Sharp SKMD30E3DS User Manual

30" EXTENSION KIT: SKMD30E3DS

INSTALLATION INSTRUCTIONS

IMPORTANT NOTES TO THE INSTALLER

• Read all of the Installation Manual that is included with the Microwave Drawer before installing the extension kit.

• Observe all governing codes, ordinances, and safety instructions.

• Be sure to leave these instructions with the consumer.

Parts included:

Trim Screws (qty. 4)

XOTS740PO8000

Bracket Screws (qty. 8)

LX-CZB073MRE0

Left Side Trim (qty. 1)

GWAKPB282MRF0

Right Side Trim (qty. 1)

GWAKPB283MRF0

Mounting Brackets (qty. 2)

LBRC-B029MRT0

Install the extension kit after properly installing the microwave drawer in the cabinet. See steps below.

Note that the side trims are marked "L" and "R" on the back side.

MICROWAVE DRAWER STANDARD MOUNT, MEASUREMENTS AND INSTALLATION INSTRUCTIONS

B

C

F

A

J

G

I

D

A. 21-5/8" (549.3 mm)
B. 4-11/16" (119.1 mm)
C. 1-3/4" (44.5 mm)
D. 21-7/8" (555.6 mm)
E. 23-5/8" (600.1 mm)
F. 16" (406.4 mm)
G. 14-19/32" (370.7 mm)
H. 1-17/32" (38.9 mm) door thickness
I. 15" (381.0 mm) auto drawer opening
J. 4" (101.0 mm)

Figure 1

H

E

E 1

TINSKB263MRR0

B

M

G

I

O

L

D

F

K

J

Q

I

O

Figure 2

A. 6" (152.4 mm)
B. Suggested electrical outlet location*
C. Anti-Tip block
D. 5" (127.0 mm)
E. 3-1/2" (88.9 mm)
F. 4" (101.6 mm)
G. 22-1/8" (562.0 mm) opening
H. 14-13/16" (376.2 mm) to bottom of Anti-Tip block
I. Allow 7/8" (22.2 mm) overlap
J. 23-1/2" (596.9 mm) minimum depth
K. Allow 7/16" (11.1 mm) overlap
L. 36" (914.4 mm) countertop height
M. Allow 7/16" (11.1 mm) minimum space
N. Floor must support 100 lb (45.4 kg)
O. Allow 4-1/8" (104.4 mm) minimum space
P. 15-9/16" (395.3 mm) opening
Q. 30" (762.0 mm) minimum width

A

C

E

1. Prepare cabinet opening as shown in Figure 2.

2. Place the drawer adjacent to the wall or cabinet opening. Plug
the power supply cord into the electrical outlet.

3. Carefully guide the drawer into the prepared opening. Avoid
contact with the sides of the cutout opening and also pinching

H

the cord between the oven and the wall.

4. Slidethedrawerallthewaybackuntilthesiderailsareush

P

with the face of the cabinet.

5. Open the drawer. Using the 4 holes on the drawer as a template,

N

pre-drill the cabinet using a 1/16” (1.6 mm) bit. Secure the
drawer with the 4 screws supplied. See Figure 3.

Side

Figure 3

Rail

6. Close drawer to complete oven installation. See Figure 4.

Figures 1 and 2 contain many Microwave Drawer measurements
for reference when planning the drawer’s location.

This Microwave Drawer can be installed below any electric or
gas wall oven.

* Can also be installed using an electrical outlet in an adjacent cabinet

within the area where the provided electrical cord can reach. Power
cord access hole in cabinet should be a minimum 1-1/2" diameter
hole and deburred of all sharp edges.

IM P O RTA NT

electrical outlet to prevent tension.

Always check electrical codes for requirements.

Always allow sufcient power cord length to the

Figure 4

E 2

7. Remove the 2 trim screws from each mounting bracket to

4

begin installation.

Note: The mounting brackets come assembled to the side

trims.

8. Open the drawer to properly align brackets to microwave side
rails. See Figure 5.

Bracket

Side rails

Align sides and bottom of the 30"

mounting brackets to the sides and bottom

of the microwave drawer side rails

Figure 5

10. Place side trims on top of the mounting brackets, aligning the
screw holes.

Note: Each side trim is marked "L" and "R" on the backside

to indicate Left and Right.

11. Mount the Left and Right 30" trim extensions using the 4 trim
screws provided. See Figure 7.

9. Using the 4 holes on each bracket as a template, pre-drill
the cabinet using a 1/16" (1.6 mm) bit. Secure the mounting
brackets to cabinet with the 8 bracket crews provided. See
Figure 6.

Figure 6

Figure 7

E 3

MICROWAVE DRAWER FLUSH MOUNT, MEASUREMENTS AND INSTALLATION INSTRUCTIONS

B

C

J

F

I

H

Figure 1

A. 21-5/8" (549.3 mm)
B. 4-11/16" (119.1 mm)
C. 1-3/4" (44.5 mm)
D. 21-7/8" (555.6 mm)
E. 23-5/8" (600.1 mm)

E

F. 16" (406.4 mm)
G. 14-19/32" (370.7 mm)
H. 1-17/32" (38.9 mm) door thickness
I. 15" (381.0 mm) auto drawer opening
J. 4" (101.0 mm)

1. Prepare cabinet opening as shown in Figure 2.

A

Figures 1 and 2 contain many Microwave Drawer measurements
for reference when planning the drawer’s location.

This Microwave Drawer can be installed below any electric or
gas wall oven.

G

D

* Can also be installed using an electrical outlet in an adjacent cabinet

within the area where the provided electrical cord can reach. Power
cord access hole in cabinet should be a minimum 1-1/2" diameter
hole and deburred of all sharp edges.

IM P O RTA NT

Always allow sufcient power cord length to the

electrical outlet to prevent tension.

Always check electrical codes for requirements

Anti-Tip block

A

C

L

Top view

B

F

N

I

G

K

J

I

I

Figure 2

A. 6" (152.4 mm)
B. Suggested electrical outlet

location*

C. Anti-Tip block
D. 5" (127.0 mm)
E. 3-1/2" (88.9 mm)
F. 4" (101.6 mm)
G. 30-5/16" (769.9 mm) min

30-5/8" (777.9 mm) max

H. 14-13/16" (376.2 mm) to bottom

of Anti-Tip block

A

C

D

N

M

E

H

L

I. 1-17/32" (38.9 mm) Refer to

Figure 3 **

J. 23-1/2" (596.9 mm) minimum

depth
K. 22-1/8" (562.0 mm)
L. Floor must support 100 lb (45.4

kg)
M. 16-1/4" (412.8 mm) opening
* See Figure 4C for detail
N. Allow 4-1/8" (104.4 mm)

Mounting cleat

**

Note: the mounting surface
of the finished cleat must sit

(38.9 mm) back from

1-17/32”
the face of the cabinet.

Drawer face

B

Trim

face

C

Figure 3

A. 22-1/8" (596.9 mm) mounting cleat opening width

B. 0"ush

C. 1-17/32" (38.9 mm) front of cleat to cabinet face

Note: For pre-existing 30” cabinet openings that desire a standard

mount,llerpanelswillneedtobeinstalledoneithersideofthecut

out to properly mount the extension kit panels.

E 4

Suggested electrical

outlet location

6. Close drawer to complete oven installation. See Figure 6.

No oven shown

A

Anti-Tip block

B

C

Figure 4

Front view

A. 22-1/8" (562.0 mm) mounting cleat opening width
B. 30-5/16" (770.0 mm) minimum

30-5/8" (777.9 mm) maximum

C. 1/8" (3.2 mm) from opening to top of shelf

2. Place the drawer adjacent to the wall or cabinet opening. Plug
the power supply cord into the electrical outlet.

3. Carefully guide the drawer into the prepared opening. Avoid
contact with the sides of the cutout opening and also pinching
the cord between the oven and the wall.

4. Slide the drawer all the way back until the side rails touch the
cleats mounted in the cabinet opening.

5. Open the drawer. Using the 4 holes on the drawer as a template,
pre-drill the cabinet using a 1/16” (1.6 mm) bit. Secure the
drawer with the 4 screws supplied. See Figure 5.

Figure 6

7. Remove the 2 trim screws from each mounting bracket to
begin installation.

Note: The mounting brackets come assembled to the side

trims.

8. Properly align brackets to microwave side rails. See Figure 7.

Bracket

Side rails

Figure 5

Side
Rail

E 5

Figure 7

Align sides and bottom of the 30"

mounting brackets to the sides and bottom

of the microwave drawer side rails

9. Using the 4 holes on each bracket as a template, pre-drill
the cabinet using a 1/16" (1.6 mm) bit. Secure the mounting
brackets to cabinet with the 8 bracket screws provided. See
Figure 8.

Figure 8

10. Place side trims on top of the mounting brackets, aligning
the screw holes.

Note: Each side trim is marked "L" and "R" on the backside

to indicate Left and Right.

11. Mount the Left and Right 30" trim extensions, using the 4
trim screws provided. See Figure 9.

Figure 9

100 Paragon Drive, Suite #100, Montvale, NJ 07645, USA • 1-800-BE-SHARP (237-4277)

335 Britannia Road East, Mississauga, Ontario, L4Z 1W9, Canada

E 6