
Date: Nov. 5, 1996
COPIER (OPTION) : SF-A56
1. MEASURE TO IMPROVE THE PERFORMANCE OF THE OPENING AND CLOSING
SWITCH OF THE PAPER SUPPLY COVER.
2. CHANGE IN THE STAGE SCREW OF THE PAPER SUPPLY COVER.
3. APPLICATION OF A BONDING AGENT TO THE SEPARATOR HOLDER.
No. : SP-2055
1. Measure to improve the performance of the opening and closing switch of the paper
supply cover.
1.Model Name: SF-A56/A17
2.General: The measure described below has been carried out to improve the performance of the
opening and closing switch ON of the paper supply cover in the models listed above.
3.Description: The length of the actuator of the paper supply cover has been changed from 7.3 mm to
8.3 mm.
Opening and closing SW actuator
Paper feed cover
4.Action: From 1996 July production.
SHARP CORPORATION Reprography Division
1/3
Green
C

2. Change in the stage screw of the paper supply cover.
1.Model Name: SF-A54/A55
2.General: When the gap between the paper feed cover and the DF cover is small, the two covers
sometimes get caught on each other when opened or closed. To alleviate this problem
the measure described below has been carried out.
3.Description: As a measure to alleviate the problem mentioned above, the stage screw attaching the
paper feed cover has been changed only on the right side.
Old 0CW2078P119B/ Q’ty: 2
↓
New 0CW2078P1 19B/ Q’ty: 1 (Q’ty2 → 1)
0CW2078P023B/ Q’ty: 1 (added)
The change has been carried
out only on the R side
4.Action: From 1996 September production.
2/3

3. Application of a bonding agent to the separator holder .
1.Model Name: SF-A55
2.General: Previously the front separator rubber- 90 pads were attached to the separator holder
with double sided tape, but there was a danger of the pads peeling off. As a measure to
alleviate this problem a bonding agent has been applied.
3.Description: The measure described above should be carried out as shown in the figure below.
Glue application
SONY Bond Tough
Applying amount : 10-20mg (Approximately two drops.)
Separator holder
0CW2198P006//
Not oozing out the glue from the height and width of the R sheet (PF2198P317A/).
4.Action: From 1995 December production.
Ref.
Model
No.
SF-A17
1
SF-A56
SF-A54
2
SF-A55
SF-A54
3
SF-A55
<Interchange>
1. Interchangeable. 4. Not interchangeable.
2. C urr e nt t y pe c a n be u s ed i n p la ce of new ty pe .
New ty pe cann ot be us ed i n place of curr ent type .
3. C urre nt ty pe cann ot be used i n place of new ty pe.
New t y pe c a n be u sed in p la ce of curr en t ty p e.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
name
Version P/G No.
4 -21
4-5
All
1-5
1
5
!
Current parts New parts
Parts code Parts code
0CW2214P008// 0CW2214P008C/ BA
0CW2078P119B/ 0CW2078P023B/ AC Screw 96/9
— 0CW2198K070// AP
Front separator rubber - 90
Price
rank
5. Interchangeable if replaced with same types of
relate d parts in use .
6. Others.
Parts name
Paper feeding
cover
Separator
holder ass’y
Effec-
Inter-
tive
change-
time
ability
96/7
95/12 6
Note
3
3/3