

Fan Mode

Page 44

Normal High

RS-232C

Page 44

9600bps 115200bps

Audio Input

Page 43

Audio 1 Audio 2

Standard Eco

“Help” menu

The items you can set with the “Help” menu

“Help” menu n Page 46

•Vertical stripes or flickering image appear Auto Sync Clock Phase

• Data image is not centered Auto Sync H-Pos V-Pos

• Color is faded or poor COMPUTER/COMPONENT or DVI input

Signal type: Auto/RGB/Component

S-VIDEO or VIDEO input

Video System: Auto/PAL/SECAM/

NTSC3.58/NTSC4.43/ PAL-M/PAL-N/PAL-60

DVI input

Dynamic range: Auto/Standard/Enhanced

* The selectable items vary depending on the in-

put signal and the selected input mode.

Menu Items (Continued)

Page 41

Useful

Features

Using the Menu Screen

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press MENU/HELP.

• The “Picture” menu screen for the selected input mode is displayed.

Example: “Picture” screen menu for

COMPUTER (RGB) input

Press Q or O and select “Picture” to adjust.

Menu item

Picture Mode

Contrast 0

0 0 0 0

Bright Red Blue

CLR Temp Bright Boost Lamp Setting

Standard

Bright

Reset

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

Adjustment buttons (P/R/O/Q)

ENTER button

RETURN button

•Press RETURN to return to the previous screen when the menu is displayed.

MENU/HELP button

Page 42

Using the Menu Screen (Continued)

Press P or R and select “Bright” to adjust.

• The selected item is highlighted.

•Press ENTER again to return to the previous screen.

Press O or Q to adjust the item selected.

• The adjustment is stored.

Press MENU/HELP.

• The menu screen will disappear.

0Bright

Picture

SEL./ADJ. Rtn. Menu END

15Bright

Picture Mode

Contrast 0

0 0 0

Red Blue

CLR Temp Bright Boost Lamp Setting

Standard

Bright

Reset

SEL./ADJ. Single ADJ END

Picture SCR - ADJ PRJ - ADJ Help

Note

Contrast 0

0 0

Bright

Red Blue CLR Temp Bright Boost

Picture Mode

Lamp Setting

Standard

Bright

Reset

SEL./ADJ. Single ADJ END

Picture SCR - ADJ PRJ - ADJ Help

Resize Image Shift 0

Keystone OSD Display On

Border

Picture SCR - ADJ PRJ - ADJ Help

Items to be adjusted

• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”, “FREEZE”, or “AV MUTE” functions.

Note

To adjust the projected image while watching it

Press ENTER.

• The selected item (e.g. “Bright”) is displayed by itself at the bottom of the screen.

• When pressing P or R, the following item (“Red” after “Bright”) will be displayed.

The item displayed by itself

Press ENTER.

Page 43

Useful

Features

Picture Adjustment (“Picture” Menu)

Standard

Presentation

Movie

Game

*sRGB

Q Example: “Picture” screen menu for

COMPUTER (RGB) input

Q Example: “Picture” screen menu for

S-VIDEO input

Picture Mode

Contrast 0

0 0 0 0

Bright Red Blue

CLR Temp Bright Boost Lamp Setting

Standard

Bright

Reset

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

For standard image

Brightens portions of image for more enhanced presentations.

Gives natural tint to the projected image.

Gives sharpness to the projected image.

For high fidelity reproduction of images from a computer.

Picture Mode

Contrast 0

0 0 0

Bright Color Tint

0 0

Sharp

CLR Temp Bright Boost Progressive 3D Progressive

Standard

Reset

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

Lamp Setting Bright

Menu operation n Page 37

•

You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.)

• *sRGB is an international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are displayed in a natural tint based on an original image, when “sRGB” is selected. For additional information about the sRGB function, visit “http://www.srgb.com/”. You cannot set the items, “Red”, “Blue”, “CLR Temp”, “Bright Boost”, when “sRGB” is selected.

Note

1 1

1 Selecting the Picture Mode

• When “sRGB” is selected, the projected image may become dark, but this does not indicate a malfunction.

Info

• “sRGB” is displayed only when RGB signal is input.

•You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.

–1

–

Bright

Eco + Quiet

Bright

The default settings of each item when selecting Picture Mode

–

CLR Temp

Selectable

items

Description

Bright Boost Lamp Setting

Page 44

4 Progressive

• In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the three-two pull down enhancement will be enabled automatically when the film source has been entered.

• When the image is blurred or noisy, switch to the optimal mode.

• When using progressive inputs, inputs are directly displayed so that 2D Progressive, 3D Progressive and Film Mode cannot be selected.

* The film source is a digital video recording with the

original encoded as is at 24 frames/second. The projector can convert this film source to progressive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.

Selectable

items

2D Progressive

3D Progressive

Film Mode

Description

Useful to display fast-moving images such as sports.

Useful to display relatively slowmoving images such as drama and documentary more clearly.

Reproduces the image of film source* clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhancement to progressive mode images.

Note

5 Lamp Setting

• In the Eco + Quiet mode, the fan sound and power consumption are lower than those in the Bright mode. (Projection brightness decreases as shown in the chart.) The lamp life will be approximately 3,000 hours (approximately 2,000 hours in the Bright mode).

Note

Picture Adjustment (“Picture” Menu) (Continued)

2 Adjusting the Image

*1 Not adjustable/selectable when selecting “sRGB”. *2 Not displayed in the RGB input mode. *3 “Tone” will appear on the menu screen only when

PAL or SECAM signals are input (including when forcibly changed to those input signals). There is basically no need to adjust “Tone”, but you can adjust the picture tone with this adjustment when inputting PAL or SECAM signals .

Q button

For more contrast.

For more brightness.

For stronger red.

For stronger blue.

For more color intensity.

For making skin tones greenish.

For more sharpness.

For more vividness.

Adjustment

items

Contrast

Bright

Red*

Blue*

Color*

Tint*2 *

Sharp*

Bright Boost*

O button

For less contrast.

For less brightness.

For weaker red.

For weaker blue.

For less color intensity.

For making skin tones purplish.

For less sharpness.

For high fidelity color reproduction.

Note

• “Bright Boost” and “CLR Temp” cannot be set when “sRGB” is selected.

•To reset all adjustment items, select “Reset” and press ENTER.

3 Adjusting the Color

Temperature

•Values on “CLR Temp” are only for general standard purposes.

Note

Selectable

items

–2 –1

0 1 2

Description

For lower color temperature for warmer, reddish incandescent-like images.

For higher color temperature for cooler, bluish, fluorescent-like images.

Menu operation n Page 37

P R

Selectable

items

Eco + Quiet

Bright

Brightness and Power consumption

100%

Approx. 80%

Page 45

Useful

Features

Adjusting the Projected Image (“SCR - ADJ” Menu)

Resize Image Shift 0

Keystone OSD Display Background Setup Guide PRJ Mode Language

Front English

Logo

Border

SEL./ADJ. ENTER END

Picture SCR - ADJ PRJ - ADJ Help

1 Setting the Resize Mode

• For details of the Resize mode, see pages 30 and 31.

•You can also press RESIZE on the remote con- trol to set the resize mode. (See page 30.)

Note

2 Adjusting the Image

Position

You can move the projected image vertically.

Q button

•You cannot set this item when “Resize” is set to “Normal”.

Note

O button

Menu operation n Page 37

3 Keystone Correction

Select “Keystone” on the “SCR-ADJ” menu and adjust with the slide bar.

See page 28 for details of Keystone Correction.

O buttonQ button

• The Keystone Correction can be adjusted up to an angle of approximately ±20 degrees (when “Resize” is set to “Normal”).

Note

Page 46

The projector can switch the on-screen display language among 15 languages.

Selectable items

Front

Ceiling + Front

Rear

Ceiling + Rear

Description

Normal image (Projected from the front of the screen)

Inverted image (Projected from the front of the screen with an inverted projector)

Reversed image (Projected from the rear of the screen or with a mirror)

Reversed and inverted image (Projected with a mirror)

6 Selecting the Setup

Guide

Selecting the On-screen Display Language

Selectable items

Off

Description

Displaying the Setup Guide when turning the projector on.

Not displaying the Setup Guide.

7 Reversing/Inverting

Projected Images

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Türkçe

Adjusting the Projected Image (“SCR - ADJ” Menu) (Continued)

4 Setting the On-screen

Display

Menu operation n Page 37

Selectable

items

Off

Description

All on-screen displays are displayed.

INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/RESIZE/PICTURE MODE/ “An invalid button has been pressed.” are not displayed.

Selecting the Background Image

Selectable items

Logo

Blue

None

Description

Sharp logo screen

Blue screen

—

See page 19 for details of Projection (PRJ) Mode.

Page 47

Useful

Features

Adjusting the Projector Function (“PRJ - ADJ” Menu)

Auto Power Off

System Sound

System Lock

On Auto Restart On STANDBY Mode Standard

0 min0Lamp Timer(Life) 100%

Picture SCR - ADJ PRJ - ADJ Help

SEL./ADJ. ENTER END

Speaker On Audio Input Audio 1 RS-232C 9600 bps Fan Mode Normal

Disable

Menu operation n Page 37

• When the Auto Power Off function is set to “On”, 5 minutes before the projector enters standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.

Selectable

items

Off

Description

When no input signal is detected for more than 15 minutes, the projector will automatically enter standby mode.

The Auto Power Off function will be disabled.

Note

Auto Power Off Function

5 Speaker Setting

Setting the Confirmation Sound (System Sound)

Selectable

items

Off

Description

A confirmation sound is made when the projector turns on/off.

No confirmation sound is made.

When set to “Eco”, power consumption is reduced in standby mode.

3 3

3 STANDBY Mode

Selectable

items

Off

Description

The audio signal is output from the internal speaker.

The audio signal is not output from the internal speaker.

Monitor Output

This function allows you to select an appropriate combination of audio input terminals for each input mode.

6 6

6 Audio Input

Selectable

items

Audio 1

Audio 2

Description

The AUDIO 1 input terminal is used as an audio input terminal.

The AUDIO 2 input terminal is used as an audio input terminal.

Selectable

items

Eco

Standard

Description

The monitor output and RS-232C functions are switched off in standby mode.

The monitor output and RS-232C functions are activated even if the projector is in standby mode.

2 Auto Restart Function

Selectable

items

Off

Description

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on.

The projector does not turn on automatically when the power cord is plugged into the AC outlet or the breaker switch is turned on.

Page 48

Info

This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest you record

the keycode in a safe place where only authorized users have access.

•

If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 63). Even if the product warranty is valid, the keycode reset will incur a charge.

Press the 4 buttons on the remote control or on the projector to enter the preset keycode in “Old Code”.

• When setting the keycode for the first

time, press R on the projector for four times.

Setting the System Lock

PRJ - ADJ

Old Code

New Code Reconfirm

––––

–––– ––––

• If you input a wrong keycode, the cursor returns to the first point of the “Old Code”.

• The preset keycode is 4 R buttons on the projector. When you press the R but- ton four times, the keycord input screen disappears.

Note

9 System Lock Function

Adjusting the Projector Function (“PRJ - ADJ” Menu) (Continued)

8 Fan Mode Setting

Menu operation n Page 37

This function changes the fan rotation speed.

Selectable

items

Normal

High

Description

Suitable for normal environments.

Select this when using the projector at altitudes of approximately 1,500 meters (4,900 feet) or more.

Selecting the Transmission Speed (RS-232C)

Make sure that both the projector and computer are set for the same baud rate.

Selectable

items

9600bps

115200bps

Description

Transmission speed is slow.

Transmission speed is rapid.

P R

0 Checking the Lamp Life

Status

You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).

• It is recommended that the lamp be changed when the remaining lamp life becomes 5%.

• The lamp life may vary depending on the usage condition.

Lamp usage condition

Operated exclusively with Lamp Setting set to “Eco +Quiet”

Operated exclusively with Lamp Setting set to “Bright”

100%

Approx. 3,000 hours

Approx. 2,000 hours

Approx. 150 hours

Approx. 100 hours

Remaining lamp life

Note

“Life”

a Setting/Changing the keycode

When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.

Select “System Lock”, then press ENTER or Q.

Select “Next”, then press ENTER.

• The screen for entering the keycode

appears.

Page 49

Useful

Features

Note

Input screen for keycode

To cancel the keycode that you have already set

•Press R on the projector for four times in steps

3 and 4 above.

When the System Lock is set

• When System Lock is set, the keycode input

screen appears after the power is turned on. When it appears, enter the right keycode to start projection.

Enter the same keycode in “Reconfirm”.

•You cannot use the following buttons for keycode:

•

STANDBY/ON

• ON

•

STANDBY

• ENTER

• L-CLICK

• R-CLICK/RETURN

• MENU/HELP

• System lock function recognizes each

button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.

Press the 4 buttons on the remote control or on the projector to enter the new keycode in “New Code”.

Setting the System Lock

PRJ - ADJ

Old Code

New Code

Reconfirm

****

– ––– ––––

System Lock

––––

Note

Locking the Operation Buttons on the Projector

Use this function to lock the operation buttons on the projector.

a Taking the Keylock off

Hold down ENTER on the projector for about 5 seconds.

On-screen display

a Locking the Operation Buttons

Hold down ENTER on the projector for about 5 seconds while the projector is being turned on.

On-screen display

• The keylock function does not affect the operation with the remote control buttons.

•You cannot use the keylock function while the projector is warming up.

• When the projector is in standby mode, you can release the keylock by holding down ENTER and STANDBY/ON on the projector simulta- neously for about 5 seconds.

• Keylock does not function while the projector is: displaying the “Setup Guide” or “Menu” screens, in standby mode, warming up, changing input signals, operating “Auto Sync” function, in “FREEZE” mode or on the “System Lock” screen during warming up.

Info

Keylock Function

Page 50

Troubleshooting with the “Help” Menu

Utilizing the “Help” Menu Functions

This function advises you to solve the problems during usage.

•You can adjust the items with check marks (✔).

• The items in the “Help” menu change, de-

pending on the input signal or setting that you have selected.

• If the problem is not solved, refer to

“Troubleshooting”. (see pages 61 and 62)

• When selecting “sRGB” in "Picture Mode”, the

item “Color is faded or poor” is not displayed. This means you cannot change input signal types.

Press O or Q to adjust.

If the image is not improved, select “Adjust horizontal noise”, then press ENTER.

Select “Initiate “Auto Sync” Adjustments”, then press ENTER.

Press P or R to select “Vertical stripes or flickering image appears” on Help menu, then press ENTER.

Example: When image flickering appears

Operation to solve image flickering when projecting the computer RGB signal.

Note

Press MENU/HELP.

Press O or Q to select “Help”, then press ENTER.

Adjustment buttons (P/R/O/Q)

ENTER button

MENU/HELP button

0Phase

SEL./ADJ. Rtn. Menu END

Help

There is no picture or audio

Vertical stripes or flickering image appear

Data image is not centered Color is faded or poor Picture is dark The image is distorted

Reset all adjustments to default settings

If there is no change after performing "Auto Sync" adjustments, adjust the following items.

Initiate “Auto Sync” Adjustments.

Vertical stripes or flickering image appear

Adjust vertical noise Adjust horizontal noise Reset the 2 items above Return

Signal Info 1024768

H 48.3 kHz / V 59.9 Hz

Picture SCR - ADJ PRJ - ADJ Help

Help

SEL. ENTER END

Press ENTER.

Page 51

Appendix

Cleaning the lens

■ Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens.

■ As the surface of the lens can easily get damaged, be careful not to scrape or hit the lens.

Cleaning the exhaust and intake vents

■ Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.

Cleaning the projector

■ Ensure that you have unplugged the power cord before cleaning the projector.

■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.

■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.

■ Wipe off dirt gently with a soft flannel cloth.

■ When the dirt is hard to remove, soak a cloth in

a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.

Maintenance

• If you want to clean the air vents during projector operation, ensure you press STANDBY/ON on the projector or STANDBY on the remote control and put the projector into standby mode. After the cooling fan has stopped, clean the vents.

Info

Wax

Mild detergent

Mild detergent diluted

with water

Thinner

Page 52

Maintenance Indicators

About the lamp indicator

■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red.

■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, “ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projector will enter standby mode. After “ ” appears, ensure you perform the measures described on page 49.

Lamp indicator

■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.

Temperature warning indicator

Power indicator

Lamp indicator

Red on

Power indicator

Indicators on the Projector

Green on

Normal (Standby)

Normal (Power on)

Green on

Green blinks

Normal

The lamp is warming up.

Temperature warning indicator

Off

Red on

Normal

The internal temperature is abnormally high. (See page 49.)

Red blinks Abnormal (See page 49.)

Red on

The lamp is shut down abnormally or requires to be changed. (See page 49.)

Green blinks

Normal (Cooling)

Top View

Page 53

Appendix

• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)

• If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

• The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

Maintenance indicator

Problem

The internal temperature is abnormally high.

The lamp does not illuminate.

Time to change the lamp.

The lamp does not illuminate.

The power indicator blinks in red when the projector is on.

Cause

• Blocked air intake

• Cooling fan breakdown

• Internal circuit failure

• Clogged air intake

• The lamp is shut down abnormally.

• Remaining lamp life becomes 5% or less.

• Burnt-out lamp

• Lamp circuit failure

• The lamp unit cover is open.

Possible Solution

• Relocate the projector to an area with proper ventilation. (See page 8.)

•Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 63) for repair.

• Disconnect the power cord from the AC outlet, and then connect it again.

• Carefully replace the lamp. (See page 51.)

•Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 63) for repair.

• Please exercise care when replacing the lamp.

• Securely install the cover.

• If the power indicator blinks in red even when the lamp unit cover is securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 63) for advice.

Abnormal

Red on

(Standby)

Red on

(Standby)

Red

blinks

Tempera-

ture

warning

indicator

Lamp

indicator

Power

indicator

Normal

Off

Green on

(Green

blinks

when the

lamp is

warming

up or

turning

off.)

Green on/

Red on

Green blinks

(Cooling)

Info

Page 54

Regarding the Lamp

Lamp

■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 44.)

■ Purchase a replacement lamp of type AN-XR30LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■ Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized

Projector Dealer or Service Center for repair.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

Page 55

Appendix

Removing and Installing the Lamp Unit

• Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

• Do not loosen other screws except for the lamp unit cover and lamp unit.

Press STANDBY/ON on the projec- tor or STANDBY on the remote control to put the projector into standby mode.

•Wait until the cooling fan stops.

Warning!

• Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Disconnect the power cord.

• Unplug the power cord from the AC socket.

• Leave the lamp until it has fully cooled down (about 1 hour).

Remove the lamp unit cover.

•Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

Lamp unit AN-XR30LP

Info

Optional

accessory

AC socket

User service screw (for lamp unit cover)

STANDBY/ON button

Page 56

Regarding the Lamp (Continued)

Remove the lamp unit.

• Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Insert the new lamp unit.

•Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

Replace the lamp unit cover.

• Align the tab on the lamp unit cover (1) and place it while pressing the tab (2) to close it. Then tighten the user service screw (3) to secure the lamp unit cover.

Connect the power cord.

• Plug the power cord into the AC socket of the projector.

Reset the lamp timer.

• While simultaneously holding down MENU/HELP, ENTER and R on the pro- jector, press STANDBY/ON on the pro- jector.

• “LAMP 0000H” is displayed, indicating that the lamp timer is reset.

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

Info

AC socket

Securing screws

ENTER button

MENU/HELP button

R button

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Info

STANDBY/ON button

Page 57

Appendix

Connecting Pin Assignments

COMPUTER Input/Output

Pin No. Signal

1. Video input (red)

2. Video input (green/sync on green)

3. Video input (blue)

4. Not connected

5. Not connected

6. Earth (red)

7. Earth (green/sync on green)

8. Earth (blue)

9. Not connected

10. GND

11. Not connected

12. Bi-directional data

13. Horizontal sync signal: TTL level

14. Vertical sync signal: TTL level

15. Data clock

COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals:mini D-sub 15 pin female connector

COMPONENT Input/Output

Pin No. Signal

1. PR (CR)

2. Y

3. PB (CB)

4. Not connected

5. Not connected

6. Earth (PR)

7. Earth (Y)

8. Earth (PB)

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

14. Not connected

15. Not connected

1724

DVI-D Terminal: 24 pin connector

Pin No. Signal Pin No. Signal

1. T.M.D.S data 2– 16. Hot plug detection

2. T.M.D.S data 2+ 17. T.M.D.S data 0–

3. T.M.D.S data 2 shield 18. T.M.D.S data 0+

4. Not connected 19. T.M.D.S data 0 shield

5. Not connected 20. Not connected

6. DDC clock 21. Not connected

7. DDC data 22. T.M.D.S clock shield

8. Not connected 23. T.M.D.S clock+

9. T.M.D.S data 1– 24. T.M.D.S clock–

10. T.M.D.S data 1+

11. T.M.D.S data 1 shield

12. Not connected

13. Not connected

14. +5V power

15. Ground

RS-232C Terminal: mini DIN 9 pin female connector

RD SD

RS CS

Signal NamePin No.

I/O Reference

Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected

Receive Data Send Data

Signal Ground

Request to Send Clear to Send

Input Output

Page 58

RS-232C Terminal: D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor

RD SD

RS CS

Signal NamePin No.

I/O Reference

Receive Data Send Data

Signal Ground

Request to Send Clear to Send

Input Output

CD RD SD ER SG DR RS CS CI

SignalPin No.

RS-232C Cable recommended connection: D-sub 9 pin female connector

CD RD SD ER SG DR RS CS CI

SignalPin No.

• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer).

Note

Projector

Pin No.

4 5 6

Computer

Pin No.

4 5 6

USB Terminal: Type B USB connector

VCC USB– USB+ SG

Signal NamePin No.

USB power USB data– USB data+ Signal Ground

Connecting Pin Assignments (Continued)

Page 59

Appendix

RS-232C Specifications and Command Settings

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 24 for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: * 9,600 bps/115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None * Set the projector’s baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.

Return code (0DH)

C1 C2 C3 C4 P1 P2 P3 P4

Response code format Normal response

Problem response (communication error or incorrect command)

O K

E R R

Command 4-digit Parameter 4-digit

Command format

Return code (0DH)

Return code (

0DH)

Info

• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands.

• After sending an input selection command and then receiving an “OK” response code, the projector may take some time to process the command. Please be aware that commands should be sent at intervals of at least 5 seconds.

• When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.

• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”

- When the projector receives the special commands shown above:

* The on-screen display will not disappear. * The “Auto Power Off” timer will not be reset.

- The special commands are available for applications that require continuous polling.

• If an underbar (_) appears in the parameter column, enter a space.

• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under Control Contents.

*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3. *2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response

code is received.

*3 The Lamp Timer Reset command is available only in standby mode.

Note

Page 60

RS-232C Specifications and Command Settings (Continued)

→ ←

POWR _ 1__

ProjectorComputer

Commands

Example: When turning on the projector, make the following setting.

Computer

DVI

Normal Stretch Border Normal Stretch Border

CONTROL CONTENTS

Power ON

Standby mode

(or 30-second startup time)

COMMAND

PARAMETER

RETURN

Power

Projector Condition

Lamp

Name

Input Change

Volume

Keystone

AV Mute

Freeze

Auto Sync Resize

On Off Status

Status

Power Status Quantity Usage Time(Hour) Usage Time(Minute) Life(Percentage) Model Name Check Model Name Check Projector Name Setting 1 (First 4 characters) *1 Projector Name Setting 2 (Middle 4 characters) *1 Projector Name Setting 3 (Last 4 characters) *1 Projector Name Check Computer DVI DVI-D-Computer select *2 DVI-D-Video select *2 S-Video Video Input RGB Check Input Video Check Input Mode Check Input Check

Volume (0 – 60) Volume up/down (-10 – +10)

-168 – +168 (XGA)/

-124 – +124 (SVGA) On Off On Off Start

OK OK or ERR 0 0: Normal 1: Temp High 2: Fan Error 4: Lamp Cover Open 8: Lamp Life 5% or less 16: Lamp Burn-out 32: Lamp Ignition Failure 64: Temp Abnormally High 0:Off, 4:Lamp Error

0:Standby

ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR

ERR ERR ERR

ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR

OK or ERR OK 1 0: Normal 1: Temp High 8: Lamp Life 5% or less 16: Lamp Burn-out 32: Lamp Ignition Failure

0:Off, 1:On, 2:Retry 3:Waiting, 4:Lamp Error 1:On, 2:Cooling

OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR 1:

Computer, 2: DVI or ERR

S-Video, 2: Video or ERR 1: RGB, 2: Video 1: Computer 2: DVI 3: S-Video 4: Video OK or ERR OK or ERR OK or ERR

OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR

P P P T

T T T T T T

I I I I I I I I I I

V V K

I F F A

R R R R R R

O O O A

P L L L L N N

J R R B B V V R V M C

O O E

M M R R D A A A B B B

W W W B

O P

T T

T A R N

N G G D D E E G E O H

L U Y

B B E E

J S S S S S S

R R R N

N T M L M D 1

0 B B S S D D B D D K

A D S

K K Z Z S R R R R R R

_ _

? _

_ _ _ _ _ _ _

? ? ? ?

_ _

_ _ _ _ _ _ _ _ _ _ _

_ _

? _

_ _ _ _ _ _ _

? ? ? ?

* *

_ _ _ _ _ _ _ _ _ _ _

_ _

? _

_ _ _ _ _ _ _

? ? ? ?

* * *

_ _ _ _ _ _ _ _ _ _ _

1 0 ? 1

1 1 1 1 1 1 1

1 1 2 1 2 1 2 ? ? ? ?

* * *

1 0 1 0 1 1 2 6 1 2 6

1 0 – 9999(Integer) 0, 15, 30, 45 0% – 100%(Integer) XR40X / XR30X / XR30S XR-40X / XR-30X / XR-30S OK or ERR

OK or ERR

Projector Name

Page 61

Appendix

OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR

ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR

R R R R R R

A R R R R R R R R R R R R R R R R R R

I I

I R R R R R R R R R R R R R R R R R

I R R H H H

A A A B B B

L A A A A A A A A A A A A A A A A A A A A A A A B B B B B B B B B B B B B B B B B B B B M M M

S S S S S S

P P P P P P B

S C W

I I I

B R

B C

S C W R

V V V V V V E S S S S S

I R D E O

I H T E P P P E

I S S S S S

I R D E O

I H T E E

I D D D

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _

* * * * * * *

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

* * * * * * *

_ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _

1 1 1 1 1

* * * * * * * *

_ _ _ _ _ _ _ _ _ _

1 1 1 1 1

* * * * * * * *

_ _ _ _ _ _ _ _ _ _

1 2 3 1 2 3 1 0 1 2 3 4

* * * * * * * *

* 0 1 2 1 0 1 2 1 2 0 1 2 3 4

* 1 0 1 2 1 2 0 1 2

S-Video

Video

Picture Mode

Contrast Bright Red Blue Color Tint Sharp CLR Temp Bright Boost Progressive

Picture Reset Signal Type

Audio Input

Picture Mode

Contrast Bright Red Blue Color Tint Sharp CLR Temp Bright Boost Picture Reset Signal Type

Audio Input

Dynamic Range

Normal Stretch Border Normal Stretch Border

Standard Presentation Movie Game sRGB

-30 – +30

-2 – +2 0 – +2 2D Progressive 3D Progressive Film Mode

Auto RGB Compontent Audio 1 Audio 2 Standard Presentation Movie Game sRGB

-30 – +30

-2 – +2 0 – +2

Auto RGB Compontent Audio 1 Audio 2 Auto Standard Enhanced

CONTROL CONTENTS

Power ON

Standby mode

(or 30-second startup time)

COMMAND

PARAMETER

RETURN

Resize

ALL Reset Computer INPUT

DVI INPUT

Page 62

RS-232C Specifications and Command Settings (Continued)

V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V

I I I I I

I M M M M M M M M

T T

A A A A A A A A A A A A A A A A A B B B B B B B B B B B B B B B B B N N A A A N M M E E E E E E E E M M M H H

P P P P P B C

T S C W

I R A A P P P P P B C

T S C W

I R A A C P H V R D D D S S S S S S S S B B B M M

S S S S

I R O

I H T E P P P E

I S S S S

I R O

I H T E P P P E

I L H P P E S

I Y Y Y Y Y Y Y Y G G G D D

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ _ _

* * * * *

_ _ _ _ _ _ _ _ _ _ _ _

* * * * *

_ _ _ _ _ _ _ _

* * * *

* _

_ _ _ _ _ _ _ _ _ _ _ _ _ _

1 1 1 1 * * * * * *

_ _ _ _ _ _ _

1 1 1 1 * * * * * *

_ _ _ _ _ _ _

* * * *

* _

_ _ _ _ _ _ _ _ _ _ _ _ _ _

0 1 2 3

* * * * * *

* 0 1 2 1 1 2 0 1 2 3

* 0 1 2 1 1 2

* 1

* 1 0 1 2 3 4 5 6 7 8 1 3 4 0 1

Picture Mode

Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive

Picture Reset Audio Input

Picture Mode

Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive

Picture Reset Audio Input

Standard Presentation Movie Game

-30 – +30

-2 – +2 0 – +2 2D Progressive 3D Progressive Film Mode

Audio 1 Audio 2 Standard Presentation Movie Game

-30 – +30

-2 – +2 0 – +2 2D Progressive 3D Progressive Film Mode

Audio 1 Audio 2

-150 – +150

-30 – +30

-150 – +150

-60 – +60

-96 – +96 (XGA)/-75 – +75 (SVGA) On Off Auto PAL SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N PAL-60 Logo Blue None Bright Eco + Quiet

CONTROL CONTENTS

Power ON

Standby mode

(or 30-second startup time)

COMMAND

PARAMETER

RETURN

S-Video INPUT

Video INPUT

Clock Phase H-position V-position

Image Shift OSD Display

Video System

Background

Lamp Setting

Fine Sync Adjustment Reset

Page 63

Appendix

CONTROL CONTENTS

Power ON

Standby mode

(or 30-second startup time)

COMMAND

PARAMETER

RETURN

Auto Power Off

Auto Restart

STANDBY Mode

PRJ Mode

Language

Setup Guide

System Sound

Internal Speaker

RGB Frequency Check Fan Mode

Lamp Timer Reset *3

On Off On Off Standard Eco Reverse

Invert

English Deutsch Español Nederlands Français Italiano Svenska

Português

polski Türkçe On Off On Off On Off Horizontal Vertical Normal High

ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR OK or ERR

A A A

A M M

I I I

I M M M M M M M M M M M M M M M

S S S S A A T

T H H

P P R R O O M M M M E E E E E E E E E E E E E E E E E S S S S F F

L L

O O

E U U R R

I L L L L L L L L L L L L L L L

G G N N

P P

R R M M R

W W

S S T T E E N N A A A A A A A A A A A A A A A U U D D K

K Q Q

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

1 1 1 1 1 1

_ _ _ _ _ _ _ _ _ _

1 0 1 0 1 0 1 0 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 1 0 1 0 1 0 1 2 0 1 1

On Off On Off

Page 64

Computer

Computer Compatibility Chart

• Multiple signal support Horizontal Frequency: 15-70 kHz, Ver tical Frequency: 45-85 Hz,

The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.

Pixel Clock: 12-108 MHz Sync signal: Compatible with TTL level

• Compatible with sync on green signal

• When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.

•

Optimum image quality will be achieved by matching your computer’s output resolution to the projector’s native resolution (1024K768 for the XR-40X and XR-30X models or 800K600 for the XR-30S model).

Note

DTV

27.0

31.5

37.5

27.0

31.5

37.9

27.0

31.5

27.0

31.5

37.9

26.2

31.5

34.7

37.9

37.5

43.3

31.4

35.1

37.9

46.6

48.1

46.9

53.7

40.3

48.4

56.5

60.0

68.7

45.0

47.7

62.7

47.6

47.8

55.0

66.2

67.5

64.0

34.9

49.7

60.2

68.7

60 70 85 60 70 85 60 70 60 70 85 50 60 70 72 75 85 50 56 60 70 72 75 85 50 60 70 75 85 60 60 75 60 60 60 70 75 60 60 67 75 75

640 ´ 350

640 ´ 400

720 ´ 350

720 ´ 400

640 ´ 480

800 ´ 600

1024 ´ 768

1280 ´ 720 1280 ´ 768 1280 ´ 800 1360 ´ 768 1366 ´ 768

1152 ´ 864

1280 ´ 1024 1400 ´ 1050

640 ´ 480 832 ´ 624

1024 ´ 768

1152 ´ 870

MAC 13" MAC 16"

VGA

SVGA

XGA

WXGA

SXGA

SXGA+

VGA

XGA

SXGA

✔

✔ ✔ ✔

✔ ✔

✔ ✔ ✔

✔ ✔ ✔ ✔

✔ ✔

✔

PC/MAC

Intelligent

Compression

MAC 19"

MAC 21"

SVGA

Resolution

Horizontal Frequency

(kHz)

VESA Standard

DVI-D

Support

Display

XR-40X/

XR-30X

XR-30S

Upscale

True

Intelligent

Compression

Upscale

True

Intelligent

Compression

Upscale

True

Intelligent

Compression

Upscale

Vertical Frequency

(Hz)

Signal

720P

1035I

1080I

Horizontal

Frequency (kHz)

37.5

45.0

33.8

28.1

33.8

Ver tical

Frequency (Hz)

DVI-D Support

(Compatible with HDCP)

✔

Signal

480I

480P

540P

576I

576P

Horizontal

Frequency (kHz)

15.7

31.5

33.8

15.6

31.3

Ver tical

Frequency (Hz)

DVI-D Support

(Compatible with HDCP)

✔

Page 65

Appendix

Troubleshooting

Problem Check

•Projector power cord is not plugged into the wall outlet.

• Power to the external connected devices is off.

• The selected input mode is wrong.

• Cables are incorrectly connected to the projector.

• Remote control battery has run out.

•

External output has not been set when connecting notebook computer.

• The lamp unit cover is not installed correctly.

•

If the connected DVI digital equipment is turned on before the “DVI-D” input mode is selected on the projector, the image may not be projected properly or may not be displayed at all. Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.

• Cables are incorrectly connected to the projector.

• “Bright” is set to minimum position.

• Depending on the computer you are using, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer’s operation manual for how to switch its signal output settings.

• Image adjustments are incorrectly set.

• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the “Bright Boost” value.

(Video Input only)

•Video input system is incorrectly set.

• Adjust the focus.

• The projection distance exceeds the focus range.

•

There is fog on the lens. If the projector is carried from a cold room into a warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.

(Computer Input only)

• Perform “Fine Sync” Adjustments (“Clock” Adjustment)

• Perform “Fine Sync” Adjustments (“Phase” Adjustment)

• Noise may appear depending on the computer.

• Cables are incorrectly connected to the projector.

•Volume is set to minimum.

• When the projector is connected to an external device and the volume is set to minimum, the sound is not output even if you turn up the volume of the external device.

• “Speaker” is set to “Off”.

• If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.

Page

–

29 21–24 14 21 51, 52 21

21–24 40

–

26 20

–

46 46

–

21–24

–

Color is faded or poor.

Picture appears but no

sound is heard.

Picture is blurred;

noise appears.

Sound is heard but no

picture appears

(or picture is dark).

An unusual sound is

occasionally heard from

the cabinet.

No picture and no sound

or projector does not

start.

Page 66

Problem

Maintenance indicator on

the projector illuminates

or blinks in red.

The projector cannot

be turned on or put into

the standby mode

using STANDBY/ON on

the projector.

Picture is green on

COMPUTER

(Component)/

DVI (Component).

Picture is pink

(no green) on

COMPUTER (RGB)/

DVI (RGB).

Picture is too bright and

whitish.

The cooling fan becomes

noisy.

The lamp does not light

up even after the

projector turns on.

The lamp suddenly turns

off during projection.

The image sometimes

flickers.

The lamp needs much

time to turn on. Picture is dark.

The remote control

cannot be used.

Check

• See “Maintenance Indicators”.

• The keylock is set. If the keylock is set to “ON”, all the buttons are locked.

• Change the input signal type setting.

• When you cannot select an input signal type, select “Color is faded or poor” in the “Help” menu, after selecting an item other than “sRGB” in “Picture Mode”, and then select an input signal type.

• Image adjustments are incorrectly set.

• When temperature inside the projector increases, the cooling fan runs faster.

• The lamp indicator is illuminating in red. Replace the lamp.

• Cables are incorrectly connected to the projector or the connected equipment works improperly.

• Select “Vertical stripes or flickering image appear” in the “Help” menu and make the necessary adjustments.

• If this happens frequently, replace the lamp.

• The lamp will eventually need to be changed. While the remaining lamp life draws to a close, replace the lamp.

• Operate the remote control while pointing it at the projector’s remote control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong fluorescent lamp is shining on the projector’s remote control sensor, place the projector where it will not be affected by strong light.

• The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones.

Page

46 39, 46

8, 9 47–49

48, 51

21–24

51 51

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

Troubleshooting (Continued)

Page 67

Appendix

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 61 and 62. If this operation manual does not answer your question, please contact the SHARP Service departments listed below.

U.S.A. Sharp Electronics Corporation

1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com

Canada Sharp Electronics of Canada Ltd.

(905) 568-7140 http://www.sharp.ca

Mexico Sharp Electronics Corporation

Mexico Branch

(525) 716-9000 http://www.sharp.com.mx

Latin America Sharp Electronics Corp. Latin

American Group

(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com

Germany Sharp Electronics (Europe) GMBH

01805-234675 http://www.sharp.de

U.K. Sharp Electronics (U.K.) Ltd.

08705 274277 http://www.sharp.co.uk/customersupport

Italy Sharp Electronics (Italy) S.P.A.

(39) 02-89595-1 http://www.sharp.it

France Sharp Electronics France

01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr

Spain Sharp Electronica Espana, S.A.

93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es

Switzerland Sharp Electronics (Schweiz) AG

0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch

Sweden Sharp Electronics ( Nordic ) AB

(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se

Austria Sharp Electronics (Europe) GMBH

Branch Office Austria

0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at

Benelux SHARP Electronics Benelux BV

0900-SHARPCE (0900-7427723) Nederland 9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu

Australia Sharp Corporation of Australia Pty.

Ltd.

1300-135-022 http://www.sharp.net.au

New Zealand Sharp Corporation of New Zealand

(09) 634-2059, (09) 636-6972 http://www.sharp.net.nz

Singapore Sharp-Roxy Sales (S) Pte. Ltd.

65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg

Hong Kong Sharp-Roxy (HK) Ltd.

(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk

Taiwan Sharp Corporation (Taiwan)

0800-025111 http://www.sharp-scot.com.tw

Malaysia Sharp-Roxy Sales & Service Co.

(60) 3-5125678

U.A.E. Sharp Middle East Fze

971-4-81-5311 helpdesk@smef.global.sharp.co.jp

Thailand Sharp Thebnakorn Co. Ltd.

02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com

Korea Sharp Electronics Incorporated of

Korea

(82) 2-3660-2002 lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr

India Sharp Business Systems (India)

Limited

(91) 11- 6431313 service@sharp-oa.com

Page 68

Specifications

As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

Model Display device Resolution

Lens

Input terminal

Output terminal

Control, others

Speaker Projection lamp Rated voltage Rated frequency Input current Power consumption (Standby)

Operation temperature Cabinet Dimensions (main body only)

Weight (approx.)

F number Zoom Focus DVI-D (Compatible with HDCP) RGB/Component (mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) RGB/Component (mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) USB (Type B) RS-232C (mini DIN 9 pin)

XR-40X/XR-30X/XR-30S

0.55" DLP

Chip XR-40X/XR-30X XGA (1024 × 768) XR-30S SVGA (800 × 600) F 2.5 – 2.6 Manual, ×1.15 (f = 20.4 – 23.5 mm) Manual

×1 ×1 ×1 ×1 ×1 ×1 (L/R) ×1 ×1 ×1 ×1

2 W (Mono) 200 W AC 100 – 240 V 50/60 Hz

2.9 A 283 W (4.3 W) with AC 100 V

270 W (4.4 W) with AC 240 V 41°F to 95°F (+5°C to +35°C) Plastic 10

/64" × 3 33/64" × 10 7/16"

(270 (W) × 89 (H) × 265 (D) mm)

6.4 lbs. (2.9 kg)

Page 69

Appendix

Dimensions

Units: inches (mm)

(265)

(89)

(37.65)

(66.35)

2 61/64 (75)

/64 (270)

/8 (60)

(6)

M4 M4

(104)

(49)

/32 (10)

(30)

2 61/64 (75)

(36)

Page 70

Accessories ............................................................. 10

AC socket ................................................................ 24

Adjustment buttons ................................................. 37

Aspect ratio ............................................................. 30

Audio Input .............................................................. 43

AUDIO 1, 2 terminal ................................................ 23

AUDIO OUT terminal .............................................. 23

Auto Power Off ........................................................ 43

Auto Restart ............................................................ 43

Auto Sync (Auto Sync adjustment) ............. 33, 36, 46

AUTO SYNC button ................................................ 33

AV MUTE button ...................................................... 29

Background ............................................................. 42

Batteries .................................................................. 14

Blue .......................................................................... 40

BORDER ........................................................... 30, 31

BREAK TIMER button ............................................. 32

Bright ....................................................................... 40

Bright Boost ............................................................. 40

CLR Temp (Color Temperature) .............................. 40

Color ........................................................................ 40

COMPUTER button ................................................. 29

COMPUTER/COMPONENT input terminal ...... 21, 22

Contrast ................................................................... 40

DIN-D-sub RS-232C adaptor .................................. 24

DVI button ................................................................ 29

DVI-D input terminal .......................................... 21, 22

ECO+QUIET button ................................................ 32

ENTER button ......................................................... 37

Exhaust vent ...................................................... 11, 47

Fan Mode ................................................................. 44

Fine Sync ................................................................. 46

Focus ring ................................................................ 26

FREEZE button ....................................................... 33

Front adjustment foot .............................................. 27

HEIGHT ADJUST lever ........................................... 27

Help ......................................................................... 46

H-Pos ................................................................. 36, 46

Image shift ............................................................... 41

INPUT modes .......................................................... 29

Intake vent ......................................................... 11, 47

Kensington Security Standard connector ............... 12

Keycode ................................................................... 44

Keylock .................................................................... 45

KEYSTONE button .................................................. 28

Keystone Correction .......................................... 28, 41

Lamp ........................................................................ 50

Lamp indicator ......................................................... 48

Lamp Setting ........................................................... 40

Lamp Timer (Life) .................................................... 44

Lamp unit ................................................................. 51

Language (on-screen display language) ................ 42

L-CLICK button ........................................................ 34

Lens Cap ................................................................. 11

Index

MENU/HELP button .......................................... 37, 46

MONITOR OUT terminal ......................................... 23

MOUSE/Adjustment buttons ............................. 34, 37

NORMAL ........................................................... 30, 31

ON button ................................................................ 25

Optional accessories ............................................... 10

OSD Display ............................................................ 42

PAGE DOWN button ................................................ 34

PAGE UP button ...................................................... 34

PDF ............................................................................ 9

Picture Adjustment .................................................. 39

Picture Mode ..................................................... 33, 39

PICTURE MODE button .......................................... 33

POINTER button ..................................................... 32

Power cord ............................................................... 24

Power indicator ........................................................ 48

PRJ - ADJ ................................................................ 43

PRJ Mode .......................................................... 19, 42

Progressive .............................................................. 40

R-CLICK/RETURN button ................................. 34, 37

Rear adjustment foot ............................................... 27

Red .......................................................................... 40

Remote control ........................................................ 13

Remote control sensor ............................................ 15

Replacing the lamp ........................................... 50, 51

Resize ................................................................ 30, 41

RESIZE button ........................................................ 30

RGB cable ............................................................... 21

RS-232C terminal .................................................... 24

SCR - ADJ ............................................................... 41

Screen Size and Projection Distance ..................... 20

Setup Guide ...................................................... 26, 42

Sharp ....................................................................... 40

Speaker ................................................................... 43

SPOT button ............................................................ 32

STANDBY button ..................................................... 25

STANDBY Mode ...................................................... 43

STANDBY/ON button .............................................. 25

STRETCH .......................................................... 30, 31

Supplied accessories .............................................. 10

S-VIDEO button ....................................................... 29

S-VIDEO terminal .................................................... 22

System Lock ............................................................ 44

System Sound ......................................................... 43

Temperature warning indicator ............................... 48

Tint ........................................................................... 40

USB terminal ........................................................... 34

VIDEO button .......................................................... 29

VIDEO terminal ....................................................... 22

VOL (Volume) buttons ............................................. 29

V-Pos ................................................................. 36, 46

Zoom ring ................................................................ 26

Page 71