Sharp XR-30X, XR-40X, XR-30S User Manual

MULTIMEDIA PROJECTOR
MODEL
XR-40X XR-30X XR-30S
Introduction Quick Start
Setup
OPERATION MANUAL
Connections
Basic
Features
Useful
Appendix
IMPORTANT
• For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information.
• Before recycling the packaging, please ensure that you have checked the con­tents of the carton thoroughly against the list of “Supplied accessories” on page 10.
Model No.:
Serial No.:
ii
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat­ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi­ately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth Blue : Neutral
Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
or and of the same rating as above, which is also indicated on the pin
The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol green-and-yellow.
or coloured green or
The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
iii
The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese and Korean. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch und Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois, espagnol, italien, néerlandais, portugais, chinois et coréen. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska och koreanska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español, italiano, holandés, portugués, chino y coreano. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano, olandese, portoghese, cinese e coreano. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans, Nederlands, Portugees, Chinees en Koreaans. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano, Holandês, Português, Chinês e Coreano. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
iv
Before using the projector, please read this operation manual carefully.

Introduction

Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead sym­bol, within an equilateral triangle, is in­tended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
1
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL XR-40X/XR-30X/XR-30S This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 TEL: 1-800-BE-SHARP (1-800-237-4277)
U.S.A. ONLY
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 50.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 (XR­40X/XR-30X) / 480,000 (XR-30S) pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
2

How to Read this Operation Manual

The specifications are slightly different, depending on the model. However, you can connect and operate all models in the same manner.
••
In this operation manual, the illustration and the screen display are simplified for explanation, and
••
may differ slightly from the actual display.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
Adjustment buttons (P/R/O/Q)
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Press MENU/HELP.
1
• The “Picture” menu screen for the se­lected input mode is displayed.
Press Q or O and select “Picture”
2
to adjust.
Example: “Picture” screen menu for
COMPUTER (RGB) input
Menu item
Picture SCR - ADJ PRJ - ADJ Help
Picture Mode
Contrast 0 Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset
RETURN button
•Press RETURN to return to the previous screen when the menu is displayed.
MENU/HELP button
Standard
0 0 0 0 1
Bright
Features
Useful
Buttons used in this operation
Button used in this step
On-screen display
Introduction
SEL./ADJ. ENTER END
Info
........Indicates safeguards for using the projector.
.........Indicates additional information for setting up and operating the
Note
projector.
For Future Reference
PP. 61 and 62
37
IndexMaintenance Troubleshooting
P. 6 6P. 4 7
3

Contents

Preparing
Introduction
How to Read this Operation Manual .... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
How to Access the PDF Operation
Manuals .............................................. 9
Accessories ........................................ 10
Part Names and Functions ................. 11
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Quick Start
Quick Start .......................................... 16
Using
Basic Operation
Tu r ning the Projector On/Off .............. 25
Tur ning the Projector on ....................... 25
Tur ning the Power off (Putting the
Projector into Standby Mode) ........... 25
Image Projection ................................. 26
About the Setup Guide ........................ 26
Adjusting the Projected Image ............ 26
Correcting Trapezoidal Distortion ........ 28
Switching the Input Mode .................... 29
Adjusting the Volume ........................... 29
Displaying the Black Screen and
Tur ning off the Sound Temporarily .... 29
Resize Mode ......................................... 30
Useful Features
Operating with the Remote Control .... 32
Displaying and Setting
the Break Timer ................................. 32
Displaying the Pointer .......................... 32
Using the Spot Function ...................... 32
Switching the Eco+Quiet Mode ........... 32
Auto Sync (Auto Sync Adjustment) ..... 33
Freezing a Moving Image .................... 33
Selecting the Picture Mode .................. 33
Using the Remote Control as the
Wireless Computer Mouse ................ 34
Menu Items ......................................... 35
Using the Menu Screen ...................... 37
Menu Selections (Adjustments) ........... 37
Picture Adjustment (“Picture” Menu) .. 39
Selecting the Picture Mode .................. 39
Setup
Setting up the Projector ...................... 18
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Ceiling-mount Setup ............................ 18
Projection (PRJ) Mode ......................... 19
Screen Size and Projection Distance .. 20
Connections
Connecting the Projector to
Other Equipment .............................. 21
Controlling the Projector by
a Computer ....................................... 24
Connecting the Power Cord ............... 24
Adjusting the Image ............................. 40
Adjusting the Color Temperature ......... 40
Progressive ........................................... 40
Lamp Setting ........................................ 40
Adjusting the Projected Image
(“SCR - ADJ” Menu) ......................... 41
Setting the Resize Mode ...................... 41
Adjusting the Image Position ............... 41
Keystone Correction ............................ 41
Setting the On-screen Display ............. 42
Selecting the Background Image ........ 42
Selecting the Setup Guide ................... 42
Reversing/Inverting Projected
Images ............................................... 42
Selecting the On-screen Display
Language ........................................... 42
Adjusting the Projector Function
(“PRJ - ADJ” Menu) .......................... 43
Auto Power Off Function ...................... 43
Auto Restart Function .......................... 43
STANDBY Mode ................................... 43
Setting the Confirmation Sound
(System Sound) ................................. 43
Speaker Setting .................................... 43
Audio Input ........................................... 43
Selecting the Transmission Speed
(RS-232C) .......................................... 44
Fan Mode Setting ................................. 44
Checking the Lamp Life Status ........... 44
System Lock Function .......................... 44
Keylock Function .................................. 45
Troubleshooting with the “Help” Menu ...
Utilizing the “Help” Menu Functions .... 46
46
4
Reference
Introduction
Appendix
Maintenance ....................................... 47
Maintenance Indicators ...................... 48
Regarding the Lamp ........................... 50
Lamp ..................................................... 50
Caution Concerning the Lamp ............ 50
Replacing the Lamp ............................. 50
Removing and Installing
the Lamp Unit .................................... 51
Resetting the Lamp Timer .................... 52
Connecting Pin Assignments ............. 53
RS-232C Specifications and
Command Settings ........................... 55
Computer Compatibility Chart ............ 60
Troubleshooting .................................. 61
For SHARP Assistance ...................... 63
Specifications ..................................... 64
Dimensions ......................................... 65
Index ................................................... 66
5

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with
a grounding terminal. This plug will only fit into a grounding type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.
6
Introduction
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change
in performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
• DLP® and the DLP logo are registered trademarks of Texas Instruments.
• Microsoft
®
and Windows® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
®
• Adobe
• Macintosh
Reader® is a trademark of Adobe Systems Incorporated.
®
is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.
7
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass par­ticles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Replacing the Lamp” on page 50.
Caution concerning the setup of the projector
For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more of­ten. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places exposed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
Caution regarding placing of the projector
Place the projector on a level site within the adjustment range (approx. 9 degrees) of the adjustment foot.
After the projector is purchased, a faint smell from the vent may appear when the power is first turned on. This is normal and is not a malfunction. It will disappear after the projec­tor is used for a while.
When using the projector in high-altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)
When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.
Warning about placing the projector in a high position
When placing the projector in a high position, make certain it is carefully secure to avoid personal injury caused by the projector fall­ing down.
Do not subject the projector to hard impact and/or vibration.
Protect the lens so as not to hit or damage the surface of the lens.
Rest your eyes occasionally.
Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.
Avoid locations with extremes of temperature.
The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.
Ensure that the intake vent and the exhaust vent are not obstructed.
If the cooling fan becomes obstructed, a pro­tection circuit will automatically put the pro­jector into standby mode to prevent overheat damage. This does not indicate a malfunc­tion. (See pages 48 and 49.) Remove the pro­jector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
8
Caution regarding usage of the projector
If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it.
If the power cord is unplugged while the cooling fan is running, some parts of the projector may still be hot. Use caution when handling the projector.
Do not carry the projector by holding the lens.
When storing the projector, ensure you at-
tach the lens cap to the projector. (See page
11.)
Do not expose the projector to direct sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other audio­visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.
Please read the operation manuals of the pro­jector and the equipment to be connected for instructions on how to make the connections.
Using the projector in other countries
The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.
Temperature monitor function
If the projector starts to overheat due to setup problems or blockage of the air vents, “ ” and “ ” will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warn­ing indicator on the projector will blink, and after a 60-second cooling-off period the projector will enter standby mode. Refer to “Maintenance In­dicators” on page 48 for details.
Info
The cooling fan regulates the internal tem­perature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.
Introduction

How to Access the PDF Operation Manuals

PDF operation manuals in several languages are included in the CD-ROM. To uti­lize these manuals, you need to install Adobe
®
or Macintosh®).
dows
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4 Double click the “MANUALS” folder. 5 Double click the model (name of the folder)
that you want to view.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then specify the desired file using the “File”, “Open” menu.
®
Reader® on your computer (Win-
®
(For Macintosh®, skip step 2).
6 Double click the language (name of the
folder) that you want to view.
7 Double click the pdf file to access the
projector manuals.
9

Accessories

Supplied accessories
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
Remote control
<RRMCGA581WJSA>
Power cord*
(1) (2) (3) (4)
For U.S. and
Canada, etc.
(6' (1.8 m))
<QACCDA007WJPZ>
* Use the power cord that corresponds to the wall outlet in your country.
• Operation manual (this manual <TINS-D050WJN1> and CD-ROM <UDSKAA089WJN1>)
Note
• Codes in “< >” are Replacement parts codes.
For Europe, except U.K.
(6' (1.8 m))
<QACCVA011WJPZ>
RGB cable
(10' (3.0 m))
<QCNWGA045WJPZ>
For U.K. and
Singapore
(6' (1.8 m))
<QACCBA036WJPZ>
Lens cap (attached)
<CCAPHA027WJSA>
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCLA018WJPZ>
Optional accessories
3 RCA to mini D-sub 15 pin cable (10n (3.0 m))
DIN-D-sub RS-232C adaptor (5 57/64” (15cm))
Remote receiver
Lamp unit
Ceiling-mount bracket
Extension tube
AN-C3CP2 AN-A1RS AN-MR2 AN-XR30LP AN-XRCM30 (for U.S.A.)
AN-60KT AN-TK201
AN-TK202
Note
• Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.
10

Part Names and Functions

Numbers in Z refer to the main pages in this operation manual where the topic is explained.
Projector
Top View
Introduction
Power indicator
STANDBY/ON button
For turning the power on and putting the projector into standby mode.
ENTER button
For setting items selected or adjusted on the menu.
KEYSTONE button
For entering the Keystone Correction mode.
Front View
Zoom ring
For enlarging/ reducing the picture.
Remote control sensor
Exhaust vent
25, 48
25
37
28
26
15
47
25, 48
48
32
29
29
37, 46
37
Lamp indicator
Temperature warning indicator
ECO+QUIET button
For lowering the noise of the cooling fan and extending the lamp life.
VOL (Volume) buttons (–O/Q+)
For adjusting the speaker sound level.
INPUT buttons (P/R)
For switching input mode.
MENU/HELP button
For displaying adjustment and setting screens, and help screen.
Adjustment buttons (P/R/O/Q)
For selecting menu items.
Intake vent
47
Speaker
43
HEIGHT ADJUST lever
27
Focus ring
26
For adjusting the focus.
Push both sides of the lens cap to attach or remove.
11
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the topic is explained.
Rear View
Terminals
AUDIO 1 input terminal
DVI-D input terminal
Te rminal for DVI digital RGB and digital component signals.
COMPUTER/ COMPONENT input terminal
Te rminal for computer RGB and component signals.
AUDIO OUT terminal
Audio output terminal of equipment connected to the audio input terminal.
MONITOR OUT terminal (Output terminal for computer RGB and component signals.)
Te rminal for connecting a monitor.
21 22
23
23
21 22
23
S-VIDEO input terminal
22
Te rminal for connecting video equipment with an S-video terminal.
RS-232C terminal
24
Te rminal for controlling the projector using a computer.
34
Te rminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.
AUDIO 2 input
23
terminal
VIDEO input
22
terminal
Te rminal for connecting video equipment.
USB terminal
AC socket
24
Connect the supplied
Rear adjustment foot
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.
27
power cord.
Kensington Security Standard connector
12
Introduction
STANDBY button
For putting the projector into the standby mode.
COMPUTER, DVI, S-VIDEO, VIDEO buttons
For switching to the respective input modes.
BREAK TIMER button
For displaying the break time.
PAGE UP/PAGE DOWN buttons
Same as the [Page Down] and [Page Up] keys on a computer keyboard, when with the USB connection (using a USB cable or the optional remote receiver).
POINTER button
For displaying the pointer.
MOUSE/Adjustment buttons (P/R/O/Q)
• For moving the
computer cursor when with the USB connection (using a USB cable or the optional remote receiver).
• For selecting and adjusting menu
items.
L-CLICK button
For the Left click when with the USB connection (using a USB cable or the optional remote receiver).
KEYSTONE button
For entering the Keystone Correction mode.
AUTO SYNC button
For automatically adjusting images when connected to a computer.
ECO+QUIET button
For lowering the noise of the cooling fan and extending the lamp life.
25
29
32
34
32
34 37
34
28
33
32
ON button
25
For turning the power on.
FREEZE button
33
For freezing images.
AV MUTE button
29
For temporarily displaying a black screen and turning off the sound.
VOL +/– (Volume)
29
buttons
For adjusting the speaker sound level.
32
SPOT button
For displaying the spotlight.
37
ENTER button
For setting items selected or adjusted on the menu.
34
R-CLICK/RETURN button
37
• For the Right click when with the USB connection (using a USB cable or the optional remote receiver).
• For returning to the previous menu screen during menu operations.
MENU/HELP button
37
For displaying
46
adjustment and setting screens, and help screen.
RESIZE button
30
For switching the picture size (NORMAL, BORDER, etc.).
PICTURE MODE
33
button
For selecting the appropriate picture.
13
Part Names and Functions (Continued)

Inserting the Batteries

Pull down the tab on the cover and remove the cover
1
towards the direction of the arrow.
Insert the batteries.
2
• Insert the batteries making sure the polarities correctly match
the m and n marks inside the battery compartment.
Insert the lower tab of the cover into the opening,
3
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries. This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
14

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.
Note
• The signal from the remote control can be re­flected off a screen for easy operation. How­ever, the effective distance of the signal may differ depending on the screen material.
When using the remote control
• Ensure that you do not drop it or expose it to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp. In this case, move the pro­jector away from the fluorescent lamp.
Remote control
30°
30°
Remote control signal transmitters
Introduction
Remote control sensor
23n (7 m)
15

Quick Start

This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
STANDBY/ON
8
button
INPUT buttons
6
ENTER button
4
Adjustment buttons
5
(P/R/O/Q)
KEYSTONE
5
button
Zoom ring
4
Focus ring
4
HEIGHT
4
ADJUST lever
STANDBY button
8
ON button
3
COMPUTER button
6
ENTER button
4
Adjustment buttons
5
(P/R/O/Q)
KEYSTONE button
5
1. Place the projector facing a wall or a screen
_P. 18
2. Connect the projector to the computer and plug the power cord into the AC socket of the projector
When connecting equipment other than a computer, see pages 22 and 23.
_PP. 21, 24
3. Remove the lens cap and turn the projector on
On the projector On the remote control
_P. 25
16
4. Adjust the projected image with the Setup Guide
RGB 1024 × 768
COMPUTER
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page 42.)
2 Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle).
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup
Guide.
_PP. 26, 27
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
On the projector
On the remote control
Shrinks
upper side.
Shrinks
lower side.
_P. 28
6. Select the INPUT mode
Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.
On the remote
On the
projector
• When you press INPUT on the projector, the INPUT list appears.
Press '/" to switch the INPUT mode.
control
INPUT list
INPUT
COMPUTER
D
DVI-D Computer
D
DVI-D Video
On-screen display (RGB)
_P. 29
Quick Start
7. Turn the computer on
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confirmation message is displayed to put the projector into standby mode.
On-screen display
_P. 25
On the
projector
On the remote
control
17

Setting up the Projector

Setting up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 28.)

Standard Setup (Front Projection)

Place the projector at the required distance from the screen according to the desired picture size. (See page 20.)
Example of standard setup
Side View
Screen
H
Lens center
L
Note
• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.

Ceiling-mount Setup

It is recommended that you use the optional Sharp ceiling-mount bracket for this installa­tion. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the rec­ommended ceiling-mount bracket (sold separately).
18

Projection (PRJ) Mode

The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu. See page 42.)
Ta ble mounted, front projection
[Menu item “Front”]
Ta ble mounted, rear projection
(with a translucent screen)
[Menu item “Rear”]
Ceiling mounted, front projection
[Menu item “Ceiling + Front”]
Ceiling mounted, rear projection
(with a translucent screen)
[Menu item “Ceiling + Rear”]
Indication of the Projection Image Size and Projection Distance
Example: NORMAL Mode (4:3)
Picture Size
300"
200"
100"
84" 60"
48"
67"
×
36"
80"
×
×
50"
60"
160"
×
120"
240"×180"
Setup
"
8'6
"–
7'4
(2.2 m – 2.6 m)
10'4
11'11
"–
(3.1 m
"
3.6 m)
12'3
14'2
"–
(3.7 m
"
4.3 m)
24'7
28'4
"–
(7.5 m
"
8.6 m)
36'10
(11.2 m)
Projection Distance
"
19
Setting up the Projector (Continued)

Screen Size and Projection Distance

NORMAL Mode (4:3)
Picture (Screen) size
Diag. [χ] Width Height
300(762 cm)
270(686 cm)
250(635 cm)
200(508 cm)
150(381 cm)
100(254 cm)
84(213 cm)
72(183 cm)
60(152 cm)
40(102 cm)
χ
: Picture size (diag.) (in/cm) L: Projection distance (m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the lens center to the bottom of the image (cm/in)
610 cm (240)
549 cm (216)
508 cm (200)
406 cm (160)
305 cm (120)
203 cm (80)
171 cm (67)
146 cm (58)
122 cm (48)
81 cm (32)
457 cm (180)
411 cm (162)
381 cm (150)
305 cm (120)
229 cm (90)
152 cm (60)
128 cm (50)
110 cm (43)
91 cm (36)
61 cm (24)
STRETCH Mode (16:9)
Picture (Screen) size
Diag. [χ] Width Height
250(635 cm)
225(572 cm)
200(508 cm)
150(381 cm)
133(338 cm)
106(269 cm)
100(254 cm)
92(234 cm)
84(213 cm)
72(183 cm)
60(152 cm)
40(102 cm)
χ
: Picture size (diag.) (in/cm) L: Projection distance (m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the lens center to the bottom of the image (cm/in) S: Adjustable range of image position (cm/in) See page 41.
553 cm (218)
498 cm (196)
443 cm (174)
332 cm (131)
294 cm (116)
235 cm (92)
221 cm (87)
204 cm (80)
186 cm (73)
159 cm (63)
133 cm (52)
89 cm (35)
311 cm (123)
280 cm (110)
249 cm (98)
187 cm (74)
166 cm (65)
132 cm (52)
125 cm (49)
115 cm (45)
105 cm (41)
90 cm (35)
75 cm (29)
50 cm (20)
Projection distance [L]
Minimum [L1] Maximum [L2]
11.2 m (36 10)
10.1 m (33 2)
9.4 m (30 9)
7.5 m (24 7)
5.6 m (18 5)
3.7 m (12 3)
3.1 m (10 4)
2.7 m (8 10)
2.2 m (7 4)
1.5 m (4 11)
11.7 m (38 4)
10.8 m (35 5)
8.6 m (28 4)
6.5 m (21 3)
4.3 m (14 2)
3.6 m (11 11)
3.1 m (10 3)
2.6 m (8 6)
1.7 m (5 8)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.03745 L2 (m) = 0.04323 H (cm) = 0.064
Projection distance [L]
Minimum [L1] Maximum [L2]
10.2 m (33 6)
9.2 m (30 1)
8.2 m (26 9)
6.1 m (20 1)
5.4 m (17 10)
4.3 m (14 2)
4.1 m (13 5)
3.8 m (12 4)
3.4 m (11 3)
2.9 m (9 8)
2.4 m (8)
1.6 m (5 4)
11.8 m (38 8)
10.6 m (34 9)
9.4 m (30 11)
7.1 m (23 2)
6.3 m (20 7)
5.0 m (16 5)
4.7 m (15 5)
4.3 m (14 3)
4.0 m (13)
3.4 m (11 2)
2.8 m (9 3)
1.9 m (6 2)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0408 L2 (m) = 0.0471 H (cm) = 0.27727 S (cm) = ±0.20754
Distance from the lens center to the bottom of the image [H]
19 cm
(7
(6
17 cm
(6
16 cm
(5
13 cm
(3
10 cm
(2
6 cm
(2
5 cm
(1
5 cm
(1
4 cm
(1
3 cm
χ χ
χ
Distance from the lens center to
the bottom of the image [H]
69 cm
(27
(24
62 cm
(21
55 cm
(16
42 cm
(14
37 cm
(11
29 cm
(10
28 cm
(10
26 cm
(9
23 cm
(7
20 cm
(6
17 cm
(4
11 cm
χ χ
χ
χ
9
/16)
51
/64)
19
/64)
3
/64)
25
/32)
33
/64)
7
/64)
13
/16)
33
/64)
1
/64)
[Feet/inches]
L1 (ft) = 0.03745χ / 0.3048 L2 (ft) = 0.04323χ / 0.3048 H (in) = 0.064χ / 2.54
Adjustable range of
19
9
53
3
33
37
59
3
11
55
35
23
image position [S]
/64)
52 cm
/16)
47 cm
/64)
42 cm
/8)
31 cm
/64)
28 cm
/64)
22 cm
/64)
21 cm
/64)
19 cm
/64)
17 cm
/64)
15 cm
/64)
12 cm
/64)
8 cm
[Feet/inches]
L1 (ft) = 0.0408χ / 0.3048 L2 (ft) = 0.0471χ / 0.3048 H (in) = 0.27727χ / 2.54 S (in) = ±0.20754χ / 2.54
(20
(18
(16
(12
(10
(8
(8
(7
(6
(5
(4
(3
27
/64)
25
/64)
11
/32)
1
/4)
7
/8)
21
/32)
11
/64)
33
/64)
55
/64)
57
/64)
29
/32)
17
/64)
Note
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the
bottom of the image [H]”.
• Allow a margin of error in the values in the diagrams above.
20

Connecting the Projector to Other Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.
For more details of connection and cables, refer to the operation manual of the connecting equipment.
•You may need other cables or connectors not listed below.
Terminals on the Projector

Connections

Equipment
Computer
Note
• See page 60 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-
tor. Use with computer signals other than those listed may cause some of the functions to not work.
•A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-
est Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the
computer’s external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the specific instructions in your computer's
operation manual to enable your computer’s external output port.
Terminal on
connected equipment
RGB
output
terminal
DVI digital
output
terminal
RGB cable (supplied)
DVI Digital cable (commercially available)
Cable
Terminal on the
projector
COMPUTER/ COMPONENT
DVI-D
21
Connecting the Projector to Other Equipment (Continued)
Equipment
Video equipment
Camera/Video game
Terminal on
connected equipment
HDMI
output
terminal
DVI digital
output
terminal
Component
video
output
terminal
S-video
output
terminal
Video
output
terminal
Component
video
output
terminal
S-video
output
terminal
HDMI to DVI cable (commercially available)
DVI Digital cable (commercially available)
3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)
S-video cable (commercially available)
Video cable (commercially available)
Cables for a camera or a video game/3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)
Cables for a camera or a video game
Cable
RCA adaptor plug (commercially available)
Terminal on the
projector
DVI-D
COMPUTER/ COMPONENT
S-VIDEO
VIDEO
COMPUTER/ COMPONENT
S-VIDEO
Video
output
terminal
Cables for a camera or a video game
VIDEO
Note
• While the projector is connected to video equipment that has an HDMI output terminal, only the
video signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission
may not work property. (The HDMI specification does not support all connections to video equipment that has HDMI digital output terminal using HDMI to DVI digital cable.)
• For details on compatibility for connection, see support information on DVI connection provided by
the video equipment manufacturer.
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
22
Equipment Cable
Audio equipment
Terminal on
connected equipment
ø3.5 mm
audio output
terminal
ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp service part QCNWGA038WJPZ)
Terminal on the
projector
AUDIO 1
RCA audio cable (commercially available)
Cables for a camera or a video game
RGB cable (supplied or commercially available)
ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp service part QCNWGA038WJPZ)
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
AUDIO 2
MONITOR OUT
AUDIO OUT
Monitor
Amplifier
RCA audio
output
terminal
Audio
output
terminal
RGB
input
terminal
ø3.5 mm
audio input
terminal
RCA audio
input
terminal
Note
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
•You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 43.)
• RGB signals and Component signals can be output to the monitor.
Connections
23

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS­232C adaptor (optional, AN-A1RS) and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 55 for details.
When connecting to a computer using an RS-232C serial control cable and a DIN­D-sub RS-232C adaptor
To RS-232C terminal
DIN-D-sub RS-232C adaptor (optional, AN-A1RS)
Computer
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• See pages 53 and 54 for connection of an RS-232C serial control cable.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.
Supplied
Connecting the Power
accessory
Cord
Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet.
AC socket
To AC outlet
24
Power cord (supplied)

Turning the Projector On/Off

Tur ning the Projector on

Note that the connections to external equip­ment and power outlet should be done be­fore performing the operations written be­low. (See pages 21 to 24.)
Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control.
The power indicator illuminates green.
After the lamp indicator illuminates, the projec-
tor is ready to start operation.
When “Auto Restart” is set to “On”: If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 43.)
• English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 42.
Info
Lamp indicator
Note
About the Lamp Indicator
The lamp indicator illuminates to indicate the status of the lamp.
Green: The lamp is on. Blinking in green: The lamp is warming up. Red: The lamp is shut down abnormally
When switching on the projector, a slight flicker-
If the projector is put into standby mode and
or the lamp should be replaced.
ing of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output character­istics. It should not be regarded as faulty operation.
immediately turned on again, the lamp may take some time to start projection. When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 44 for details.

Tur ning the Power off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then
press that button again while the confir­mation message is displayed, to put the projector into standby mode.
The projector cannot be turned on while cool-
ing.
Power indicator
STANDBY/ON button
STANDBY button
ON button
On-screen display (confirmation message)
Info
Direct Power Off function: You can unplug the power cord from the AC out­let even if the cooling fan is still running.
Basic
25

Image Projection

About the Setup Guide

After turning on the projector, the Setup Guide screen appears to assist you with projector setup.
Guidance items
1 FOCUS 2 HEIGHT ADJUST 3 ZOOM
Press ENTER to exit the Setup Guide screen.
Note
• The Setup Guide screen automatically high­lights the items in the following order:
1 FOCUS
However, you can adjust the focus, height (angle), or zoom regardless of the highlighted item.
• If you do not want to display the Setup Guide for the next time, set “Menu” - “SCR - ADJ” ­“Setup Guide” to “Off”. (See page 42.)
2 HEIGHT ADJUST
3 ZOOM4 ENTER
Setup Guide screen
STANDBY/ON button
ENTER button

Adjusting the Projected Image

1 Adjusting the Focus
You can adjust the focus with the focus ring on the projector.
Rotate the focus ring to adjust the fo­cus while watching the projected image.
2 Adjusting the Picture Size
You can adjust the picture size using the zoom ring on the projector.
Rotate the zoom ring to enlarge or shrink the picture size.
26
Zoom ring
Focus ring
3 Adjusting the Height
The height of the projector can be ad­justed using the adjustment feet at the front and rear of the projector.
When the screen is above the projec­tor, the projection image can be made higher by adjusting the projector.
Lift the projector to adjust its
1
height while lifting the HEIGHT ADJUST lever.
Remove your hands from the
2
HEIGHT ADJUST lever of the pro­jector after its height has been finely adjusted.
• The angle of projection is adjustable up to approx. 9 degrees from the surface on which the projector is placed.
Use the rear adjustment foot to
3
make the projector level.
• The projector is adjustable ±2 degree from the standard position.
Note
• When adjusting the height of the projector, trapezoidal distortion occurs. Follow the pro­cedures in Keystone Correction to correct the distortion. (See pages 28 and 41.)
HEIGHT ADJUST lever
Make small adjustments.
Rear adjustment foot
Basic
Info
• Do not apply too much pressure on the pro­jector when the front adjustment foot comes out.
• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector.
Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
27
Image Projection (Continued)

Correcting Trapezoidal Distortion

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
Adjustment buttons (P/R/O/Q)
Note
• The Keystone Correction can be adjusted up to an angle of approximately ±20 degrees and the screen can also be set up to an angle of approximately ±20 degrees (when the resize mode is set to “NORMAL” (see page 30)).
Press KEYSTONE to enter the
1
Keystone Correction mode.
•You can also display the on-screen dis­play of the Keystone Correction mode with KEYSTONE on the projector.
Press P/Q or O/R to adjust the
2
Keystone Correction.
•You can also adjust the Keystone Cor­rection using the adjustment buttons on the projector.
Note
•To return to the default setting, press RETURN while the on-screen display of the Keystone Correction mode is on the screen.
Press KEYSTONE.
3
• The on-screen display of the Keystone Correction mode will disappear.
•You can also use KEYSTONE on the pro- jector.
RETURN button
KEYSTONE button
On-screen display (Keystone Correction mode)
0KEYSTONE
ADJUST END
Shrinks upper side. (Move the slide bar in the + direction.)
Shrinks lower side. (Move the slide bar in the - direction.)
Info
• While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged.
28

Switching the Input Mode

Select the appropriate input mode for the connected equipment.
Press COMPUTER, DVI, S-VIDEO or VIDEO on the remote control to select
the input mode.
• When you press INPUT on the projector or DVI on the remote control, the INPUT list appears. Press P/R to switch the INPUT mode.

Adjusting the Volume

Press VOL +/– on the remote control orO/Q+ on the projector to adjust the vol-
ume.
Note
•Pressing VOL–/–O will lower the volume.
•Pressing VOL+/Q+ will raise the volume.
• When the projector is connected to external equipment, the volume level of the external equip­ment changes in accordance with the volume level of the projector. Set the projector’s volume to the lowest level when turning the projector on/ off or when changing the input signal.
• When you do not want to output the sound from the projector’s speaker while the projector is con­nected to external equipment, set “Speaker” in “PRJ-ADJ” menu to “Off”. (See page 43.)
COMPUTER, DVI, S-VIDEO, VIDEO buttons
AV MUTE button
VOL +/– (Volume) buttons
On-screen display
Basic

Displaying the Black Screen and Turning off the Sound Temporarily

Press AV MUTE on the remote control to temporarily display a black screen and turn off the sound.
Note
•Pressing AV MUTE again will turn the pro­jected image back on.
On-screen display
29
Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. De­pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.
Press RESIZE.
• See page 41 for setting on menu screen.
Computer
Main resolution
SVGA (800 K 600)
4:3 aspect ratio
Other aspect ratios
XGA (1024 K 768)
SXGA (1280 K 960)
SXGA L (1400
K
SXGA (1280
K
WXGA (1280 K 768)
1024)
1050)
NORMAL BORDER
XR-40X/30X XR-30S XR-40X/30X XR-30S XR-40X/30X XR-30S
1024
K
768 800
K
600J768
K
576 600
J
RESIZE button
K
450
1024
STRETCH
K
576 800
K
450
Computer
XR-40X/30X
Resolution
lower than
XGA
XGA
Resolution
higher than
XGA
SXGA
(1280K1024)
Input Signal
XR-30S
Resolution lower than
SVGA
SVGA
Resolution
higher
than
SVGA
Image type BORDER
NORMAL
*
4:3 aspect ratio
5:4 aspect ratio
Output screen image
*
WXGA
16:9 aspect ratio
* Mode for projecting an image with the original aspect ratio without cutting any portions.
: Cutout area on which images cannot be projected.
STRETCH
*
30
VIDEO
• “STRETCH” is fixed when 540P, 720P, 1035I or 1080I signals are entered.
Input Signal
DVD / Video Image type
4:3 aspect ratio
480I, 480P, 576I,
576P, NTSC, PAL,
SECAM
540P, 720P, 1035I,
1080I
Letter box
Squeezed 16:9 image
Squeezed 4:3 image
16:9 aspect ratio
Output screen image
NORMAL
BORDER
**
**
*
*
*
*
STRETCH
Basic
1
6:9 aspect ratio
(4:3 aspect ratio in 16:9)
* Mode for projecting an image with the original aspect ratio without cutting any portions.
: Cutout area on which images cannot be projected. : Area on which the image is not included in the original signals.
31

Operating with the Remote Control

BREAK TIMER button
POINTER button
SPOT button
Adjustment buttons (P/R/O/Q)
ECO+QUIET button

Displaying and Setting the Break Timer

Press BREAK TIMER.
1
• The timer starts to count down from 5 minutes.
On-screen display
Press P /R /O /Q to adjust the
2
length of the break time.
Increases with P or Q
5 minutes s 6 minutes s 60 minutes
Shortens with O or R
4 minutes s 3 minutes s1 minute
• The break time can be set in units of one minute (up to 60 minutes).

Displaying the Pointer

Press POINTER and press P/R/
1
O/Q on the remote control to move the pointer.
Press POINTER again.
2
• The pointer will disappear.

Using the Spot Function

Press SPOT and press P/R/O/Q
1
on the remote control to move the spot area.
Press SPOT again.
2
• The spot area will disappear.

Switching the Eco+Quiet Mode

Press ECO+QUIET on the remote con­trol or on the projector to switch the Eco+Quiet mode between on and off.
• When the Eco+Quiet Mode is set to “ON”, the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend.
Canceling the break timer display function
Press BREAK TIMER.
Note
•Break Timer does not function while the pro­jector is operating the “Auto Sync”, “FREEZE” or “AV MUTE” functions.
32
Note
• Refer to “Lamp Setting” on page 40 for de­tails of the Eco+Quiet mode.

Selecting the Picture Mode

STANDARD PRESENTATION MOVIE GAME sRGB
FREEZE button
PICTURE MODE button
AUTO SYNC button

Auto Sync (Auto Sync Adjustment)

Auto Sync function works when detect­ing input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function.
Note
• When the optimum image cannot be achieved with Auto Sync adjustment, use the help menu for manual adjustments. (See page 46.)
You can select the appropriate picture mode for the projected image, such as movie or video game.
Press PICTURE MODE.
• When pressing PICTURE MODE, the picture mode changes in the following order:
Note
• See page 39 for details on the picture mode.
* “sRGB” is displayed only when RGB signal is
input.
*

Freezing a Moving Image

Press FREEZE.
1
• The projected image is frozen.
Press FREEZE again to return to
2
the moving image from the cur­rently connected device.
Features
33
Useful
Operating with the Remote Control (Continued)

Using the Remote Control as the Wireless Computer Mouse

When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver.
Connecting with a USB cable
To USB terminal
USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ)
Computer
To USB terminal
or
The mouse pointer can be oper­ated in the following way after it is connected.
When moving the cursor
Press MOUSE/Adjustment buttons (P/R/O/Q).
When left-clicking
Press L-CLICK.
When right-clicking
Press R-CLICK.
When your computer supports only a one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK. L-CLICK and R-CLICK have common function.
When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE DOWN.
R
emote receiver
(optional, AN-MR2)
PA GE UP/ PA GE DOWN buttons
MOUSE/Adjustment buttons ('/"/\/|)
R-CLICK button
L-CLICK button
Note
• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function does not work with the following operation systems that do not support USB.
• Versions earlier than Windows® 95
• Versions earlier than Windows® NT4.0
• Versions earlier than Mac OS® 8.5
•You cannot use this function when displaying the menu screen.
• Confirm that the computer recognizes the USB connection.
34

Menu Items

Main menu Sub menu
Picture
Page 39
+30-30
Contrast
+30-30
+30-30
+30-30
2-2
+30-30
+30-30
+30-30
Tint
Color
Sharp
Bright
Red
Blue
*2*3
*2
*2
*1
*1
Progressive
Lamp Setting
*4
Reset
2D Progressive 3D Progressive Film Mode
Bright Eco + Quiet
CLR Temp
Bright Boost [0/1/2]
Page 39
Page 40
Page 40
Page 40
Page 40
Page 40
Standard Presentation Movie Game sRGB*1
Picture Mode
Main menu Sub menu
SCR - ADJ
Page 41
Language
Image Shift
Resize
Page 41
Page 41
Page 41
Page 42
Page 42
Page 42
Page 42
Page 42
Keystone
OSD Display [On/Off]
Background
Setup Guide
[On/Off]
PRJ Mode
Normal Border Stretch
Logo Blue None
Front Ceiling + Front Rear Ceiling + Rear
English Deutsch Español Nederlands Français Italiano Svenska Português
polski Türkçe
-96 +96
-75 +75
-168 +168
-124 +124*5*6
*5 *6
The following shows the items that can be set in the projector.
“Picture” menu
COMPUTER (RGB), DVI (RGB) input
Picture SCR - ADJ PRJ - ADJ Help
Picture Mode
Contrast 0 Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset
SEL./ADJ. ENTER END
COMPUTER (Component), DVI (Component), S-VIDEO, VIDEO input
Picture SCR - ADJ PRJ - ADJ Help
Picture Mode
Contrast 0 Bright Color Tint Sharp CLR Temp Bright Boost Progressive 3D Progressive Lamp Setting Bright Reset
SEL./ADJ. ENTER END
Standard
0 0 0 0 1
Bright
Standard
0 0 0 0 0 1
“Screen adjustment (SCR-ADJ)” menu
Picture SCR - ADJ PRJ - ADJ Help
Resize Image Shift 0 Keystone OSD Display Background Setup Guide PRJ Mode Language
SEL./ADJ. ENTER END
*1 Items when inputting RGB signal through COMPUTER or
DVI.
*2 Items when inputting component signal through COM-
PUTER or DVI, or when selecting S-VIDEO or VIDEO.
*3 “Tone” will appear on the menu screen only when PAL or
SECAM signals are input (including when forcibly changed to those input signals). There is basically no need to adjust “Tone”, but you can adjust the picture tone with this adjustment when inputting PAL or SECAM signals.
*4 Items when inputting component signal through
COMPUTER, or when selecting S-VIDEO or VIDEO. *5 Adjustment range for XR-40X/XR-30X. *6 Adjustment range for XR-30S.
Border
0
On Logo On Front English
Features
35
Useful
Main menu Sub menu
PRJ - ADJ
Page 43
STANDBY Mode
System Sound [On/Off]
Speaker [On/Off]
System Lock [Enable/Disable]
Lamp Timer(Life)
Page 43
Auto Restart [On/Off]
Page 43
Auto Power Off [On/Off]
Page 43
Page 43
Page 43
Page 44
Page 44
Fan Mode
Page 44
Normal High
RS-232C
Page 44
9600bps 115200bps
Audio Input
Page 43
Audio 1 Audio 2
Standard Eco
Menu Items (Continued)
“Projector adjustment (PRJ-ADJ)” menu
Picture SCR - ADJ PRJ - ADJ Help
Auto Power Off Auto Restart On STANDBY Mode Standard System Sound Speaker On Audio Input Audio 1 RS-232C 9600bps Fan Mode Normal System Lock
SEL./ADJ. ENTER END
On
On
Disable
h
0 min0Lamp Timer(Life) 100%
“Help” menu
Picture SCR - ADJ PRJ - ADJ Help
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
Reset all adjustments to default settings
SEL. ENTER END
36
The items you can set with the “Help” menu
“Help” menu n Page 46
•Vertical stripes or flickering image appear Auto Sync Clock Phase
• Data image is not centered Auto Sync H-Pos V-Pos
• Color is faded or poor COMPUTER/COMPONENT or DVI input
Signal type: Auto/RGB/Component
S-VIDEO or VIDEO input
Video System: Auto/PAL/SECAM/
NTSC3.58/NTSC4.43/ PAL-M/PAL-N/PAL-60
DVI input
Dynamic range: Auto/Standard/Enhanced
* The selectable items vary depending on the in-
put signal and the selected input mode.

Using the Menu Screen

Picture Mode
Contrast 0
0 0 0 0
Bright Red Blue
1
CLR Temp Bright Boost Lamp Setting
Standard
Bright
Reset
SEL./ADJ. ENTER END
Picture SCR - ADJ PRJ - ADJ Help
ENTER button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
Adjustment buttons (P/R/O/Q)
RETURN button
•Press RETURN to return to the previous screen when the menu is displayed.
MENU/HELP button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Press MENU/HELP.
1
• The “Picture” menu screen for the se­lected input mode is displayed.
Press Q or O and select “Picture”
2
to adjust.
Example: “Picture” screen menu for
COMPUTER (RGB) input
Menu item
Features
37
Useful
Using the Menu Screen (Continued)
0Bright
Picture
SEL./ADJ. Rtn. Menu END
15Bright
Picture Mode
Contrast 0
0 0 0
Red Blue
1
CLR Temp Bright Boost Lamp Setting
Standard
Bright
Reset
SEL./ADJ. Single ADJ END
Picture SCR - ADJ PRJ - ADJ Help
Contrast 0
0
0 0
Bright
Red Blue CLR Temp Bright Boost
1
Picture Mode
Lamp Setting
Standard
Bright
Reset
SEL./ADJ. Single ADJ END
Picture SCR - ADJ PRJ - ADJ Help
Resize Image Shift 0
0
Keystone OSD Display On
Border
Picture SCR - ADJ PRJ - ADJ Help
0
Press P or R and select “Bright”
3
to adjust.
• The selected item is highlighted.
Items to be adjusted
To adjust the projected image while watching it
Press ENTER.
• The selected item (e.g. “Bright”) is dis­played by itself at the bottom of the screen.
• When pressing P or R, the following item (“Red” after “Bright”) will be displayed.
The item displayed by itself
Press ENTER.
Note
•Press ENTER again to return to the pre­vious screen.
Press O or Q to adjust the item
4
38
selected.
• The adjustment is stored.
Press MENU/HELP.
5
• The menu screen will disappear.
Note
• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”, “FREEZE”, or “AV MUTE” functions.

Picture Adjustment (“Picture” Menu)

Picture Mode
Contrast 0
0 0 0
Bright Color Tint
0 0
Sharp
1
CLR Temp Bright Boost Progressive 3D Progressive
Standard
Reset
SEL./ADJ. ENTER END
Picture SCR - ADJ PRJ - ADJ Help
Lamp Setting Bright
Menu operation n Page 37
Q Example: “Picture” screen menu for
COMPUTER (RGB) input
Picture SCR - ADJ PRJ - ADJ Help
Picture Mode
Contrast 0 Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset
SEL./ADJ. ENTER END
1 1

1 Selecting the Picture Mode

1 1
Standard
0 0 0 0 1
Bright
Q Example: “Picture” screen menu for
S-VIDEO input
Selectable
items
Standard
Presentation
Movie
Game
*sRGB
Description
For standard image
Brightens portions of image for more enhanced presentations.
Gives natural tint to the projected image.
Gives sharpness to the projected image.
For high fidelity reproduction of images from a computer.
The default settings of each item when selecting Picture Mode
CLR Temp
0
0
–1
0
Bright Boost Lamp Setting
1
2
0
Eco + Quiet
1
• “sRGB” is displayed only when RGB signal is input.
•You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.
Note
You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.)
• *sRGB is an international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are displayed in a natural tint based on an original image, when “sRGB” is selected. For additional information about the sRGB function, visit “http://www.srgb.com/”. You cannot set the items, “Red”, “Blue”, “CLR Temp”, “Bright Boost”, when “sRGB” is selected.
Info
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a malfunction.
Bright
Bright
Bright
Bright
Features
39
Useful
Picture Adjustment (“Picture” Menu) (Continued)
Menu operation n Page 37
44

4 Progressive

22

2 Adjusting the Image

22
Adjustment
items
Contrast
Bright
1
Red*
1
Blue*
2
Color*
3
Tint*2 *
2
Sharp*
Bright Boost*
*1 Not adjustable/selectable when selecting “sRGB”. *2 Not displayed in the RGB input mode. *3 “Tone” will appear on the menu screen only when
PAL or SECAM signals are input (including when forcibly changed to those input signals). There is basically no need to adjust “Tone”, but you can adjust the picture tone with this adjustment when inputting PAL or SECAM signals .
Note
• “Bright Boost” and “CLR Temp” cannot be set when “sRGB” is selected.
•To reset all adjustment items, select “Reset” and press ENTER.
33
3 Adjusting the Color
33
For less contrast.
For less brightness.
For weaker red.
For weaker blue.
For less color intensity.
For making skin tones purplish.
For less sharpness.
1
For high fidelity color reproduc­tion.
O button
Q button
For more contrast.
For more brightness.
For stronger red.
For stronger blue.
For more color intensity.
For making skin tones greenish.
For more sharpness.
For more vividness.
Temperature
Selectable
items
For lower color temperature for –2 –1
•Values on “CLR Temp” are only for general standard purposes.
warmer, reddish incandescent-like
images. 0 1
For higher color temperature for
2
cooler, bluish, fluorescent-like images.
Note
Description
P R
44
Selectable
items
2D Progressive
3D Progressive
Film Mode
* The film source is a digital video recording with the
original encoded as is at 24 frames/second. The projector can convert this film source to progres­sive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.
• In NTSC or PAL60Hz, even if the 3D Progres­sive mode has been set, the three-two pull down enhancement will be enabled automati­cally when the film source has been entered.
• When the image is blurred or noisy, switch to the optimal mode.
• When using progressive inputs, inputs are di­rectly displayed so that 2D Progressive, 3D Progressive and Film Mode cannot be selected.
55

5 Lamp Setting

55
Selectable
items
Eco + Quiet
Bright
• In the Eco + Quiet mode, the fan sound and power consumption are lower than those in the Bright mode. (Projection brightness de­creases as shown in the chart.) The lamp life will be approximately 3,000 hours (approxi­mately 2,000 hours in the Bright mode).
Useful to display fast-moving images such as sports.
Useful to display relatively slow­moving images such as drama and documentary more clearly.
Reproduces the image of film source* clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhance­ment to progressive mode images.
Note
Brightness and Power consumption
Note
Description
Approx. 80%
100%
40

Adjusting the Projected Image (“SCR - ADJ” Menu)

Picture SCR - ADJ PRJ - ADJ Help
Resize
1
Image Shift 0
2
Keystone
3
OSD Display
4
Background
5
Setup Guide
6
PRJ Mode
7
Language
8
SEL./ADJ. ENTER END
11

1 Setting the Resize Mode

11
Note
• For details of the Resize mode, see pages 30 and 31.
•You can also press RESIZE on the remote con- trol to set the resize mode. (See page 30.)
22
2 Adjusting the Image
22
Position
You can move the projected image vertically.
Border
0
On Logo On Front English
33

3 Keystone Correction

33
When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trap­ezoidal distortion is called Keystone Correction.
Select “Keystone” on the “SCR-ADJ” menu and adjust with the slide bar.
See page 28 for details of Keystone Correction.
Menu operation n Page 37
O buttonQ button
O button
Note
•You cannot set this item when “Resize” is set to “Normal”.
Q button
Note
• The Keystone Correction can be adjusted up to an angle of approximately ±20 degrees (when “Resize” is set to “Normal”).
Features
41
Useful
Adjusting the Projected Image (“SCR - ADJ” Menu) (Continued)
Menu operation n Page 37
44
4 Setting the On-screen
44
Display
Selectable
items
On
Off
55
5
55
All on-screen displays are displayed.
INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/RESIZE/PICTURE MODE/ “An invalid button has been pressed.” are not displayed.
Selecting the Background
Description
Image
Selectable items
Logo
Blue
None
66
6 Selecting the Setup
66
Sharp logo screen
Blue screen
Description
Guide
Selectable items
On
Off
Displaying the Setup Guide when turning the projector on.
Not displaying the Setup Guide.
Description
77
7 Reversing/Inverting
77
Projected Images
Selectable items
Front
Ceiling + Front
Rear
Ceiling + Rear
See page 19 for details of Projection (PRJ) Mode.
88
8
Selecting the On-screen
88
Normal image (Projected from the front of the screen)
Inverted image (Projected from the front of the screen with an inverted projector)
Reversed image (Projected from the rear of the screen or with a mirror)
Reversed and inverted image (Projected with a mirror)
Description
Display Language
The projector can switch the on-screen display language among 15 languages.
English Deutsch Español Nederlands Français Italiano Svenska Português
42
polski Türkçe

Adjusting the Projector Function (“PRJ - ADJ” Menu)

Menu operation n Page 37
Picture SCR - ADJ PRJ - ADJ Help
Auto Power Off Auto Restart On STANDBY Mode Standard System Sound Speaker On Audio Input Audio 1 RS-232C 9600 bps Fan Mode Normal System Lock
SEL./ADJ. ENTER END
On
On
Disable
h
0 min0Lamp Timer(Life) 100%
3 3

3 STANDBY Mode

3 3
When set to “Eco”, power consumption is reduced in standby mode.
Selectable
items
Eco
Standard
The monitor output and RS-232C functions are switched off in standby mode.
The monitor output and RS-232C functions are activated even if the projector is in standby mode.
Description
11
1

Auto Power Off Function

11
Selectable
items
On
Off
• When the Auto Power Off function is set to “On”, 5 minutes before the projector enters standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.
22

2 Auto Restart Function

22
Selectable
items
On
Off
When no input signal is detected for more than 15 minutes, the projector will automatically enter standby mode.
The Auto Power Off function will be disabled.
Note
If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on.
The projector does not turn on automatically when the power cord is plugged into the AC outlet or the breaker switch is turned on.
Description
Description
44
4
Setting the Confirmation
44
Sound (System Sound)
Selectable
items
On
Off
55

5 Speaker Setting

55
Selectable
items
On
Off
6 6

6 Audio Input

6 6
66
6
66
A confirmation sound is made when the projector turns on/off.
No confirmation sound is made.
The audio signal is output from the internal speaker.
The audio signal is not output from the internal speaker.
Monitor Output
This function allows you to select an appropriate combination of audio input terminals for each input mode.
Selectable
items
Audio 1
Audio 2
The AUDIO 1 input terminal is used as an audio input terminal.
The AUDIO 2 input terminal is used as an audio input terminal.
Description
Description
Description
Features
Useful
43
Adjusting the Projector Function (“PRJ - ADJ” Menu) (Continued)
Menu operation n Page 37
77
7
Selecting the Transmission
77
Speed (RS-232C)
Make sure that both the projector and computer are set for the same baud rate.
Selectable
items
9600bps
Transmission speed is slow.
Description
P R
115200bps
88

8 Fan Mode Setting

88
This function changes the fan rotation speed.
Selectable
items
Normal
High
When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.
00
0 Checking the Lamp Life
00
Transmission speed is rapid.
Description
Suitable for normal environments.
Select this when using the projector at altitudes of approximately 1,500 meters (4,900 feet) or more.
Status
You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).
Lamp usage condition
“Life”
Operated exclusively with Lamp Setting set to “Eco +Quiet”
Operated exclusively with Lamp Setting set to “Bright”
Note
• It is recommended that the lamp be changed when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the us­age condition.
Remaining lamp life
100%
Approx. 3,000 hours
Approx. 2,000 hours
Approx. 150 hours
Approx. 100 hours
5%
99

9 System Lock Function

99
This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest you record
the keycode in a safe place where only au­thorized users have access.
Info
If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 63). Even if the product warranty is valid, the keycode reset will incur a charge.
a Setting/Changing the keycode
Select “System Lock”, then press
1
ENTER or Q.
Select “Next”, then press ENTER.
2
The screen for entering the keycode
appears.
Press the 4 buttons on the remote
3
control or on the projector to en­ter the preset keycode in “Old Code”.
When setting the keycode for the first
time, press R on the projector for four times.
Old Code
New Code Reconfirm
PRJ - ADJ
––––
–––– ––––
Setting the System Lock
Note
• If you input a wrong keycode, the cursor returns to the first point of the “Old Code”.
• The preset keycode is 4 R buttons on the projector. When you press the R but- ton four times, the keycord input screen disappears.
44
Press the 4 buttons on the remote
4
control or on the projector to en­ter the new keycode in “New Code”.
Note
•You cannot use the following buttons for keycode:
STANDBY/ON
• ON
STANDBY
• ENTER
• L-CLICK
• R-CLICK/RETURN
• MENU/HELP
System lock function recognizes each
button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.
Old Code
New Code
Reconfirm
PRJ - ADJ
****
––– ––––
––––
Setting the System Lock
Enter the same keycode in “Re-
5
confirm”.
Note
To cancel the keycode that you have already set
•Press R on the projector for four times in steps
3 and 4 above.
When the System Lock is set
• When System Lock is set, the keycode input screen appears after the power is turned on. When it appears, enter the right keycode to start projection.
Input screen for keycode
System Lock

Keylock Function

Locking the Operation Buttons on the Projector
Use this function to lock the operation buttons on the projector.
a Locking the Operation Buttons
Hold down ENTER on the projector for about 5 seconds while the projector is being turned on.
On-screen display
• The keylock function does not affect the opera­tion with the remote control buttons.
•You cannot use the keylock function while the projector is warming up.
a Taking the Keylock off
Hold down ENTER on the projector for about 5 seconds.
On-screen display
• When the projector is in standby mode, you can release the keylock by holding down ENTER and STANDBY/ON on the projector simulta­neously for about 5 seconds.
Info
• Keylock does not function while the projector is: displaying the “Setup Guide” or “Menu” screens, in standby mode, warming up, changing input signals, operating “Auto Sync” function, in “FREEZE” mode or on the “Sys­tem Lock” screen during warming up.
Features
Useful
45

Troubleshooting with the “Help” Menu

This function advises you to solve the problems during usage.

Utilizing the “Help” Menu Functions

ENTER button
Adjustment buttons
Example: When image flickering appears
Operation to solve image flickering when pro­jecting the computer RGB signal.
Press MENU/HELP.
1
Press O or Q to select “Help”, then
2
press ENTER.
Press P or R to select “Vertical
3
stripes or flickering image ap­pears” on Help menu, then press ENTER.
Picture SCR - ADJ PRJ - ADJ Help
Vertical stripes or flickering image appear
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered Color is faded or poor Picture is dark The image is distorted
Reset all adjustments to default settings
SEL. ENTER END
Press ENTER.
Vertical stripes or flickering image appear
Initiate “Auto Sync” Adjustments.
If there is no change after performing "Auto Sync" adjustments, adjust the following items.
Adjust vertical noise
Adjust horizontal noise
Reset the 2 items above
Return
Signal Info 1024768
H 48.3 kHz / V 59.9 Hz
SEL. ENTER END
Help
Select “Initiate “Auto Sync” Ad-
4
justments”, then press ENTER.
If the image is not improved, se-
5
lect “Adjust horizontal noise”, then press ENTER.
Press O or Q to adjust.
6
SEL./ADJ. Rtn. Menu END
Note
•You can adjust the items with check marks ().
• The items in the “Help” menu change, de­pending on the input signal or setting that you have selected.
If the problem is not solved, refer to
“Troubleshooting”. (see pages 61 and 62)
• When selecting “sRGB” in "Picture Mode”, the item “Color is faded or poor” is not displayed. This means you cannot change input signal types.
(P/R/O/Q)
MENU/HELP button
0Phase
Help
46

Maintenance

Cleaning the projector
Ensure that you have unplugged the power cord before cleaning the projector.
The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.
Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.
Wipe off dirt gently with a soft flannel cloth.
When the dirt is hard to remove, soak a cloth in
a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.
Mild detergent
Mild detergent diluted
with water
Cleaning the lens
Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens.
As the surface of the lens can easily get damaged, be careful not to scrape or hit the lens.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
Info
Thinner
Wax
• If you want to clean the air vents during projec­tor operation, ensure you press STANDBY/ON on the projector or STANDBY on the remote control and put the projector into standby mode. After the cooling fan has stopped, clean the vents.

Appendix

47

Maintenance Indicators

The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.
Top View
Temperature warning indicator
Lamp indicator
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, “ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec­tor will enter standby mode. After “ ” appears, ensure you perform the measures described on page 49.
About the lamp indicator
When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
Indicators on the Projector
Power indicator
Lamp indicator
Temperature warning indicator
Red on
Green on
Red blinks Abnormal (See page 49.) Green blinks
Green on
Green blinks
Red on
Off
Red on
Normal (Standby)
Normal (Power on)
Normal (Cooling)
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be changed. (See page 49.)
Normal
The internal temperature is abnormally high. (See page 49.)
48
Maintenance indicator
Tempera-
ture
warning
indicator
Lamp
indicator
Power
indicator
Green on
when the
warming
Green on/
(Cooling)
Normal
Off
(Green
blinks
lamp is
up or
turning
off.)
Red on
Green blinks
Abnormal
Red on
(Standby)
Red on
Red on
(Standby)
Red
blinks
Problem
The internal temperature is abnormally high.
The lamp does not illuminate.
Time to change the lamp.
The lamp does not illuminate.
The power indicator blinks in red when the projector is on.
Cause
• Blocked air intake
• Cooling fan breakdown
• Internal circuit failure
• Clogged air intake
• The lamp is shut down abnormally.
• Remaining lamp life becomes 5% or less.
• Burnt-out lamp
• Lamp circuit failure
• The lamp unit cover is open.
Possible Solution
• Relocate the projector to an area with proper ventilation. (See page 8.)
•Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 63) for repair.
• Disconnect the power cord from the AC outlet, and then connect it again.
• Carefully replace the lamp. (See page 51.)
•Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 63) for repair.
• Please exercise care when replacing the lamp.
• Securely install the cover.
• If the power indicator blinks in red even when the lamp unit cover is securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 63) for advice.
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug­ging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illumi­nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is con­trolled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.
Appendix
49

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 44.)
Purchase a replacement lamp of type AN-XR30LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.
Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.
U.S.A. ONLY

Replacing the Lamp

Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.
•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.
Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
50

Removing and Installing the Lamp Unit

Warning!
• Do not remove the lamp unit from the projec­tor right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.
Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
•To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
Press STANDBY/ON on the projec-
1
tor or STANDBY on the remote control to put the projector into standby mode.
•Wait until the cooling fan stops.
Disconnect the power cord.
2
• Unplug the power cord from the AC socket.
• Leave the lamp until it has fully cooled down (about 1 hour).
Optional
accessory
STANDBY/ON button
Lamp unit AN-XR30LP
AC socket
User service screw (for lamp unit cover)
Remove the lamp unit cover.
3
•Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).
1
2
Appendix
51
Regarding the Lamp (Continued)
Remove the lamp unit.
4
• Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.
Insert the new lamp unit.
5
•Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
Replace the lamp unit cover.
6
• Align the tab on the lamp unit cover (1) and place it while pressing the tab (2) to close it. Then tighten the user ser­vice screw (3) to secure the lamp unit cover.
Info
• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is con­nected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or ex­plode.
Securing screws
AC socket
52
Connect the power cord.
1
• Plug the power cord into the AC socket of the projector.
Reset the lamp timer.
2
• While simultaneously holding down MENU/HELP, ENTER and R on the pro- jector, press STANDBY/ON on the pro- jector.
• “LAMP 0000H” is displayed, indicating that the lamp timer is reset.
STANDBY/ON button
ENTER button
R button
MENU/HELP button

Connecting Pin Assignments

COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals:mini D-sub 15 pin female
connector
COMPUTER Input/Output
Pin No. Signal
1. Video input (red)
11
1
6
DVI-D Terminal: 24 pin connector
15
5
10
8
16
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
1724
1
9
COMPONENT Input/Output
Pin No. Signal
1. PR (CR)
2. Y
3. PB (CB)
4. Not connected
5. Not connected
6. Earth (PR)
7. Earth (Y)
8. Earth (PB)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
Pin No. Signal Pin No. Signal
1. T.M.D.S data 2– 16. Hot plug detection
2. T.M.D.S data 2+ 17. T.M.D.S data 0–
3. T.M.D.S data 2 shield 18. T.M.D.S data 0+
4. Not connected 19. T.M.D.S data 0 shield
5. Not connected 20. Not connected
6. DDC clock 21. Not connected
7. DDC data 22. T.M.D.S clock shield
8. Not connected 23. T.M.D.S clock+
9. T.M.D.S data 1– 24. T.M.D.S clock–
10. T.M.D.S data 1+
11. T.M.D.S data 1 shield
12. Not connected
13. Not connected
14. +5V power
15. Ground
RS-232C Terminal: mini DIN 9 pin female connector
Signal NamePin No.
1. RD
2. SD
3.
4.
5.
SG
6.
7.
RS
8.
CS
9.
Receive Data Send Data
Signal Ground
Request to Send Clear to Send
9
6
5
8
7
3
4
21
I/O Reference
Input Output
Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected
Appendix
53
Connecting Pin Assignments (Continued)
RS-232C Terminal: D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor
Signal NamePin No.
15
69
RS-232C Cable recommended connection: D-sub 9 pin female connector
51
96
1. RD
2. SD
3.
4.
5.
SG
6.
7.
RS
8.
CS
9.
SignalPin No.
1.
CD
2.
RD
3.
SD
4.
ER
5.
SG
6.
DR
7.
RS
8.
CS
9.
CI
Receive Data Send Data
Signal Ground
Request to Send Clear to Send
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer).
Projector
Pin No.
4 5 6
USB Terminal: Type B USB connector
43
12
Signal NamePin No.
1.
VCC
2.
USB–
3.
USB+
4.
SG
USB power USB data– USB data+ Signal Ground
I/O Reference
Input Output
1.
2.
3.
4.
5.
6.
7.
8.
9.
Computer
Pin No.
4 5 6
Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected
SignalPin No.
CD RD SD ER SG DR RS CS CI
54

RS-232C Specifications and Command Settings

Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 24 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: * 9,600 bps/115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None * Set the projector’s baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digit Parameter 4-digit Response code format Normal response
O K
Return code (0DH)
Problem response (communication error or incorrect command)
E R R
Return code (0DH)
Return code (
0DH)
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30
seconds after the power has been turned on, and then transmit the commands.
• After sending an input selection command and then receiving an “OK” response code, the projector
may take some time to process the command. Please be aware that commands should be sent at intervals of at least 5 seconds.
• When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1”
“TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”
- When the projector receives the special commands shown above: * The on-screen display will not disappear. * The “Auto Power Off” timer will not be reset.
- The special commands are available for applications that require continuous polling.
Note
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under Control Contents.
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3. *2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response
code is received.
*3 The Lamp Timer Reset command is available only in standby mode.
Appendix
55
RS-232C Specifications and Command Settings (Continued)
Commands
Example: When turning on the projector, make the following setting.
ProjectorComputer
OK
RETURN
(or 30-second startup time)
OK OK or ERR 0 0: Normal 1: Temp High 2: Fan Error 4: Lamp Cover Open 8: Lamp Life 5% or less 16: Lamp Burn-out 32: Lamp Ignition Failure 64: Temp Abnormally High 0:Off, 4:Lamp Error
0:Standby
ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR
ERR ERR ERR
ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR
Standby mode
POWR _ 1__
CONTROL CONTENTS
Power
Projector Condition
Lamp
Name
Input Change
Volume
Keystone
AV Mute
Freeze
Auto Sync Resize
On Off Status
Status
Power Status Quantity Usage Time(Hour) Usage Time(Minute) Life(Percentage) Model Name Check Model Name Check Projector Name Setting 1 (First 4 characters) *1 Projector Name Setting 2 (Middle 4 characters) *1 Projector Name Setting 3 (Last 4 characters) *1 Projector Name Check Computer DVI DVI-D-Computer select *2 DVI-D-Video select *2 S-Video Video Input RGB Check Input Video Check Input Mode Check Input Check
Volume (0 – 60) Volume up/down (-10 – +10)
-168 – +168 (XGA)/
-124 – +124 (SVGA) On Off On Off Start
Computer
DVI
56
Normal Stretch Border Normal Stretch Border
COMMAND
O
P
O
P
O
P
A
T
L
T
P
T
L
T
L
T
L
T
L
T
N
T
N
M
J
P
J
P
J
P
J
P
R
I
R
I
B
I
B
I
V
I
V
I
R
I
V
I
M
I
C
I
O
V
O
V
E
K
M
I
M
I
R
F
R
F
D
A
A
R
A
R
A
R
B
R
B
R
B
R
W W W B
P
O P T T T A R N
N
N
N G G D D E E G E O H
L U Y
B B E E
J S S S S S S
PARAMETER
_
R
_
R R
? _
N
_
S
_
W
_
N
_
T
_
M
_
L
_
M
_
D 1
*
2
*
3
*
_
0
_
B
_
B
_
S
_
S
_
D
_
D B
?
D
?
D
?
K
?
_
A
_
D S
*
_
K
_
K
_
Z
_
Z
_
S
_
R
_
R
_
R
_
R
_
R
_
R
→ ←
_
_
1
OK or ERR
_
_
0
OK
?
?
?
1
_
_
1
0: Normal 1: Temp High 8: Lamp Life 5% or less 16: Lamp Burn-out 32: Lamp Ignition Failure
_
_
1
0:Off, 1:On, 2:Retry 3:Waiting, 4:Lamp Error
_
_
1:On, 2:Cooling
1
_
_
1
1
_
_
1
0 – 9999(Integer)
_
_
1
0, 15, 30, 45
_
_
1
0% – 100%(Integer)
_
_
1
XR40X / XR30X / XR30S
_
_
1
XR-40X / XR-30X / XR-30S
*
*
*
OK or ERR
*
*
*
OK or ERR
*
*
*
OK or ERR
_
_
1
Projector Name
_
_
OK or ERR
1
_
_
OK or ERR
2
_
_
OK or ERR
1
_
_
OK or ERR
2
_
_
OK or ERR
1
_
_
OK or ERR
2
1:
Computer, 2: DVI or ERR
?
?
?
1:
S-Video, 2: Video or ERR
?
?
?
1: RGB, 2: Video
?
?
?
1: Computer
?
?
?
2: DVI 3: S-Video 4: Video
_
OK or ERR
*
*
OK or ERR
*
*
*
OK or ERR
*
*
*
_
_
OK or ERR
1
_
_
OK or ERR
0
_
_
OK or ERR
1
_
_
OK or ERR
0
_
_
OK or ERR
1
_
_
OK or ERR
1
_
_
OK or ERR
2
_
_
OK or ERR
6
_
_
OK or ERR
1
_
_
OK or ERR
2
_
_
OK or ERR
6
Power ON
Resize
ALL Reset Computer INPUT
DVI INPUT
CONTROL CONTENTS
S-Video
Video
Picture Mode
Contrast Bright Red Blue Color Tint Sharp CLR Temp Bright Boost Progressive
Picture Reset Signal Type
Audio Input
Picture Mode
Contrast Bright Red Blue Color Tint Sharp CLR Temp Bright Boost Picture Reset Signal Type
Audio Input
Dynamic Range
Normal Stretch Border Normal Stretch Border
Standard Presentation Movie Game sRGB
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-2 – +2 0 – +2 2D Progressive 3D Progressive Film Mode
Auto RGB Compontent Audio 1 Audio 2 Standard Presentation Movie Game sRGB
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-2 – +2 0 – +2
Auto RGB Compontent Audio 1 Audio 2 Auto Standard Enhanced
COMMAND
A
R
A
R
A
R
B
R
B
R
B
R
L
A
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
I
A
I
A
I
A
R
A
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
R
B
I
B
I
B
I
B
R
B
R
M
H
M
H
M
H
S S S S S S R P P P P P P B R B C
T S C W
I
I
I R S S S A A P P P P P P B R B C
T S C W R S S S A A B B B
PARAMETER
_
V
_
V
_
V
_
V
_
V
_
V
_
E
_
S
_
S
_
S
_
S
_
S
_
I
_
R
_
D
_
E
_
O
_
I
_
H
_
T
_
E
_
P
_
P
_
P
_
E
_
I
_
I
_
I
_
I
_
I
_
S
_
S
_
S
_
S
_
S
_
I
_
R
_
D
_
E
_
O
_
I
_
H
_
T
_
E
_
E
_
I
_
I
_
I
_
I
_
I
_
D
_
D
_
D
RETURN
Standby mode
(or 30-second startup time)
ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR
OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR
Power ON
_
_
1
_
_
2
_
_
3
_
_
1
_
_
2
_
_
3
_
_
1
_
0
1
_
1
1
_
2
1
_
3
1
_
4
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
_
*
_
_
_
_
0
_
_
1
_
_
2
_
_
1
_
_
0
_
_
1
_
_
2
_
_
1
_
_
2
_
0
1
_
1
1
_
2
1
_
3
1
_
4
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
_
*
_
_
_
_
1
_
_
0
_
_
1
_
_
2
_
_
1
_
_
2
_
_
0
_
_
1
_
_
2
Appendix
57
RS-232C Specifications and Command Settings (Continued)
CONTROL CONTENTS
S-Video INPUT
Video INPUT
Clock Phase H-position V-position Fine Sync Adjustment Reset Image Shift OSD Display
Video System
Background
Lamp Setting
Picture Mode
Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive
Picture Reset Audio Input
Picture Mode
Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive
Picture Reset Audio Input
-150 – +150
-30 – +30
-150 – +150
-60 – +60
-96 – +96 (XGA)/-75 – +75 (SVGA) On Off Auto PAL SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N PAL-60 Logo Blue None Bright Eco + Quiet
Standard Presentation Movie Game
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-2 – +2 0 – +2 2D Progressive 3D Progressive Film Mode
Audio 1 Audio 2 Standard Presentation Movie Game
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-2 – +2 0 – +2 2D Progressive 3D Progressive Film Mode
Audio 1 Audio 2
COMMAND
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
A
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
N
I
N
I
A
I
A
I
A
I
N
L
M
I
M
I
E
M
E
M
E
M
E
M
E
M
E
M
E
M
E
M
M
I
M
I
M
I
H
T
H
T
P P P P P B C T S C W
I
I
I R A A P P P P P B C T S C W
I
I
I R A A C P H V R D D D S S S S S S S S B B B M M
PARAMETER
_
S
_
S
_
S
_
S
_
I
_
R
_
O
_
I
_
H
_
T
_
E
_
P
_
P
_
P
_
E
_
I
_
I
_
S
_
S
_
S
_
S
_
I
_
R
_
O
_
I
_
H
_
T
_
E
_
P
_
P
_
P
_
E
_
I
_
I
*
L
_
H
*
P
_
P
_
E
_
S
_
I
_
I
_
Y
_
Y
_
Y
_
Y
_
Y
_
Y
_
Y
_
Y
_
G
_
G
_
G
_
D
_
D
RETURN
0
OK or ERR
1
OK or ERR
2
OK or ERR
3
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
0
OK or ERR
1
OK or ERR
2
OK or ERR
1
OK or ERR
1
OK or ERR
2
OK or ERR
0
OK or ERR
1
OK or ERR
2
OK or ERR
3
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
0
OK or ERR
1
OK or ERR
2
OK or ERR
1
OK or ERR
1
OK or ERR
2
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
*
OK or ERR
1
OK or ERR
*
OK or ERR
1
OK or ERR
0
OK or ERR
1
OK or ERR
2
OK or ERR
3
OK or ERR
4
OK or ERR
5
OK or ERR
6
OK or ERR
7
OK or ERR
8
OK or ERR
1
OK or ERR
3
OK or ERR
4
OK or ERR
0
OK or ERR
1
OK or ERR
Power ON
_
1
_
1
_
1
_
1
*
*
*
*
*
*
*
*
*
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
_
1
_
1
_
1
*
*
*
*
*
*
*
*
*
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
*
_
_
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Standby mode
(or 30-second startup time)
ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR
58
CONTROL CONTENTS
Auto Power Off
Auto Restart
STANDBY Mode
PRJ Mode
Language
Setup Guide
System Sound
Internal Speaker
RGB Frequency Check Fan Mode
Lamp Timer Reset *3
On Off On Off Standard Eco Reverse
Invert
English Deutsch Español Nederlands Français Italiano Svenska
Português
polski Türkçe On Off On Off On Off Horizontal Vertical Normal High
COMMAND
A A A A M
On Off On Off
M
I I I
I M M M M M M M M M M M M M M M S S S S A A
T
T H H
L
PARAMETER
_
_
_
W
O
P
W
O
P
S
E
R
S
E
R
T
U
O
T
U
O
E
R
M
E
R
M
N
I
M
N
I
M
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
A
L
E
U
G
E
U
G
E
D
N
S
D
N
S
K
P
S
K
P
S
Q
R
F
Q
R
F
D
M
L
D
M
L
E
R
P
1
_
_
_
0
_
_
_
1
_
_
_
0
_
_
_
1
_
_
_
0
_
_
_
1
_
_
_
0
_
_
_
1
_
_
_
0
_
_
_
1
_
_
_
2
_
_
_
3
_
_
_
4
_
_
_
5
_
_
_
6
_
_
_
7
_
_
_
8
_
_
_
9
_
_
0
1
_
_
1
1
_
_
2
1
_
_
3
1
_
_
4
1
_
_
5
1
_
_
_
1
_
_
_
0
_
_
_
1
_
_
_
0
_
_
_
1
_
_
_
0
_
_
_
1
_
_
_
2
_
_
_
0
_
_
_
1 1
0
0
0
Power ON
OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR kHz(***.* or ERR) Hz(***.* or ERR) OK or ERR OK or ERR ERR
RETURN
Standby mode
(or 30-second startup time)
ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR OK or ERR
Appendix
59

Computer Compatibility Chart

Computer
• Multiple signal support Horizontal Frequency: 15-70 kHz, Ver tical Frequency: 45-85 Hz,
The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
PC/MAC
PC
MAC 13" MAC 16" MAC 19"
MAC 21"
VGA
SVGA
XGA
WXGA
SXGA
SXGA+
VGA
SVGA
XGA
SXGA
Resolution
640 ´ 350
640 ´ 400
720 ´ 350
720 ´ 400
640 ´ 480
800 ´ 600
1024 ´ 768
1280 ´ 720 1280 ´ 768 1280 ´ 800 1360 ´ 768 1366 ´ 768
1152 ´ 864
1280 ´ 1024 1400 ´ 1050
640 ´ 480 832 ´ 624
1024 ´ 768
1152 ´ 870
Horizontal Frequency
(kHz)
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.1
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.7
62.7
47.6
47.8
55.0
66.2
67.5
64.0
64.0
34.9
49.7
60.2
68.7
Pixel Clock: 12-108 MHz Sync signal: Compatible with TTL level
• Compatible with sync on green signal
Vertical Frequency
(Hz)
60 70 85 60 70 85 60 70 60 70 85 50 60 70 72 75 85 50 56 60 70 72 75 85 50 60 70 75 85 60 60 75 60 60 60 70 75 60 60 67 75 75
75
VESA Standard
DVI-D
Support
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔
Display
XR-40X/
XR-30X
Upscale
True
Intelligent
Compression
Upscale
True
Intelligent
Compression
XR-30S
Upscale
True
Intelligent
Compression
Upscale
Intelligent
Compression
Note
When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.
Optimum image quality will be achieved by matching your computer’s output resolution to the projector’s native resolution (1024K768 for the XR-40X and XR-30X models or 800K600 for the XR-30S model).
DTV
Signal
480I
480P
540P
576I
576P
Horizontal
Frequency (kHz)
15.7
31.5
33.8
15.6
31.3
Ver tical
Frequency (Hz)
60
60
60
50
50
DVI-D Support
(Compatible with HDCP)
720P
720P
1035I
1080I
1080I
Horizontal
Frequency (kHz)
37.5
45.0
33.8
28.1
33.8
Ver tical
Frequency (Hz)
50
60
60
50
60
DVI-D Support
(Compatible with HDCP)
Signal
60

Troubleshooting

Problem Check
•Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
• Cables are incorrectly connected to the projector.
• Remote control battery has run out.
No picture and no sound
or projector does not
start.
Sound is heard but no
picture appears
(or picture is dark).
Color is faded or poor.
Picture is blurred;
noise appears.
External output has not been set when connecting notebook computer.
• The lamp unit cover is not installed correctly.
If the connected DVI digital equipment is turned on before the “DVI-D” input mode is selected on the projector, the image may not be projected properly or may not be displayed at all. Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.
• Cables are incorrectly connected to the projector.
• “Bright” is set to minimum position.
• Depending on the computer you are using, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer’s operation manual for how to switch its signal output settings.
• Image adjustments are incorrectly set.
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the “Bright Boost” value.
(Video Input only)
•Video input system is incorrectly set.
• Adjust the focus.
• The projection distance exceeds the focus range.
There is fog on the lens. If the projector is carried from a cold room into a warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.
(Computer Input only)
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
• Cables are incorrectly connected to the projector.
Page
24
29 21–24 14 21 51, 52 21
21–24 40
40
46
26 20
46 46
21–24
Picture appears but no
sound is heard.
An unusual sound is
occasionally heard from
the cabinet.
•Volume is set to minimum.
• When the projector is connected to an external device and the volume is set to minimum, the sound is not output even if you turn up the volume of the external device.
• “Speaker” is set to “Off”.
• If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.
29
43
Appendix
61
Troubleshooting (Continued)
Problem
Maintenance indicator on
the projector illuminates
or blinks in red.
The projector cannot
be turned on or put into
the standby mode
using STANDBY/ON on
the projector.
Picture is green on
COMPUTER
(Component)/
DVI (Component).
Picture is pink
(no green) on
COMPUTER (RGB)/
DVI (RGB).
Picture is too bright and
whitish.
The cooling fan becomes
The lamp suddenly turns
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
noisy.
The lamp does not light
up even after the
projector turns on.
off during projection.
The image sometimes
flickers.
The lamp needs much
time to turn on. Picture is dark.
The remote control
cannot be used.
• See “Maintenance Indicators”.
• The keylock is set. If the keylock is set to “ON”, all the buttons are locked.
• Change the input signal type setting.
• When you cannot select an input signal type, select “Color is faded or poor” in the “Help” menu, after selecting an item other than “sRGB” in “Picture Mode”, and then select an input signal type.
• Image adjustments are incorrectly set.
• When temperature inside the projector increases, the cooling fan runs faster.
• The lamp indicator is illuminating in red. Replace the lamp.
• Cables are incorrectly connected to the projector or the connected equipment works improperly.
• Select “Vertical stripes or flickering image appear” in the “Help” menu and make the necessary adjustments.
• If this happens frequently, replace the lamp.
• The lamp will eventually need to be changed. While the remaining lamp life draws to a close, replace the lamp.
• Operate the remote control while pointing it at the projector’s remote control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent lamp is shining on the projector’s remote control sensor, place the projector where it will not be affected by strong light.
• The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones.
Check
Page
48
45
46 39, 46
40
8, 9 47–49
48, 51
21–24
46
51 51
15
14
62

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 61 and 62. If this operation manual does not answer your question, please contact the SHARP Service departments listed below.
U.S.A. Sharp Electronics Corporation
Canada Sharp Electronics of Canada Ltd.
Mexico Sharp Electronics Corporation
Latin America Sharp Electronics Corp. Latin
Germany Sharp Electronics (Europe) GMBH
U.K. Sharp Electronics (U.K.) Ltd.
Italy Sharp Electronics (Italy) S.P.A.
France Sharp Electronics France
Spain Sharp Electronica Espana, S.A.
Switzerland Sharp Electronics (Schweiz) AG
Sweden Sharp Electronics ( Nordic ) AB
Austria Sharp Electronics (Europe) GMBH
1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com
(905) 568-7140 http://www.sharp.ca
Mexico Branch
(525) 716-9000 http://www.sharp.com.mx
American Group
(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com
01805-234675 http://www.sharp.de
08705 274277 http://www.sharp.co.uk/customersupport
(39) 02-89595-1 http://www.sharp.it
01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr
93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es
0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch
(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se
Branch Office Austria
0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at
Benelux SHARP Electronics Benelux BV
Australia Sharp Corporation of Australia Pty.
New Zealand Sharp Corporation of New Zealand
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
Hong Kong Sharp-Roxy (HK) Ltd.
Taiwan Sharp Corporation (Taiwan)
Malaysia Sharp-Roxy Sales & Service Co.
U.A.E. Sharp Middle East Fze
Thailand Sharp Thebnakorn Co. Ltd.
Korea Sharp Electronics Incorporated of
India Sharp Business Systems (India)
0900-SHARPCE (0900-7427723) Nederland 9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu
Ltd.
1300-135-022 http://www.sharp.net.au
(09) 634-2059, (09) 636-6972 http://www.sharp.net.nz
65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg
(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk
0800-025111 http://www.sharp-scot.com.tw
(60) 3-5125678
971-4-81-5311 helpdesk@smef.global.sharp.co.jp
02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com
Korea
(82) 2-3660-2002 lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr
Limited
(91) 11- 6431313 service@sharp-oa.com
Appendix
63

Specifications

Model Display device Resolution
Lens
Input terminal
Output terminal
Control, others
Speaker Projection lamp Rated voltage Rated frequency Input current Power consumption (Standby)
Operation temperature Cabinet Dimensions (main body only)
Weight (approx.)
F number Zoom Focus DVI-D (Compatible with HDCP) RGB/Component (mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) RGB/Component (mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) USB (Type B) RS-232C (mini DIN 9 pin)
XR-40X/XR-30X/XR-30S
0.55" DLP XR-40X/XR-30X XGA (1024 × 768) XR-30S SVGA (800 × 600) F 2.5 – 2.6 Manual, ×1.15 (f = 20.4 – 23.5 mm) Manual
×1 ×1 ×1 ×1 ×1 ×1 (L/R) ×1 ×1 ×1 ×1
2 W (Mono) 200 W AC 100 – 240 V 50/60 Hz
2.9 A 283 W (4.3 W) with AC 100 V
270 W (4.4 W) with AC 240 V 41°F to 95°F (+5°C to +35°C) Plastic 10
(270 (W) × 89 (H) × 265 (D) mm)
6.4 lbs. (2.9 kg)
®
Chip
41
/64" × 3 33/64" × 10 7/16"
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifica­tion figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
64

Dimensions

Units: inches (mm)
(6)
4
/
1
(265)
16
/
7
10
(89)
64
/
33
3
31
64
/
1
5
(37.65)
(66.35)
8
/ 2
41
/64 (270)
10
M4
M4 M4
13
/32 (10)
2 61/64 (75)
13
/32 (10)
2 61/64 (75)
2
3
1
(36)
/8 (60)
M4
27
/
64
(104)
64
/
7
4
16
/
16
15
/
(49)
3
1
(30)
1
Appendix
65

Index

Accessories ............................................................. 10
AC socket ................................................................ 24
Adjustment buttons ................................................. 37
Aspect ratio ............................................................. 30
Audio Input .............................................................. 43
AUDIO 1, 2 terminal ................................................ 23
AUDIO OUT terminal .............................................. 23
Auto Power Off ........................................................ 43
Auto Restart ............................................................ 43
Auto Sync (Auto Sync adjustment) ............. 33, 36, 46
AUTO SYNC button ................................................ 33
AV MUTE button ...................................................... 29
Background ............................................................. 42
Batteries .................................................................. 14
Blue .......................................................................... 40
BORDER ........................................................... 30, 31
BREAK TIMER button ............................................. 32
Bright ....................................................................... 40
Bright Boost ............................................................. 40
CLR Temp (Color Temperature) .............................. 40
Color ........................................................................ 40
COMPUTER button ................................................. 29
COMPUTER/COMPONENT input terminal ...... 21, 22
Contrast ................................................................... 40
DIN-D-sub RS-232C adaptor .................................. 24
DVI button ................................................................ 29
DVI-D input terminal .......................................... 21, 22
ECO+QUIET button ................................................ 32
ENTER button ......................................................... 37
Exhaust vent ...................................................... 11, 47
Fan Mode ................................................................. 44
Fine Sync ................................................................. 46
Focus ring ................................................................ 26
FREEZE button ....................................................... 33
Front adjustment foot .............................................. 27
HEIGHT ADJUST lever ........................................... 27
Help ......................................................................... 46
H-Pos ................................................................. 36, 46
Image shift ............................................................... 41
INPUT modes .......................................................... 29
Intake vent ......................................................... 11, 47
Kensington Security Standard connector ............... 12
Keycode ................................................................... 44
Keylock .................................................................... 45
KEYSTONE button .................................................. 28
Keystone Correction .......................................... 28, 41
Lamp ........................................................................ 50
Lamp indicator ......................................................... 48
Lamp Setting ........................................................... 40
Lamp Timer (Life) .................................................... 44
Lamp unit ................................................................. 51
Language (on-screen display language) ................ 42
L-CLICK button ........................................................ 34
Lens Cap ................................................................. 11
MENU/HELP button .......................................... 37, 46
MONITOR OUT terminal ......................................... 23
MOUSE/Adjustment buttons ............................. 34, 37
NORMAL ........................................................... 30, 31
ON button ................................................................ 25
Optional accessories ............................................... 10
OSD Display ............................................................ 42
PAGE DOWN button ................................................ 34
PAGE UP button ...................................................... 34
PDF ............................................................................ 9
Picture Adjustment .................................................. 39
Picture Mode ..................................................... 33, 39
PICTURE MODE button .......................................... 33
POINTER button ..................................................... 32
Power cord ............................................................... 24
Power indicator ........................................................ 48
PRJ - ADJ ................................................................ 43
PRJ Mode .......................................................... 19, 42
Progressive .............................................................. 40
R-CLICK/RETURN button ................................. 34, 37
Rear adjustment foot ............................................... 27
Red .......................................................................... 40
Remote control ........................................................ 13
Remote control sensor ............................................ 15
Replacing the lamp ........................................... 50, 51
Resize ................................................................ 30, 41
RESIZE button ........................................................ 30
RGB cable ............................................................... 21
RS-232C terminal .................................................... 24
SCR - ADJ ............................................................... 41
Screen Size and Projection Distance ..................... 20
Setup Guide ...................................................... 26, 42
Sharp ....................................................................... 40
Speaker ................................................................... 43
SPOT button ............................................................ 32
STANDBY button ..................................................... 25
STANDBY Mode ...................................................... 43
STANDBY/ON button .............................................. 25
STRETCH .......................................................... 30, 31
Supplied accessories .............................................. 10
S-VIDEO button ....................................................... 29
S-VIDEO terminal .................................................... 22
System Lock ............................................................ 44
System Sound ......................................................... 43
Temperature warning indicator ............................... 48
Tint ........................................................................... 40
USB terminal ........................................................... 34
VIDEO button .......................................................... 29
VIDEO terminal ....................................................... 22
VOL (Volume) buttons ............................................. 29
V-Po s ................................................................. 36, 46
Zoom ring ................................................................ 26
66
Loading...