Sharp SX-51A7, SX-51A8 Operation Manual
\
‘\
COLOUR TELEVISION
OPERATION MANUAL
MODEL
(OPTIONAL
IA7
TELETEXT FACILITY)
(TELETEXT MODEL)
sx-51A8
Dear SHARP Customers
a radio receiver.
Before using this COLOUR TELEVISION RECEIVER please read this Operation Manual carefully. Be
sure to save this manual for future use, especially SX51A7 owners that may update to the Teletext option.
This manual covers two models, the SX51A8 which is fitted with teletext facilities and the SX51A7 which
is sold without the Teletext facilities but can be updated to the SX51A8 model with Teletext at a later
date by purchasing the Teletext kit (No. AN222TX) from the retailer and having it installed for a fee
at a SHARP service centre.
NOTE: As purchased, the SX51A7 remote control Teletext buttons will be inoperative until the Teletext
kit has been installed in your TV.
Controls & Terminals
C
-Remote control sensor
Red I green power
indicator
1 Behind the Door 1
I
1
Opening the door
Press the upper centre of the door as
illustrated, opening it slightly. Hook your
finger inside and pull open.
Power on/off butto-
Channel selector up (A)/dow
(V) buttons
Volume. channel tunin
I
and picture adjustment
buttons
1 I
i *.i QESET 3 MODE \.‘A/\ \/CH/\
Sh P
BL’JE
t3ACh
Q
I I
Oi
I
Blueback (on /off) butrow
Picture mode select button
(contrast, colour, brightness)
Preset button
Fine tuning button
kip/Call button
2
1 Infrared Remote Control
Channel/timer call button-
TV/Video selector
Channel selectors
d
Top/Bottom/Full button---
Browse buttoReveal buttor+----
Store button
Reset button
Colour button (Red)Colour button (Green)-
Picture normal button-
Mono button
Audio mode selector(Stereo/Mono
Main/Sub/Main + Sub)
Sound mute button---
J
-Off-timer button
--Power on/off button
-Channel selectors (V/A) and
Page selectors (V/A)
4
lashback button
-Picture button
IextlMix button
-Time button
-Cancel button
--Index button
Hold button
-Colour button (Blue)
-Colour button (Yellow)
picture and sound
adjustment buttons
-Picture mode select button
‘Sound mode select button
I
I
-Volume button (V/A)
SHARP
TV.TEXT
I
NOTE: The SX51A7 Remote Control Teletext buttons will be inoperative until the AN222TX Teletext
kit has been fitted.
3
0
Battery mounting
. Insert two AA or UM-3 1.W batteries as
illustrated and replace the cover.
1 Back 1
==--
---_
====
----
----
---_
====
----
Notes
1.
The infrared transmitter requires 3 volts for
operation. If the transmitter operating
power is insufficient, replace the batteries.
2.
Position the positive and negative sides of
the batteries properly. Use of batteries other
than those specified may make the remote
control transmitter inoperative.
1
ntenna terminal
ain power on/off button
CAUTION:
Remove the power plug from the power point if
the TV is not to be used for an extended period.
)‘ideo
Video output terminal
Input terminal
I
Audio output terminals
4
@Power source and TV system
This TV set can be operated on 240V AC,
50 Hz. It is designed exclusively for PAL-B
(Australian STD) broadcast systems.
(Back)
(Behind the Door)
(Infrared Remote Control)
4
TV/VIDEO 0
on&i
&&&I
&A&
#
@ Power Supply “On/Off” with 2-Colour
(Red/Green) Power Indicator
When the main power on/off button (&I ) at
the rear of the set is pressed, the TV set
will be in standby with the power indicator
illuminated red. Then, when the power
on/off button behind the door or on the
remote control is pressed, the power
indicator will turn green and a picture will
appear on the screen. The channel
programme number is also displayed in the
upper right corner of the screen. Press the
power on/off button (01) behind the door
or on the remote control to return the set
to standby mode (the power indicator will
be illuminated red).
NOTE:
If the TV fails to turn ON, please check that
the Child Lock mode has not been
previously engaged (see page 22).
ISAGiEl
P-MODE V/IA
@ Sound volume “(V 4 A)”
The volume can be adjusted by pressing
a volume button on the set or on the remote
control. Press the Voiume (A) button to
increase the volume and the Volume (V)
button to decrease the volume. The volume
level is indicated by the number of
rectangles “I n . . ”
displayed after the
“ 4 ” in the screen.
VAA
&
5
VCHA
4 Channel Selection “ V CH A”
0
The channel number is displayed on the
screen when the Channel selector Up (A)
99
I I
button or Down (V) button is pressed on the
set or on the remote control.
When the Channel (A) button is pressed, the
channel number will change as follows:
1.2.3...38.39.1.2... Each time the Channel (V)
Channel
select
buttons
AiS&&
AA&&
lSA6z5
V CH A
A &I
&
button is pressed, the channel number will
change as follows: 39.38.37 . . . . 2.1.39.38 . . . . .
The Channel selector buttons on the
remote control can also be pressed to
directly select the desired channel. If the
factory preset channel frequencies do not
match your local channel frequencies, refer
to Presetting the Channels.
_------------_--___------------------~~
Channel Selection Using the Infrared Remote Control
Channel to be selected Channel selector button to be pressed.
Channel 1 - 9
Channel 10 - 19
Channel 20 - 29
Channel 30 - 39
Press the & - & buttons.
Press the
then the& - & button.
Note: Be sure to press the buttons within 5 seconds after the
& button is pressed. because the & button is
Press the ‘O’
then the&e& button.
Note: Refer to the note for Channel 10 - 19.
Press the & button (“3-” displayed for about 6 seconds on the
screen), and then the ,$-A button.
Note: Refer to the note for Channel 10 - 19.
& button (“l-”
cancelled in about 6 seconds.
button (‘12-” displayed for about 6 seconds), and
displayed for about 6 seconds), and
Notes:
11) The selected channel number will appear on the screen for about 3 seconds before it
disappears and the TV screen returns to its normal state.
12) When the Channel selector (A) or (V) button on the TV set or on the remote control
is held down, the channel number changes once per second. Release the Channel (A)
or (Vj button when the desired channel number appears on the screen.
1.
SKIP FINE PRESET P-MODE
@ - @ Presetting the Channels
(AUTO SEARCH TUNING SYSTEM)
oop
CALL
(ON SCREEN)
VHF-L 111.. . . . . . . . . .
T
M mory TV
station
Band lndicato
(VHF-L, VHF-H, UHF)
“1 1
1
Channel
Number
Note: Most channels are preset at the factory.
To avoid unnecessary resetting, check the
tuning of all channels before resetting them.
1. Press the Preset button behind the door
and the band, VHF or UHF, that you wish to
preset. Press the button once for the VHF
band. Press again for the UHF band. Press
again when you have finished presetting the
channel. (VHF-L l-5, VHF-H 5a-11, UHF
28-69).
2.
VCHA
:hannel
elect
uttons
UHF 111 . . . . . . . .
,,39 I
UHF
(green- red- green)
111 I . . . . . . ..-
t
1
2. Select the channel number (l-39) you
wish to store with the Channel selector
(A) button on the TV or the remote
control.
3. Next press the Volume up (A) or down,
4
(V) button on the TV. The band
indicator will turn red and the TV will
begin to search for a television
broadcast. The band indicator will turn
green when television broadcast has
been found.
4. Repeat steps 2 and 3 to preset the
other channels.
5. Press the reset button to return to the
normal mode. A green channel number
will be displayed on the screen for a
short period.
SKIP FINE PRESET P-MODE
SKIP FINE PRESET P-MODE V/1/Y VCHA
a- @ Fine tuning
When receiving a channel that is weak
the signal can sometimes be improved
by turning off the Automatic Fine
Tuning (AFT). By pressing the FINE
button and at the same time pressing
either the (A) or (V) volume buttons.
Fine tune the channel to your
preference. The AFT will now be turned
off and this will be indicated by the
channel turning yellow. To turn the AFT
back on first press the preset button
until the band indicator and the picture
is visible, then press both the FINE and
either the (A) or (V) volume buttons
momentarily. Press the preset switch
until the band indicator disappears.
The AFT will now be turned on and this
will be indicated by the channel
number turning green.
7
Loading...