MEASURE CARRIED OUT TO COMPLY WITH NOISE STANDARDS.
1.Model Name:SF-1016/2116/2118 (only for machines bound for Taiwan.)
2.General:The changes described below have been carried out as a measure to establish
No. : S-208
compliance with Taiwan noise standards.
3.Description:<1> A change has been carried out in the capacitors and in the resistors used in the AC
circuit PWB.
The capacitor (C204) has been changed from 0.22 µF to 6 µF.
VCFYEG2EA224M → RC-FZ0351FCZZ
The resistor (R203) has been changed from 1 MΩ to 220 kΩ.
VRD-HT2EY105J → VRD-HT2EY224J
In accordance with the changes described above, the part code for the AC circuit PWB
has also been changed.
<2> The addition of a grounding shaft and a ground wire has been carried out. (This
change has been carried out only on models SF-1016 and SF-2016.) This change has
been carried out as a measure to improve the grounding performance of the
reinforcement plate in the base plate unit.
Ground wire
M3 × 10 three-point screw
Grounding shaft
Ground wire
SHARP CORPORATIONReprography Division
1/5
Green
C
<3> The addition of a gasket has been carried out as a measure to improve the
performance of the connecting ground for the upper and lower frames.
Gasket
Lower frame R AS
Gasket
Gasket
attachment
sheet
Suction fun UN attachment
section
attachment
sheet
Lower frame R AS
Gasket A
Gasket B
Attached to the lower frame R
and W base plate rear frame.
The attachment of gasket B has been
carried out only on model SF-2118.
<4> The addition of a ferrite core and an MM interface harness has been carried out on
each of the harnesses.
HV trans
High voltage UN
(RTRNZ0508FCZ2)
GR
Beads band
(LBNDJ0015FCZZ)
High voltage harness
(DHAI-2423FCZZ)
1 pin connector
One touch ferrite core
(RCORF6661RCZZ)
2/5
BC transistor
MCFB
Wire saddle
(LHLDW1269FCZZ)
Optical main harness
Upper frame
Optical UN
Mirror motor
High voltage UN
6 Pin white
connector
3 Pin Blue
connector
2 Pin white connector
MM
3 Pin white
connector
interface
connector
MM interface harness
(DHAI-2568FCZZ)
Added ferrite core
(only for models SF-1016 and 2116)
RCORF0026FCZZ
Operations panel
10 Pin
white connector
6 Pin white connector
(only for Japan B and H ver B)
Operation main harness
(DHAI-2404FCZZ-11)
Added ferrite core
(RCORF0026FCZZ) (only for model SF-2118)
6 pin black
connector
Original copy detection
(only for Japan B and H ver B)
11 Pin white connector
11 Pin connector
To process unit
3/5
<5> The additon of a rubber sheet to the drive unit and the rear cabinet has been
carried out. This change has been carried out as a measure to prevent leaking.
Drive unit skating B
(CFRM-0836FC72)
Leak prevention sheet C
Motor frame
Clear plastic
(PSHEZ4462FCZZ)
Leak prevention sheet B
(PSHEZ4461FCZZ)
Rear cabinet back side
Y standard
Vertical standard aluminium
sheet edge section
Depress to insert
Leak prevention sheet D
(PSHEZ4463FCZZ)
X standard
(Machine)
Motor frame UN
Leak prevention sheet A
(PSHEZ4460FCZZ)
Horizontal standard rib
<6> The addition of a capacitor between DATA 1 and the GND has been carried out in
the main PWB (only for model SF-2118).
Capacitor: VCKYPA1HB103K