Device of this mark is a trademark of
Sharp Corporation.
Plasmacluster is a registered trademark
or a trademark of Sharp Corporation.
(Only for SJ-FP624V, SJ-FP676V)
Thank you very much for buying this SHARP product. Before using your SHARP refrigerator,
please read this operation manual to ensure that you gain the maximum benet from it.
Household use only
WARNING
This refrigerator contains ammable refrigerant (R600a: ■
isobutane) and insulation blowing gas (cyclopentane).
Observe the following rules to prevent ignition and
explosion.
The refrigeration system behind and inside the •
refrigerator contains refrigerant. Do not allow any sharp
objects to come into contact with the refrigeration
system.
Do not use mechanical devices or other means to •
accelerate the defrosting process. (This refrigerator has
adopted automatic defrosting system.)
Do not use electric appliances inside the refrigerator.• Use only the specied parts for the refrigerator •
compartment light.
Do not block the openings on the circumference of the •
refrigerator.
Do not use ammable sprays, such as spray paint near •
the refrigerator. It may cause explosion or re.
If the refrigeration system should get punctured, do not •
touch the wall outlet and do not use open ames. Open
the window and air out the room. Then ask a service
agent approved by SHARP for servicing.
This refrigerator should be disposed appropriately. •
Take the refrigerator to a recycling plant for ammable
refrigerant and insulation blowing gases.
Do not store highly volatile and ammable materials such ■
as ether, petrol, propane gas, aerosol cans, adhesive
agents and pure alcohol etc.
These materials are liable to explode.
Dust deposited on the power plug may cause re. Wipe it ■
off carefully.
Do not attempt to change or modify this refrigerator. This ■
may result in re, electric shock or injury.
Ensure that the refrigerator presents no danger to children ■
while being stored for disposal. (e.g. remove the magnetic
door seals to prevent child entrapment.)
CAUTION
Attention about Power supply:■
Do not use an extension cord or adapter plug.•
Make sure that the power cord has not been damaged •
during installation or moving. If the power plug or cord
is loose, do not insert the power plug. There is a risk of
electric shock or re.
Disconnect from the mains electricity supply by removing •
the mains plug from the electricity supply socket. Do
not remove by pulling the mains lead. This may cause
electric shock or re.
Should the exible supply cord be damaged, it must be •
replaced by a service agent approved by SHARP as a
special cord is required.
Do not touch the compressor unit or its peripheral parts, ■
as they become extremely hot during operation and the
metal edges may cause injury.
Do not touch foods or metal containers in the freezer ■
compartment with your wet hands. This may cause
frostbite.
Do not place bottled and canned drinks in the freezer as ■
they may crack when frozen.
In case of gas leak, ventilate the area by opening a ■
window, etc. Do not touch the refrigerator or the power
outlet.
Do not place objects containing liquid or unsteady objects ■
on top of refrigerator.
This refrigerator is not intended for use by persons ■
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the refrigerator by a person responsible
for their safety. Young children should be supervised to
ensure that they do not play with the refrigerator.
3
4
INSTALLATION
90mm
or more
60mm
or more
60mm
or more
1180 mm
1500 mm
60mm or more
WARNING
Do not install the refrigerator in a damp or wet ■
location as this may cause damage to the insulation
and a leakage. Condensation may also build on the
outer cabinet and cause rust.
Keep adequate ventilation space around the refrigerator.
1
The gure shows the minimum required space for •
installing the refrigerator. The amount of space
around the refrigerator affects the amount of power
consumption.
Insufcient spacing will decrease cooling efciency •
and increase energy consumption. This may reduce
the life of the unit and void warranty.
Free standing type
Remove the 4 screws of the cabinet lower part, and
4
then set the foot cover (supplied inside the refrigerator
compartment) with removed 4 screws.
Screw
(4 screws)
Foot cover
Connect the power plug to a 230/240 volt. 10 amp.
5
power point.
NOTE
Position your refrigerator so that the plug is accessible.•
Keep your refrigerator out of direct sunlight.•
Do not place next to heat generating appliance.•
Do not place directly on the ground. Provide suitable stand. •
If the mains power is switched on when the door is open, the •
door alarm will sound. Close the door to stop the alarm.
Screw
Use the two front adjustable feet, to ensure that the
2
refrigerator is positioned rmly and at on the oor.
Adjustable foot
When right and left doors are not properly aligned, adjust
3
using the adjustable feet.
When the left door is
raised.
When the right door is
raised.
Before using your refrigerator
Clean the inside parts with a cloth soaked in warm water.
If soapy water is used, wipe it off thoroughly with water.
To store large-size bottles, move
the partition all the way back.
Fresh case19.
Ice cube maker 20.
Do not over ll the tray; •
otherwise the ice cubes will be joined
together when frozen.
When the ice cubes are made, •
turn the lever clockwise to empty the
ice into the Ice cube box.
Ice cube box 21.
To prevent damage to the Ice cube box,
do not make ice in the Ice cube box or
pour oil into it.
(2 pcs.)
(2 pcs.)
Partition
Lever
Ice cube box
Magnetic door seals 22.
Eco sign 23.
With the refrigerator door left open, the lamp will slowly
change its color from blue to orange. It shows that the
temperature in the refrigerator is rising.
(Only for SJ-FP624V, SJ-FP676V)
(4 pcs.)
Control panel24.
Deodorising unit
Deodorising catalyst is installed on the routes of cold air. No
operation and cleaning are required.
NOTE
Deodorising unit cannot remove all of the odours thoroughly. •
Wrap the food with strong odours.
If you wish to store large items within
your freezer
You may remove any of the items numbered 6,7,21.
How to remove
To remove the partition, pull it to
the front while pushing the claw.
Claw
Push
Partition
How to set
Insert the four projections into
the upper parts.
5
6
Control panel
SJ-FP624V / SJ-FP676V
SJ-FB624V
Sound OFF indication
This indication shows
sound “OFF”.
Door alarm indication
This indication shows door
alarm “ON”.
Select button
Press to select feature
icon and door alarm signal.
/ button
Press to select feature
ON/OFF or temperature
setting.
(Enter) button
Finalize the setting.
Feature icons
Icons of features in operation
are displayed.
Plasmacluster
Controlling temperature
icons
Refrigerator
compartment
Energy savingFreezer compartment
Vacation mode
Express Freezing
Child lock
Sound ON/OFF
At rst, the sound is set “ON”.•
Use this feature when you want to switch the sound of •
button operation to “ON” or “OFF”.
To set sound “OFF”
Press the button andbutton simultaneously and
continuously for 3 seconds or more.
NOTE
Features start automatically like right gure •
when inserting the power plug. (At rst, only
Door alarm is “ON”).
When there is no operation for approx. •
1 minute the display automatically return to the
standby display. Additionally, the display will
be turned off when there is no operation for 1
minute.
When either of the buttons are pressed, the •
icons will blink once and show the standby
display. When the refrigerator stops with
power failure, the display shows
similarly as before having a power
failure at the time of re-power distribution.
However, when it has a power failure during operation of
Express Freezing, the operation is stopped at the time of
re-power distribution. (Only for SJ-FP624V, SJ-FP676V)
<Standby display>
To set sound “ON”
Press the button andbutton simultaneously and
continuously for 3 seconds or more again.
Beep beep beep
It shows the sound “OFF”.
The indication will disappear.
Beep beep beep
OPERATION
Plasmacluster
(Only for SJ-FP624V, SJ-FP676V)
The ionizer inside your refrigerator releases clusters of ions,
which are collective masses of positive and negative ions,
into the refrigerator compartment.
These ion clusters inactivate airborne mould fungus.
mould
fungus
To start operation
Select “Plasmacluster icon”.
1
Flashing
Select “ON”.
2
Energy Saving
(Only for SJ-FP624V, SJ-FP676V)
Use this feature when you want to switch the appliance to
energy-saving operation.
To start operation
Select “Energy saving” icon.
1
Flashing
Select “ON”.
2
Finalize the setting.
3
To cancel operation
It is the same method as starting operation.
Select “OFF” in step 2.
NOTE
There may be a slight odour in the refrigerator. This is the •
smell of ozone generated by the ionizer. The amount of
ozone is minimal, and quickly decomposes in the refrigerator.
Finalize the setting.
3
To cancel operation
It is the same method as starting operation.
Select “OFF” in step 2.
NOTE
While this feature is operating, the inside temperature of the •
refrigerator and freezer compartment will be higher than the
preset temperature by about 1°C(refrigerator) and about
2°C(freezer). This is the guide under the condition of the
preset temperature 3°C(refrigerator) and -18°C(freezer). The
display of preset temperature will not be changed.
The efciency of power saving depends on the usage •
environment (controlling temperature, ambient temperature,
frequency of opening or closing the door, amount of food).
Cancel this feature when you feel the beverages are not •
cooled enough or ice making takes time.
7
8
Vacation mode
(Only for SJ-FP624V, SJ-FP676V)
Use this feature when going on a trip or leaving the house
for a long time.
Express Freezing
(Only for SJ-FP624V, SJ-FP676V)
High-quality frozen foods can be made using this feature
and is convenient for home-freezing.
To start operation
Select “Vacation mode” icon.
1
Select “ON”.
2
Finalize the setting.
3
Flashing
To start operation
Select “Express freezing” icon.
1
Select “ON”.
2
Finalize the setting.
3
Flashing
To cancel operation
It is the same method as starting operation.
Select “OFF” in step 2.
NOTE
The temperature inside the refrigerator compartment will be •
adjusted to about 10°C.
Food storage period in the refrigerator compartment becomes •
approx.1/2-1/3 of normal operation. Please utilize only when
there is no perishable food.
Temperature of refrigerator compartment cannot be modied. •
(“10°C” is indicated on the display.)
To cancel operation
It is the same method as starting operation.
Select “OFF” in step 2.
NOTE
Express Freezing ends automatically in about 2 hours. •
(The icon will disappear.)
Large foods cannot be frozen in a single operation.•
Express Freezing may require more than 2 hours in the case •
operation overlaps with defrosting as operation is started after
defrosting is completed.
Avoid opening the door as much as possible during operation •
of this feature.
Child Lock
(Only for SJ-FP624V, SJ-FP676V)
Button operation of the control panel will be locked. Use this
feature to prevent the panel from being used unintentionally
by children or someone.
Door Alarm
At rst, door alarm is set “ON”.•
When the refrigerator door is left open, the door alarm will •
sound.
The door alarm will sound in 1 minute after opening the •
door and again after 1 minute (once in each case).
If the door is left open for approx. 3 minutes, the alarm will •
sound continuously.
To start operation
Select “Child lock” icon.
1
Select “ON”.
2
Finalize the setting.
3
Flashing
To cancel operation
Select the door alarm indication like the below gure.
1
Flashing
Select “OFF”.
2
Finalize the setting.
3
At standby display
To cancel operation
It is the same method as starting operation.
Select “OFF” in step 2.
The indication will
disappear.
To start operation
It is the same method as canceling operation.
Select “ON” in step 2.
Flashing
Door alarm
indication
At standby display
It shows Door
alarm “ON”.
9
10
Controlling Temperature
The refrigerator controls its temperature automatically. However, if needed, adjust the temperature as follows.
Refrigerator compartment
Adjustable between 0°C and 6°C in steps of 1°C.
Select icon.
1
The display shows the current preset temperature.
Flashing
Set the temperature.
2
[
: increase, : decrease ]
Finalize the setting.
3
Freezer compartment
Adjustable between -13°C and -21°C in steps of 1°C.
Select icon.
1
The display shows the current preset temperature.
Flashing
Set the temperature.
2
[
: increase, : decrease ]
Finalize the setting.
3
Advanced Setting of Freezer / Refrigerator compartment
The temperature of freezer compartment and refrigerator compartment can be adjusted in steps of 0.5 °C by following steps
to 3 below.
1
Refrigerator compartment
Select
1.
Press
2.
The current preset temperature on the display will be changed to 3.0 °C.
(The display will be indicated like right gure.)
Adjust the temperature in the same way as steps
3.
Follow steps
icon.
button continuously for 3 seconds or more.
to 2 again if you want to adjust the temperature in steps of 1°C.
1
Freezer compartment
Select
1.
Press
2.
The current preset temperature on the display will be changed to -18.0 °C.
(The display will be indicated alternately like right gure.)
Adjust the temperature in the same way as steps
3.
Follow steps
icon.
button continuously for 3 seconds or more.
to 2 again if you want to adjust the temperature in steps of 1°C.
1
Beep beep beep
2 to 3 above.
Beep beep beep
2 to 3 above.
STORING FOOD
Small foods
Juice etc.
Bottles etc.
Frozen foods
(Small size)
Frozen foods
(Big size)
Vegetables
Fruits
Dairy products
Small foods
Eggs etc.
Bottles etc.
(Big size)
Meat, Fish, Poultry etc.
This section is not suitable ●
to store vegetables as they
may freeze.
Refrigeration reduces the rate of food spoilage.
To maximize the shelf life of perishable food products,
ensure that the food is of the freshest possible quality.
The following is a general guide to help promote longer food
storage.
Fruit / Vegetables
To minimize moisture loss, fruit and vegetables should be
loosely enclosed in a plastic material (e.g. wrap, bags) and
place in the vegetable crisper or the fruit case.
If you store a lot of vegetables, dew may form. This has no
effect on the operation or the performance. Use a dry cloth
to remove the dew.
Dairy Products & Eggs
Most dairy products have a use by date on the outer •
packaging which informs the recommended temperature
and shelf life of the product.
Eggs should be stored in the Egg tray.•
Meats / Fish / Poultry
Place on a plate or dish and cover with paper or plastic •
wrap.
For larger cuts of meat, sh, or poultry, place to the rear of •
the shelves.
Ensure all cooked food is wrapped securely or placed in an •
airtight container.
NOTE
Evenly place the food on the shelves •
to allow the cooling air to circulate
efciently.
Hot foods should be cooled before •
storing. Storing hot foods increases
the temperature in the unit and
increases the risk of food spoilage.
Do not block the outlet and inlet of the •
cool air circulating circuit with foods
or containers; otherwise the foods will
not be evenly cooled throughout the
refrigerator.
Keep the door securely closed.•
IN
OUT
Do not place food directly in front of cold air
outlet. This may lead to the food freezing.
For best freezing
Quality of foods should be fresh.•
Freeze small quantities of food at a time to freeze them •
quickly.
Food should be properly sealed, sealed tightly or covered.•
Evenly place the food in the freezer.•
Label bags or containers to keep an inventory of frozen •
food.
11
12
CARE AND CLEANING
WARNING
Unplug the refrigerator rst to prevent electric shock. ■
Do not splash water directly on the outer cabinet or ■
the interior. This may lead to rusting and deterioration
of the electrical insulation.
IMPORTANT
To prevent cracking on inside surfaces and plastic
components, follow these tips.
Wipe any food oils adhered to plastic components.•
Some household chemicals may cause damage, so use •
only diluted washing-up liquid (soapy water).
If undiluted detergent is used or soapy water is not wiped •
off thoroughly, cracking of plastic parts can result.
Wipe any spills from the refrigerator immediately as acid or alkaline •
in the food can cause cracking and staining of plastic parts.
Remove the accessories e.g. shelves from the cabinet
1
and door. Wash them in warm soapy dishwashing water;
rinse in clean water and dry.
Clean the inside with a cloth soaked in warm soapy
2
dishwashing water. Then, use cold water to wipe off
soapy water.
Wipe the exterior with a soft cloth each time it is soiled.
3
Clean the Magnetic door seal with a toothbrush and
4
warm soapy dishwashing water.
Wipe the control panel with the dry cloth.
5
NOTE
Do not use hot water, household cleaning powders, creams or •
spray-on cleaning products, or any other cleaning products such
as mineral turpentine, methylated spirits, thinners, petrol etc.
These may damage your refrigerator and may void any warranty.
If the power supply is disconnected, please wait for at least •
5 minutes before re-connecting power.
The glass shelves weigh approximately 3 kg each. Hold rmly •
when removing from the cabinet or carrying.
Do not drop objects inside the refrigerator or strike the inner •
wall. This may cause the inner surface to crack.
When the compartment light is blown
Contact the service agent approved by SHARP to request a
replacement compartment light. The compartment light is not
to be removed other than by qualied service personnel.
When transporting
Wipe up water in the evaporating pan. Before wiping up •
the water, wait more than 1 hour after pulling out the plug
because refrigeration cycle equipment is extremely hot.
(The evaporating pan is located on the rear of the product.)
Evaporating pan
The casters allow the refrigerator to •
move back and forth.
Casters
Carry the refrigerator by holding the handles located on the •
rear and bottom.
Defrosting
Defrosting is fully automatic due to a unique energy saving
system.
Tips for saving energy
Keep the ventilation space as much as possible around ■
the refrigerator.
Keep your refrigerator out of direct sunlight, and do not ■
place next to heat generating appliance.
Open your refrigerator door as briey as possible.■
Hot foods should be cooled before storing. ■
Place the food evenly on the shelves to allow the cooling ■
air to circulate efciently.
Switching off your refrigerator
If the refrigerator needs to be switched off for an extended
period, the following steps should be taken to reduce the
growth of mould:
Remove all food.1.
Remove the power plug from the power point.2.
Clean and dry the interior thoroughly.3.
Ensure that all the doors are wedged open slightly for air 4.
circulation.
BEFORE YOU CALL FOR SERVICE
Before you call for service, check the following points.
ProblemSolution
The outside of the cabinet is hot
when touched.
When there is refrigerator noise.It is normal for the refrigerator to produce the following sounds.
Frosting or condensation
generation occurs inside or
outside the refrigerator.
The foods in the refrigerator
compartment freeze.
Noticeable odours.Wrapping is required for food with strong odours.•
This is normal. The hot pipe is in the cabinet in order to prevent condensation
generation.
Loud noise produced by the compressor when operation starts •
--- Sound becomes quieter after a while.
Loud noise produced once a day by the compressor •
--- Operating sound produced immediately after automatic defrost operation.
Sound of owing uid (gurgling sound, zzing sound) •
--- Sound of refrigerant owing in pipes (sound may become louder from time to time).
Cracking or crunching sound, squeaking sound •
--- Sound produced by expansion and contraction of inner walls and internal parts
during cooling.
This may occur in one of the following cases. Use a wet cloth for wiping frost and a dry
cloth for wiping condensation.
When the ambient humidity is high.•
When the door is frequently opened and closed.•
When food containing plenty of moisture is stored. (Wrapping is required.)•
Is the refrigerator operated for a long time with refrigerator temp. control set at 0°C?•
Is the refrigerator operated for a long time with freezer temp. control set at -21°C?•
Low ambient temperature may cause food to freeze even if refrigerator temp. control is •
set to MIN.
If you still require service contact your SHARP Approved Service Centre.
SHARP Approved Service Centre locations can be found in the Support area of our website:
Australia : http://www.sharp.net.au
New Zealand : http://www.sharp.net.nz
13
14
SPECIFICATION
Rated voltage (V~)
Rated frequency (Hz)
Rated current (A)
Rated input of heating systems (W)
Defrosting input (W)
Refrigerant
Charge (g)
Rated storage volume (L)
Rated gross volume (L)
Climate class
Insulation blowing gas
Group (AS / NZS 4474.1)
Net weight (kg)
Outer dimensions
(mm)
220 - 240
SJ-FP624V
50
1.3 - 1.4
173 - 206
173 - 206
R600a
T
83
Cyclo pentane
5B
552
624
104
1720
892
771
220 - 240
SJ-FB624V
50
1.3 - 1.4
173 - 206
173 - 206
R600a
T
83
Cyclo pentane
5B
552
624
104
1720
892
771
220 - 240
SJ-FP676V
50
1.3 - 1.4
173 - 206
173 - 206
R600a
T
83
Cyclo pentane
5B
600
676
107
1830
892
771
Height
Width
Depth
15
SHARP CORPORATION OF AUSTRALIA PTY.LTD.
A. B. N. 40 003 039 405
1 HUNTINGWOOD DRIVE, HUNTINGWOOD, N.S.W. 2148
P.O.BOX 6827, BLACKTOWN. N.S.W. 2148
SHARP CORPORATION OF NEW ZEALAND LIMITED
59 HUGO JOHNSTON DRIVE P.O. BOX 12244, PENROSE, AUCKLAND
Printed in Thailand
TINS-B352CBRZ 12HK TH
1
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.