SHARP PQ033ES1MXP, PQ050ES1MXP Technical data

查询PQ033ES1MXP供应商
Under development
PQ033ES1MXP PQ050ES1MXP
Low Power-Loss Voltage Regulator
New product
Low Output Current, Compact Surface Mount Type Low Power-Loss Voltage Regulators
Features
(1)
Compact package : TO-92 type
(Size(mold part) 5.2 × 5.5 × 4.2 mm)
(2) Small current output : 100 mA(MAX.) (3) Low consumption current :
Quiescent current Iq=MAX. 350 µA
(4) Low power-loss :
Dropout voltage : MAX. 0.26 V at Io=60 mA Dropout voltage : MAX. 0.4 V at Io=150 mA
(5)
Built-in overcurrent, overheat protection functions
(6) Taped package
Applications
(1) TV (2) VCR (3) Air conditioner (4) DVD player (5) Audio equipment
5.2(MAX)
AX)
AX)
5.5(M
2.3(M
±0.7
IN)
3.0
IN)
10.0(M
12.7(M
2.5±
1
0.4
0.1
Internal connection
DC output(Vo)
1
GND
2
DC input(Vin)
3
R2.4
3
2
2.5±
0.6(MAX)
0.4
0.1
0.45±0.1
3
Control circuit
(Unit: mm)
4.2(MAX)
1.4±0.1
0.4±0.05
1
2
Absolute Maximum Ratings
(Ta=25°C)
Parameter Symbol Ratings Unit
*1
Input voltage Output current
*2
Power dissipation
*3
Junction temperature Operating temperature Storage temperature Soldering temperature
(Notice)
•In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
•Specifications are subject to change without notice for improvement.
(Internet)
•Data for Sharp's optoelectronic/power devices is provided on internet. (Address http://sharp-world.com/ecg/)
1/2
Vin
Io
Pd
Tj
Topr
Tstg Tsol
16 150 520 150
-30 to +80
-55 to +150
260(For 10s)
V
mA
mW
°C °C °C °C
*1 All are open except GND
and applicable terminals. *2 At mounted condition *3 Overheat protection may operate
at 125Tj150°C.
D5-020902
PQ033ES1MXP PQ050ES1MXP
Electrical Characteristics
Parameter
Output voltage
Load regulation
Line regulation Temperature coefficient of output voltage
Ripple rejection Dropout voltage Quiescent current
*4 Dropout voltage when output voltage lowers 0.1V from the voltage at Vin=Vo+1V.
Symbol
Vo RegL1 RegL2 RegL3
RegI
TcVo
RR
Vi-o1 Vi-o2
Iq
Low Power-Loss Voltage Regulator
(Unless otherwise specified, Vin=Vo(TYP.)+1.0V, Io=30mA.Ta=25°C)
Conditions
­Io=5mA to 60mA Io=5mA to 100mA Io=5mA to 150mA Vin=
Vo(TYP.)+1V to
Vo(TYP.)+6V
Io=10mA, Tj=-25 to +75°C
­Io=60mA, Vin=*4 Io=150mA, Vin=*4 Io=0mA
10 20 30
3.0
55
0.2
170
MAX.
50 100 160
20
-
-
0.26
0.4
350
MIN.
Refer to the table below.
TYP.
-
-
-
-
0.05
-
-
0.11
-
-
-
Unit
V mV mV mV
mV
mV/°C
dB
V
V
µA
Output Voltage Line-up
Parameter Symbol Conditions MIN. TYP. MAX. Unit
Output voltage
PQ033ES1MXP PQ050ES1MXP
(Vin=Vo(TYP.)+1.0V, Io=30mA.Ta=25°C)
V
O
V
3.234
4.900
3.3
5.0
3.366
5.100
2/2
As of September 2002
D5-020902
NOTICE
The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice.
Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions:
(i) The devices in this publication are designed for use in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when
SHARP devices are used for or in connection with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of
reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g., scuba).
If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices.
This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party.
Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
Loading...