1. MEASURE TO PREVENT DAMAGE FROM OCCURRING TO THE DRAWER CONNECTOR IN THE DRUM
DRIVE UNIT SECTION.
2. MEASURE TO ALLEVIATE PROBLEMS OF JAMS IN THE ADU UNIT.
3. MEASURE TO ESTABLISH INTERCHANGEABILITY OF PARTS BETWEEN MODELS CARRIED OUT AS A
MEASURE TO IMPROVE PRODUCTIVITY.
4. MEASURE TO IMPROVE OPERATIONABILITY AFTER THE MACHINE HAS BEEN CLEARED OF JAMS.
5. CHANGE IN THE SHAPE OF PARTS AND CHANGE IN MATERIALS CARRIED OUT AS A MEASURE TO
IMPROVE PRODUCTIVITY.
No. : SP-2159
1. Measure to prevent damage from occurring to the drawer connector in the drum
drive unit section.
1.Model Name:SF-2050
2.General:There was a problem of damage sometimes occurring to the drawer connector. The
damaged was caused because the insertion hole for the drawer connector of the DV
joint in the drum drive unit was too small. As a measure to alleviate this problem the hole
has been slightly enlarged. In addition to the change described above, a change has
been carried out in the shape of a portion of the attachment plate for the main PWB.
This change has been carried out as a measure to establish interchangeability between
the model listed above and other models.
DV joint plate D
Added marking
3.Description:
The dimensions have
been enlarged 1.5.
The dimensions have
been widened 1 mm.
Abnormally shaped hole
The dimensions have
been widened 1 mm.
The dimensions have
been widened 1 mm.
4.Action:From 1997 mid-June production.
Added hole for the PWB
supporter (in two locations).
1/4
SHARP CORPORATIONReprography Division
Green
C
2. Measure to alleviate problems of jams in the ADU unit.
1.Model Name:SF-2050
2.General:There was a problem of copy paper jams sometimes occurring especialy on the
inch-size papers. This problem was caused because the space between the fixing plate
and the standard plate of the ADU unit was too small. As a measure to alleviate this
problem, a change has been carried out in the shape of the fixing plate to increase the
space.
Fixing plate assembly
(CPLTM4939FC01-02)
3.Description:
Cut 2 mm
Cut 2 mm
4.Action:From 1997 mid-June production.
3. Measure to establish interchangeability of parts between models carried out as a
measure to improve productivity.
1.Model Name:SF-2050
2.General:A change has been carried out in the shape of some of the parts that are used in the
fusing unit. This change has been carried out as a measure to establish
interchangeability of the parts between the model listed above and other models.
3.Description:
Fusing R lower frame
FU rear lower paper guide
Fusing F lower frame
Added notch
4.Action:From 1997 mid-June production.
2/4
A change has been carried out
in the width of the notches.
4. Measure to improve operationability after the machine has been cleared of jams.
1.Model Name:SF-2050
2.General:The opening angle of the paper delivery reversion unit section has been increased. This
change has been carried out as a measure to improve operationability when the
machine has been cleared of copy paper jams in the paper delivery reversion unit
section.
3.Description:A change has been carried out in the shape of the paper delivery fixing plate. This
change has been carried out in order to enlarge the opening angle of the paper delivery
reversion unit section described above.
An ‘‘N’’ mark has been added for units
after the change has been carried out.
A change has been carried
out in the bend angle.
4.Action:From 1997 mid-June production.
5. Change in the shape of parts and change in materials carried out as a measure to
improve productivity.
1.Model Name:SF-2050
2.General:The changes described below have been carried out in the transport upper paper guide
in the transport unit. These changes have been carried out as a measure to improve
productivity.
3.Description:<1> The direction of the return (burr) of the edge section has been reversed, and is now
on the mylar attachment surface side. This change eliminates the affects of the copy
paper flow.
<2> The material has been changed from silver top to SECC-TJ.
Transport upper PG F
Added hole (ø5)
Side face diagram
The direction of the return has been
changed to the direction specified.
4.Action: ∗<1> → From the start of 1997 June production.
<2> → From the start of 1997 July production.
3/4
Ref.
No.
Model
name
Version P/G No.
Current partsNew parts
Parts codeParts code
Price
rank
Parts name
Effec-
tive
time
Inter-
change-
ability
Note
1
237 -5CPLTM4939FC01CPLTM4939FC02 APFixing plate3
SF-2050All
3
4
521 -36PGIDH1554FCZZPGIDH1554FCZ1AHTransport upper paper guide F∗1
<Interchange>
1. Interchangeable.4. Not interchangeable.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
Parts marked with ‘‘’’ is important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
30 -49CPLTM4822FC01CPLTM4822FC02 AM DV joint plate D
13 -34
17 -22PGIDM1626FCZ1PGIDM1626FCZ2AQ Fusing rear lower paper guide
17 -19
17 -28CFRM-0862FC01CFRM-0862FC02APFusing R lower frame
20 -29CPLTM4854FCC01 CPLTM4854FC02ALDelivery fixing plate F
20 -25CPLTM4853FC01CPLTM4853FC02ALDelivery fixing plate R
LPLTM4813FCZZLPLTM4813FCZ1AQ Main PWB fixing plate1
CFRM-0861FC01CFRM-0861FC02APFusing F lower frame
5. Interchangeable if replaced with same types of
related parts in use.
6. Others.
Mid-
’97/6
3
1
3
4/4
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.