Sharp R-43040D, R-430DW, R-430DQ, R-440DK, R-440DW Service Manual

Download

SERVICE MANUAL

S70M147R430DE

MICROWAVE OVEN

R-430DK R-430DW R-430DQ R-440DK R-440DW

MODELS

R-430DW R-430DQ R-440DK R-440DW

R-430DK

R-430D

TABLE OF CONTENTS

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO

AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY....................INSIDE FRONT COVER

BEFORE SERVICING ......................................................................................................INSIDE FRONT COVER

WARNING TO SERVICE PERSONNEL............................................................................................................... 1

MICROWAVE MEASUREMENT PROCEDURE................................................................................................... 2

FOREWORD AND WARNING ............................................................................................................................. 3

PRODUCT SPECIFICATIONS ............................................................................................................................. 4

GENERAL INFORMATION ................................................................................................................................. 4

OPERATION ........................................................................................................................................................ 6

TROUBLESHOOTING GUIDE ........................................................................................................................... 10

TEST PROCEDURE .......................................................................................................................................... 12

TOUCH CONTROL PANEL ............................................................................................................................... 21

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ............................................................... 32

PICTORIAL DIAGRAM....................................................................................................................................... 38

POWER UNIT CIRCUIT ..................................................................................................................................... 40

LSI UNIT CIRCUIT ............................................................................................................................................. 41

PRINTED WIRING BOARD................................................................................................................................ 44

PARTS LIST....................................................................................................................................................... 45

PACKING AND ACCESSORIES ........................................................................................................................ 50

In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specified should be used.

WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)

Page

SHARP ELECTRONCS CORPORATION

Service Headquarters: Sharp Plaza, Mahwah, New Jersey, 07430-2135

This document has been published to be used for after sales service only. The contents are subject to change without notice.

R-430DK R-430DW R-430DQ R-440DK R-440DW

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other

microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.

compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.

(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave

generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.

(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be

performed on each oven prior to release to the owner.

BEFORE SERVICING

Before servicing an operative unit, perform a microwave emission check as per the Microwave Measurement Procedure outlined in this service manual. If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS CORPORATION immediately @1-800-237-4277.

If the unit operates with the door open, service person should 1) tell the user not to operate the oven and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's Center for Devices and Radiological Health immediately.

Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit until the oven has been brought into compliance.

W ARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts fatal, electrical shock.

(Example) High Voltage Capacitor, High Voltage Power Trans-

former, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..

Read the Service Manual carefully and follow all instructions.

may result in a severe, possibly

Don't Touch ! Danger High Voltage

R-430DK R-430DW R-430DQ R-440DK R-440DW

Before Servicing

1. Disconnect the power supply cord , and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

WARNING:RISK OF ELECTRIC SHOCK.

DISCHARGE THE HIGH-VOLTAGE CAPACITOR BEFORE SERVICING.

The high-voltage capacitor remains charged about 60 seconds after the oven has been switched off. Wait for 60 seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an insulated screwdriver.

Whenever troubleshooting is performed the power supply must be disconnected. It may in, some cases, be necessary to connect the power supply after the outer case has been removed, in this event,

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the leads to the primary of the power transformer.

5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.

6. After that procedure, reconnect the power supply cord.

When the testing is completed,

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Reconnect the leads to the primary of the power transformer.

5. Reinstall the outer case (cabinet).

6. Reconnect the power supply cord after the outer case is installed.

7. Run the oven and check all functions.

After repairing

1. Reconnect all leads removed from components during testing.

2. Reinstall the outer case (cabinet).

3. Reconnect the power supply cord after the outer case is installed.

4. Run the oven and check all functions.

Microwave ovens should not be run empty. To test for the presence of microwave energy within a cavity, place a cup of cold water on the oven turntable, close the door and set the power to HIGH and set the microwave timer for two (2) minutes. When the two minutes has elapsed (timer at zero) carefully check that the water is now hot. If the water remains cold carry out Before Servicing procedure and re-examine the connections to the component being tested.

When all service work is completed and the oven is fully assembled, the microwave power output should be checked and a microwave leakage test should be carried out.

R-430DK R-430DW R-430DQ R-440DK R-440DW

MICROWAVE MEASUREMENT PROCEDURE

A. Requirements:

1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external surface of the oven.

2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission in excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.

B. Preparation for testing: Before beginning the actual measurement of leakage, proceed as follows:

1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.

Important: Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.

2) Place the oven tray in the oven cavity.

3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5oC (68oF) in the center of the oven cavity. The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and made of an electrically nonconductive material such as glass or plastic. The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage is measured accurately.

4) Set the cooking control on Full Power Cooking Mode.

5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed, replace it with 275 ml of cool water.

C. Leakage test:

Closed-door leakage test (microwave measurement)

1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.

2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on the meter.

3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal has been breached (eg., around the switches, indicator, and vents). While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed latch assembly.

4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2, and that the secondary interlock switch does turn the oven OFF before any door movement.

NOTE: After servicing, record data on service invoice and microwave leakage report.

SERVICE MANUAL

MICROWAVE OVEN

R-430DK/DW/DQ

R-440DK/DW

FOREWORD

PRODUCT DESCRIPTION

GENERAL INFORMATION

R-430DK R-430DW R-430DQ R-440DK R-440DW

This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service Information for the SHARP MICROWAVE OVENS, R-430DK, R-430DW, R-430DQ, R-440DK & R-440DW.

It is recommended that service personnel carefully study the entire text of this manual so that they will be qualified to render satisfactory customer service.

Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and microwave radiation hazard.

WARNING

Never operate the oven until the following points are ensured: (A) The door is tightly closed. (B) The door brackets and hinges are not defective. (C) The door packing is not damaged. (D) The door is not deformed or warped. (E) There is no other visible damage with the oven.

Servicing and repair work must be carried out only by trained service personnel.

DANGER

Certain initial parts are intentionally not grounded and present a risk of electrical shock only during servicing. Service personnel - Do not contact the following parts while the appliance is energized; High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness; If provided, Vent Hood, Fan assembly, Cooling Fan Motor.

OPERATION

TROUBLESHOOTING GUIDE AND TEST PROCEDURE

TOUCH CONTROL PANEL

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

WIRING DIAGRAM

PARTS LIST

All the parts marked “*” on parts list are used at voltages more than 250V.

Removal of the outer wrap gives access to voltage above 250V.

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH,

NEW JERSEY 07430-2135

R-430DK R-430DW R-430DQ R-440DK R-440DW

SPECIFICATION

ITEM DESCRIPTION

Power Requirements 120 Volts / 13.8 Amperes/1650Watts

60 Hertz Single phase, 3 wire grounded

Power Output 1200 watts (IEC-705 TEST PROCEDURE)

Operating frequency of 2450MHz

Case Dimensions Width 21-21/32"

Height 12-3/8" Depth 18-7/16"

Cooking Cavity Dimensions Width 15-23/32"

1.6 Cubic Feet Height 9-21/32" Depth 17-7/8" Tray Size 14-1/8"

Control Complement Touch Control System

Clock ( 1:00 - 12:59 ) Timer (0 - 99 min. 99 seconds)

Microwave Power for Variable Cooking Repetition Rate;

P-HI ................................................. Full power throughout the cooking time

P-90....................................................................approx. 90% of Full Power

P-80....................................................................approx. 80% of Full Power

P-70....................................................................approx. 70% of Full Power

P-60....................................................................approx. 60% of Full Power

P-50....................................................................approx. 50% of Full Power

P-40....................................................................approx. 40% of Full Power

P-30....................................................................approx. 30% of Full Power

P-20....................................................................approx. 20% of Full Power

P-10....................................................................approx. 10% of Full Power

P-0.....................................................No power throughout the cooking time

R-430DK Sensor Cooking Pads, Breakfast Bar pads, Lunch on the run pad, One R-430DW Dish Dinner pad, Super Defrost pad, MINUTE PLUS pad, Compu R-430DQ Defrost pad, Beverage Center Pad, Number Selection Pad, Kitchen Timer Pad, Clock pad, Power Level Pad, Stop/Clear Pad, Start Touch Pad. R-440DK R-440DW START pad, ONE TOUCH SENSOR pads 6 X 6 NO GUESS

Beverage Center pad, Defrost pad, Set Up pad

Cavity Light Yes Safety Standard UL Listed FCC Authorized

DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J

TOUCH SCREEN, MINUTE PLUS pad, STOP/CLEAR pad

COOKING pads More From Your Microwave pad

GENERAL INFORMATION

GROUNDING INSTRUCTIONS

This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.

WARNING: Improper use of the grounding plug can result in a risk of electric shock.

Electrical Requirements The electrical requirements are a 120 volt 60 Hz, AC only, 15 or 20 amp. fused electrical supply. It is recommended that a separate circuit serving only this appliance be provided. When installing this appliance, observe all applicable codes and ordinances. A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord. Where a two-pronged wall-receptacle is encountered, it is the personal responsibility and obligation of the customer to contact a qualified electrician and have it replaced with a properly grounded three-pronged wall receptacle or have a grounding

adapter properly grounded and polarized. If the extension cord must be used, it should be a 3-wire, 15 amp. or higher rated cord. Do not drape over a countertop or table where it can be pulled on by children or tripped over accidentally.

CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR RE-

MOVE THE ROUND GROUNDING PRONG FROM THIS PLUG.

R-430DK R-430DW R-430DQ R-440DK R-440DW

1. One touch door open button. Push to open door.

2. Door latches. The oven will not operate unless the door is securely closed.

3. Removable turntable support.

4. Removable turntable. The turntable will rotate clockwise or counterclockwise.

5. Oven lamp. It will light when oven is operating or door is opened.

6. Oven door with see-through window.

7. Ventilation openings. (Rear)

8. Auto-Touch control panel.

9. Time display: Digital display, 99 minutes 99 seconds.

OVEN DIAGRAM

10.Coupling.

11.Wave guide cover.

12.Power supply cord

TOUCH CONTROL PANEL

R-430D R-440D

R-430DK R-430DW R-430DQ R-440DK R-440DW

OPERATION

DESCRIPTION OF OPERATING SEQUENCE

The following is a description of component functions during oven operation.

OFF CONDITION

Closing the door activates the door sensing switch and secondary interlock switch. (In this condition, the monitor switch contacts are opened.) When oven is plugged in, 120 volts A.C. is supplied to the control unit. (Figure O-1).

1. The display will show flashing"SHARP SIMPLY PRESS CLEAR AND PRESS CLOCK" To set any program or set the clock, you must first touch the STOP/CLEAR pad. The display will clear, and " : " will appear.

COOKING CONDITION

Program desired cooking time by touching the NUMBER pads. Program the power level by touching the POWER LEVEL pad and then a Number pad. When the START pad is touched, the following operations occur:

1. The contacts of relays are closed and components connected to the relays are turned on as follows. (For details, refer to Figure O-2)

the secondary interlock switch and primary interlock relay and is mechanically associated with the door so that it will function in the following sequence.

(1) When the door opens from the closed position, the

primary interlock relay (RY2) and secondary interlock switch open their contacts. And contacts of the relay (RY1) remains closed. Then the monitor switch contacts close.

(2) When the door is closed from the open position, the

monitor switch contacts open first. Then the contacts of the secondary interlock switch and door sensing switch

close. And contacts of the relay (RY1) open. If the secondary interlock switch and primary interlock relay (RY2) fail with the contacts closed when the door is opened, the closing of the monitor switch contacts will form a short circuit through the monitor fuse, secondary interlock switch, relay (RY1) and primary interlock relay (RY2), causing the monitor fuse to blow.

POWER LEVEL P-0 TO P-90 COOKING

When Variable Cooking Power is programmed, the 120 volts A.C. is supplied to the power transformer intermittently through the contacts of relay (RY-2) which is operated by the control unit within a 32 second time base. Microwave power operation is as follows:

RELAY CONNECTED COMPONENTS RY-1 oven lamp/turntable motor/fan motor RY-2 power transformer

2. 120 volts A.C. is supplied to the primary winding of the power transformer and is converted to about 3.3 volts A.C. output on the filament winding, and approximately 2370 volts A.C. on the high voltage winding.

3. The filament winding voltage heats the magnetron filament and the H.V. winding voltage is sent to a voltage doubler circuit.

4. The microwave energy produced by the magnetron is channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed to be cooked.

5. Upon completion of the cooking time, the power transformer, oven lamp, etc. are turned off, and the generation of microwave energy is stopped. The oven will revert to the OFF condition.

6. When the door is opened during a cook cycle, the monitor switch, door sensing switch, secondary interlock switch, relay (RY1) and primary interlock relay are activated with the following results. The circuits to the turntable motor, the cooling fan motor, and the high voltage components are de-energized, the oven lamp remains on, and the digital read-out displays the time still remaining in the cook cycle when the door was opened.

7. The monitor switch electrically monitors the operation of

VARI-MODE ON TIME OFF TIME Power 10(P-HI) 32 sec. 0 sec.

(100% power) Power 9(P-90) 30 sec. 2 sec.

(approx. 90% power) Power 8(P-80) 26 sec. 6 sec.

(approx. 80% power) Power 7(P-70) 24 sec. 8 sec.

(approx. 70% power) Power 6(P-60) 22 sec. 10 sec.

(approx. 60% power) Power 5(P-50) 18 sec. 14 sec.

(approx. 50% power) Power 4(P-40) 16 sec. 16 sec.

(approx. 40% power) Power 3(P-30) 12 sec. 20 sec.

(approx. 30% power) Power 2(P-20) 8 sec. 24 sec.

(approx. 20% power) Power 1(P-10) 6 sec. 26 sec.

(approx. 10% power) Power 0(P-0) 0 sec. 32 sec.

(0% power)

Note: The ON/OFF time ratio does not correspond with the

percentage of microwave power, because approx. 2 seconds are needed for heating of the magnetron filament.

SENSOR COOKING CONDITION

Using the SENSOR function, food is cooked without figuring time, power level or quantity. When the oven senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining cooking time and power level needed for best results. When the food is cooked, water vapor is developed. the sensor "senses" the vapor and its resistance increase gradually. When the resistance reaches the value set according to the menu, supplementary cooking is started. The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI. An example of how sensor works: (Potatoes)

1. Potatoes at room temperature. Vapor is emitted very slowly.

R-430DK R-430DW R-430DQ R-440DK R-440DW

2. The coil of shut-off relay (RY-1) is energized, the turntable motor are turned on, but the power transformer is not turned on.

3. After about 16 seconds, the cook relay (RY-2) is energized. The power transformer is turned on, microwave energy is produced and first stage is started. The 16 seconds is the cooling time required to remove any vapor from the oven cavity and sensor.

NOTE: During this first stage, do not open the door or touch

STOP/CLEAR pad.

4. When the sensor detects the vapor emitted from the food, the display switches over to the remaining cooking time and the timer counts down to zero. At this time, the door may be opened to stir, turn or season food.

5. When the timer reaches zero, an audible signal sounds. The shut-off relay and cook relay are de-energized and the power transformer, oven lamp, etc. are turned off.

6. Opening the door or touching the STOP/CLEAR pad, the time of the day will reappear on the display and the oven will revert to an OFF condition. When the timer reaches zero, an audible signal sounds.

2.Heat Potatoes. Moisture and humidity is emitted very rapidly. You can smell the aroma as it cooks.

3.Sensor detects moisture and humidity and calculates cooking time and variable power.

Cooking Sequence.

1. Touch one of the SENSOR pads. NOTE: The oven should not be operated on sensor

immediately after plugging in the unit. Wait two minutes before cooking on SENSOR.

R-430DK R-430DW R-430DQ R-440DK R-440DW

NOTE: CONDITION OF OVEN

1. DOOR CLOSED

2. CLOCK APPEARS ON DISPLAY

SCHEMATIC

120V AC 60 Hz

MAGNETRON TEMP. FUSE

GRN

CAVITY TEMP. FUSE

MONITOR FUSE 20A

CONTROL UNIT

OL FM

OVEN LAMP

SECONDARY INTERLOCK SWITCH

(RY-1)

TTM

TURNTABLE MOTOR

COM.

Figure O-1 Oven Schematic - Off Condition

SCHEMATIC

NOTE: CONDITION OF OVEN

1. DOOR CLOSED

2. COOKING TIME PROGRAMMED

3. VARIABLE COOKING CONTROL "HIGH"

4. "START" PAD TOUCHED

FAN MOTOR

N.O.

COM.N.O.

B1 B2

(RY-2)

PRIMARY INTERLOCK RELAY

DOOR SENSING SWITCH

AH SENSOR

N.C.

COM.

MONITOR SWITCH

CAPACITOR 1.0µF AC 2300V

POWER TRANSFORMER

H.V. RECTIFIER

MAGNETRON

120V AC 60 Hz

MAGNETRON TEMP. FUSE

GRN

CAVITY TEMP. FUSE

MONITOR FUSE 20A

CONTROL UNIT

OL FM

OVEN LAMP

SECONDARY INTERLOCK SWITCH

(RY-1)

TTM

Figure O-2 Oven Schematic - Cooking Condition

TURNTABLE MOTOR

COM.

FAN MOTOR

N.O.

COM.N.O.

B1 B2

(RY-2)

PRIMARY INTERLOCK RELAY

DOOR SENSING SWITCH

AH SENSOR

N.C.

COM.

MONITOR SWITCH

CAPACITOR 1.0µF AC 2300V

POWER TRANSFORMER

H.V. RECTIFIER

MAGNETRON

DESCRIPTION AND FUNCTION OF COMPONENTS

R-430DK R-430DW R-430DQ R-440DK R-440DW

DOOR OPEN MECHANISM

The door is opened by pushing the open button on the control panel, refer to the Figure D-1. When the open button is pushed, the open button pushes up the switch lever, and then the switch lever pushes up the latch head. The latch heads are moved upward and released from latch hook. Now the door will open.

Latch Heads

Door

Switch Lever

Door Sensing Switch

Monitor Switch

Secondary Interlock Switch

Figure D-1. Door Open Mechanism

DOOR SENSING AND SECONDARY INTERLOCK SWITCHES

The secondary interlock switch is mounted in the lower position of the latch hook and the door sensing switch in the primary interlock system is mounted in the upper position of the latch hook. They are activated by the latch heads on the door. When the door is opened, the switches interrupt the power to all high voltage components. A cook cycle cannot take place until the door is firmly closed thereby activating both interlock switches. The primary interlock system consists of the door sensing switch and primary interlock relay located on the control circuit board.

MONITOR SWITCH

The monitor switch is activated (the contacts opened) by the latch head on the door while the door is closed. The switch is intended to render the oven inoperative, by means of blowing the monitor fuse, when the contacts of the primary interlock relay (RY2) and secondary interlock switch fail to open when the door is opened.

open, the monitor fuse blows simultaneously with closing of the monitor switch contacts.

CAUTION: BEFORE REPLACING A BLOWN MONITOR

FUSE TEST THE DOOR SENSING SWITCH, PRIMARY INTERLOCK RELAY (RY2), RELAY (RY1), SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH FOR PROPER OPERATION. (REFER TO CHAPTER "TEST PROCEDURE").

NOTE: MONITOR FUSE AND MONITOR SWITCH ARE

REPLACED AS AN ASSEMBLY.

TURNTABLE MOTOR

The turntable motor rotates the turntable located on the bottom of the oven cavity, so that the foods on the turntable cook evenly during cooking. The turntable may turn in either direction.

COOLING FAN MOTOR

The cooling fan motor drives a blade which draws external cool air. This cool air is directed through the air vanes surrounding the magnetron and cools the magnetron. This air is channelled through the oven cavity to remove steam and vapors given off from the heating foods. It is then exhausted through the exhausting air vents at the oven cavity.

MONITOR FUSE

1. The monitor fuse blows when the contacts (COM-NO) of the primary interlock relay (RY2) and secondary interlock switch remain closed with the oven door open and when the monitor switch closes.

2. If the wire harness or electrical components are shortcircuited, this monitor fuse blows to prevent an electric shock or fire hazard.

CAVITY TEMPERATURE FUSE

The cavity temperature fuse located on the top of the oven cavity, is designed to prevent damage to the oven by fire. If the food load is overcooked, by either error in cook time or defect in the control unit, the cavity temperature fuse will open. Under normal operation, the cavity temperature fuse remains closed. However, when abnormally high temperatures are reached within the oven cavity, the cavity temperature fuse will open at 302oF(150oC) causing the oven to shut down. NOTE: This is fuse. It does not reset.

Functions:

1. When the door is opened, the monitor switch contact close (to the ON condition) due to their being normally closed. At this time the primary interlock relay (RY2) and secondary interlock switch are in the OFF condition (contacts open) due to their being normally open contact switches.

2. As the door goes to a closed position, the monitor switch contacts are first opened and then the door sensing switch and the secondary interlock switch contacts close. (On opening the door, each of these switches operate inversely.)

3. If the door is opened, and the primary interlock relay (RY2) and secondary interlock switch contacts fail to

MAGNETRON TEMPERATURE FUSE

The magnetron temperature fuse located near the magnetron is designed to prevent damage to the magnetron if an over heated condition develops in the tube due to cooling fan failure, obstructed air guide, dirty or blocked air intake, etc. Under normal operation, the magnetron temperature fuse remains closed. However, when abnormally high temperatures are reached within the magnetron, the magnetron temperature fuse will open at 302oF(150oC) causing the oven to shut down. NOTE: This is fuse. It does not reset.

R-430DK R-430DW R-430DQ R-440DK R-440DW

TROUBLESHOOTING GUIDE

Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.

When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which will be found in the "Test Procedure "section.

IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, relay (RY1)

primary interlock relay (RY2), door sensing switch and secondary interlock switch before replacing the monitor fuse. If the monitor fuse is replaced, the monitor switch must also be replaced. Use part FFS-BA016/ KIT as an assembly.

IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases, be

necessary to connect the power supply cord after the outer case has been removed, in this event,

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the leads to the primary of the power transformer.

5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.

6. After that procedure, reconnect the power supply cord.

When the testing is completed

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Reconnect the leads to the primary of the power transformer.

5. Reinstall the outer case (cabinet).

6. Reconnect the power supply cord after the outer case is installed.

7. Run the oven and check all functions.

R-430DK R-430DW R-430DQ R-440DK R-440DW

CK = Check / RE = Replace

CONDITION

OFF CONDITION

COOKING CONDITION

SENSOR COOKING CONDITION

TEST PROCEDURE

POSSIBLE CAUSE

AND

DEFECTIVE PARTS

PROBLEM

Home fuse or circuit breaker blows when power cord is plugged into wall receptacle

Monitor fuse blows when power cord is plugged into wall receptacle.

All letters and indicators do not appear in display when power cord is first plugged into wall outlet.

Display does not operate properly when STOP/CLEAR key is touched. (Buzzer should sound and ":" or time of day should appear in display.)

Oven lamp does not light when door is opened.

Oven lamp does not go out when door is closed.

Oven lamp lights but fan motor and turntable motor do not operate.

Oven does not go into cook cycle when START pad is touched

Oven seems to be operating but little or no heat is produced in oven load. (Food incompletely cooked or not cooked at all at end of cook cycle.)

Oven goes into a cook cycle but extremely uneven heating is produced in oven load (food).

Oven does not cook properly when programmed for Cooking Power 5 mode. (Operates properly on Cooking Power 10 (HIGH) mode.)

Oven goes into COMPU DEFROST but food is not defrosted well.

AH sensor does not end during sensor cooking condition. (Oven does not shut off after a cup of water is boiling by sensor cooking)

Oven stops at 16 sec. after starting.

RE RE

ABCDEEF FGH

SHORT IN POWER CORD

SHORT OR OPENED WIRING

MAGNETRON

POWER TRANSFORMER

H.V. RECTIFIER ASSEMBLY

RE RE

HIGH VOLTAGE CAPACITOR

CAVITY TEMPERATURE FUSE

MAGNETRON TEMPERATURE FUSE

PRIMARY INTERLOCK SYSTEM

SECONDARY INTERLOCK SWITCH

MONITOR SWITCH

MONITOR FUSE

CKICKCKCK

OVEN LAMP OR SOCKET

COOLING FAN MOTOR

TURNTABLE MOTOR

TOUCH CONTROL PANEL

WRONG OPERATION

LOW VOLTAGE

J K L M N

DIRTY OVEN CAVITY

KEY UNIT

RELAY (RY1)

COMPU DEFROST

FOIL PATTERN ON PWB.

AH SENSOR

PROCEDURE

LETTER

A MAGNETRON ASSEMBLY TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

TEST PROCEDURES

COMPONENT TEST

R-430DK R-430DW R-430DQ R-440DK R-440DW

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

4. To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check across the magnetron filament leads should indicate less than 1 ohm.

5. To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance the magnetron is grounded and must be replaced.

6. Reconnect all leads removed from components during testing.

7. Reinstall the outer case (cabinet).

8. Reconnect the power supply cord after the outer case is installed.

9. Run the oven and check all functions.

MICROWAVE OUTPUT POWER

The following test procedure should be carried out with the microwave oven in a fully assembled condition (outer case fitted).

HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD BE OBSERVED.

Power output of the magnetron can be measured by performing a water temperature rise test. This test should only be used if above tests do not indicate a faulty magnetron and there is no defect in the following components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will require a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type temperature tester. For accurate results, the following procedure must be followed carefully:

1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water with a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple through the water until the temperature stabilizes. Record the temperature of the water.

2. Place the cup of water in the oven. Operate oven at POWER 10(HIGH) selecting more than 60 seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second hand of a watch or the digital read-out countdown.

3. Remove the cup from the oven and again measure the temperature, making sure to stir the thermometer or thermocouple through the water until the maximum temperature is recorded.

4. Subtract the cold water temperature from the hot water temperature. The normal result should be 38 to 78oF(21 to 42.6oC) rise in temperature. If the water temperatures are accurately measured and tested for the required time period the test results will indicate if the magnetron tube has low power output (low rise in water temperature) which would extend cooking time or high power output (high rise in water temperature) which would reduce cooking time. Because cooking time can be adjusted to compensate for power output, the magnetron tube assembly should be replaced only if the water temperature rise test indicates a power output well beyond the normal limits. The test is only accurate if the power supply line voltage is 120 volts and the oven cavity is clean.

B POWER TRANSFORMER TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the primary input terminals and measure the resistance of the transformer with an ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be approximately 90 ohms; the resistance of the filament coil should be less than 1 ohm.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO MEASURE THE FILAMENT AND HIGH VOLTAGE.)

TEST PROCEDURES

R-430DK R-430DW R-430DQ R-440DK R-440DW

PROCEDURE

LETTER

C HIGH VOLTAGE RECTIFIER TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance across the terminals and observe, reverse the leads to the rectifier terminals and observe meter reading. If a short is indicated in both directions, or if an infinite resistance is read in both directions, the rectifier is probably defective and should be replaced.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.

D HIGH VOLTAGE CAPACITOR TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads and check for short or open between the terminals using an ohmmeter. Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate continuity for a short time and should indicate an open circuit once the capacitor is charged. If the above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either of the terminals and case. If it is shorted, replace the capacitor.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

COMPONENT TEST

E CAVITY TEMPERATURE FUSE TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. A continuity check across the cavity temperature fuse terminals should indicate a closed circuit unless the temperature of the cavity temperature fuse reaches approximately 302oF(150oC). An open cavity temperature fuse indicates overheating of the oven, exchange the cavity temperature fuse and check inside of oven cavity and for improper setting of cooking time or operation of control unit. Check for restricted air flow through the vent holes of the oven cavity, especially the cooling fan and air guide.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

MAGNETRON TEMPERATURE FUSE TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. A continuity check across the magnetron temperature fuse terminals should indicate a closed circuit unless the temperature of the magnetron temperature fuse reaches approximately 302oF(150oC). An open magnetron temperature fuse indicates overheating of the magnetron. Check for restricted air flow to the magnetron, especially the cooling fan air guide.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

R-430DK R-430DW R-430DQ R-440DK R-440DW

TEST PROCEDURES

PROCEDURE

LETTER

CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM TEMPERA-

TURE, REPLACE TEMPERATURE FUSE.

F SECONDARY INTERLOCK SWITCH TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal of the switch. The meter should indicate an open circuit with the door open and a closed circuit with the door closed. If improper operation is indicated, replace the secondary interlock switch.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

PRIMARY INTERLOCK SYSTEM TEST

DOOR SENSING SWITCH

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling fan,

turntable and oven light will be activated by RY1.

COMPONENT TEST

PRIMARY INTERLOCK RELAY (RY2)

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect two (2) wire leads from the male tab terminals of the Primary Interlock Relay. Check the state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay contacts are closed, replace the circuit board entirely or the relay itself.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

G MONITOR SWITCH TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Before performing this test, make sure that the secondary interlock switch and the primary interlock relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire lead from the monitor switch (COM) terminal. Check the monitor switch operation by using the ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the monitor switch actuator is pushed by a screw driver through the lower latch hole on the front plate of the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed in), the meter should indicate an open circuit. If improper operation is indicated, the switch may be defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (COM) terminal and check the continuity of the monitor circuit.

TEST PROCEDURES

R-430DK R-430DW R-430DQ R-440DK R-440DW

PROCEDURE

LETTER

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

H BLOWN MONITOR FUSE TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. If the monitor fuse is blown when the door is opened, check the primary interlock relay, secondary interlock switch and monitor switch according to the "TEST PROCEDURE" for those switches before replacing the blown monitor fuse.

CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE, TEST THE PRIMARY INTERLOCK

RELAY, SECONDARY INTERLOCK SWITCH, DOOR SENSING SWITCH AND MONITOR

SWITCH FOR PROPER OPERATION. If the monitor fuse is blown by improper switch operation, the monitor fuse and monitor switch must be replaced with "monitor fuse and monitor switch assembly" part number FFS-BA016/KIT, even if the monitor switch operates normally. The monitor fuse and monitor switch assembly is comprised of a 20 ampere fuse and switch.

5. Reconnect all leads removed from components during testing.

6. Reinstall the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

COMPONENT TEST

Screw Driver

Secondary Interlock Switch

RED

WHT/WHT

Monitor Switch

Ohmmeter

I TOUCH CONTROL PANEL ASSEMBLY TEST

The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore, unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter and ohmmeter. In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key Unit, and also the Control Unit is divided into two units, LSI Unit and Power Unit, and troubleshooting by unit replacement is described according to the symptoms indicated.

Before testing,

1) Disconnect the power supply cord, and then remove outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Disconnect the leads to the primary of the power transformer.

5) Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.

6) After that procedure, re-connect the power supply cord.

1. Key Unit.

NOTE ;

1) Disconnect the power supply cord, and then remove outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Check Key unit ribbon connection before replacement.

5) Reconnect all leads removed from components during testing.

6) Re-install the outer case (cabinet).

7) Reconnect the power supply cord after the outer case is installed.

8) Run the oven and check all functions.

R-430DK R-430DW R-430DQ R-440DK R-440DW

TEST PROCEDURES

PROCEDURE LETTER COMPONENT TEST

The following symptoms indicate a defective key unit. a) When touching the pads, a certain pad produces no signal at all. b) When touching a number pad, two figures or more are displayed. c) When touching the pads, sometimes a pad produces no signal. If the Key unit is defective.

1) Disconnect the power supply cord, and then remove outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Replace the Key unit.

5) Reconnect all leads removed from components during testing.

6) Re-install the outer case (cabinet).

7) Reconnect the power supply cord after the outer case is installed.

8) Run the oven and check all functions.

2. Control Unit The following symptoms indicate a defective control unit. Before replacing the control unit, perform the Key unit test (Procedure J) to determine if control unit is faulty.

2-1 In connection with pads.

a) When touching the pads, a certain group of pads do not produce a signal. b) When touching the pads, no pads produce a signal.

2-2 In connection with indicators

a) At a certain digit, all or some segments do not light up. b) At a certain digit, brightness is low. c) Only one indicator does not light. d) The corresponding segments of all digits do not light up; or they continue to light up. e) Wrong figure appears. f) A certain group of indicators do not light up. g) The figure of all digits flicker. h) The following symptoms indicate a defective LSI unit.

• When touching the keys on the touch screen, a certain key produces no signal at all.

• When touching a number key on the touch screen, two figures or more are displayed.

• When touching the keys on the touch screen, sometimes a key produces no signal.

2-3 Other possible problems caused by defective control unit.

a) Buzzer does not sound or continues to sound. b) Clock does not operate properly. c) Cooking is not possible.

When testing is completed,

1) Disconnect the power supply cord, and then remove outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Reconnect all leads removed from components during testing.

5) Re-install the outer case (cabinet).

6) Reconnect the power supply cord after the outer case is installed.

7) Run the oven and check all functions..

J KEY UNIT TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the contacts are closed when the door is closed and open when the door is open. If the door sensing switch (stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and make sure the door sensing switch is closed (either close the door or short the door sensing switch connecter). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.

5. Reconnect all leads removed from components during testing.

PROCEDURE

LETTER

6. Re-install the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed.

8. Run the oven and check all functions.

G 8

G 7 G 6 G 5 G 4 G 3 G 2 G 1

G 9

G10

G11

G12

G13

G14

09876

Frozen

Minute

Plus

One Dish

Dinners

Popcorn

Snacks

Stop

Clear

Sensor Reheat

Clock

Lunch on

the Run

Baked

Potatoes

Kitchen

Timer

Power

Level

Custom

Help

R-430DK/DW/DQ R-440DK/DW

K RELAY TEST

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the leads to the primary of the power transformer.

5. Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.

6. After that procedure, re-connect the power supply cord.

7. Remove the outer case and check voltage between Pin No. 1 of the 2 pin connector (A) and the common terminal of the relay RY1 on the control unit with an A.C. voltmeter. The meter should indicate 120 volts, if not check oven circuit.

RY1 and RY2 Relay Test

These relays are operated by D.C. voltage Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.

DC. voltage indicated ............. Defective relay.

DC. voltage not indicated ........ Check diode which is connected to the relay coil. If diode is good,

RELAY SYMBOL OPERATIONAL VOLTAGE CONNECTED COMPONENTS

RY1 Approx. 24.0V D.C.(R-430D) & 24.8V D.C.(R-440D) Oven lamp / Turntable motor / Cooling fan motor RY2 Approx. 23.0V D.C.(R-430D) & 23.9V D.C.(R-440D) Power transformer

8. Disconnect the power supply cord, and then remove outer case.

9. Open the door and block it open.

10. Discharge high voltage capacitor.

11. Reconnect all leads removed from components during testing.

12. Re-install the outer case (cabinet).

13. Reconnect the power supply cord after the outer case is installed.

14. Run the oven and check all functions.

L COMPU DEFROST TEST

Start

Touch On

Breakfast

Bar

Super

Defrost

Beverage

Center

COMPU

DEFROST

Fish/

Seafood

TEST PROCEDURES

COMPONENT TEST

Fresh

Rice

Vegetables

Ground

Poultry

Frozen

Vegetables

Meat

Frozen entrees

control unit is defective.

G 5

G 6

G13

G12

G11

G15

G 1

Set Up

Pasta

Grains

Baked

Potatoes

Poultry

G 2 G 3 G14

More from

Defrost

Beverage

Vegetables

Reheat

Seafood

3+6

Center

Fish /

Your

Microwave

STOP

CLEAR

Frozen

Food

Popcorn

Meat

START

MINUTE

PLUS

R-430DK R-430DW R-430DQ R-440DK R-440DW

WARNING : The oven should be fully assembled before following procedure.

(1)Place one cup of water in the center of the turntable tray in the oven cavity. (2)For R-430DK/DW/DQ, Close the door, touch the " Compu Defrost " pad three times and touch the

number pad 5. And then touch the start pad. For R-440DK/DW, Close the door, touch the Defrost pad and select compu Defrost. Then select Steaks/

Chops/Fish. (Now, weight 0.5lb is set.) And then touch the start pad.

(3)The oven is in Compu Defrost cooking condition. (4)The oven will operate as follows 1ST STAGE 2ND STAGE

WEIGHT

LEVEL TIME LEVEL TIME

0.5lb 60% 25sec. 40% 20sec.

(5) If improper operation is indicated, the control unit is probably defective and should be checked.

R-430DK R-430DW R-430DQ R-440DK R-440DW

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

M FOIL PATTERN ON THE PRINTED WIRING BOARD TEST

To protect the electronic circuits, this model is provided with a fine foil pattern added

to the primary on the PWB, this foil pattern acts as a fuse.

1. Foil pattern check and repairs.

1) Disconnect the power supply cord, and then remove outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Follow the troubleshooting guide given below for repair.

STEPS OCCURRENCE CAUSE OR CORRECTION

1 Only pattern at "a" is broken. *Insert jumper wire J1 and solder. 2 Pattern at "a" and "b" are broken. *Insert the coil RCILF2003YAZZ between "c" and "d".

5) Make a visual inspection of the varistor. Check for burned damage and examine the transformer with a tester for the presence of layer short-circuit (for R-

R-430DK/DW/DQ

430D K/DW/DQcheck the primary coil resistance which is approximately 210 ohm ± 15%). (for R-440DK/DW/DQ check the primary coil resistance which is approximately 133 ohm ± 10%). If any abnormal condition is detected, replace the defective parts.

R-440DK/DW

VRS1

RY1

CN - A

(J1)

VRS1

OMIF

6) Reconnect all leads removed from components during testing.

7) Re-install the outer case (cabinet).

8) Reconnect the power supply cord after the outer case is installed.

9) Run the oven and check all functions.

2. Follow the troubleshooting guide given below, if indicator does not light up after above check and repairs are finished.

1) Disconnect the power supply cord, and then remove outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Disconnect the leads to the primary of the power transformer.

5) Ensure that these leads remain isolated from other components and oven chassis by using

insulation tape.

6) After that procedure, re-connect the power supply cord.

7) Follow the troubleshooting guide given below for repair.

STEPS OCCURRENCE CAUSE OR CORRECTION

The rated AC voltage is not present between

1 Pin No. 1 of the 2-pin connector (A) and the Check supply voltage and oven power cord.

common terminal of the relay RY1. The rated AC voltage is present at primary Low voltage transformer or secondary circuit defective.

side of low voltage transformer. Check and repair.

8) Disconnect the power supply cord, and then remove outer case.

9) Open the door and block it open.

10) Discharge high voltage capacitor.

11) Reconnect all leads removed from components during testing.

12) Re-install the outer case (cabinet).

13) Reconnect the power supply cord after the outer case is installed.

14) Run the oven and check all functions.

TEST PROCEDURES

R-430DK R-430DW R-430DQ R-440DK R-440DW

PROCEDURE

LETTER

N AH SENSOR TEST

Checking the initial sensor cooking condition Warning: The oven should be fully assembled before following procedure.

1) The oven should be plugged in at least two minutes before sensor cooking.

2) Room temperature should not exceed 9 5oF(35oC).

3) The unit should not be installed in any area where heat and steam are generated. The unit should not be installed for example, next to conventional surface unit. Refer to the "INSTALLATION INSTRUCTIONS" of the operational manual.

(4)Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To permit

adequate ventilation, be sure to install so as not to block these vents. There should be some space for air circulation.

(5)Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture

with dry cloth or paper towel.

(6)The Sensor works with food at normal storage temperature. For example, chicken pieces would be

at refrigerator temperature and canned soup at room temperature.

(7)Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The

sensor will detect the vapor given of by the spray and turn off before food is properly cooked.

(8)If the sensor has not detected the vapor of the food, ERROR will apear and the oven will shut off.

Water load cooking test Warning: The oven should be fully assembled before following procedure.

Make sure the oven the oven has been plugged in at least two minutes before checking sensor cook operation . the cabinet should be installed and screws tightened. (1) The oven should be plugged in at least two minutes before sensor cooking (2) Fill approximately 200 milliliters (7.2 oz) of tap water in 1000 milliliters measuring cup. (3) Place the container on the center of tray in the oven cavity. (4) Close the door. (5) For R-430DK/DW/DQ, Touch SENSOR REHEAT pad once and touch the start pad. Now, the oven is in the sensor cooking condition "SENSOR REHEAT" will appear in the display. For R-440DK/DW, Touch Reheat pad. Now, the oven is in the sensor cooking condition and "REHEAT" will appear in the display for approx. 7 sec. and then "SENSING" will appear. (6) The oven will operate for the first 16 seconds, without generating microwave energy. NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during the first stage

of sensor cooking. (7) After approximately 16 seconds, microwave energy is produced, and the display should start to count down the remaining cooking time and the oven should turn off after water is boiling (bubbling). If the oven does not turn off, replace the AH sensor or check the control unit, refer to explaination below.

TESTING METHOD FOR AH SENSOR AND /OR CONTROL UNIT

To determine if the sensor is defective, the simplest method is to replace it with a new replacement sensor. (1) Disconnect the power supply cord, and then remove outer case. (2) Open the door and block it open. (3) Discharge high voltage capacitor. (4)Remove the AH sensor. (5)Install the new AH sensor. (6)Reconnect all leads removed from components during testing. (7)Re-install the outer case (cabinet) (8) Reconnect the power supply cord after the outer case is installed. (9)Reconnect the oven to the power supply and check the sensor cook operation as follows:

9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup. 9-2. Place the container on the center of tray in the oven cavity. 9-3. close the door. 9-4. For R-430DK/DW/DQ, Touch SENSOR REHEAT pad and touch the Start pad. For R-440DK/DW, touch REHEAT pad 9-5.The control panel is in automatic sensor operation. 9-6.The display will start to count down the remaining cooking time, and the oven will turn off automatically after the water is boiling (bubbling).

If new sensor does not operate properly, the problem is with the control unit, and refer to explanation below.

COMPONENT TEST

R-430DK R-430DW R-430DQ R-440DK R-440DW

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

CHECKING CONTROL UNIT

(1) Disconnect the power supply cord, and then remove outer case. (2) Open the door and block it open. (3) Discharge high voltage capacitor. (4) Disconnect the sensor connector that is mounted to control panel. (5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel. (6) Disconnect the leads to the primary of power transformer. (7) Ensure that these leads remain isolated from other components and oven chassis by using insulation tape. (8) After that procedure, re-connect the power supply cord. (9) Check the sensor cook operation proceed as follows: 9-1 For R-430DK/DW/DQ, Touch SENSOR REHEAT pad and touch start pad. For R-440DK/DW, Touch Reheat pad. 9-2 The control panel is in the sensor cooking operation. 9-3 For R-430DK/DW/DQ, after approximately 30 seconds, push plunger of select switch for more than 3 seconds. For R-440DK/DW, after approximately 50 seconds, push plunger of select switch for more than 3 seconds. This condition is same as judgement by AH sensor. 9-4 After approximately 3 seconds, the display shows "xx.xx" which is remaining cooking time, and the display count down. If the above is not the case, the control unit is probably defective. If the above is proper, the AH sensor is probably defective. (10)Disconnect the power supply cord, and then remove outer case. (11)Open the door and block it open. (12)Discharge high voltage capacitor. (13)Reconnect the sensor connector that is mounted to control panel. (14)Carry out the necessary repair. (15)Reconnect all leads removed from components during testing and repairing. (16)Re-install the outer case (cabinet) (17)Reconnect the power supply cord after the outer case is installed. Run the oven and check all

functions

(18)Carry out the "water load cooking test" again and ensure that the oven work properly.

TOUCH CONTROL PANEL ASSEMBLY

OUTLINE OF TOUCH CONTROL PANEL FOR R-430DK/DW/DQ

R-430DK R-430DW R-430DQ R-440DK R-440DW

The touch control section consists of the following units. (1)Key Unit

(2)Control Unit (The Control Unit consists of Power Unit and

LSI Unit).

The principal functions of these units and the signals communicated among them are explained below.

Key Unit

The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit through P110-P117. When a key pad is touched, a signal is completed through the key unit and passed back to the LSI through P100, P101, P102, P103, ANI6 and ANI7 to perform the function that was requested.

Control Unit

Control unit consists of LSI, ACL circuit, indicator circuit, power source circuit, relay circuit, buzzer circuit, synchronizing signal circuit and back light circuit.

1) ACL

This circuit generates a signal which resets the LSI to the initial state when power is supplied.

2) Indicator Circuit

This circuit consists of 40 segments and 16 common electrodes using a Liquid Crystal Display. The Liquid Crystal Display (LCD) is derived by LCD Driver IC3.

3) Power Source Circuit

This circuit generates voltages necessary in the control unit from the AC line voltage. In addition, the synchronizing signal is available in order to compose a basic standard time in the clock circuit.

Symbol Voltage Application

VC -5V LSI(IC1)

4) Relay Circuit

A circuit to drive the magnetron, fan motor, turntable motor and light the oven lamp.

5) Buzzer Circuit

The buzzer is responsive to signals from the LSI to emit audible sounds (key touch sound and completion sound).

6) Synchronizing Signal Circuit

The power source synchronizing signal is available in order to compose a basic standard time in the clock circuit. It accompanies a very small error because it works on commercial frequency.

7) Door Sensing Switch

A switch to “tell” the LSI if the door is open or closed.

8) Back Light Circuit

A circuit to drive the back light (Light emitting diodes LD10- LD19).

9) Absolute Humidity Sensor Circuit

This circuit detects moisture of the cooking food to allow its automatic cooking.

LSI(IXA037DR): R-430DK/DW/DQ

The I/O signal of the LSI(IXA037DR) is detailed in the following table.

Pin No. Signal I/O Description

1-2 P26-P27 OUT Terminal not used. 3-5 P70-P72 OUT Terminal not used.

6 IC IN Connected to VC. 7 X2 OUT Internal clock oscillation output.

Output to control oscillation input to X2.

8X1INInternal clock oscillation frequency control input setting.

The internal clock frequency is set by inserting the ceramic filter oscillation circuit with respect to X1.

9 VDD1 IN Power source voltage: GND(0V).

The power source voltage to drive LSI is input to VDD1 terminal. 10 XT1 IN Connected to GND. 11 XT2 OUT Terminal not used.

R-430DK R-430DW R-430DQ R-440DK R-440DW

Pin No. Signal I/O Description

12 RESET IN Auto clear terminal.

Signal is input to reset the LSI to the initial state when power is applied. Temporarily set "L" level the moment power is applied, at this time the LSI is reset. Thereafter set

at "H" level. 13 INTP0 IN Connected to VC. 14 INTP1 IN Signal synchronized with commercial power source frequency.

This is the basic timing for time processing of LSI.

H : GND

15 P02 OUT Terminal not used. 16 P03 OUT Magnetron high-voltage circuit driving signal.

To turn on and off the cook relay (RY2).

The signals holds "L" level during

microwave cooking and "H" level while not

cooking. In other cooking modes (variable

cooking) the signal turns to "H" level and

"L" level in repetition according to the power

OFF

100 %

OFF

70 %

level.

(ON and OFF times for other power level.)

17 P04 OUT Oven lamp, fan motor and turntable motor driving signal

To turn on and off shut off relay (RY1). The

16.7 msec.

square waveform voltage is delivered to

the RY1 driving circuit and RY2 control

circuit.

During cooking

18 P05 OUT Terminal not used. 19 P110 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI7, P100, P101,

P102 and P103 terminal while one of G8 line keys on key matrix is touched. 20 P111 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI7, P100, P101,

P102 and P103 terminal while one of G7 line keys on key matrix is touched. 21 P112 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI7, P100, P101,

P102 and P103 terminal while one of G6 line keys on key matrix is touched. 22 P113 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI7, P100, P101,

P102 and P103 terminal while one of G5 line keys on key matrix is touched.

16.7 msec.

24 sec.

OFF

8 sec.

L : -5V

H : GND

L : -5V

H : GND

L : -5V

H : GND

L : -5V

23 P114 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI6, ANI7, P100, P101, P102 and P103 terminal while one of G4 line keys on key matrix is touched.

24 P115 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI7, P100, P101, P102 and P103 terminal while one of G3 line keys on key matrix is touched.

25 P116 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI7, P100, P101, P102 and P103 terminal while one of G2 line keys on key matrix is touched.

26 P117 OUT Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to ANI7, P100, P101, P102 and P103 terminal while one of G1 line keys on key matrix is touched.

Pin No. Signal I/O Description

27 AVSS IN Connected to VC.

28-31 ANI0-ANI3 IN Terminal to change cooking input according to the Model.

By using the A/D converter contained in the LSI, DC voltage in accordance with the Model in operation is applied to set up its cooking constant.

32 ANI4 IN Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is

an analog input terminal from the AH sensor circuit, and connected to the A/D converter built into the LSI.

33 ANI5 IN AH sensor input.

This input is an analog input terminal from the AH sensor circuit, and connected to the A/D converter built into the LSI.

34 ANI6 IN Input terminal to judge the model.

The signal out of P114 will be input into ANI6 through G4 line on key matrix. The LSI will judge the model by this signal.

35 ANI7 IN Signal coming from touch key.

When either G13 line on key matrix is touched, a corresponding signal out of P110 P117 will be input into ANI7. When no key is touched, the signal is held at "H" level.

36 VDD0 IN Power source voltage : GND(0V).

The power source voltage to drive LSI is input to VDD0 terminal.

37 AVREF IN A/D converter power source voltage : GND(0V).

The power source voltage to drive the A/D converter. Connected to GND.

38 P100 IN Signal similar to ANI7.

When either G12 line on key matrix is touched, a corresponding signal will be input into P100.

39 P101 IN Signal similar to ANI7.

When either G11 line on key matrix is touched, a corresponding signal will be input into P101.

40 VSS1 IN Power source voltage : -5.0V.

The power source voltage to the drive LSI is input to VSS1 terminal. Connected to VC.

41 P102 IN Signal similar to ANI7.

When either G10 line on key matrix is touched, a corresponding signal will be input into P102.

42 P103 IN Signal similar to ANI7.

When either G9 line on key matrix is touched, a corresponding signal will be input into P103.

43 P30 OUT Terminal not used.

44-48 P31-P35 OUT Used for initial balancing of the bridge circuit (absolute humidity sensor).

49 P36 OUT Signal to sound buzzer (2.0 kHz).

A: key touch sound. B: Completion sound.

0.1 sec.

2.0 sec.

H : GND

L : -5V H : GND

L : -5V

50 P37 IN To input signal which communicates the door open/close information to LSI.

Door close "H" level signal (0V). Door open "L" level signal (-5V).

R-430DK R-430DW R-430DQ R-440DK R-440DW

Pin No. Signal I/O Description

51-54 COM0-COM3 OUT Terminal not used.

55 BIAS IN Terminal not used. 56 VLC0 IN Terminal not used.

57-58 VLC1-VLC2 IN Terminal not used.

59 VSS0 IN Power source voltage: -5.0V.

The power source voltage to the LSI is input to VSS0 terminal. Connected to VC. 60-83 S0-S23 OUT Terminal not used. 84-97 P97-P82 OUT Data output terminal to LCD driver IC3. 98-99 P81-P80 OUT Terminal not used.

100 P2 5 OUT Terminal not used.

ABSOLUTE HUMIDITY SENSOR CIRCUIT R-430DK/DW/DQ

SW1 SW2

SW3 SW4 SW5

P31 P32 P33 P34 P35

LSI (IC1)

ANI4

ANI5

620k 300k 150k

75k

37.4k

47 48

47k

10k

1234

5678

0.01uF

0.015uF

0.01uF

VA : -15V

R90

F-2

1.8k

IC2

F-1

F-3

3.57k

3.32k

VC : -5V

0.1

C. Thermistor in closed vessel S. Thermistor in open vessel

R98 R99

R96

R91

360k

R93

R92

R94

R95

D90

R100 R101

R102

R97

R-430DK R-430DW R-430DQ R-440DK R-440DW

(1) Structure of Absolute Humidity Sensor

The absolute humidity sensor includes two thermistors as shown in the illustration. One thermistor is housed in the closed vessel filled with dry air while another in the open vessel. Each sensor is provided with the protective cover made of metal mesh to be protected from the external airflow.

(2) Operational Principle of Absolute Humidity Sensor

The figure below shows the basic structure of an absolute humidity sensor. A bridge circuit is formed by two thermistors and two resistors(R1 and R2). The output of the bridge circuit is to be amplified by the operational amplifier. Each thermistor is supplied with a current to keep it heated at about 150oC (302oF), the resultant heat is dissipated in the air and if the two thermistors are placed in different degrees of heat conductivity leading to a potential difference between them causing an output voltage from the bridge circuit, the intensity of which is increased as the absolute humidity of the air inceases. Since the output is very minute, it is amplified by the operational amplifier.

With this voltage given, the switches SW1 to SW5 in the LSI are turned on in such a way as to change the resistance values in parallel with R107 ~ R111 of IC2 . Changing the resistance value results in that there is the same potential at both F-3 terminal of the absolute humidity sensor and AN0 terminal of the LSI. The voltage of AN1 terminal will indicat about 16 seconds about -2.50 V. This initial balancing is set up about 16 seconds after the unit is put in the Sensor Cooking mode. As the sensor cooking proceeds, the food is heated to generate moisture by which the resistance balance of the bridge circuit is deviated to increase the voltage available at AN1 terminal of the LSI. Then the LSI observes that the voltage at AN1 terminal and compares it with its initial value, and when the comparison rate reaches the preset value (fixed for each menu to be cooked), the LSI causes the unit to stop sensor cooking; thereafter, the unit goes in the next operation automatically. When the LSI starts to detect the initial voltage at AN1 terminal 16 seconds after the unit has been put in the Sensor Cooking mode, if it is not possible to balance of the bridge circuit due to disconnection of the absolute humidity sensor, ERROR will appear on the display and the cooking is stopped.

1) Absolute humidity sensor circuit

Absolute humidity output voltage characteristics

(3) Detector circuit of Absolute Humidity Sensor circuit

This detector circuit is used to detect the output voltage of the absolute humidity circuit to allow the LSI to control sensor cooking of the unit. When the unit is set in the sensor cooking mode, 16 seconds clearing cycle occurs then the detector circuit starts to function and the LSI observes the initial voltage available at its AN1 terminal.

R-430DK R-430DW R-430DQ R-440DK R-440DW

TOUCH CONTROL PANEL ASSEMBLY

OUTLINE OF TOUCH CONTROL PANEL FOR R-440DK/DW

The touch control section consists of the following units.

This circuit generates a signal which resets the LSI (IC1) to the initial state when power is supplied.

(1) Key Unit (2) Control Unit (The Control Unit consists of Power Unit

and LSI Unit).

The principal functions of these units and the signals communicated among them are explained below.

Key Unit

The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit through P93, P94, P95 and P40. When a key pad is touched, a signal is completed through the key unit and passed back to the LSI through PB1, PB2, PB3, PB4, PB5 and AN1 to perform the function that was requested.

Control Unit

Control unit consists of LSI, IC, ACL circuit, indicator circuit, power source circuit, relay circuit, buzzer circuit, synchronizing signal circuit, key unit circuit, touch screen circuit, absolute humidity sensor circuit and back light circuit.

1) IC1 (LSI)

This is a microcomputer, responsible for controlling the entire control unit.

2) IC2

This is a read only memory IC, responsible for giving IC1 the all programmes.

7) Indicator Circuit

This circuit consists of 100 x 160 dots using a Liquid Crystal Display. The Liquid Crystal Display (LCD) is drived by IC5.

8) Power Source Circuit

Symbol Voltage Application

VC +5V LSI(IC1)

9) Relay Circuit

A circuit to drive the magnetron, fan motor, turntable motor and light the oven lamp.

10) Buzzer Circuit

The buzzer is responsive to signals from the LSI to emit audible sounds (key touch sound and completion sound).

11) Synchronizing Signal Circuit

The power source synchronizing signal is available in order to compose a basic standard time in the clock circuit. It accompanies a very small error because it works on commercial frequency.

3) IC3

This is an amplifier IC. This IC controls the contrast of LCD and amplify the sensor signal.

4) IC4

This is a memory IC. This memorizes the contrast of LCD.

5) IC5

This IC drives the LCD.

6) ACL

12) Door Sensing Switch

A switch to “tell” the LSI if the door is open or closed.

13) Back Light Circuit

A circuit to drive the back light (Light emitting diodes LED1 and LED2).

14) Absolute Humidity Sensor Circuit

This circuit detects moisture of the cooking food to allow its automatic cooking.

15) Touch Screen

The touch screen is composed of a matrix, signal generated in the LSI are sent to the key unit through P41, P42, P43 and P44. When a key is touched, a signal is completed through the touch screen and passed back to the LSI through PB1, PB2, PB3, PB4 and PB5 to perform the function that was requested.

LSI(IXA029DR) : R-440DK/DW

The I/O signal of the LSI(IXA029DR) is detailed in the following table.

Pin No. Signal I/O Description

1 TIOCA2 OUT Terminal not used. 2 A20 OUT Terminal not used. 3 Vcc IN Power source voltage : +5.0V.

The power source voltage to drive LSI is input to Vcc terminal. Connected to Vcc.

4 TMO0 OUT Signal to sound buzzer.

A: key touch sound (short beep). B: Completion sound (melody or long beep).

5 PB1 IN Signal coming from touch key.

When either G11 line on key matrix is touched, a corresponding signal out of P93, P94, P95, P40, P41, P42, P43 and P44 will be input into PB1. When no key is touched, the signal is held at "H" level.

6 PB2 IN Signal similar to PB1.

When either G12 line on key matrix is touched, a corresponding signal will be input into PB2.

7 PB3 IN Signal similar to PB1.

When either G13 line on key matrix is touched, a corresponding signal will be input into PB3.

8 PB4 IN Signal similar to PB1.

When either G6 line on key matrix is touched, a corresponding signal will be input into PB4.

9 PB5 IN Signal similar to PB1.

When either G5 line on key matrix is touched, a corresponding signal will be input into PB5.

10-11 PB6-PB7 OUT Terminal not used.

12 RESO OUT Terminal not used. 13 Vss IN Power source voltage: GND(0V).

The power source voltage to drive LSI is input to Vss terminal. 14 TxD0 OUT Data signal is output to a memory IC (IC4). 15 P91 OUT Clock signal is output to a memory IC (IC4). 16 RxD0 OUT Terminal not used. 17 P93 OUT Key strobe signal.

Signal applied to key unit section. A pulse signal is input to PB1-PB5 terminal while

one of G1 line keys on key matrix is touched. 18 P94 OUT Key strobe signal.

Signal applied to key unit section. A pulse signal is input to PB1-PB5 terminal while

one of G2 line keys on key matrix is touched. 19 P95 OUT Key strobe signal.

Signal applied to key unit section. A pulse signal is input to PB1-PB5 and AN1

terminal while one of G3 line keys on key matrix is touched. 20 P40 OUT Key strobe signal.

Signal applied to key unit section. A pulse signal is input to PB1-PB5 terminal while

one of G14 line keys on key matrix is touched. 21 P41 OUT Key strobe signal.

Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal

while one of G7 line keys on key matrix is touched. 22 P42 OUT Key strobe signal.

Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal

while one of G8 line keys on key matrix is touched. 23 P43 OUT Key strobe signal.

Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal

while one of G9 line keys on key matrix is touched. 24 Vss IN Power source voltage : GND(0V).

The power source voltage to drive LSI is input to VSS terminal.

R-430DK R-430DW R-430DQ R-440DK R-440DW

Pin No. Signal I/O Description

25 P44 OUT Key strobe signal.

Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal while one of G10 line keys on key matrix is touched.

26 P45 OUT Oven lamp, fan motor and turntable motor driving signal

To turn on and off shut off relay (RY1). The square waveform voltage is delivered to the RY1 driving circuit and RY2 control circuit.

27 P46 OUT Magnetron high-voltage circuit driving signal.

To turn on and off the cook relay (RY2). The signals holds "H" level during microwave cooking and "L" level while not

100 PERCENT

cooking. In other cooking modes (variable cooking) the signal turns to "L" level and "H" level in repetition according to the power level.

70 PERCENT

(ON and OFF times for other power level.)

28 P47 OUT Terminal not used.

29-36 D8-D15 OUT Data signal is output to IC2 and IC5.

37 Vcc IN Power source voltage : +5V.

The power source voltage to drive LSI is input to Vcc terminal. Connected to VCC.

38-45 A0-A7 OUT Address signal is output to IC2 and IC5.

46 Vss IN Power source voltage : GND (0V).

The power source voltage to drive LSI is input to Vss terminal.

47-58 A8-A19 OUT Address signal is output to IC2 and IC5.

59 Vss IN Power source voltage : GND (0V).

The power source voltage to drive LSI is input to Vss terminal. 60 WATT IN Connected to VCC. 61 P61 OUT Envelope signal to sound buzzer.

A: key touch sound (short beep). B: Completion sound (melody or long beep). 62 P62 OUT Reset signal is output to IC5. 63 P67 OUT Terminal not used. 64 STBY IN Connected to VCC. 65 RES IN Auto clear terminal.

Signal is input to reset the LSI to the initial state when power is applied. Temporarily

set "L" level the moment power is applied, at this time the LSI is reset. Thereafter set

at "H" level. 66 NMI IN Connected to GND. 67 Vss IN Power source voltage : GND (0V).

The power source voltage to drive LSI is input to Vss terminal. 68 EXTAL OUT Internal clock oscillation output.

Output to control oscillation input to EXTAL. 69 XTAL IN Internal clock oscillation frequency control input setting.

The internal clock frequency is set by inserting the ceramic filter oscillation circuit

with respect to XTAL. 70 Vcc IN Power source voltage : +5V.

The power source voltage to drive LSI is input to Vcc terminal. Connected to VCC. 71 AS OUT Terminal not used. 72 RD OUT Read strobe signal is output to RD terminal of IC5.

16.7 msec.

During cooking

OFF

24 sec.

8 sec.

OFF

H : +5V

L : GND

H : +5V

L : GND H : +5V

L : GND

Pin No. Signal I/O Description

73 HWR OUT Write strobe signal is output to WR terminal of IC5. 74 LWR OUT Terminal not used.

75-76 MD0-MD1 IN Connected to VCC.

77 MD2 IN Connected to GND. 78 Avcc IN A/D converter power source voltage : +5V.

The power source voltage to drive the A/D converter. Connected to VCC.

79 Vref IN A/D converter power source voltage : +5V.

The power source voltage to drive the A/D converter. Connected to VCC.

80 AN0 IN Terminal to judge whether the model has the sensor cooking function or not.

By using the A/D converter contained in the LSI, DC voltage in accordance with the Model in operation is applied to judge whether the model has the sensor cooking function or not.

81 AN1 IN Input terminal to judge the model.

The signal out of P95 will be input into AN1 through G15 line on key matrix. The LSI will judge the model by this signal.

82 AN2 IN Terminal to change cooking input according to the model.

By using the A/D converter contained in the LSI, DC voltage in accordance with the

Model in operation is applied to set up its cooking constant. 83 AN3 IN Connected to VCC. 84 AN4 IN To input signal which communicates the door open/close information to LSI.

Door close "H" level signal (+5V). Door open "L" level signal (GND). 85 AN5 IN Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is

an analog input terminal from the AH sensor circuit, and connected to the A/D

converter built into the LSI. 86 AN6 IN AH sensor input.

This input is an analog input terminal from the AH sensor circuit, and connected to

the A/D converter built into the LSI. 87 DA1 OUT The signal for the power source to drive the LCD is output to IC3. 88 Avss IN A/D converter power source voltage : GND(0V).

The power source voltage to drive the A/D converter. Connected to GND. 89 IRQ0 IN Signal synchronized with commercial power source frequency.

This is the basic timing for time processing of LSI.

R-430DK R-430DW R-430DQ R-440DK R-440DW

H : +5V

16.7 msec.

90-91 P81-P82 OUT Terminal not used.

92 CS1 OUT Chip select signal is output to CS terminal of IC5. 93 CS0 OUT Chip select signal is output to CE terminal of IC2. 94 Vss IN Power source voltage : GND (0V).

The power source voltage to drive the LSI is input to Vss terminal.

95-99 PA0-PA4 OUT Used for initial balancing of the bridge circuit (absolute humidity sensor).

100 PA5 OUT Clock signal is output to IC5.

L : GND

R-430DK R-430DW R-430DQ R-440DK R-440DW

ABSOLUTE HUMIDITY SENSOR CIRCUIT (R-440DK/DW)

(1) Structure of Absolute Humidity Sensor

ventilation opening for sensing

Sensing part (Open vessel)

Thermistors

Sensing part (Closed vessel)

(2) Operational Principle of Absolute Humidity Sensor

The figure below shows the basic structure of an absolute humidity sensor. A bridge circuit is formed by two thermistors and two resistors (R1 and R2).

The output of the bridge circuit is to be amplified by the operational amplifier.

Each thermistor is supplied with a current to keep it heated at about 150½C (302½F), the resultant heat is dissipated in the air and if the two thermistors are placed in different humidity conditions they show different degrees of heat conductivity leading to a potential difference between them causing an output voltage from the bridge circuit, the intensity of which is increased as the absolute humidity of the air increases. Since the output is very minute, it is amplified by the operational amplifier.

Operational amplifier

Output voltage

Absolute humidity vs, output voltage characteristic

increase the voltage available at AN6 terminal of the LSI. Then the LSI observes that voltage at AN6 terminal and compares it with its initial value, and when the comparison rate reaches the preset value (fixed for each menu to be cooked), the LSI causes the unit to stop sensor cooking; thereafter, the unit goes in the next operation automatically. The LSI starts to detect the initial voltage at AN6 terminal 16 seconds after the unit has been put in the Sensor Cooking mode. If it is not possible to balance the bridge circuit due to disconnection of the absolute humidity sensor, ERROR will appear on the display and the cooking is stopped.

1) Absolute humidity sensor circuit

VA : +15V VC : +5V

D40

R40 330

C. Thermistor in closed vessel S. Thermistor in

open vessel

41 3.32K

42 3.57K

C40 0.1µF

R43 1.8K

R47 47K R48 620K

R49 300K

R50 150K

R51 75K

R52 37.4K

IC3

C41 0.015µF

R44 360K

R45 10K

R46 47K

C42 0.01µF

C43 0.01µF

AN6

AN5

PA0

PA1

PA2

PA3

PA4

LSI (IC1)

SW1

SW2

SW3

SW4

SW5

S : Thermistor open vessel

C : Thermistor closed vessel

utput voltage O

Absolute humidity (g/m )

(3) Detector Circuit of Absolute Humidity Sensor Circuit

This detector circuit is used to detect the output voltage of the absolute humidity circuit to allow the LSI to control sensor cooking of the unit. When the unit is set in the sensor cooking mode, 16 seconds clearing cycle occurs than the detector circuit starts to function and the LSI observes the initial voltage available at its AN6 terminal.

With this voltage given, the switches SW1 to SW5 in the LSI are turned on in such a way as to change the resistance values in parallel with R47 ~ R52. Changing the resistance values results in that there is the same potential at both F-3 terminal of the absolute humidity sensor and AN5 terminal of the LSI. The voltage of AN6 terminal will indicate about +2.5V. This initial balancing is set up about 16 seconds after the unit is put in the Sensor Cooking mode. As the sensor cooking proceeds, the food is heated to generate moisture by which the resistance balance of the bridge circuit is deviated to

TOUCH CONTROL PANEL SERVICING

1. Precautions for Handling Electronic Components

This unit uses CMOS LSI in the integral part of the circuits. When handling these parts, the following precautions should be strictly followed. CMOS LSI have extremely high impedance at its input and output terminals. For this reason, it is easily influenced by the surrounding high voltage power source, static electricity charge in clothes, etc. and sometimes it is not fully protected by the built-in protection circuit. In order to protect CMOS LSI.

1) When storing and transporting, thoroughly wrap them in aluminium foil. Also wrap all PW boards containing them in aluminium foil.

2) When soldering, ground the technician as shown in the figure and use grounded soldering iron and work table

approx. 1M ohm

2. Shapes of Electronic Components

R-440DK/DW

Transistor

R-430DK/DW/DQ

2. Servicing of Touch Control Panel

We describe the procedures to permit servicing of the touch control panel of the microwave oven and the precautions you must take when doing so. To perform the servicing, power to the touch control panel is available either from the power line of the oven itself or from an external power source.

(1)Servicing the touch control panel with power supply

of the oven:

CAUTION: THE HIGH VOLTAGE TRANSFORMER OF THE MICROWAVE OVEN IS STILL LIVE DURING SERVICING AND PRESENTS A HAZARD.

Therefore, before checking the performance of the touch control panel,

1) Disconnect the power supply cord, and then remove

outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Disconnect the leads to the primary of the power

transformer.

5) Ensure that these leads remain isolated from other

components and oven chassis by using insulation tape.

6) After that procedure, re-connect the power supply

cord.

After checking the performance of the touch control panel,

1) Disconnect the power supply cord.

2) Open the door and block it open.

3) Re-connect the leads to the primary of the power

transformer.

4) Re-install the outer case (cabinet).

2SD1859

R-430DK R-430DW R-430DQ R-440DK R-440DW

5) Re-connect the power supply cord after the outer case is installed.

6) Run the oven and check all functions.

A. On some models, the power supply cord between the

touch control panel and the oven itself is so short that the two can’t be separated. For those models, check and repair all the controls (sensor-related ones included) of the touch control panel while keeping it connected to the oven.

B. On some models, the power supply cord between the

touch control panel and the oven proper is long enough that they may be separated from each other. For those models, it is possible to check and repair the controls of the touch control panel while keeping it apart from the oven proper; in this case you must short both ends of the door sensing switch (on PWB) of the touch control panel with a jumper, which activates an operational state that is equivalent to the oven door being closed. As for the sensor-related controls of the touch control panel, checking them is possible if dummy resistor(s) with resistance equal to that of the controls are used.

(2)Servicing the touch control panel with power supply

from an external power source:

Disconnect the touch control panel completely from the oven proper, and short both ends of the door sensing switch (on PWB) of the touch control panel, which activates an operational state that is equivalent to the oven door being closed. Connect an external power source to the power input terminal of the touch control panel, then it is possible to check and repair the controls of the touch control panel it is also possible to check the sensorrelated controls of the touch control panel by using the dummy resistor(s).

3. Servicing Tools

Tools required to service the touch control panel assembly.

1) Soldering iron: 30W (It is recommended to use a soldering iron with a grounding terminal.)

2) Oscilloscope: Single beam, frequency range: DC-10MHz type or more advanced model.

3) Others: Hand tools

4. Other Precautions

1) Before turning on the power source of the control unit, remove the aluminium foil applied for preventing static electricity.

2) Connect the connectors of the key unit to the control unit being sure that the lead wires are not twisted.

3) After aluminium foil is removed, be careful that abnormal voltage due to static electricity etc. is not applied to the input or output terminals.

4) Attach connectors, electrolytic capacitors, etc. to PWB, making sure that all connections are tight.

5) Be sure to use specified components where high precision is required.

R-430DK R-430DW R-430DQ R-440DK R-440DW

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

WARNING AGAINST HIGH VOLTAGE:

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may result in severe, possibly fatal, electric shock. (Example) High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..

WARNING:

Avoid possible exposure to microwave energy. Please follow the instructions below before operating the oven.

1. Disconnect the power supply cord.

2. Make sure that a definite” click” can be heard when the microwave oven door is unlatched. (Hold the door in a closed position with one hand, then push the door open button with the other, this causes the latch leads to rise, it is then possible to hear a “click’ as the door switches operate.)

3. Visually check the door and cavity face plate for damage (dents, cracks, signs of arcing etc.).

Carry out any remedial work that is necessary before operating the oven. Do not operate the oven if any of the following conditions exist;

WARNING FOR WIRING

To prevent an electric shock, take the following precautions.

1. Before wiring,

1) Disconnect the power supply cord.

2) Open the door block it open.

3) Discharge the high voltage capacitor and wait for 60 seconds.

2. Don’t let the wire leads touch to the following parts;

1) High voltage parts: Magnetron, High voltage transformer, High voltage capacitor and High voltage rectifier assembly.

2) Hot parts: Oven lamp, Magnetron, High voltage transformer and Oven cavity.

1. Door does not close firmly.

2. Door hinge, support or latch hook is damaged.

3. The door gasket or seal is damaged.

4. The door is bent or warped.

5. There are defective parts in the door interlock system.

6. There are defective parts in the microwave generating and transmission assembly.

7. There is visible damage to the oven.

Do not operate the oven:

1. Without the RF gasket (Magnetron).

2. If the wave guide or oven cavity are not intact.

3. If the door is not closed.

4. If the outer case (cabinet) is not fitted.

3) Sharp edge:

Bottom plate, Oven cavity, Waveguide flange, Chassis support and other metallic plate.

4) Movable parts (to prevent a fault)

Fan blade, Fan motor, Switch, Switch lever, Open button.

3. Do not catch the wire leads in the outer case cabinet.

4. Insert the positive lock connector until its pin is locked and make sure that the wire leads do not come off even if the wire leads are pulled.

5. To prevent an error function, connect the wire leads correctly, referring to the Pictorial Diagram.

Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any of the following removal procedures:

OUTER CASE REMOVAL

To remove the outer case, proceed as follows.

1. Disconnect the power supply cord.

2. Open the oven door and block it open.

3. Remove the two (2) screws from the lower portion of the rear cabinet using a T20H Torx type or GTXH20-100 screw driver.

4. Remove the remaining two (2) screws from rear and four (4) screws along the right side of outer case.

5. Slide the entire outer case back out about 1 inch (3 cm) to free it from retaining clips on the cavity face plate.

6. Lift entire outer case from the unit.

CAUTION: 1. DISCONNECT OVEN FROM POWER SUP

PLY BEFORE REMOVING OUTER CASE.

2. DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS OR WIRING.

NOTE: When replacing the outer case, the 2 special

Torx screws must be reinstalled in the same locations.

POWER TRANSFORMER REMOVAL

1. Disconnect the power supply cord and then remove outer case.

2. Open the oven door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect wire leads (primary and high voltage) from power transformer and the filament leads from the magnetron and capacitor terminals.

5. Remove four (4) screws holding transformer to bottom plate.

6. Remove transformer from bottom plate.

R-430DK R-430DW R-430DQ R-440DK R-440DW

Special screw

Screw Driver (Type: TORX T20 H or GTXH20-100)

Re-install

1. Rest transformer on the bottom plate with its primary terminals toward the oven face plate.

Secure transformer with four screws to bottom plate.

3. Re-connect wire leads (primary and high voltage) to power transformer and filament leads of transformer to magnetron and high voltage capacitor. Refer to "PICTORIAL DIAGRAM" on page 33.

4. Re-install outer case and check that oven is operating properly.

HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL

1. Disconnect the power supply cord and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the high voltage wire A from the high voltage capacitor.

5. Disconnect the high voltage wire of high voltage rectifier assembly from the magnetron.

6. Disconnect the filament lead (short one) of the power transformer from the high voltage capacitor.

MAGNETRON REMOVAL

Removal

1. Disconnect the power supply cord and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect wire leads from magnetron.

5. Remove the two (2) screws holding the chassis support to the magnetron and the oven cavity front flange.

6. Slide the magnetron duct slightly so that the two (2) screws at left hand side of the magnetron appear.

7. Carefully remove the four (4) screws holding magnetron to waveguide flange.

8. Remove the magnetron with care so that the magnetron antenna is not hit by any metal object around the antenna.

9. Now, the magnetron is free.

7. Remove one (1) screw holding capacitor holder with the high voltage rectifier to the base plate.

8. Disconnect rectifier terminal from capacitor. High voltage rectifier assembly is now free.

9. Remove capacitor holder. Capacitor is now free.

CAUTION: WHEN REPLACING HIGH VOLTAGE RECTI-

FIER AND HIGH VOLTAGE CAPACITOR, GROUND SIDE TERMINAL OF THE HIGH VOLTAGE RECTIFIER MUST BE SECURED FIRMLY WITH A GROUNDING SCREW.

Re-install

1. Re-install the magnetron to waveguide flange with care to prevent damage to the magnetron antenna.

2. Secure the magnetron with the four (4) screws.

3. Hold the chassis support to the oven cavity front plate and the magnetron with the two (2) screws.

4. Reconnect the wire leads to the magnetron. Refer to "PICTORIAL DIAGRAM" on page 33.

5. Re-install outer case and check that the oven is operating properly.

CAUTION: WHEN REPLACING MAGNETRON, BE SURE

THE R.F. GASKET IS IN PLACE AND MOUNTING SCREWS ARE TIGHTENED SECURELY

R-430DK R-430DW R-430DQ R-440DK R-440DW

Disconnect the power supply cord and remove outer case.

OVEN LAMP AND LAMP SOCKET REMOVAL

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Remove the oven lamp from the oven lamp socket.

5. Pull the wire leads from the oven lamp socket by pushing the terminal hole of the oven lamp socket with the small flat type screw driver.

6. Remove the oven lamp socket from the magnetron duct by turning the socket counterclockwise.

7. Remove the oven lamp from the socket by turning the oven lamp.

8. Now, the oven lamp and the oven lamp socket are free.

POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Push the lever of positive lock® connector.

5. Pull down on the positive lock® connector.

Figure C-1. Oven lamp socket

CAUTION: WHEN CONNECTING THE POSITIVE LOCK

CONNECTORS TO THE TERMINALS, CONNECT THE POSITIVE LOCK® SO THAT THE LEVER FACES YOU.

CONTROL PANEL ASSEMBLY REMOVAL (R-430DK/DW/DQ)

1. Disconnect the power supply cord and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the wire leads from panel components.

5. Remove the one (1) screw holding the control panel assembly to the oven cavity front plate.

6. Slide the control panel assembly upward and remove it.

7. Now, individual components can be removed.

NOTE: 1. Before attaching a new key unit, wipe off remaining

adhesive on the control panel frame surfaces completely with a soft cloth soaked in alcohol.

2. When attaching the key unit to the control panel frame, adjust the upper edge and right edge of the key unit to the correct position of control panel frame.

Figure C-2. Positive lock® connector

3. Stick the key unit firmly to the control panel frame by rubbing with soft cloth not to scratch.

LSI UNIT NOTE: Handle the LSI unit carefully so that there is no

excessive force applied to the ribbon connection.

Ribbon cable

Liquid Crystal

Display (LCD)

of LSI unit

Printed wiring board

TURNTABLE MOTOR REMOVAL

1. Disconnect the power supply cord.

2. Remove turntable and turntable support from oven cavity.

3. Lay the oven on it's backside. Remove the turntable motor cover by snipping off the material in four corners.

4. Where the corners have been snipped off bend corner areas flat. No sharp edges must be evident after removal of the turntable motor cover.

LSI unit

5. Disconnect wire leads from turntable motor. (See "Positive lock connector removal")

6. Remove one (1) screw holding turntable motor to oven cavity.

7. Now the turntable motor is free.

8. After replacement use the one (1) screw to fit the turntable motor cover.

COOLING FAN MOTOR REMOVAL

REMOVAL

1. Disconnect the power supply cord and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the wire leads from the fan motor.

5. Remove the two (2) screws holding the fan motor to the oven cavity back plate.

6. Remove the fan blade from the fan motor shaft according to the following procedure.

7. Hold the edge of the rotor of the fan motor by using a pair of groove joint pliers.

CAUTION: * Make sure that no metal pieces enter the gap between

the rotor and the stator of the fan motor because the rotor is easily shaven by pliers and metal pieces may be produced.

* Do not touch the pliers to the coil of the fan motor

because the coil may be cut or injured.

* Do not disfigure the bracket by touching with the

pliers.

8. Remove the fan blade from the shaft of the fan motor by pulling and rotating the fan blade with your hand.

9. Now, the fan blade and the fan motor will be free.

R-430DK R-430DW R-430DQ R-440DK R-440DW

CAUTION: * Do not reuse the removed fan blade because the hole

(for shaft) may be larger than normal.

INSTALLATION

1. Install the fan blade to the fan motor shaft according to the following procedure.

2. Hold the center of the bracket which supports the shaft of the fan motor on the flat table.

3. Apply the screw lock tight into the hole (for shaft) of the fan blade.

4. Install the fan blade to the shaft of fan motor by pushing the fan blade with a small, light weight, ball peen hammer or rubber mallet.

CAUTION: * Do not hit the fan blade strongly when installed

because the bracket may be disfigured.

* Make sure that the fan blade rotates smooth after

installation.

* Make sure that the axis of the shaft is not slanted.

5. Install the fan motor to the the oven cavity back plate with the two (2) screws.

6. Connect the wire leads to the fan motor, referring to the pictorial diagram.

Rear View

Side View

AH SENSOR REPLACEMENT

REMOVAL

Disconnect the power supply cord and remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Remove the two (2) screws holding the AH sensor to the sensor duct.

5. Disconnect the AH sensor harness from the connector CN-F on control unit.

6. AH sensor is now free

RE-INSTALL

Insert the new AH sensor into the sensor duct.

2. Install two (2) screws to secure the AH sensor.

3. Route the AH sensor harness across the oven cavity top plate and through the large opening.

4. Connect the AH sensor harness to CN-F on control unit.

5. Re-install the outer case cabinet and check for proper operation.

DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL

Disconnect the power supply cord and remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect wire leads from the switches.

Remove two (2) screws holding latch hook to oven flange.

6. Remove latch hook assembly from oven flange.

7. Push outward on the two (2) retaining tabs holding switch in place.

8. Switch is now free. At this time switch lever will be free, do not lose it.

Re-install

1. Re-install each switch in its place. The secondary interlock/ monitor switches are in the lower position and the door sensing switch is in the upper position.

2. Re-connect wire leads to each switch. Refer to pictorial diagram.

R-430DK R-430DW R-430DQ R-440DK R-440DW

3. Secure latch hook (with two (2) mounting screws) to oven flange.

and check continuity of the monitor circuit. Refer to chapter

"Test Procedure" and Adjustment procedure.

4. Make sure that the monitor switch is operating properly

DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

If the door sensing switch, secondary interlock switch and monitor switch do not operate properly due to a

misadjustment, the following adjustment should be made.

4. Loosen the two (2) screws holding latch hook to the oven cavity front flange.

5. With door closed, adjust latch hook by moving it back and

forth, and up and down. In and out play of the door allowed

by the upper and lower position of the latch hook should be less than 0.5mm. The vertical position of the latch hook should be adjusted so that the door sensing switch and secondary interlock switch are activated with the door closed. The horizontal position of the latch hook should be adjusted so that the plunger of the monitor switch is pressed with the door closed.

6. Secure the screws with washers firmly.

7. Check the operation of all switches. If each switch has not activated with the door closed, loosen screw and adjust the latch hook position.

hook, pushing and pulling upper portion of door toward the oven face. Both results (play in the door) should be less than 0.5mm.

2. The door sensing switch and secondary interlock switch interrupt the circuit before the door can be opened.

3. Monitor switch contacts close when door is opened.

4. Re-install outer case and check for microwave leakage around door with an approved microwave survey meter. (Refer to Microwave Measurement Procedure.)

Latch Heads

Door

Switch Lever

Door Sensing Switch

Monitor Switch

After adjustment, check the following.

1. In and out play of door remains less than 0.5mm when in the latched position. First check upper position of latch hook, pushing and pulling upper portion of door toward the oven face. Then check lower portion of the latch

DOOR REPLACEMENT

REMOVAL

1. Disconnect the power supply cord.

2. Push the open button and open the door slightly.

3. Insert a putty knife (thickness of about 0.5mm) into the gap between the choke cover and door frame as shown in Figure C-4 to free engaging parts.

4. Pry the choke cover by inserting a putty knife as shown Figure C-4.

5. Release choke cover from door panel.

6. Now choke cover is free.

7. Release two (2) pins of door panel from two (2) holes of upper and lower oven hinges by lifting up.

8. Now, door panel with door frame is free from oven cavity.

Choke Cover

Door Frame

Putty Knife

Figure C-4. Door Disassembly

Secondary Interlock Switch

Figure C-3. Latch Switch Adjustments

9. Release the door panel from twelve (12) tabs of door frame.

10.Remove the door panel from the door frame.

11.Now, door panel with sealer film is free.

12.Tear sealer film from door panel.

13.Now, door panel is free.

14.Slide latch head upward and remove it from door frame with releasing latch spring from door frame and latch head.

15.Now, latch head and latch spring are free.

16.Remove door screen from door frame

17.Now, door frame is free.

RE-INSTALL

1. Re-install door screen to door frame.

2. Re-install the latch spring to the latch head. Re-install the latch spring to the door frame. Re-install latch head to door frame.

3. Re-install door panel to door frame by fitting twelve (12) tabs of door frame to twelve (12) holes of door panel.

4. Put sealer film on door panel. Refer to “Sealer Film” about how to handle new one.

5. Catch two (2) pins of door panel on two (2) hole of upper and lower oven hinges.

6. Re-install choke cover to door panel by pushing.

Note: After any service to the door; (A) Make sure that door sensing switch and secondary

interlock switch are operating properly. (Refer to chapter “Test Procedures”.).

(B) An approved microwave survey meter should be

used to assure compliance with proper microwave radiation emission limitation standards.

After any service, make sure of the following :

1. Door latch heads smoothly catch latch hook through latch holes and that latch head goes through center of latch hole.

2. Deviation of door alignment from horizontal line of cavity face plate is to be less than 1.0mm.

3. Door is positioned with its face pressed toward cavity face plate.

4. Check for microwave leakage around door with an approved microwave survey meter. (Refer to Microwave Measurement Procedure.)

Note: The door on a microwave oven is designed to act as

an electronic seal preventing the leakage of microwave energy from oven cavity during cook cycle. This function does not require that door be airtight, moisture (condensation)-tight or light-tight. Therefore, occasional appearance of moisture, light or sensing of gentle warm air movement around oven door is not abnormal and do not of themselves indicate a leakage of microwave energy from oven cavity.

R-430DK R-430DW R-430DQ R-440DK R-440DW

SEALER FILM

Installation

1. Put the adhesive tape on the backing film of the sealer film as shown in Fig. C-6.

2. Tear the backing film by pulling the adhesive tape.

3. Put the pasted side of the sealer film on the door panel

Figure C-6. Sealer film

Figure C-5. Door Replacement

R-430DK

R-430DW

R-430DQ

R-440DK

CAVITY TEMP. FUSE

WHT

DOOR SENSING

CONTROL UNIT

SWITCH

COM.

N.O.

PNK

GRN

WHT

MAGNETRON TEMP. FUSE

RED

NOTE: The grounding conductor of the power supply cord has been grounded by power supply cord fixing screw. The screw must always be kept tight.

RED

WHT GRY

POWER SUPPLY CORD 120V 60Hz

R-440DW

(LSI UNIT)

BLK

ORG

BLU

CN-B

(POWER UNIT)

RY1

N.O.

1 2

CN-A

PRIMARY INTERLOCK RELAY

COM.

RY2

N.O.

to Oven cavity

GRN

PNK

CN-B

WHT

CN-A

BRN

BLU

RED RED

GRN

RED

N.C.

MONITOR SWITCH

SECONDARY INTERLOCK SWITCH

COM.

WHT WHT

GRY WHT

RED

MONITOR

FUSE

HOLDER

BLK

TURNTABLE MOTOR

WHT

OVEN LAMP AND SOCKET

BRN

ORG

BLUE MARK

NOTE: Hot (ORG) wire must be connected to the terminal with blue mark on the oven light socket.

MAGNETRON

RED

WHT WHT

NOTE: The neutral (WHT/GRY) wire must be connected to the terminal with "N" mark on the power supply cord.

WHT ORG ORG

FAN MOTOR

HIGH VOLTAGE COMPONENTS

HIGH VOLTAGE WIRE A

HIGH VOLTAGE CAPACITOR

POWER TRANSFORMER

H.V. RECTIFIER

Figure S-1. Pictorial Diagram R-430DK/DW/DQ

CN-F

BLK

RED

2 3

WHT

CONTROL UNIT

CN-G

PRIMARY INTERLOCK RELAY

CN-A

RY2

CN-C

IC1

CN-C

CN-B

(CPU UNIT)

ORG

BLU

(UPPER)

BLK

(LOWER)

(POWER UNIT)

RY1

CN-F

RED RED

AH SENSOR

GRN

PNK

CN-B

WHT

CN-A

BRN

B LU

to Oven cavity

RED

N.C.

MONITOR SWITCH

SECONDARY INTERLOCK SWITCH

COM.

DOOR SENSING SWITCH

COM.

GRN

COM.

WHT WHT

N.O.

WHT

GRY

WHT

CAVITY TEMP. FUSE

WHT

PNK

GRN

RED

MONITOR

FUSE

HOLDER

BLK

WHT

MAGNETRON TEMP. FUSE

RED

TURNTABLE MOTOR

WHT

OVEN LAMP AND SOCKET

BRN

RED

WHT WHT

NOTE: The grounding conductor of the power supply cord has been grounded by power supply cord fixing screw. The screw must always be kept tight.

ORG

BLUE MARK

NOTE: Hot (ORG) wire must be connected to the terminal with blue mark on the oven light socket.

HIGH VOLTAGE COMPONENTS

MAGNETRON

RED

WHT GRY

ORG ORG

POWER TRANSFORMER

POWER SUPPLY CORD 120V 60Hz

NOTE: The neutral (WHT/GRY) wire must be connected to the terminal with "N" mark on the power supply cord.

WHT

HIGH VOLTAGE WIRE A

H.V. RECTIFIER

FAN MOTOR

HIGH VOLTAGE CAPACITOR

Figure S-1. Pictorial Diagram R-440DK/DW

R-430DQ

R-440DK

R-440DW

R-430DK

R-430DW

R-430DK R-430DW R-430DQ R-440DK R-440DW

CN-A

A 1

A 2

VRS1

(J1)

10G471K

134

R4 27

D1-D4 11ES1

1SS270A1SS270A

+ –

C1 0.1µ/50v

OVEN LAMP TURNTABLE MOTOR FAN MOTOR

COM

RY1

D7D8

1SS270A1SS270A

Q3 KRC243M

MICRO

DOOR SENSING SWITCH

COM

B 2

RY2

CN-C 12PIN LEAD

Q2 2SB1238

C2 1000µ/35v

Q1 2SB1238

R2 680 1/2w

R1 2.4k

ZD1

R5 4.7k

HZ16-1

C3 0.1µ/50v

R3 510 1/2w

SP1 PKM22EPT

R6 3.3k

–

C5 10µ/35v

–

C4 10µ/35v

C10

C 2

C 3

C 1 C 4 C 9

C 5

C 6

C 7

C 8

C11

C12

WIRE HARNESS LED

GND

VA INT VR

BUZZER OVEN LAMP

TURNTABLE MOTOR FAN MOTOR

MICRO

NC DOOR

SENSING SWITCH

Figure S-2(a). Power Unit Circuit for R-430DK/DW/DQ

C 3

INT

C 5

C 6

C 4

C11

C10

C 9

C 7

C 8

C 2

C 1

GND

BZ/EN

BUZZR OVEN LAMP

FAN MOTOR TURNTABLE MOTOR

MICRO

N.C

N.C DOOR

SENSING SWITCH

CN-C

R2 91 1w

CN-A

A 2 A 1

VRS1

(J1)

10G471K

GND

D1 S1NB10

+ –

C2 1000µ/35v

AC120V 60Hz

Q1 2SD1859

2.4k

1/4w

SP30

R3 91 1w

ZD1

HZ16-1

OVEN LAMP FAN MOTOR TURNTABLE MOTOR

MICRO

DOOR SENSING

SWITCH

COM

B 2

B 1

NOTE

RY1

RY2

: IF NOT SPECIFIED, 0.1µF / 50V

11P LEAD WIRE HARNESS

Figure S-2(b). Power Unit Circuit for R-440DK/DW

INT GND

VC LED

C-4 C-2

C-3

LD10 LD11 LD12

C-10

BUZZER

OVEN LAMP

TURNTABLE MOTOR FAN MOTOR

MICRO

(BROWNER)

DOOR SENSING

SWITCH

C-9

C-1

C-5

C-6

C-7

C-8

C-12

C-11

LD19 LD18 LD17

D20 1SS355

D41 1SS355

+ –

C10 47µ/16v

LD13LD14LD15

LD16

Q30 DTA143EKA

Q20 DTA143EKA

Q21 DTA123JKA

C11 0.1µ/50v

R90 330 1w

C12

0.1µ

/50v

R96 3.57KDR91 3.32KD

C20

0.1µ /50v

Q11 DTA143EKA

R12 15k

D90 MA152WA

C90

0.1µ

/50v

R92 1.8kF

C13

0.01µ

/25v

56 IC2 BA4558 1234

CPU UNIT

R10 1k

Q10 2SA 1037AK

ZD10

UDZ4.3B

R93 360kF

R102 37.4kF

R101 75kF

R100 150kF

EDCBA

C14

0.01µ

/25v

(J10) (J11)

R11 15k

R94 10k R95 47k

C91

0.015µ/25v

R97 47k

R99 300k

R98 620k

R40 4.7k

R41 15k

(J12)

4.7K

(J13)

4.7K

C92

0.01µ

/25v

C40 0.01µ/25v

(J14)

(J17) (J16)

(J15)

4.7K

C93 0.01µ/25v

4.7K

CF1 CST4.00MGW

GND

Indicator Circuit ( See Fig. S-4 )

S 9

S 8

S 7

S 6

S 5

S 4

S 3

S 2

S 1

P02

INTP1

S 0

VSS0

P03

P04

P05

P110

P111

P112

P113

S20

S19

S18

S17

S16

S15

S14

S13

S12

S11

P71

I C

P72

IC1 IXA037DR

X 2

X 1

XT1

VDD1

S10

XT2

INTP0

RESET

S22 S23 P97 P96 P95 P94 P93 P92 P91 P90 P87 P86 P85 P84 P83 P82 P81 P80

100

P25

P26

P27

P70

130

R80

VLC2

P114

VLC1

P115

VLC0

P116

BIAS

P117

COM3

ANI0

AVSS

COM2

COM1

ANI1

5180

COM0

ANI2

P37S21 P36 P35 P34 P33 P32 P31

P30 P103 P102 VSS1 P101 P100

AVREF

VDD0 ANI7 ANI6 ANI5 ANI4 ANI3

E D C B A

F-1 F-2 F-3

CN-F AH SENSOR

R67

15k

R66

15k

R65

15k

R64

15k

R63

15k

R62

15k

R61

15k

R60

Fresh

vegetables

Ground

meat

Frozen entrees

15k

R-430DQ

R-440DK

R-440DW

R-430DK

R-430DW

NOTE

: IF NOT SPECIFIED 1/10W ± 5%

ANI6

ANI7

P100

P101

P102

P103

R68 15k

R69 15k

R70 15k

R71 15k

R72 15k

R73 15k

R79 270k

R78 270k

R77 270k

R76 270k

R75 270k

R74 270k

C65 330p/50v

C64 330p/50v

C63 330p/50v

C62 330p/50v

C61 330p/50v

C60 330p/50v

G 8 G 7 G 6 G 5 G 4 G 3 G 2 G 1

Start

Touch On Breakfast

Bar

Super

Defrost

Beverage

center

Compu Defrost

Fish/

seafood

Poultry Frozen

vegetables

54321

G 9

09876

G10G11G12

Minute

G13

G14

Plus

One Dish

Dinners

Popcorn

KEY UNIT

Frozen snacks

Stop

Clear

Sensor reheat

Lunch on

Clock

the Run

Baked

potatoes

Kitchen

Timer

Power

Level

Custom

Help

Rice

Figure S-3(a). CPU Unit Circuit R-430DK/DW/DQ

R-430DK

R-430DW

R-430DQ

R-440DK

R-440DW

+ –

C10 10µ/35v

C11 0.1µ/50v

C17 0.1µ/50v

R40 330 1w

0.1µ/50v

C44

C45

R41 3.32kD

C41

0.015µ /25v

GND

INT

AH SENSOR

D40 MA152WK

–

Q30 KRA101S

C11

C10

D21 MA152WK

C30 10µ/35v

R30 3.3k

Q31 KRC101S

Q32 KRC101S

Q20 KRA102S

Q22 KRC101S

+ –

C22

10µ

Q21 KRC101S

BUZZER ENV.

BUZZER

OVEN LAMP TURNTABLE MOTOR FAN MOTOR

MICROR

C12 0.1µ/50v

R42

3.57kD

C40 0.1µ/50v

IC3

R47 47k R48 620k R49 300k R50 150kF R51 75kF R52 37.4kF

/35v

R10 470 1/2w

Q10 KTC1027

R11

1.2k

1/4w

R45 10k

R46 47k

C21

0.1µ

/25v

ZD10

UDZ5.6B

R43 1.8kF

R44 360kF

C20

0.01µ /25v

R21 4.7k

+ –

C13 47µ/16v

C43 0.01µ/25v

C42 0.01µ/25v

VCC 85 14

IC6

M51953AFP

C16 0.01µ/25v

GND

Q12 KRC101S

C14 0.01µ/25v

R13 4.7k

(R101) 4.7k

(J10) 4.7k

(J12)

(J11)

(J13) 4.7k

CF1

CST12.00MTW

8079787776757473727170696867666564636261605958575655545352

Vref

AN0

MD2

MD1

MD0

Avcc

P81 P82

Vss PA0 PA1 PA2 PA3 PA4 PA5

Vcc

A20

TI0CA2

2345678

LWR

PB1

PB2

PB3

TM00

AN1

AN2

AN3

AN4

AN5

AN6

DA1

Avss

IR00

90 91 92

CS1

CS0

94 95 96 97 98 99

100

VCC

R80

4.7k

C15 0.1µ/25v

C130 0.01µ/25v

C18

0.1µ /25v

Vcc

Vss

P67

P62

P61

A19

A18

NMI

HWR

XTAL

EXTAL

A17

RES

WAIT

STBY

IC1 IXA029DR

Vss

PB4

PB5

PB6

PB7

TxD0

RES0

101112131415161718192021222324252627282930

Vss

P91

P93

P94

P95

P40

P41

P42

P43

P44

RxD0

IC3

+ Q80 KTC1027

D80

D80-81

1SS355

D81

(J80)

A16

A15

A14

A13

A12

A11

A10

Vss

Vcc

D15

D14

D13

D12

D11

D10

P45

P46

P47

WH-1 WH-1

R82

3.3k

1/4w

R81 27

0 ohm

LED1 LED2

A13 28 29

A11

A10

IC2

A18

IXA030DR

A17

4142434445

CPU UNIT

26252423222120

A14

A15

A16

GND

BYTE

D15/A-1

A2A1A0

GND

123

D14

D6A12

D13

D12

VCC

GND

D11

D10

C19 0.1µ/25v

C97 0.1µ/25v

R91 18kF

C96 0.1µ/25v

R98 1M

R90 43kF

TH1

5G2M40B333J

R92 20kF

46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9 8 7 6 5 4 3 2 1

C91 0.1µ/25v

C92 0.1µ/25v

C93 0.1µ/25v

C94 0.1µ/25v

C95 0.1µ/25v

GND1

VLCD1

VCC1

V50 V40 V30 V20 V10

GREF IREFM IREFP VLCD2 VLCD3

VCC2

GND2

GND3

VCC3

OSC1

OSC2

OSC

DCON

CL1 FLM

M M/S RES

CS RS

RD VCC4 GND4

DB0 DB1 DB2 DB3 DB4 DB5 DB6

DB7 VCC5 GND5 VCC6

VLCD4

GND6

COM100 COM99 COM98

COM51 SEG160 SEG159 SEG158

IC5 IXA031DR

SEG3 SEG2

SEG1 COM50 COM49

COM3

COM2

COM1

LIQUID CRYSTAL DISPLAY

100 x 160 Dots

DOOR SENSING SWITCH

CN-C

D20 MA152WK

R68 15k

R69 15k

R70 15k

R71 15k

R72 15k

R73 15k

R20 15k

C64 330pF/50v

C63 330pF/50v

C65 330pF/50v

C62 330pF/50v

C61 330pF/50v

C60 330pF/50v

R79 270k

R78 270k

R77 270k

R76 270k

R75 270k

R74 270k

C98

0.01µ

R113

/25v

C112

0.1µ /25v

150

1/2w

R111

4.7k

R110

Vcc

R65 15k

R64 15k

R63 15k

R62 15k

R61 15k

R67 15k

R66 15k

G 1

G 2 G 3 G14 G 7 G 8 G 9 G10 G14

Sharp R-43040D, R-430DW, R-430DQ, R-440DK, R-440DW Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual