SHARP SP1884 Technical Report
Date: Jun. 9, 1995
COPIER (OP TI O N ) : SF-S16
No. : SP-1884
ATTACHMENT OF THE SF-S16 TO THE NEW
PRODUCTS (MODEL SF-2050).
1.Model name: SF-S16
2.General: The SF-S16 is established as a sorter for model SD-2060. In order to make it possible
for the unit to be installed on the new model (SF-2050), some parts have been either
added or changed.
3.Description:
Changed joint S plate H.
It is possible to use the changed
part with either the SD-2060 or
with the new models.
(Old)
Sorter receiving plate.
(New)
1
B
A
Added RK-MG receiving plates for
new models, incl uded in the boxes.
No changes should be made when
used with model SD- 2060. When
used with the new models, the parts
should be replaced.
Transfer guide.
Added and packaged together with
the new models. (I nt erchangeable
with model SF-S15).
This part is interchanged by
changing the installment
direction. Direction “A” is for
model SD-2060, and direction
“B” is for new models.
Joint S plate H
0CW4050P061A/
RK plate H
0CW4050P070A/
SHARP CORPORATION Reprography Division
1/2
Green
C
PK-MG receiving plate.
(SD-2060)
(For new models)
2
0CW4050P069A/
Transfer guide
(not necessary for model SD-2060)
The changes described above are carried out from 1995 January production. In order
to distinguish them from other units, they have been marked in the locations shown in
the figure to the right.
Note:
In consideration of a way to use with new
models those units left in stock that were
manufactured before 1995 January production,
parts ➀ ➁ and ➂ described above have been
established as a kit to be offered with the
installation procedures manual.
4.Action: From the start of 1995 January production.
3
0CW4043P009D/
Side “D” is opposite of
side “C”.
Side “C”
φ15 stamp has been added to the
right of the “SF-S16" characters on
side ”C" and “D”. (color: black).
2/2
Ref.
Model
No.
SF-S16
<Interchange>
1. Interc ha ng ea bl e. 4. N ot i nt er ch an ge ab l e.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
sp eci fi e d on es fo r m ain ta in i ng t he s a fe ty an d pe rf o rma nc e o f th e s et .
name
Version P/G No.
4
All
4
4
U.S.A
U.K
Australia
Canada
SEEG
Other EX
4
4
!
Current parts New parts
rank
AP
Parts name
PK-MG hold
plate
Parts code Parts code
0CW4050P061A/ 0CW4050P070A/ AG PK plate H
—
— 0CW4043P009D/ AV Transfer guide
— 0CW4050K123A/ BE Kit — —
— 0CW4050K124A/ BG Kit — —
0CW4050P069A/
(Q’ty: 2)
Price
5. Interchangeable if replaced with same types of
relate d parts in use .
6. Others .
Effec-
tive
time
1st lot
’95/1
1st lot
’95/1
1st lot
’95/1
Inter-
change-
ability
—
—
Note
Loading...